| Age | Commit message (Collapse) | Author |
|---|
|
The implementation of svc_exit didn't take into account any stack hole
created by svc_entry; as happens with the undef handler when kprobes are
configured. The fix is to read the saved value of SP rather than trying
to calculate it.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
|
|
SCSI scanning of a channel:id:lun triplet in Linux works as follows
(function scsi_scan_target() in drivers/scsi/scsi_scan.c):
- If lun == SCAN_WILD_CARD, send a REPORT LUNS command to the target
and process the result.
- If lun != SCAN_WILD_CARD, send an INQUIRY command to the LUN
corresponding to the specified channel:id:lun triplet to verify
whether the LUN exists.
So a SCSI driver must either take the channel and target id values in
account in its quecommand() function or it should declare that it only
supports one channel and one target id.
Currently the ib_srp driver does neither. As a result scanning the
SCSI bus via e.g. rescan-scsi-bus.sh causes many duplicate SCSI
devices to be created. For each 0:0:L device, several duplicates are
created with the same LUN number and with (C:I) != (0:0). Fix this by
declaring that the ib_srp driver only supports one channel and one
target id.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: <stable@kernel.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
We can have valid but very low clocks in accessory detection modes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
If we have interrupts then wait for the FLL lock interrupt rather than
using dead reckoning when waiting for the FLL to start.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The individual devices should set the flag dcs_done_irq in the hubs
shared data structure to indicate that they will flag the interrupt
by calling wm_hubs_dcs_done().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This ensures appropriate clocking for bypass paths to speaker and
headphone and direct voice paths on affected revisions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Chip documentation explicitly requires that the reset values
of reserved register bits are left untouched. It is possible
there are differences between STA326 and STA328 or future
chip revisions in these bits, and clobbering them might
cause malfunction.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The STA32x has a number of preset EQ settings, but also
allows full user control of the biquad filter coeffcients
(when "Automode EQ" is set to "User").
Each biquad has five signed, 24bit, fixed-point coefficients
representing the range -1...1. The five biquad coefficients
can be uploaded in one atomic operation into on-chip
coefficient RAM.
There are also a few prescale, postscale and mixing
coefficients, in the same numeric format and range
(a negative coefficient inverts phase).
These coefficients are made available as SNDRV_CTL_ELEM_TYPE_BYTES
mixer controls.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Under some rare but real combinations of configuration parameters, RCU
callbacks are posted during early boot that use kernel facilities that
are not yet initialized. Therefore, when these callbacks are invoked,
hard hangs and crashes ensue. This commit therefore prevents RCU
callbacks from being invoked until after the scheduler is fully up and
running, as in after multiple tasks have been spawned.
It might well turn out that a better approach is to identify the specific
RCU callbacks that are causing this problem, but that discussion will
wait until such time as someone really needs an RCU callback to be invoked
(as opposed to merely registered) during early boot.
Reported-by: julie Sullivan <kernelmail.jms@gmail.com>
Reported-by: RKK <kulkarni.ravi4@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: julie Sullivan <kernelmail.jms@gmail.com>
Tested-by: RKK <kulkarni.ravi4@gmail.com>
|
|
The 'Solarstorm' brand is being retired and it's redundant with the
company name.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
Remove various bits left over from the old kdb-only btree tracing code, but
leave the actual trace point stubs in place to ease adding new event based
btree tracing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
Remove the dead hash table test rid which has been rotting away under
QUOTADEBUG, including some code that was compiled for normal debug
builds, but not actually called without QUOTADEBUG, and enable a few
cheap debug checks that were hidden under QUOTADEBUG for normal
debug builds.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
Replace the typeless b_fspriv2 and the ugly macros around it with a properly
typed transaction pointer. As a fallout the log buffer state debug checks
are also removed. We could have kept them using casts, but as they do
not have a real purpose we can as well just remove them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
xfs_da_grow_inode and xfs_dir2_grow_inode are mostly duplicate code. Factor
the meat of those two functions into a new common helper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
Change the bests array to be a proper variable sized entry. This is done
easily as no one relies on the size of the structure. Also change
XFS_DIR2_MAX_FREE_BESTS to an inline function while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
Replace the current mess of dir2 headers with just three that have a clear
purpose:
- xfs_dir2_format.h for all format definitions, including the inline helpers
to access our variable size structures
- xfs_dir2_priv.h for all prototypes that are internal to the dir2 code
and not needed by anything outside of the directory code. For this
purpose xfs_da_btree.c, and phase6.c in xfs_repair are considered part
of the directory code.
- xfs_dir2.h for the public interface to the directory code
In addition to the reshuffle I have also update the comments to not only
match the new file structure, but also to describe the directory format
better.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
Start the periodic sync workers only after we have finished xfs_mountfs
and thus fully set up the filesystem structures. Without this we can
call into xfs_qm_sync before the quotainfo strucute is set up if the
mount takes unusually long, and probably hit other incomplete states
as well.
Also clean up the xfs_fs_fill_super error path by using consistent
label names, and removing an impossible to reach case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Reviewed-by: Alex Elder <aelder@sgi.com>
|
|
Make shmobile use pm_genpd_poweroff_unused() instead of the
open-coded powering off PM domains without devices in use.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
|
|
Add a new function pm_genpd_poweroff_unused() queuing up the
execution of pm_genpd_poweroff() for every initialized generic PM
domain. Calling it will cause every generic PM domain without
devices in use to be powered off.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
|
|
This following code contains a dead "if (dev).." block:
...
for (i = 0; i < slip_maxdev; i++) {
dev = slip_devs[i];
if (dev == NULL)
break;
}
/* Sorry, too many, all slots in use */
if (i >= slip_maxdev)
return NULL;
if (dev) {
sl = netdev_priv(dev);
if (test_bit(SLF_INUSE, &sl->flags)) {
unregister_netdevice(dev);
dev = NULL;
slip_devs[i] = NULL;
}
}
...
The reason is that the code starting with "if (dev).." is never called as
when we found an empty slot (dev == NULL) we break the loop and "if (dev).."
not works eiter the loop ends and we get out with "i >= slip_maxdev".
Signed-off-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As slip_devs is initialized on module load stage there is no reason to
check it for NULL anywhere instead of the deinitialization routine because
if we can't get enough memory on startup we don't run at all.
Signed-off-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In sl_realloc_bufs() there is no reason to check if the requested MTU greater
than or equal to the current MTU value as this function called only
when requested
MTU not equals to the current value. So, the ">=" operation can be
safely replaced
with the ">".
Signed-off-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Matvejchikov Ilya <matvejchikov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This never, ever, happens.
Neighbour entries are always tied to one address family, and therefore
one set of dst_ops, and therefore one dst_ops->protocol "hh_type"
value.
This capability was blindly imported by Alexey Kuznetsov when he wrote
the neighbour layer.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get rid of all of the useless and costly indirection
by doing the neigh hash table lookup directly inside
of the neighbour binding.
Rename from arp_bind_neighbour to rt_bind_neighbour.
Use new helpers {__,}ipv4_neigh_lookup()
In rt_bind_neighbour() get rid of useless tests which
are never true in the context this function is called,
namely dev is never NULL and the dst->neighbour is
always NULL.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This pulls in all the drm fixes up to this point which are needed
for some -next patches to work.
|
|
drm_pci_device_is_pcie duplicates the funcationality of pci_is_pcie.
Convert callers of the former to the latter. This has the side benefit
of removing an unnecessary search in the PCI configuration space due to
using a saved PCIe capability offset.
[airlied: update for new callsite]
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Resize feature was supported by the commit 4e33f9eab07e but it was not
reflected to the list of unsupported features in nilfs2.txt file.
This updates the list to fix discrepancy.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
|
|
Compute drivers may change this, so make sure to emit it to
avoid errors in bo blits.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=39119
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Konstantin Belousov found an error in the define of G4x_GMCH_SIZE_VT_2M
relative to the GMCH specs, and confirmed that indeed one of his users
with a Q45 reports 0xb not 0xc for a 2/2MiB GATT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Konstantin Belousov <kostikbel@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
v2: incorporated suggestions from Randy Dunlap
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we cannot allocate new skbs in RX completion handler, we should
increase netdevice rx_dropped counter, not spam console messages.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In process and sleep allowed context, favor GFP_KERNEL allocations over
GFP_ATOMIC ones.
-v2: fixed checkpatch.pl warnings
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ben Greear <greearb@candelatech.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the Jumbo Frames feature on 82583 devices.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SPARSEMEM w/o VMEMMAP and DISCONTIGMEM, both used only on 32bit, use
sections array to map pfn to nid which is limited in granularity. If
NUMA nodes are laid out such that the mapping cannot be accurate, boot
will fail triggering BUG_ON() in mminit_verify_page_links().
On 32bit, it's 512MiB w/ PAE and SPARSEMEM. This seems to have been
granular enough until commit 2706a0bf7b (x86, NUMA: Enable
CONFIG_AMD_NUMA on 32bit too). Apparently, there is a machine which
aligns NUMA nodes to 128MiB and has only AMD NUMA but not SRAT. This
led to the following BUG_ON().
On node 0 totalpages: 2096615
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3927 pages, LIFO batch:0
Normal zone: 1740 pages used for memmap
Normal zone: 220978 pages, LIFO batch:31
HighMem zone: 16405 pages used for memmap
HighMem zone: 1853533 pages, LIFO batch:31
BUG: Int 6: CR2 (null)
EDI (null) ESI 00000002 EBP 00000002 ESP c1543ecc
EBX f2400000 EDX 00000006 ECX (null) EAX 00000001
err (null) EIP c16209aa CS 00000060 flg 00010002
Stack: f2400000 00220000 f7200800 c1620613 00220000 01000000 04400000 00238000
(null) f7200000 00000002 f7200b58 f7200800 c1620929 000375fe (null)
f7200b80 c16395f0 00200a02 f7200a80 (null) 000375fe 00000002 (null)
Pid: 0, comm: swapper Not tainted 2.6.39-rc5-00181-g2706a0b #17
Call Trace:
[<c136b1e5>] ? early_fault+0x2e/0x2e
[<c16209aa>] ? mminit_verify_page_links+0x12/0x42
[<c1620613>] ? memmap_init_zone+0xaf/0x10c
[<c1620929>] ? free_area_init_node+0x2b9/0x2e3
[<c1607e99>] ? free_area_init_nodes+0x3f2/0x451
[<c1601d80>] ? paging_init+0x112/0x118
[<c15f578d>] ? setup_arch+0x791/0x82f
[<c15f43d9>] ? start_kernel+0x6a/0x257
This patch implements node_map_pfn_alignment() which determines
maximum internode alignment and update numa_register_memblks() to
reject NUMA configuration if alignment exceeds the pfn -> nid mapping
granularity of the memory model as determined by PAGES_PER_SECTION.
This makes the problematic machine boot w/ flatmem by rejecting the
NUMA config and provides protection against crazy NUMA configurations.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/20110712074534.GB2872@htj.dyndns.org
LKML-Reference: <20110628174613.GP478@escobedo.osrc.amd.com>
Reported-and-Tested-by: Hans Rosenfeld <hans.rosenfeld@amd.com>
Cc: Conny Seidel <conny.seidel@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
DISCONTIGMEM on x86-32 implements pfn -> nid mapping similarly to
SPARSEMEM; however, it calls each mapping unit ELEMENT instead of
SECTION. This patch renames it to SECTION so that PAGES_PER_SECTION
is valid for both DISCONTIGMEM and SPARSEMEM. This will be used by
the next patch to implement mapping granularity check.
This patch is trivial constant rename.
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/20110712074422.GA2872@htj.dyndns.org
Cc: Hans Rosenfeld <hans.rosenfeld@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
The Dell Latitude E6320 doesn't reboot unless reboot=pci is set.
Force it thanks to DMI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: http://lkml.kernel.org/r/1309269451-4966-1-git-send-email-maxime.ripard@free-electrons.com
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
sound/isa/es18xx.c: In function ‘snd_es18xx_playback1_prepare’:
sound/isa/es18xx.c:501:9: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/es18xx.c: In function ‘snd_es18xx_playback_pointer’:
sound/isa/es18xx.c:818:3: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[2]: *** [sound/isa/es18xx.o] Error 1
sound/isa/sscape.c: In function ‘upload_dma_data’:
sound/isa/sscape.c:481:3: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[2]: *** [sound/isa/sscape.o] Error 1
sound/isa/ad1816a/ad1816a_lib.c: In function ‘snd_ad1816a_playback_prepare’:
sound/isa/ad1816a/ad1816a_lib.c:244:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/ad1816a/ad1816a_lib.c: In function ‘snd_ad1816a_playback_pointer’:
sound/isa/ad1816a/ad1816a_lib.c:302:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
sound/isa/ad1816a/ad1816a_lib.c: In function ‘snd_ad1816a_free’:
sound/isa/ad1816a/ad1816a_lib.c:544:3: error: implicit declaration of function ‘snd_dma_disable’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/ad1816a/ad1816a_lib.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/ad1816a] Error 2
sound/isa/es1688/es1688_lib.c: In function ‘snd_es1688_playback_prepare’:
sound/isa/es1688/es1688_lib.c:417:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/es1688/es1688_lib.c: In function ‘snd_es1688_playback_pointer’:
sound/isa/es1688/es1688_lib.c:509:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/es1688/es1688_lib.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/es1688] Error 2
sound/isa/gus/gus_dma.c: In function ‘snd_gf1_dma_program’:
sound/isa/gus/gus_dma.c:79:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/gus/gus_dma.c: In function ‘snd_gf1_dma_done’:
sound/isa/gus/gus_dma.c:177:3: error: implicit declaration of function ‘snd_dma_disable’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/gus/gus_dma.o] Error 1
sound/isa/gus/gus_pcm.c: In function ‘snd_gf1_pcm_capture_prepare’:
sound/isa/gus/gus_pcm.c:591:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/gus/gus_pcm.c: In function ‘snd_gf1_pcm_capture_pointer’:
sound/isa/gus/gus_pcm.c:619:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/gus/gus_pcm.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/gus] Error 2
sound/isa/sb/sb16_csp.c: In function ‘snd_sb_csp_ioctl’:
sound/isa/sb/sb16_csp.c:228:227: error: case label does not reduce to an integer constant
make[3]: *** [sound/isa/sb/sb16_csp.o] Error 1
sound/isa/sb/sb16_main.c: In function ‘snd_sb16_playback_prepare’:
sound/isa/sb/sb16_main.c:276:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/sb/sb16_main.c: In function ‘snd_sb16_playback_pointer’:
sound/isa/sb/sb16_main.c:456:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/sb/sb16_main.o] Error 1
sound/isa/sb/sb8_main.c: In function ‘snd_sb8_playback_prepare’:
sound/isa/sb/sb8_main.c:172:3: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/sb/sb8_main.c: In function ‘snd_sb8_playback_pointer’:
sound/isa/sb/sb8_main.c:425:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/sb/sb8_main.o] Error 1
make[3]: Target `__build' not remade because of errors.
make[2]: *** [sound/isa/sb] Error 2
sound/isa/wss/wss_lib.c: In function ‘snd_wss_playback_prepare’:
sound/isa/wss/wss_lib.c:1025:2: error: implicit declaration of function ‘snd_dma_program’ [-Werror=implicit-function-declaration]
sound/isa/wss/wss_lib.c: In function ‘snd_wss_playback_pointer’:
sound/isa/wss/wss_lib.c:1160:2: error: implicit declaration of function ‘snd_dma_pointer’ [-Werror=implicit-function-declaration]
sound/isa/wss/wss_lib.c: In function ‘snd_wss_free’:
sound/isa/wss/wss_lib.c:1695:3: error: implicit declaration of function ‘snd_dma_disable’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [sound/isa/wss/wss_lib.o] Error 1
warning: (RADIO_MIROPCM20) selects SND_ISA which has unmet direct dependencies (SOUND && !M68K && SND && ISA && ISA_DMA_API)
A build with ISA && ISA_DMA && !ISA_DMA_API results in:
CC sound/isa/es18xx.o
CC sound/isa/sscape.o
CC sound/isa/ad1816a/ad1816a_lib.o
CC sound/isa/es1688/es1688_lib.o
CC sound/isa/gus/gus_dma.o
CC sound/isa/gus/gus_pcm.o
CC sound/isa/sb/sb16_csp.o
CC sound/isa/sb/sb16_main.o
CC sound/isa/sb/sb8_main.o
CC sound/isa/wss/wss_lib.o
The root cause for this is hidden in this Kconfig warning:
Adding a dependency on ISA_DMA_API to RADIO_MIROPCM20 fixes these issues.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
trimslice and paz00 both have functionally identical platform
data for the tegra-ehci driver. Move the platform data into
devices.c, and remove it from all the board files.
Signed-off-by: Colin Cross <ccross@android.com>
Tested-by: Konstantin Sinyuk <kostyas@compulab.co.il>
Acked-by: Olof Johansson <olof@lixom.net>
|
|
The real-mode kernel header init_size field is located at 0x260 per the field
listing in th e"REAL-MODE KERNEL HEADER" section. It is listed as 0x25c in
the "DETAILS OF HEADER FIELDS" section, which overlaps with pref_address.
Correct the details listing to 0x260.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Link: http://lkml.kernel.org/r/541cf88e2dfe5b8186d8b96b136d892e769a68c1.1310441260.git.dvhart@linux.intel.com
CC: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Every board file includes the same platform data definition
for the i2c-tegra driver's bus speed. Move the platform data
into devices.c, and remove it from all the board files.
Signed-off-by: Colin Cross <ccross@android.com>
Tested-by: Konstantin Sinyuk <kostyas@compulab.co.il>
Acked-by: Olof Johansson <olof@lixom.net>
|
