| Age | Commit message (Collapse) | Author |
|---|
|
QUEUE_FLAG_DEAD is used to indicate that queuing new requests must
stop. After this flag has been set queue draining starts. However,
during the queue draining phase it is still safe to invoke the
queue's request_fn, so QUEUE_FLAG_DYING is a better name for this
flag.
This patch has been generated by running the following command
over the kernel source tree:
git grep -lEw 'blk_queue_dead|QUEUE_FLAG_DEAD' |
xargs sed -i.tmp -e 's/blk_queue_dead/blk_queue_dying/g' \
-e 's/QUEUE_FLAG_DEAD/QUEUE_FLAG_DYING/g'; \
sed -i.tmp -e "s/QUEUE_FLAG_DYING$(printf \\t)*5/QUEUE_FLAG_DYING$(printf \\t)5/g" \
include/linux/blkdev.h; \
sed -i.tmp -e 's/ DEAD/ DYING/g' -e 's/dead queue/a dying queue/' \
-e 's/Dead queue/A dying queue/' block/blk-core.c
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Chanho Min <chanho.min@lge.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Before queuing the flip but crucially after attaching the unpin-work to
the crtc, we continue to setup the unpin-work. However, should the
hardware fire early, we see the connected unpin-work and queue the task.
The task then promptly runs and unpins the fb before we finish taking
the required references or even pinning it... Havoc.
To close the race, we use the flip-pending atomic to indicate when the
flip is finally setup and enqueued. So during the flip-done processing,
we can check more accurately whether the flip was expected.
v2: Add the appropriate mb() to ensure that the writes to the page-flip
worker are complete prior to marking it active and emitting the MI_FLIP.
On the read side, the mb should be enforced by the spinlocks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
[danvet: Review the barriers a bit, we need a write barrier both
before and after updating ->pending. Similarly we need a read barrier
in the interrupt handler both before and after reading ->pending. With
well-ordered irqs only one barrier in each place should be required,
but since this patch explicitly sets out to combat spurious interrupts
with is staged activation of the unpin work we need to go full-bore on
the barriers, too. Discussed with Chris Wilson on irc and changes
acked by him.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
If the sdata work is pending while the interface is stopped,
we currently flush it. If it's not running this means waiting
for it to run, which could take a while if the workqueue is
backlogged. However, the work exits right away if it starts
to run while the interface is already stopping. There's no
point in waiting for that, so use cancel_work_sync() instead.
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This is really a 3-bit field, not a single bit,
so declare a mask and shift. Also fix hwsim, it
advertises the maximum possible.
While at it reindent all the defines using tabs
instead of spaces.
Change-Id: I7cd81c0d72f76deb5010aba5bfa3dd312006e898
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Previously, mesh peering frames from a STA without a station
entry were being dropped.
Mesh Peering Open and other frames (WLAN_CATEGORY_SELF_PROTECTED)
are valid mesh peering frames even if received from a yet unknown
station; the STA entry will be created in mesh_peer_init later.
The problem didn't occur previously since both STAs receive each
other's beacons which created the STA entry. However, this causes
an unnecessary delay and beacons might not be received if either
node is in PS mode.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
[reword commit log a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We no longer need the connector.
But we need libcrc32c.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
This was introduces when moving the code over from the 8.3 codebase
with commit 328e0f125bf41f4f33f684db22015f92cb44fe56
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
drbd_set_role(, R_PRIMARY, ) does the state change to Primary,
some more housekeeping, and possibly generates a new UUID set.
All of this holding the "state_mutex".
The connection handshake involves sending of various state information,
including the current data generation UUID set, and two connection
state changes from C_WF_CONNECTION to C_WF_REPORT_PARAMS further to
a number of different outcomes, resync being one of them.
If the connection handshake happens between the state change to Primary
and the generation of the new UUIDs, the resync decision based on the
old UUID set may be confused, depending on circumstances.
Make sure that, before we do the handshake, any promotion to Primary
role will either be complete (including the housekeeping stuff), or can
see, and serialize with, the ongoing handshake, based on the
"STATE_SENT" bit, which is set when we start the handshake, and cleared
only when we leave C_WF_REPORT_PARAMS again.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
We need to propagate the configuration into the flag bits,
or it won't be effective.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
Smatch complained about it this redundanct check.
The check was introduced in 2006-09-13. On 2007-07-24 the body of the
function was enclosed by get_ldev()/put_ldev() reference counting.
Since then the check is useless and miss leading.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
If a function has a return value, but its kernel-doc comment doesn't contain a
"Return" section, then emit the following warning:
Warning(file.h:129): No description found for return value of 'fct'
Note: This check emits a lot of warnings at the moment, because many functions
don't have a 'Return' doc section. So until the number of warnings goes
sufficiently down, the check is only performed in verbose mode.
Signed-off-by: Yacine Belkadi <yacine.belkadi.1@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
|
Non-void functions should describe their return values in their kernel-doc
comments. Currently, some don't, others do in various forms. For example:
* Return the result.
* Return: The result.
* Returns the result.
* Returns: the result.
* Return Value: The result.
* @return: the result.
* This function returns the result.
* It will return the result.
Defining a convention would improve consistency of kernel-doc comments. It
would also help scripts/kernel-doc identify the text describing the return
value of a function. Thus allowing additional checks on the comments, and
suitable highlighting in the generated docs (man pages, html, etc).
So, as a convention, use a section named "Return" to describe the return
value of a function.
Signed-off-by: Yacine Belkadi <yacine.belkadi.1@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
|
ret_count has to be at least 3, as we have to count the 2 bytes that are used
for the size of the reply. Without this, memcpy() might be called with zero or
negative count.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The previous memcpy implementation relied on the size advertized by the
device. There were no guarantees that buf was big enough.
Some gymnastic is also required with the +2/-2 to take into account
the first 2 bytes of the returned buffer where the total returned
length is supplied by the device.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
There is no point in keeping the irq in i2c_hid as it's already
there in client.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Simplifies i2c_hid_alloc_buffers tests, and makes this function
responsible of the assignment of ihid->bufsize.
The condition for the reallocation in i2c_hid_start is then simpler.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
HID descriptors contains 4 bytes of reserved field.
The previous implementation was overriding the next fields in struct i2c_hid.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Merely reorganizing documentation. No functional changes. It makes more
sense for the gpio-leds binding to be grouped with other led bindings
than with gpio drivers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
I've legally changed my name with New York State, the US Social Security
Administration, et al. This patch propagates the name change and change
in initials and login to comments in the kernel source as well.
Signed-off-by: Nadia Yvette Chambers <nyc@holomorphy.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The compatible property in device tree "crypto" node has been enhanced
to provide SEC ERA information to the applications.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The test vectors for 'xts(aes)' contain superfluous initializers.
Remove them.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When in fips mode, compression algoritms fails to initialize,
e.g. modprobe ubifs returns
UBIFS error: compr_init: cannot initialize compressor lzo, error -2
FIPS mode should not care about compression algoritms at all.
Patch just set fips_enabled flag to 1 to all compression algorithms
managed by testmgr.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Currently alg_test_null entries set .suite values to zero, which is unneeded.
So perform clean-up of null test entries.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Remove incorrect fips_allowed from camellia null-test entries. Caused by
incorrect copy-paste of aes-aesni null-tests into camellia-aesni null-tests.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
CAST5 and CAST6 both use same lookup tables, which can be moved shared module
'cast_common'.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
For bottom halves off, __this_cpu_read is better.
Signed-off-by: Shan Wei <davidshan@tencent.com>
Reviewed-by: Christoph Lameter <cl@linux.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Provide robustness against low quality FLL sync clocks by increasing the
timeout for lock to an absurdly high point; we should never get anywhere
near hitting the timeout in a real system unless it is failing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Doing so allows the base to be allocated dynamically at runtime and
makes it easier for the chip to coexist with other PWM chips.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
|
|
A single clock is used for all PWMs meaning the clock's reference count
might be between 0 and N when .remove() is called. Instead of a single
clk_disable() call pwm_disable() on each PWM, to ensure that
clk_disable() is called for each PWM that is still enabled.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
|
|
The duty cycles value goes from 1 (99% HIGH) to 256 (0% HIGH) but it
is stored modulo 256 in the register as it is only 8 bits wide.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
|
|
compiling the i.MX pwm driver produces the following warning:
|drivers/pwm/pwm-imx.c: In function 'imx_pwm_probe':
|drivers/pwm/pwm-imx.c:281:7: warning: assignment discards qualifiers from pointer target type
Apply a 'const' attribute to the affected variable declaration.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
|
|
Drivers may want to use this function if they support any of the flags
that can be passed via a third cell in the DT specifier. Since those
drivers may be built as modules the symbol needs to be exported to make
sure that it can be accessed.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
|
|
There are two cases we need to adjust page size in set_spte:
1): the one is other vcpu creates new sp in the window between mapping_level()
and acquiring mmu-lock.
2): the another case is the new sp is created by itself (page-fault path) when
guest uses the target gfn as its page table.
In current code, set_spte drop the spte and emulate the access for these case,
it works not good:
- for the case 1, it may destroy the mapping established by other vcpu, and
do expensive instruction emulation.
- for the case 2, it may emulate the access even if the guest is accessing
the page which not used as page table. There is a example, 0~2M is used as
huge page in guest, in this huge page, only page 3 used as page table, then
guest read/writes on other pages can cause instruction emulation.
Both of these cases can be fixed by allowing guest to retry the access, it
will refault, then we can establish the mapping by using small page
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
|
|
It is $(obj)/oid_registry.o that is dependent on $(obj)/oid_registry_data.c.
The object file cannot be built until $(obj)/oid_registry_data.c has been
generated.
A periodic and hard to reproduce parallel build failure is due to
this incorrect lib/Makefile dependency. The compile error is completely
disingenuous.
GEN lib/oid_registry_data.c
Compiling 49 OIDs
CC lib/oid_registry.o
gcc: error: lib/oid_registry.c: No such file or directory
gcc: fatal error: no input files
compilation terminated.
make[3]: *** [lib/oid_registry.o] Error 4
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Use of_match_ptr and add ifdef CONFIG_OF guard for regulator_gpio_of_match.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
regulator_[get|set]_voltage_sel_regmap
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
[get|set]_voltage_sel
Don't adjust the selector in [get|set]_voltage_sel, fix it in list_voltage() instead.
For smps*(except smps10), the vsel reg-value and voltage mapping as below:
reg-value volt (uV) ( Assume RANGE is x1 )
0 0
1 500000
2 500000
3 500000
4 500000
5 500000
6 500000 (0.49V + 1 * 0.01V) * RANGE
7 510000 (0.49V + 2 * 0.01V) * RANGE
8 520000 (0.49V + 3 * 0.01V) * RANGE
9 530000 (0.49V + 4 * 0.01V) * RANGE
....
The linear mapping is start from selector 6.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Introduce a regulator_can_change_voltage() function for the subsytems or
drivers which might check if applying voltage change is possible and use
special workaround code when the driver is used with fixed regulators or
regulators with disabled ability to change the voltage.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
No point in calculating them every time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://github.com/robclark/kernel-omap4 into drm-next
* 'connector-to-object-prop' of git://github.com/robclark/kernel-omap4:
drm: remove legacy drm_connector_property fxns
drm/nouveau: drm_connector_property -> drm_object_property
drm/i915: One more drm_connector_property -> drm_object_property
drm/i2c: drm_connector_property -> drm_object_property
drm/vmwgfx: drm_connector_property -> drm_object_property
drm/udl: drm_connector_property -> drm_object_property
drm/shmob: drm_connector_property -> drm_object_property
drm/radeon: drm_connector_property -> drm_object_property
drm/gma500: drm_connector_property -> drm_object_property
|
|
net/core/neighbour.c:65:12: warning: 'zero' defined but not used [-Wunused-variable]
net/core/neighbour.c:66:12: warning: 'unres_qlen_max' defined but not used [-Wunused-variable]
These variables are only used when CONFIG_SYSCTL is defined,
so move them under #ifdef CONFIG_SYSCTL.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since GCC 4.4, there have been __builtin_bswap32() and __builtin_bswap16()
intrinsics. A __builtin_bswap16() came a little later (4.6 for PowerPC,
48 for other platforms).
By using these instead of the inline assembler that most architectures
have in their __arch_swabXX() macros, we let the compiler see what's
actually happening. The resulting code should be at least as good, and
much *better* in the cases where it can be combined with a nearby load
or store, using a load-and-byteswap or store-and-byteswap instruction
(e.g. lwbrx/stwbrx on PowerPC, movbe on Atom).
When GCC is sufficiently recent *and* the architecture opts in to using
the intrinsics by setting CONFIG_ARCH_USE_BUILTIN_BSWAP, they will be
used in preference to the __arch_swabXX() macros. An architecture which
does not set ARCH_USE_BUILTIN_BSWAP will continue to use its own
hand-crafted macros.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Implement ONE_REG interface for EPCR register adding KVM_REG_PPC_EPCR to
the list of ONE_REG PPC supported registers.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: remove HV dependency, use get/put_user]
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Add EPCR support in booke mtspr/mfspr emulation. EPCR register is defined only
for 64-bit and HV categories, we will expose it at this point only to 64-bit
virtual processors running on 64-bit HV hosts.
Define a reusable setter function for vcpu's EPCR.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: move HV dependency in the code]
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
When delivering guest IRQs, update MSR computation mode according to guest
interrupt computation mode found in EPCR.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: remove HV dependency in the code]
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
In BookE, EPCR is defined and valid when either the HV or the 64bit
category are implemented. Reflect this in the field definition.
Today the only KVM target on 64bit is HV enabled, so there is no
change in actual source code, but this keeps the code closer to the
spec and doesn't build up artificial road blocks for a PR KVM
on 64bit.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Extend MAS2 EPN mask to retain most significant bits on 64-bit hosts.
Use this mask in tlb effective address accessor.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Mask high 32 bits of MAS2's effective page number in tlbwe emulation for guests
running in 32-bit mode.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Mask high 32 bits of effective address in emulation layer for guests running
in 32-bit mode.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: fix indent]
Signed-off-by: Alexander Graf <agraf@suse.de>
|
