| Age | Commit message (Collapse) | Author |
|---|
|
Fix the following build errors:
CC arch/sh/kernel/cpu/sh4a/setup-sh7757.o
arch/sh/kernel/cpu/sh4a/setup-sh7757.c:681: error: implicit declaration of function ‘DMA_BIT_MASK’
arch/sh/kernel/cpu/sh4a/setup-sh7757.c:681: error: initializer element is not constant
arch/sh/kernel/cpu/sh4a/setup-sh7757.c:681: error: (near initialization for ‘usb_ehci_device.dev.coherent_dma_mask’)
arch/sh/kernel/cpu/sh4a/setup-sh7757.c:705: error: initializer element is not constant
arch/sh/kernel/cpu/sh4a/setup-sh7757.c:705: error: (near initialization for ‘usb_ohci_device.dev.coherent_dma_mask’)
make[3]: *** [arch/sh/kernel/cpu/sh4a/setup-sh7757.o] Error 1
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
sh-sci.c sets hardware up and then let the HW do all flow controls.
There is no software code, nor needs to get/set real CTS signal.
But, when turning CRTSCTS on through termios, uart_set_termios() in
serial_core.c checks CTS, and stops TX if it is inactive at the moment.
Because sci_get_mctrl() returns a fixed value DTR|RTS|DSR but CTS,
the sequence
open -> set CRTSCTS -> write
hit the case and stop working, no more outputs.
This patch makes sci_get_mctrl() report CTS in addition.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This adds unaligned memory access support for the following instructions:
mov.w @(disp,PC),Rn
mov.l @(disp,PC),Rn
These instructions are often used on SH2A toolchains.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch just clears the return code for those cases where an
unaligned memory access occurs on branch instructions without a
delay slot.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
The iscsi_nopout task's TTT is defined as __be32 while the DMA
memory to the chip is CPU specific. This creates a problem for
unsolicited NOP-In responses where the TTT is not the RESERVED
tag of 0xFFs. This patch adds a call to be32_to_cpu for the TTT
specified.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
In commit 6a716a8, while releasing the DDP context in case frame_send() failed,
the frame may already be freed, so we should store the pointer to fc_fcp_pkt and
release the DDP context using the locally stored fsp instead of getting fsp from
the fr_fsp(fp) on a frame.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Reported-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Call fc_block_scsi_eh() in all fcoe eh to blocks
the scsi_eh thread for blocked rports.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Current fc_eh_host_reset leaves lport offline
permanently due to FLOGI response getting
handled by LOGO response from last reset as both
had same exchange id.
So fix this by having end to end exches clean-up
using exchange abort along exches reset
done from fc_eh_host_reset. This would avoid
exchanges collision between the sessions across
the reset. In this case implicit login should have
done that but no aborting support for FIP
frames, so just wait till lport->r_a_tov before
restarting next flogi to ensure all exchanges
are good to use again for next session.
Below is the trace of LOGO from older session
coming ahead of FLOGI response with same exche id
0x203:-
617 86.435165 4e.00.0b -> ff.ff.fc FC ELS LOGO 0x203
618 86.435195 4e.00.0b -> b6.02.00 FC ELS LOGO 0x213
619 86.435220 4e.00.0b -> 18.03.00 FC ELS LOGO 0x223
620 86.435244 4e.00.0b -> 18.02.00 FC ELS LOGO 0x233
621 86.435267 4e.00.0b -> 18.01.00 FC ELS LOGO 0x243
622 86.435349 00.00.00 -> ff.ff.fe FC ELS FLOGI 0x203
623 86.435549 ff.ff.fc -> 4e.00.0b FC ELS ACC (LOGO) 0x203
624 86.438721 ff.ff.fe -> 4e.00.0b FC ELS ACC (FLOGI) 0x203
625 86.442059 18.03.00 -> 4e.00.0b FC ELS ACC (LOGO) 0x223
626 86.443683 b6.02.00 -> 4e.00.0b FC ELS ACC (LOGO) 0x213
627 86.447693 18.01.00 -> 4e.00.0b FC ELS ACC (LOGO) 0x243
628 86.453499 18.02.00 -> 4e.00.0b FC ELS ACC (LOGO) 0x233
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The rtnl cannot be held durrng the fcoe_interface_put.
If it is the last reference on the fcoe_interface the
fcoe_ctlr_destroy will be called as a part of the
cleanup, ultimately calling cancel_work_sync(&fip->recv_work);
If we are processing a flogi response we will be in
the recv_work context and we will lock the rtnl to
add a new unicast MAC address. This is how the deadlock
can occur.
The fix is simply to move the rtnl_lock/unlock into
fcoe_interface_cleanup so that it can be unlocked before
fcoe_interface_put is called.
Here is the lockdep report:
Jul 21 11:26:35 bubba [ 223.870702]
ul 21 11:26:35 bubba [ 223.870704] =======================================================
Jul 21 11:26:35 bubba [ 223.871255] [ INFO: possible circular locking dependency detected ]
Jul 21 11:26:35 bubba [ 223.871530] 3.0.0-rc7+ #1
Jul 21 11:26:35 bubba [ 223.871797] -------------------------------------------------------
Jul 21 11:26:35 bubba [ 223.872072] lockdeptest.sh/3464 is trying to acquire lock:
Jul 21 11:26:35 bubba [ 223.872345] ((&fip->recv_work)
Jul 21 11:26:35 bubba ){+.+.+.}
Jul 21 11:26:35 bubba , at:
Jul 21 11:26:35 bubba [<ffffffff810531f1>] wait_on_work+0x0/0xbd
Jul 21 11:26:35 bubba [ 223.873022]
Jul 21 11:26:35 bubba [ 223.873023] but task is already holding lock:
Jul 21 11:26:35 bubba [ 223.873555] (rtnl_mutex
Jul 21 11:26:35 bubba ){+.+.+.}
Jul 21 11:26:35 bubba , at:
Jul 21 11:26:35 bubba [<ffffffff813e8233>] rtnl_lock+0x12/0x14
Jul 21 11:26:35 bubba [ 223.874229]
Jul 21 11:26:35 bubba [ 223.874230] which lock already depends on the new lock.
Jul 21 11:26:35 bubba [ 223.874231]
Jul 21 11:26:35 bubba [ 223.875032]
Jul 21 11:26:35 bubba [ 223.875033] the existing dependency chain (in reverse order) is:
Jul 21 11:26:35 bubba [ 223.875573]
Jul 21 11:26:35 bubba [ 223.875573] -> #1
Jul 21 11:26:35 bubba (rtnl_mutex
Jul 21 11:26:35 bubba ){+.+.+.}
Jul 21 11:26:35 bubba :
Jul 21 11:26:35 bubba [ 223.876301]
Jul 21 11:26:35 bubba [<ffffffff8106c14a>] lock_acquire+0xd2/0xf7
Jul 21 11:26:35 bubba [ 223.876645]
Jul 21 11:26:35 bubba [<ffffffff8151d975>] __mutex_lock_common+0x47/0x30d
Jul 21 11:26:35 bubba [ 223.876991]
Jul 21 11:26:35 bubba [<ffffffff8151dd36>] mutex_lock_nested+0x3b/0x40
Jul 21 11:26:35 bubba [ 223.877334]
Jul 21 11:26:35 bubba [<ffffffff813e8233>] rtnl_lock+0x12/0x14
Jul 21 11:26:35 bubba [ 223.877675]
Jul 21 11:26:35 bubba [<ffffffffa003d5a0>] fcoe_update_src_mac+0x2b/0x80 [fcoe]
Jul 21 11:26:35 bubba [ 223.878022]
Jul 21 11:26:35 bubba [<ffffffffa003d698>] fcoe_flogi_resp+0x5e/0x79 [fcoe]
Jul 21 11:26:35 bubba [ 223.878366]
Jul 21 11:26:35 bubba [<ffffffffa001566f>] fc_exch_recv+0x7f5/0x9da [libfc]
Jul 21 11:26:35 bubba [ 223.878713]
Jul 21 11:26:35 bubba [<ffffffffa00327d8>] fcoe_ctlr_recv_work+0x71f/0x10dc [libfcoe]
Jul 21 11:26:35 bubba [ 223.879258]
Jul 21 11:26:35 bubba [<ffffffff81053761>] process_one_work+0x1d7/0x347
Jul 21 11:26:35 bubba [ 223.879601]
Jul 21 11:26:35 bubba [<ffffffff81054ade>] worker_thread+0xf8/0x17c
Jul 21 11:26:35 bubba [ 223.879944]
Jul 21 11:26:35 bubba [<ffffffff81058184>] kthread+0x7d/0x85
Jul 21 11:26:35 bubba [ 223.880287]
Jul 21 11:26:35 bubba [<ffffffff81526414>] kernel_thread_helper+0x4/0x10
Jul 21 11:26:35 bubba [ 223.880634]
Jul 21 11:26:35 bubba [ 223.880635] -> #0
Jul 21 11:26:35 bubba ((&fip->recv_work)
Jul 21 11:26:35 bubba ){+.+.+.}
Jul 21 11:26:35 bubba :
Jul 21 11:26:35 bubba [ 223.881357]
Jul 21 11:26:35 bubba [<ffffffff8106b93e>] __lock_acquire+0xb1d/0xe2c
Jul 21 11:26:35 bubba [ 223.881695]
Jul 21 11:26:35 bubba [<ffffffff8106c14a>] lock_acquire+0xd2/0xf7
Jul 21 11:26:35 bubba [ 223.882033]
Jul 21 11:26:35 bubba [<ffffffff81053241>] wait_on_work+0x50/0xbd
Jul 21 11:26:35 bubba [ 223.882378]
Jul 21 11:26:35 bubba [<ffffffff81053b32>] __cancel_work_timer+0xb6/0xf4
Jul 21 11:26:35 bubba [ 223.882718]
Jul 21 11:26:35 bubba [<ffffffff81053b8a>] cancel_work_sync+0xb/0xd
Jul 21 11:26:35 bubba [ 223.883057]
Jul 21 11:26:35 bubba [<ffffffffa00317e6>] fcoe_ctlr_destroy+0x1d/0x67 [libfcoe]
Jul 21 11:26:35 bubba [ 223.883399]
Jul 21 11:26:35 bubba [<ffffffffa003e51e>] fcoe_interface_release+0x21/0x45 [fcoe]
Jul 21 11:26:35 bubba [ 223.883940]
Jul 21 11:26:35 bubba [<ffffffff811fbbe6>] kref_put+0x43/0x4d
Jul 21 11:26:35 bubba [ 223.884280]
Jul 21 11:26:35 bubba [<ffffffffa003ebba>] fcoe_interface_put+0x17/0x19 [fcoe]
Jul 21 11:26:35 bubba [ 223.884624]
Jul 21 11:26:35 bubba [<ffffffffa003f2a6>] fcoe_interface_cleanup+0x188/0x193 [fcoe]
Jul 21 11:26:35 bubba [ 223.885163]
Jul 21 11:26:35 bubba [<ffffffffa003f303>] fcoe_destroy+0x52/0x72 [fcoe]
Jul 21 11:26:35 bubba [ 223.885502]
Jul 21 11:26:35 bubba [<ffffffffa00340a4>] fcoe_transport_destroy+0xab/0x110 [libfcoe]
Jul 21 11:26:35 bubba [ 223.886045]
Jul 21 11:26:35 bubba [<ffffffff81056153>] param_attr_store+0x43/0x62
Jul 21 11:26:35 bubba [ 223.886385]
Jul 21 11:26:35 bubba [<ffffffff8105602d>] module_attr_store+0x21/0x25
Jul 21 11:26:35 bubba [ 223.886728]
Jul 21 11:26:35 bubba [<ffffffff8114c23d>] sysfs_write_file+0x103/0x13f
Jul 21 11:26:35 bubba [ 223.887068]
Jul 21 11:26:35 bubba [<ffffffff810f3e7b>] vfs_write+0xa7/0xfa
Jul 21 11:26:35 bubba [ 223.887406]
Jul 21 11:26:35 bubba [<ffffffff810f4073>] sys_write+0x45/0x69
Jul 21 11:26:35 bubba [ 223.887742]
Jul 21 11:26:35 bubba [<ffffffff815252bb>] system_call_fastpath+0x16/0x1b
Jul 21 11:26:35 bubba [ 223.888083]
Jul 21 11:26:35 bubba [ 223.888084] other info that might help us debug this:
Jul 21 11:26:35 bubba [ 223.888085]
Jul 21 11:26:35 bubba [ 223.888879] Possible unsafe locking scenario:
Jul 21 11:26:35 bubba [ 223.888881]
Jul 21 11:26:35 bubba [ 223.889411] CPU0 CPU1
Jul 21 11:26:35 bubba [ 223.889683] ---- ----
Jul 21 11:26:35 bubba [ 223.889955] lock(
Jul 21 11:26:35 bubba rtnl_mutex
Jul 21 11:26:35 bubba );
Jul 21 11:26:35 bubba [ 223.890349] lock(
Jul 21 11:26:35 bubba (&fip->recv_work)
Jul 21 11:26:35 bubba );
Jul 21 11:26:35 bubba [ 223.890751] lock(
Jul 21 11:26:35 bubba rtnl_mutex
Jul 21 11:26:35 bubba );
Jul 21 11:26:35 bubba [ 223.891154] lock(
Jul 21 11:26:35 bubba (&fip->recv_work)
Jul 21 11:26:35 bubba );
Jul 21 11:26:35 bubba [ 223.891549]
Jul 21 11:26:35 bubba [ 223.891550] *** DEADLOCK ***
Jul 21 11:26:35 bubba [ 223.891551]
Jul 21 11:26:35 bubba [ 223.892347] 6 locks held by lockdeptest.sh/3464:
Jul 21 11:26:35 bubba [ 223.892621] #0:
Jul 21 11:26:35 bubba (&buffer->mutex
Jul 21 11:26:35 bubba ){+.+.+.}
Jul 21 11:26:35 bubba , at:
Jul 21 11:26:35 bubba [<ffffffff8114c171>] sysfs_write_file+0x37/0x13f
Jul 21 11:26:35 bubba [ 223.893359] #1:
Jul 21 11:26:35 bubba (s_active
Jul 21 11:26:35 bubba ){++++.+}
Jul 21 11:26:35 bubba , at:
Jul 21 11:26:35 bubba [<ffffffff8114c21c>] sysfs_write_file+0xe2/0x13f
Jul 21 11:26:35 bubba [ 223.894094] #2:
Jul 21 11:26:35 bubba (param_lock
Jul 21 11:26:35 bubba ){+.+.+.}
Jul 21 11:26:35 bubba , at:
Jul 21 11:26:35 bubba [<ffffffff81056146>] param_attr_store+0x36/0x62
Jul 21 11:26:35 bubba [ 223.894835] #3:
Jul 21 11:26:35 bubba (ft_mutex
Jul 21 11:26:35 bubba ){+.+.+.}
Jul 21 11:26:35 bubba , at:
Jul 21 11:26:35 bubba [<ffffffffa0034017>] fcoe_transport_destroy+0x1e/0x110 [libfcoe]
Jul 21 11:26:35 bubba [ 223.895574] #4:
Jul 21 11:26:35 bubba (fcoe_config_mutex
Jul 21 11:26:35 bubba ){+.+.+.}
Jul 21 11:26:35 bubba , at:
Jul 21 11:26:35 bubba [<ffffffffa003f2c9>] fcoe_destroy+0x18/0x72 [fcoe]
Jul 21 11:26:35 bubba [ 223.896314] #5:
Jul 21 11:26:35 bubba (rtnl_mutex
Jul 21 11:26:35 bubba ){+.+.+.}
Jul 21 11:26:35 bubba , at:
Jul 21 11:26:35 bubba [<ffffffff813e8233>] rtnl_lock+0x12/0x14
Jul 21 11:26:35 bubba [ 223.897047]
Jul 21 11:26:35 bubba [ 223.897048] stack backtrace:
Jul 21 11:26:35 bubba [ 223.897578] Pid: 3464, comm: lockdeptest.sh Not tainted 3.0.0-rc7+ #1
Jul 21 11:26:35 bubba [ 223.897853] Call Trace:
Jul 21 11:26:35 bubba [ 223.898128] [<ffffffff81068e16>] print_circular_bug+0x1f8/0x209
Jul 21 11:26:35 bubba [ 223.898416] [<ffffffff8106b93e>] __lock_acquire+0xb1d/0xe2c
Jul 21 11:26:35 bubba [ 223.898699] [<ffffffff810531f1>] ? wait_on_cpu_work+0xe6/0xe6
Jul 21 11:26:35 bubba [ 223.898982] [<ffffffff8106c14a>] lock_acquire+0xd2/0xf7
Jul 21 11:26:35 bubba [ 223.899263] [<ffffffff810531f1>] ? wait_on_cpu_work+0xe6/0xe6
Jul 21 11:26:35 bubba [ 223.899547] [<ffffffff8104a097>] ? mod_timer+0x8f/0x98
Jul 21 11:26:35 bubba [ 223.899827] [<ffffffff81053241>] wait_on_work+0x50/0xbd
Jul 21 11:26:35 bubba [ 223.900108] [<ffffffff810531f1>] ? wait_on_cpu_work+0xe6/0xe6
Jul 21 11:26:35 bubba [ 223.900390] [<ffffffff81053b32>] __cancel_work_timer+0xb6/0xf4
Jul 21 11:26:35 bubba [ 223.900671] [<ffffffff81053b8a>] cancel_work_sync+0xb/0xd
Jul 21 11:26:35 bubba [ 223.900953] [<ffffffffa00317e6>] fcoe_ctlr_destroy+0x1d/0x67 [libfcoe]
Jul 21 11:26:35 bubba [ 223.901237] [<ffffffffa003e51e>] fcoe_interface_release+0x21/0x45 [fcoe]
Jul 21 11:26:35 bubba [ 223.901522] [<ffffffffa003e4fd>] ? fcoe_enable+0x6b/0x6b [fcoe]
Jul 21 11:26:35 bubba [ 223.901803] [<ffffffff811fbbe6>] kref_put+0x43/0x4d
Jul 21 11:26:35 bubba [ 223.902083] [<ffffffffa003ebba>] fcoe_interface_put+0x17/0x19 [fcoe]
Jul 21 11:26:35 bubba [ 223.902367] [<ffffffffa003f2a6>] fcoe_interface_cleanup+0x188/0x193 [fcoe]
Jul 21 11:26:35 bubba [ 223.902653] [<ffffffff8151dd36>] ? mutex_lock_nested+0x3b/0x40
Jul 21 11:26:35 bubba [ 223.902939] [<ffffffffa003f303>] fcoe_destroy+0x52/0x72 [fcoe]
Jul 21 11:26:35 bubba [ 223.903223] [<ffffffffa00340a4>] fcoe_transport_destroy+0xab/0x110 [libfcoe]
Jul 21 11:26:35 bubba [ 223.903508] [<ffffffff81056153>] param_attr_store+0x43/0x62
Jul 21 11:26:35 bubba [ 223.903792] [<ffffffff8105602d>] module_attr_store+0x21/0x25
Jul 21 11:26:35 bubba [ 223.904075] [<ffffffff8114c23d>] sysfs_write_file+0x103/0x13f
Jul 21 11:26:35 bubba [ 223.904357] [<ffffffff810f3e7b>] vfs_write+0xa7/0xfa
Jul 21 11:26:35 bubba [ 223.904642] [<ffffffff810f51d6>] ? fget_light+0x35/0x96
Jul 21 11:26:35 bubba [ 223.904923] [<ffffffff810f4073>] sys_write+0x45/0x69
Jul 21 11:26:35 bubba [ 223.905204] [<ffffffff815252bb>] system_call_fastpath+0x16/0x1b
Jul 21 11:26:36 bubba [ 223.964438] ixgbe 0000:05:00.0: eth3: detected SFP+: 5
Jul 21 11:26:37 bubba [ 225.196702] ixgbe 0000:05:00.0: eth3: NIC Link is Up 10 Gbps, Flow Control: None
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
There are the following warnings and errorx when compiling the driver.
The patch adds the missing inclusion of linux/module.h to fix them.
drivers/mmc/host/sdhci-esdhc-imx.c:563:12: error: ‘THIS_MODULE’ undeclared here (not in a function)
[..]
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ARM: mach-shmobile: sh7372 LCDC1 suspend fix V2 (incremental)
OMAP: omap_device: only override _noirq methods, not normal suspend/resume
PM / Runtime: Correct documentation of pm_runtime_irq_safe()
ARM: mach-shmobile: sh7372 LCDC1 suspend fix
sh-sci / PM: Use power.irq_safe
PM: Use spinlock instead of mutex in clock management functions
|
|
For ARMv7 kernels running in the non-secure world, writing to the
auxillary control register causes an abort, so we must avoid directly
writing the auxillary control register. If the ACR has already been
reinitialized by SoC code, don't try to restore it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add a dsb after the isb to ensure that the previous writes to the
CP15 registers take effect before we enable the MMU.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
ARM920 and ARM926 save four registers, not three. Fix the size of
the suspend region required.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
r1 stores the v:p offset from the CPU invariant resume code, and is
expected to be preserved by the CPU specific code. Overwriting it is
not a good idea.
We've managed to get away with it on sa1100 platforms because most
happen to have PHYS_OFFSET == PAGE_OFFSET, but that may not be the
case depending on kernel configuration. So fix this latent bug.
This fixes xsc3 as well which was saving and restoring this register
independently.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
cpu_v7_reset disables the MMU and then branches to the provided address.
On Thumb-2 kernels, we should take care to clear the Thumb Exception
enable bit in the System Control Register, otherwise this may wreak
havok in the code to which we are branching (for example, an ARM kernel
image via kexec).
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit 540b5738 ("ARM: 6999/1: head, zImage: Always Enter the kernel in
ARM state") mandates that the kernel should be entered in ARM state.
If a Thumb-2 kernel kexecs a new kernel image, we need to ensure that
we change state when branching to the new code. This patch replaces a
mov pc, lr with a bx lr on Thumb-2 kernels so that we transition to ARM
state if need be.
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: sbp2: fix panic after rmmod with slow targets
|
|
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The memset of the fcp_cmnd struct needs to be moved so that it will not
zero-out valid data.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
port-update handling.
Transitioning to a LOOP_UPDATE loop-state could cause the driver
to miss normal link/target processing. LOOP_UPDATE is a crufty
artifact leftover from at time the driver performed it's own
internal command-queuing. Safely remove this state.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
fails.
Close a small window where we could falsely fail an abort request if the mailbox
command fails but the command was returned during interrupt context.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The dsd list shouldn't be manipulated without taking the per host hardware
lock to prevent multiple callers from trampling upon one another.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Since we enable interrupts before initializing the firmware, use the chip
revision from PCI config space directly to perform the chip revision check.
Also remove the unnecessary firmware attributes test.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This fix:
- Disables app tag peeking; correct tag check will be added when the
SCSI API is available.
- Always derive ref_tag from scsi_get_lba()
- Removes incorrect swap of FCP_LUN in FCP_CMND
- Moves app-tag error check before ref-tag check. The reason being,
currently there is no interface in SCSI to retrieve the app-tag
for protection I/Os, so driver puts zero for app-tag in the
firmware interface, but requests not to validate it, but when a
ref-tag error is detected by firmware, it would put
expected/actual tags for all the protection tags (guard/app/ref).
As driver checks for app tag error first, a ref-tag error is
incorrectly flagged as app-tag error.
- Convert HBA specific checks to capability based.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Driver needs to update protection bytes for uninitialized sectors as they are
not DMA-d.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Reviewed-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch updates the recently submitted
"Associate the HDMI clock together with LCDC1 on sh7372"
to V2 with the following change:
- Use lcdc1_device on AP4EVB to build properly.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
The slab has just one free object, adding it to partial list head doesn't make
sense. And it can cause lock contentation. For example,
1. CPU takes the slab from partial list
2. fetch an object
3. switch to another slab
4. free an object, then the slab is added to partial list again
In this way n->list_lock will be heavily contended.
In fact, Alex had a hackbench regression. 3.1-rc1 performance drops about 70%
against 3.0. This patch fixes it.
Acked-by: Christoph Lameter <cl@linux.com>
Reported-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Shaohua Li <shli@kernel.org>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
|
|
For i2c drivers, we should use "i2c:" prefix for modalias.
MODULE_DEVICE_TABLE will setup the modulalias for us, thus adding
a MODULE_ALIAS is redundant (in addition to being incorrect).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
If successful, usb_control_msg returns the number of bytes transferred,
otherwise a negative error number.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The Wacom PenPartner should advertise its stylus tip and button
in addition to the eraser tool. These are both physically
present on the hardware, and emitted from 'wacom_penpartner_irq'.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Touch devices do not report valid pressure or capacitance.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Only register as an RTC device after the hardware has been
successfully initialized. The RTC class driver will call
back to this driver to read a pending alarm, and other
drivers watching for new devices on the RTC class may
read the RTC time upon registration. Such access might
occur while the RTC is stopped, prior to clearing
pending alarms, etc.
The new ordering also avoids leaving the platform
device drvdata set to an unregistered struct rtc_device *
on probe errors.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Even though the Linux kernel does not use the tm_isdst field, it is
exposed as part of the ABI. This field can accidentally be left
initialized, which is why we currently memset buffers returned to
userland in rtc_read_time.
There is a case however where the field can return garbage from the
stack though when using the RTC_ALM_READ ioctl on the rtc device. This
ioctl invokes rtc_read_alarm, which is careful to memset the rtc_wkalrm
buffer that is copied to userland, but it then uses a struct copy to
assign to alarm->time given the return value from rtc_ktime_to_tm().
rtc_ktime_to_tm() is implemented by calling rtc_time_to_tm using a
derivative seconds counds from ktime, but rtc_time_to_tm does not assign
a value to ->tm_isdst. This results in garbage from rtc_ktime_to_tm()'s
frame ending up being copied out to userland as part of the returned
rtc_wkalrm.
Fix this by initializing rtc_time->tm_isdst to 0 in rtc_time_to_tm.
Signed-off-by: Mike Waychison <mikew@google.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
The nfsservctl system call is now gone, so we should remove all
linkage for it.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915: Fix wrong initializer for "locked" variable in assert_panel_unlocked
i915: do not setup intel_backlight twice
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits)
USB: ftdi_sio: add Calao reference board support
USB option driver K3765/K4505 avoid CDC_DATA interface
USB: option: add YUGA device id to driver
usb: s5p-ehci: fix a NULL pointer deference
USB: EHCI: Do not rely on PORT_SUSPEND to stop USB resuming in ehci_bus_resume().
USB option driver add PID of Huawei Vodafone K4605
USB option driver add PID of Huawei Vodafone K3806
xhci: Handle zero-length isochronous packets.
USB: Avoid NULL pointer deref in usb_hcd_alloc_bandwidth.
usb: musb: gadget: fix error path
usb: gadget: f_phonet: unlock in error case
usb: musb: blackfin: include prefetch head file
usb: musb: tusb6010: fix compilation
usb: gadget: renesas_usbhs: fix DMA build by including dma-mapping.h
usb: musb: cppi: fix build errors due to DBG and missing musb variable
usb: musb: ux500: replace missing DBG with dev_dbg
usb: musb: ux500: set dma config for both src and dst
usb: musb: fix oops on musb_gadget_pullup
usb: host: ehci-omap: fix .remove and failure handling path of .probe(v1)
usb: gadget: hid: don't STALL when processing a HID Descriptor request
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
omap-serial: Allow IXON and IXOFF to be disabled.
TTY: serial, document ignoring of uart->ops->startup error
TTY: pty, fix pty counting
8250: Fix race condition in serial8250_backup_timeout().
serial/8250_pci: delete duplicate data definition
8250_pci: add support for Rosewill RC-305 4x serial port card
tty: Add "spi:" prefix for spi modalias
atmel_serial: fix atmel_default_console_device
serial: 8250_pnp: add Intermec CV60 touchscreen device
drivers/serial/ucc_uart.c: Fix compiler warning
pch_uart: Set PCIe bus number using probe parameter
serial: samsung: Fix build error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6
* 'driver-core-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
drivers:misc: ti-st: fix unexpected UART close
drivers:misc: ti-st: free skb on firmware download
drivers:misc: ti-st: wait for completion at fail
drivers:misc: ti-st: reinit completion before send
drivers:misc: ti-st: fail-safe on wrong pkt type
drivers:misc: ti-st: reinit completion on ver read
drivers:misc:ti-st: platform hooks for chip states
drivers:misc: ti-st: avoid a misleading dbg msg
base/devres.c: quiet sparse noise about context imbalance
pti: add missing CONFIG_PCI dependency
drivers/base/devtmpfs.c: correct annotation of `setup_done'
driver core: fix kernel-doc warning in platform.c
firmware: fix google/gsmi.c build warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
staging: tidspbridge: fix compilation on dsp clock functions
staging: octeon-ethernet: Add missing #includes.
Staging: zcache: signedness bug in tmem_get()
staging: zcache: fix crash on high memory swap
staging: brcm80211: SPARC build error fix
staging: brcm80211: fix compile error on non-x86 archs since 3.0 kernel
|
|
If a physical device exposed to the OS by hpsa
is replaced (e.g. one hot plug tape drive is replaced
by another, or a tape drive is placed into "OBDR" mode
in which it acts like a CD-ROM device) and a rescan is
initiated, the replaced device will be added to the
SCSI midlayer with target and lun numbers set to -1.
After that, a panic is likely to ensue. When a physical
device is replaced, the lun and target number should be
preserved.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The test to detect OBDR ("One Button Disaster Recovery")
cd-rom devices was comparing against uninitialized data.
Fixed by moving the test for the device to where the
inquiry data is collected, and uninitialized variable
altogether as it wasn't really being used.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
__netpoll_rx() doesnt properly handle skbs with small header
pskb_may_pull() or pskb_trim_rcsum() can change skb->data, we must
reload it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Spotted-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ti_hecc_probe(), the spinlock priv->mbx_lock is not
inited, causing a spinlock lockup BUG.
Acked-by: Anant Gole <anantgole@ti.com>
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ti_hecc_xmit(), local variable "data" is not initialized before
being used.
This initialization got inadvertently removed in the following patch:
can: Unify droping of invalid tx skbs and netdev stats
Acked-by: Anant Gole <anantgole@ti.com>
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following build error:
CC drivers/net/sh_eth.o
drivers/net/sh_eth.c:1115: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘sh_eth_interrupt’
drivers/net/sh_eth.c: In function ‘sh_eth_open’:
drivers/net/sh_eth.c:1387: error: implicit declaration of function ‘request_irq’
drivers/net/sh_eth.c:1387: error: ‘sh_eth_interrupt’ undeclared (first use in this function)
drivers/net/sh_eth.c:1387: error: (Each undeclared identifier is reported only once
drivers/net/sh_eth.c:1387: error: for each function it appears in.)
drivers/net/sh_eth.c:1391: error: ‘IRQF_SHARED’ undeclared (first use in this function)
drivers/net/sh_eth.c:1424: error: implicit declaration of function ‘free_irq’
make[2]: *** [drivers/net/sh_eth.o] Error 1
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the DP83865 datasheet we need to clear
the interrupt status bit by writing a 1 to the
corresponding bit in INT_CLEAR (2:0 are reserved).
Proposed and tested by Thorsten.
Signed-off-by: Thorsten Schubert <tshu@msc-ge.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
