| Age | Commit message (Collapse) | Author |
|---|
|
Fixing the remote device state machine to suspend and terminate
all outstanding I/O before the device stopped state is reached.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
When the remote device enters the NCQ error state, the device must
be suspended so that the I/O terminations can take place.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
TCs must be terminated only while the RNC is suspended. This commit
adds remote device suspensions and resumptions in the abort, reset and
termination paths.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
TCs must only be terminated when RNCs are suspended.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Add comprehensive decode for all TC completions that generate RNC
suspensions.
Note that this commit also removes unconditional resumptions of ATAPI
devices when in the SCI_STP_DEV_ATAPI_ERROR state, and STP devices
when in the SCI_STP_DEV_IDLE state. This is because the SCI_STP_DEV_IDLE
and SCI_STP_DEV_ATAPI state entry functions manage the RNC resumption.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The resumption from the Tx/Rx suspended state should work the same
as the Tx suspended state.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
For STP devices under certain protocol conditions, an RNC will not
suspend until the current transfer state is broken with a SYNC/ESC
sequence from the SCU. The SYNC/ESC driven by expiration of the
SCU link layer hang detect timer, which has too small a dynamic
range to support slow SATA devices, so normally it is disabled.
This change enables the timer with the minimum period at the point
when the suspension is requested.
Note that there is potential collateral damage to other open
connections to slow SATA devices on the same port, since there
is no alternative but to enable the LLHANG timer on every phy in
the port for the current suspension request - there is no way to
tell on which phy the RNC in question is currently active.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The support for CONFIG_MCA is being removed, since the 20
year old hardware simply isn't capable of meeting today's
software demands on CPU and memory resources.
This commit removes any MCA specific net drivers, and removes
any MCA specific probe/support code from drivers that were
doing a dual ISA/MCA role.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull two more target-core updates from Nicholas Bellinger:
"The first patch addresses a SPC-2 reservations RELEASE bug in a
special (iscsi specific) multi-ISID setup case that was allowing the
same initiator to be able to incorrect release it's own reservation on
a different SCSI path with enforce_pr_isid=1 operation. This bug was
caught by Bernhard Kohl.
The second patch is to address a bug with FILEIO backends where the
incorrect number of blocks for READ_CAPACITY was being reported after
an underlying device-mapper block_device size change. This patch uses
now i_size_read() in fd_get_blocks() for FILEIO backends with an
underlying block_device, instead of trying to determine this value at
setup time during fd_create_virtdevice(). (hch CC'ed)
Both are CC'ed to stable."
* '3.4-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix bug in handling of FILEIO + block_device resize ops
target: Fix SPC-2 RELEASE bug for multi-session iSCSI client setups
|
|
Change the TX ring scheme such that the number of rings for untagged packets
and for tagged packets (per each of the vlan priorities) is the same, unlike
the current situation where for tagged traffic there's one ring per priority
and for untagged rings as the number of core.
Queue selection is done as follows:
If the mqprio qdisc is operates on the interface, such that the core networking
code invoked the device setup_tc ndo callback, a mapping of skb->priority =>
queue set is forced - for both, tagged and untagged traffic.
Else, the egress map skb->priority => User priority is used for tagged traffic, and
all untagged traffic is sent through tx rings of UP 0.
The patch follows the convergence of discussing that issue with John Fastabend
over this thread http://comments.gmane.org/gmane.linux.network/229877
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Liran Liss <liranl@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When I first wrote drop monitor I wrote it to just build monolithically. There
is no reason it can't be built modularly as well, so lets give it that
flexibiity.
I've tested this by building it as both a module and monolithically, and it
seems to work quite well
Change notes:
v2)
* fixed for_each_present_cpu loops to be more correct as per Eric D.
* Converted exit path failures to BUG_ON as per Ben H.
v3)
* Converted del_timer to del_timer_sync to close race noted by Ben H.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev_alloc_skb() is used by networks driver in their RX path to
allocate an skb to receive an incoming frame.
With recent skb->head_frag infrastructure, it makes sense to change
netdev_alloc_skb() to use build_skb() and a frag allocator.
This permits a zero copy splice(socket->pipe), and better GRO or TCP
coalescing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The padding destination or hop-by-hop option is called Pad1 and not Pad0.
See RFC2460 (4.2) or the IANA ipv6-parameters registry:
http://www.iana.org/assignments/ipv6-parameters/ipv6-parameters.xml
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix some minor problems in comments of etherdevice.h
* Warning is out dated, file hasn't moved or disappeared in many years and
is unlikely to do so soon.
* Capitalize Ethernet consistently since it is a proper name
* Fix descriptive comment of padding
* Spelling and grammar fix for alignment comment
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch removes unused return value from __delete_item() and
delete_item() methods in drivers/net/ppp/pppoe.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
OEM parameters [1] are parsed from the platform option-rom / efi
driver. By default the driver was validating the parameters for the
dual-controller case, but in single-controller case only the first set
of parameters may be valid.
Limit the validation to the number of actual controllers detected
otherwise the driver may fail to parse the valid parameters leading to
driver-load or runtime failures.
[1] the platform specific set of phy address, configuration,and analog
tuning values
[stable v3.0+]
Cc: <stable@vger.kernel.org>
Reported-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Ensure we enable receiving BCN's from the
hardware when adding phy to isci_port.
Otherwise if we get BCN before the port is
created we won't see any BCN
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Reported-by: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
This patch extends timings in COMSAS signaling, so ISCI can detect disc
drives having issues to send COMSAS in correct time frame.
Signed-off-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
We can retrieve the shost from the sas_ha like the rest of libsas and
drop this out of our local data structure.
Acked-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
There is a (dubious?) lost irq workaround in sci_controller_isr() that
effectively nullifies attempts to disable interrupts. Until the
workaround can be re-evaluated add some infrastructure to prevent the
interrupt handler from inadvertantly re-enabling interrupts.
The failure mode was interrupts continuing to run after the driver had
been removed and its iomappings torn down.
Reported-by: Jacek Danecki <jacek.danecki@intel.com>
Tested-by: Jacek Danecki <jacek.danecki@intel.com>
[richard: clear remaining interrupts at the end of reset]
Acked-by: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The call to wait_for_start() is meant to ensure that all links have been
given a chance to come up before letting the kernel proceed with
probing. However, the implementation is not correctly syncing with the
port configuration agent. In the MPC case the ports are hard-coded, in
the APC case we need to wait for the port-configuration to form ports
from the started phys.
Towards that end increase the timeout for the APC agent to form ports,
and delay start complete until all phys are out of link-training.
Cc: <stable@vger.kernel.org>
Cc: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
1/ notify waiters when controller stop completes (fixes 10 second stall
unloading the driver)
2/ make sure phy stop is after port and device stop
Cc: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Based on an original implementation by Ed Nadolski and Artur Wojcik
In preparation for S3/S4 support refactor initialization so that
driver-load and resume-from-suspend can share the common init path of
isci_host_init(). Organize the initialization into objects that are
self-contained to the driver (initialized by isci_host_init) versus
those that have some upward registration (initialized at allocation time
asd_sas_phy, asd_sas_port, dma allocations). The largest change is
moving the the validation of the oem and module parameters from
isci_host_init() to isci_host_alloc().
The S3/S4 approach being taken is that libsas will be tasked with
remembering the state of the domain and the lldd is free to be
forgetful. In the case of isci we'll just re-init using a subset of the
normal driver load path.
[clean up some unused / mis-indented function definitions in host.h]
Signed-off-by: Ed Nadolski <edmund.nadolski@intel.com>
Signed-off-by: Artur Wojcik <artur.wojcik@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Another unused field, and isci_port_init is overkill.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
They serve no incremental purpose over the existing sas_ha state.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Per the SAS spec, several types of BROADCAST CHANGE primitives
must cause re-discovery of the originating expander.
Only the standard BROADCAST CHANGE primitive was being
sent to the LIBSAS layer. The other BC primitives have been
added to the sci_phy_event_handler()
Signed-off-by: Tom Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Holdovers from the initial driver cleanup, replace with enum sas_protocol.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
domain_device ->parent conveys the same information.
Occurrences of ->is_direct_attached appear next to incomplete open-coded
versions of dev_is_sata(), clean those up as well.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Convert controller state machine warnings to emit the state number (it
missed the number to string conversion, but since these error rarely
happen not much motivation to go further).
Fix up the rnc warnings to use the state name.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
|
|
Neither "acceptor_values" nor "proposer_values" can be NULL here when
scanning the value lists for incoming iSCSI login parameters such as
HeaderDigest=CRC32C,None.
Smatch complains because we are not allowed to pass NULL pointers to
strchr(). Also I removed a second later check for "!acceptor_values"
because it gets checked on the next line in the do while condition.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a bug in the handling of FILEIO w/ underlying block_device
resize operations where the original fd_dev->fd_dev_size was incorrectly being
used in fd_get_blocks() for READ_CAPACITY response payloads.
This patch avoids using fd_dev->fd_dev_size for FILEIO devices with
an underlying block_device, and instead changes fd_get_blocks() to
get the sector count directly from i_size_read() as recommended by hch.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
bool conversions where possible.
__inline__ -> inline
space cleanups
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull slave-dmaengine fixes fromVinod Koul:
"fixes of cylic dma usages in slave dma drivers"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: fix cyclic dma usage
dmaengine: pl330: dont complete descriptor for cyclic dma
|
|
Pull last minute virtio fixes from Michael S. Tsirkin:
"Here are a couple of last minute virtio fixes for 3.4. Hope it's not
too late yes - I might have tried too hard to make sure the fix is
well tested.
Fixes are by Amit and myself. One fixes module removal and one
suspend of a VM, the last one the handling of out of memory condition.
They are thus very low risk as most people never hit these paths, but
do fix very annoying problems for people that do use the feature.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_net: invoke softirqs after __napi_schedule
virtio: balloon: let host know of updated balloon size before module removal
virtio: console: tell host of open ports after resume from s3/s4
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM: SoC fixes from Olof Johansson:
"I will stop trying to predict when we're done with fixes for a
release.
Here's another small batch of three patches for arm-soc:
- A fix for a boot time WARN_ON() due to irq domain conversion on
PRIMA2
- Fix for a regression in Tegra SMP spinup code due to swapped
register offsets
- Fixed config dependency for mv_cesa crypto driver to avoid build
breakage"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: PRIMA2: fix irq domain size and IRQ mask of internal interrupt controller
crypto: mv_cesa requires on CRYPTO_HASH to build
ARM: tegra: Fix flow controller accesses
|
|
Pull two md fixes from NeilBrown:
"One fixes a bug in the new raid10 resize code so is relevant to 3.4
only.
The other fixes a bug in the use of md by dm-raid, so is relevant to
any kernel with dm-raid support"
* tag 'md-3.4-fixes' of git://neil.brown.name/md:
MD: Add del_timer_sync to mddev_suspend (fix nasty panic)
md/raid10: set dev_sectors properly when resizing devices in array.
|
|
'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf, x86 and scheduler updates from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tracing: Do not enable function event with enable
perf stat: handle ENXIO error for perf_event_open
perf: Turn off compiler warnings for flex and bison generated files
perf stat: Fix case where guest/host monitoring is not supported by kernel
perf build-id: Fix filename size calculation
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, kvm: KVM paravirt kernels don't check for CPUID being unavailable
x86: Fix section annotation of acpi_map_cpu2node()
x86/microcode: Ensure that module is only loaded on supported Intel CPUs
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix KVM and ia64 boot crash due to sched_groups circular linked list assumption
|
|
Commit ff9a184c ("ARM: 7400/1: vfp: clear fpscr length and stride bits
on entry to sig handler") flushes the VFP state prior to entering a
signal handler so that a VFP operation inside the handler will trap and
force a restore of ABI-compliant registers. Reflushing and disabling VFP
on the sigreturn path is predicated on the saved thread state indicating
that VFP was used by the handler -- however for SMP platforms this is
only set on context-switch, making the check unreliable and causing VFP
register corruption in userspace since the register values are not
necessarily those restored from the sigframe.
This patch unconditionally flushes the VFP state after a signal handler.
Since we already perform the flush before the handler and the flushing
itself happens lazily, the redundant flush when VFP is not used by the
handler is essentially a nop.
Reported-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
A zero value for prot_sect in the memory types table implies that
section mappings should never be created for the memory type in question.
This is checked for in alloc_init_section().
With LPAE, we set a bit to mask access flag faults for kernel mappings.
This breaks the aforementioned (!prot_sect) check in alloc_init_section().
This patch fixes this bug by first checking for a non-zero
prot_sect before setting the PMD_SECT_AF flag.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Under certain scenarios, it's possible that bursty manageability traffic
over the BMC-to-OS path may overrun the internal manageability receive
buffer causing dropped manageability packets. Clearing this bit prevents
this situation by interrupting coalescing to allow manageability traffic
through.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The code seems to want to look at the last byte where the HW puts some
information. Since the skb->data area is never seen by the HW I guess it
does not work as expected. We pass the page address to the HW so I
*think* in order to get to the last byte where the information might be
one should use the page buffer and take a look.
This is of course not more than just compile tested.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
According to the comment, errata 23 says that the memory we allocate
can't cross a 64KiB boundary. In case of jumbo frames we allocate
complete pages which can never cross the 64KiB boundary because
PAGE_SIZE should be a multiple of 64KiB so we stop either before the
boundary or start after it but never cross it. Furthermore the check
seems bogus because it looks at skb->data which is not seen by the HW
at all because we only pass the DMA address of the page we allocated. So
I *think* the workaround is not required here.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This define is needed by i217.
Reported-by: Bjorn Mork <bjorn@mork.no>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
error-handling host reset handler
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
an els echo
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
queues
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
