| Age | Commit message (Collapse) | Author |
|---|
|
After commit 028af5941dd8 ("mfd: intel-lpss: Pass SDA hold time to
I2C host controller driver") the driver still has a non-used variable.
Remove it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is a sucky change to bump up the time we'll wait for the EC. Why
is it sucky? If 200ms for a transfer is a common thing it will have a
massively bad impact on keyboard responsiveness.
It still seems like a good idea to do this, though, because we have a
gas gauge that claims that in an extreme case it could stretch the i2c
clock for 144ms. It's not a common case so it shouldn't affect
responsiveness, but it can happen. It's much better to have a single
slow keyboard response than to start returning errors when we don't
have to.
In newer EC designs we should probably implement a virtual battery to
respond to the kernel to insulate the kernel from these types of
issues.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
TI LMU (Lighting Management Unit) driver supports lighting devices below.
LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.
LMU devices have common features.
- I2C interface for accessing device registers
- Hardware enable pin control
- Backlight brightness control
- Notifier for hardware fault monitoring
- Regulators for LCD display bias
It contains fault monitor, backlight, LED and regulator driver.
LMU fault monitor
-----------------
LM3633 and LM3697 provide hardware monitoring feature.
It enables open or short circuit detection.
After monitoring is done, each device should be re-initialized.
Notifier is used for this case.
Separate patch for 'ti-lmu-fault-monitor' will be sent later.
Backlight
---------
It's handled by TI LMU backlight consolidated driver and
chip dependent data. Separate patchset will be sent later.
LED indicator
-------------
LM3633 has 6 indicator LEDs. Programmable dimming pattern is also
supported. Separate patch for 'leds-lm3633' will be sent later.
Regulator
---------
LM3631 has 5 regulators for the display bias.
LM3632 supports 3 regulators. One consolidated driver enables it.
The lm363x regulator driver is already upstreamed.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch describes overall binding for TI LMU MFD devices.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
commit b101829a029a ("mfd: axp20x: Fix AXP806 access errors on cold boot")
was intended to fix the case where a board uses an AXP806 in slave mode,
but the boot loader leaves it in master mode for lack of AXP806 support.
But now the driver breaks on boards where the PMIC is operating in master
mode. This patch lets the driver use the new device tree property
"xpowers,master-mode" to set the correct operating mode for the board.
Fixes: 8824ee857348 ("mfd: axp20x: Add support for AXP806 PMIC")
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
commit b101829a029a ("mfd: axp20x: Fix AXP806 access errors on cold boot")
was intended to fix the case where a board uses an AXP806 in slave mode,
but the boot loader leaves it in master mode for lack of AXP806 support.
But now the driver breaks on boards where the PMIC is operating in master
mode. To let the device tree describe which mode of operation is needed,
this patch introduces a new property "xpowers,master-mode".
Fixes: 204ae2963e10 ("mfd: axp20x: Add bindings for AXP806 PMIC")
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Since commit 845c877009cf ("i2c / ACPI: Assign IRQ for devices that have
GpioInt automatically") I2C core assigns interrupt line to I2C slave
devices with regarding to GpioInt() resources.
There is no need to repeat this in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
STM32 timers register bank size is 0x400. Fix regmap max_register.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
It is a debugging statement so make it be issued only then.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
At least two different omap3630/3730 boards booting from MMC1
fail to reboot if the "ti,twl4030-power-idle-osc-off" or
"ti,twl4030-power-idle" compatible flags are set. This patch will
keep the vmmc1 powered up during reboot allowing the bootloader
to load.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add missing of_platform_depopulate() upon driver removal.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patches adds the first minimal support to the upstream Linux tree.
Signed-off-by: Priyalee Kushwaha <priyalee.kushwaha@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch installs an ACPI GPE handler for LID0 ACPI device to indicate
ACPI core that this GPE should stay enabled for lid to work in suspend
to idle path.
Signed-off-by: Archana Patni <archana.patni@intel.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
'ib-mfd-input-4.12', 'ib-mfd-leds-4.12', 'ib-mfd-phy-4.12' and 'ib-mfd-pinctrl-samsung-4.12' into ibs-for-mfd-merged
|
|
The introduced namespace support moved the BCM variables for procfs into a
per-net data structure. This leads to a build failure with disabled procfs:
on x86_64:
when CONFIG_PROC_FS is not enabled:
../net/can/bcm.c:1541:14: error: 'struct netns_can' has no member named 'bcmproc_dir'
../net/can/bcm.c:1601:14: error: 'struct netns_can' has no member named 'bcmproc_dir'
../net/can/bcm.c:1696:11: error: 'struct netns_can' has no member named 'bcmproc_dir'
../net/can/bcm.c:1707:15: error: 'struct netns_can' has no member named 'bcmproc_dir'
http://marc.info/?l=linux-can&m=149321842526524&w=2
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
irq_time_read() returns the irqtime minus the ksoftirqd time. This
is necessary because irq_time_read() is used to substract the IRQ time
from the sum_exec_runtime of a task. If we were to include the softirq
time of ksoftirqd, this task would substract its own CPU time everytime
it updates ksoftirqd->sum_exec_runtime which would therefore never
progress.
But this behaviour got broken by:
a499a5a14db ("sched/cputime: Increment kcpustat directly on irqtime account")
... which now includes ksoftirqd softirq time in the time returned by
irq_time_read().
This has resulted in wrong ksoftirqd cputime reported to userspace
through /proc/stat and thus "top" not showing ksoftirqd when it should
after intense networking load.
ksoftirqd->stime happens to be correct but it gets scaled down by
sum_exec_runtime through task_cputime_adjusted().
To fix this, just account the strict IRQ time in a separate counter and
use it to report the IRQ time.
Reported-and-tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Link: http://lkml.kernel.org/r/1493129448-5356-1-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This function just returns the same error code and sense data as
the default statement in the switch in the caller.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into features
Pull cpacf changes for KVM from Jason Herne:
Add query support for the KMA instruction.
|
|
_submit_bh() allowed submitting a buffer_head for I/O using custom
bio_flags. It used to be used by jbd to set BIO_SNAP_STABLE, introduced
by commit 713685111774 ("mm: make snapshotting pages for stable writes a
per-bio operation"). However, the code and flag has since been removed
and no _submit_bh() users remain.
These days, bio_flags are mostly used internally by the block layer to
track the state of bio's. As such, it doesn't really make sense for
filesystems to use them instead of op_flags when wanting special
behavior for block requests.
Therefore, remove _submit_bh() and trim the bio_flags argument from
submit_bh_wbc().
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
simple_fill_super() is passed an array of tree_descr structures which
describe the files to create in the filesystem's root directory. Since
these arrays are never modified intentionally, they should be 'const' so
that they are placed in .rodata and benefit from memory protection.
This patch updates the function signature and all users, and also
constifies tree_descr.name.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Drop duplicate header percpu-rwsem.h from linux/fs.h.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Previous AFFS patch fixed OFS write operations but unveiled
another bug: files greater than 4KB are being created with a wrong
size resulting in errors like the following:
dd if=/dev/zero of=file bs=4097 count=1
cp file /mnt/affs/
cp: error writing '/mnt/affs/file': Bad address
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
We called unconditionally affs_bread_ino() with create 0 resulting in
"error (device ...): get_block(): strange block request 0"
when trying to write on AFFS OFS format.
This patch adds create parameter to that function.
0 for affs_readpage_ofs()
1 for affs_write_begin_ofs()
Bug was found here:
https://bugzilla.kernel.org/show_bug.cgi?id=114961
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
node generation has to be stored on disk.
AFAICS we won't be able to manage it on AFFS.
This patch removes relevant check in affs_nfs_get_inode()
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Have that file in global include/linux is not needed.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
AFFS symbolic links were broken since kernel 2.6.29
Problem was bisected to the following
commit ebd09abbd969 ("vfs: ensure page symlinks are NUL-terminated")
commit 035146851cfa ("vfs: introduce helper function to safely
NUL-terminate symlinks")
AFFS wasn't setting inode size when reading symbolic link from disk or
creating a new one. Result was zero allocation in pagecache.
ln -s file symlink
ls -lrt
file
symlink ->
This patch adds inode isize information on inode get and symbolic link
addition.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The comment asserting that the value of struct statx_timestamp.tv_nsec
must be negative when statx_timestamp.tv_sec is negative, is wrong, as
could be seen from the following example:
#define _FILE_OFFSET_BITS 64
#include <assert.h>
#include <fcntl.h>
#include <stdio.h>
#include <sys/stat.h>
#include <unistd.h>
#include <asm/unistd.h>
#include <linux/stat.h>
int main(void)
{
static const struct timespec ts[2] = {
{ .tv_nsec = UTIME_OMIT },
{ .tv_sec = -2, .tv_nsec = 42 }
};
assert(utimensat(AT_FDCWD, ".", ts, 0) == 0);
struct stat st;
assert(stat(".", &st) == 0);
printf("st_mtim.tv_sec = %lld, st_mtim.tv_nsec = %lu\n",
(long long) st.st_mtim.tv_sec,
(unsigned long) st.st_mtim.tv_nsec);
struct statx stx;
assert(syscall(__NR_statx, AT_FDCWD, ".", 0, 0, &stx) == 0);
printf("stx_mtime.tv_sec = %lld, stx_mtime.tv_nsec = %lu\n",
(long long) stx.stx_mtime.tv_sec,
(unsigned long) stx.stx_mtime.tv_nsec);
return 0;
}
It expectedly prints:
st_mtim.tv_sec = -2, st_mtim.tv_nsec = 42
stx_mtime.tv_sec = -2, stx_mtime.tv_nsec = 42
The more generic comment asserting that the value of struct
statx_timestamp.tv_nsec might be negative is confusing to say the least.
It contradicts both the struct stat.st_[acm]time_nsec tradition and
struct timespec.tv_nsec requirements in utimensat syscall.
If statx syscall ever returns a stx_[acm]time containing a negative
tv_nsec that cannot be passed unmodified to utimensat syscall,
it will cause an immense confusion.
Fix this source of confusion by changing the type of struct
statx_timestamp.tv_nsec from __s32 to __u32.
Fixes: a528d35e8bfc ("statx: Add a system call to make enhanced file info available")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-api@vger.kernel.org
cc: mtk.manpages@gmail.com
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
trivial fix to spelling mistake in DEBUG2 debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This module specific flag can be made static as it does not need to be
in global scope.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Charles Chiou <charles.chiou@tw.promise.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
free_irq() expects the same device identity that was passed to
corresponding request_irq(), otherwise the IRQ is not freed.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There were pci_alloc_consistent() failures on ARM64 platform. Use
dma_alloc_coherent() with GFP_KERNEL flag DMA memory allocations.
Signed-off-by: Mahesh Rajashekhara <mahesh.rajashekhara@microsemi.com>
[hch: tweaked indentation, removed memsets]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
It could be just cmp 0xe instead of >>1 and cmp 0x7, with readable code.
Signed-off-by: Tomohiro Kusumi <tkusumi@tuxera.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
MASK_EE_STATUS added by 66ec6d59 was unused, but it seems to have been
defined to do this.
Signed-off-by: Tomohiro Kusumi <tkusumi@tuxera.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull sparc fixes from David Miller:
"I didn't want the release to go out without the statx system call
properly hooked up"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Update syscall tables.
sparc64: Fill in rest of HAVE_REGS_AND_STACK_ACCESS_API
|
|
With the new statx() syscall, the following both allow the attributes of
the file attached to a file descriptor to be retrieved:
statx(dfd, NULL, 0, ...);
and:
statx(dfd, "", AT_EMPTY_PATH, ...);
Change the code to reject the first option, though this means copying
the path and engaging pathwalk for the fstat() equivalent. dfd can be a
non-directory provided path is "".
[ The timing of this isn't wonderful, but applying this now before we
have statx() in any released kernel, before anybody starts using the
NULL special case. - Linus ]
Fixes: a528d35e8bfc ("statx: Add a system call to make enhanced file info available")
Reported-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Eric Sandeen <sandeen@sandeen.net>
cc: fstests@vger.kernel.org
cc: linux-api@vger.kernel.org
cc: linux-man@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
IOMMU harms performance signficantly when we run very fast networking
workloads. It's 40GB networking doing XDP test. Software overhead is
almost unaware, but it's the IOTLB miss (based on our analysis) which
kills the performance. We observed the same performance issue even with
software passthrough (identity mapping), only the hardware passthrough
survives. The pps with iommu (with software passthrough) is only about
~30% of that without it. This is a limitation in hardware based on our
observation, so we'd like to disable the IOMMU force on, but we do want
to use TBOOT and we can sacrifice the DMA security bought by IOMMU. I
must admit I know nothing about TBOOT, but TBOOT guys (cc-ed) think not
eabling IOMMU is totally ok.
So introduce a new boot option to disable the force on. It's kind of
silly we need to run into intel_iommu_init even without force on, but we
need to disable TBOOT PMR registers. For system without the boot option,
nothing is changed.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The multicast variable in the ieee80211_accept_frame() function is
treated as a boolean, but defined as int. Fix that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
At least on iwlwifi, sometimes lockdep complains that we can
lock
chanctx_mtx -> mvm.mutex -> iflist_mtx
(due to iterate_interfaces)
and
iflist_mtx -> chanctx_mtx
Remove the latter dependency in mac80211 by using the RTNL
that we already hold in one case, and can relatively easily
achieve in the other case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
ieee80211_frame_acked is called when a frame is acked by
the peer. In case this is a management frame, we check
if this an SMPS frame, in which case we can update our
antenna configuration.
When we parse the management frame we look at the category
in case it is an action frame. That byte sits after the IV
in case the frame was encrypted. This means that if the
frame was encrypted, we basically look at the IV instead
of looking at the category. It is then theorically
possible that we think that an SMPS action frame was acked
where really we had another frame that was encrypted.
Since the only management frame whose ack needs to be
tracked is the SMPS action frame, and that frame is not
a robust management frame, it will never be encrypted.
The easiest way to fix this problem is then to not look
at frames that were encrypted.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some of the enum definitions are unnamed but there's still
an attempt at documenting them - that doesn't work. Name
them to make that work.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add the definition for FT-8021.1X AKM selector as defined in
IEEE Std 802.11-2016, table 9-133.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add the definitions for SUITE_B and SUITE_B_192 AKM selectors as
defined in IEEE802.11REVmc_D5.0, table 9-132.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For multiple scheduled scan support the driver needs to know which
scheduled scan request is being stopped. Pass the request id in the
.sched_scan_stop() callback.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch allows for the scheduled scan request to specify matchsets
for specific BSSIDs.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[docs, netlink policy fix]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch implements the idea to have multiple scheduled scan requests
running concurrently. It mainly illustrates how to deal with the incoming
request from user-space in terms of backward compatibility. In order to
use multiple scheduled scans user-space needs to provide a flag attribute
NL80211_ATTR_SCHED_SCAN_MULTI to indicate support. If not the request is
treated as a legacy scan.
Drivers currently supporting scheduled scan are now indicating they support
a single scheduled scan request. This obsoletes WIPHY_FLAG_SUPPORTS_SCHED_SCAN.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
[clean up netlink destroy path to avoid allocations, code cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's no need to allocate a portid structure and then, for
each of those, walk the interfaces - we can just add a flag
to each interface and walk those directly. Due to padding in
the struct, we can even do it without any memory cost, and
it even simplifies the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Show the SCSI CDB for pending SCSI commands in
/sys/kernel/debug/block/*/mq/*/dispatch and */rq_list. An example
of how SCSI commands are displayed by this code:
ffff8801703245c0 {.op=READ, .cmd_flags=META PRIO, .rq_flags=DONTPREP IO_STAT STATS, .tag=14, .internal_tag=-1, .cmd=Read(10) 28 00 2a 81 1b 30 00 00 08 00}
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: <linux-scsi@vger.kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This new callback function will be used in the next patch to show
more information about SCSI requests.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Show the operation name, .cmd_flags and .rq_flags as names instead
of numbers.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
