| Age | Commit message (Collapse) | Author |
|---|
|
These are Gen3 Aquantia N-BASET PHYs which support 5GBASE-T,
2.5GBASE-T, 1000BASE-T and 100BASE-TX (not 10G); also EEE, Sync-E,
PTP, PoE.
The 112 is a single PHY package, the 412 is a quad PHY package.
The system-side SERDES interface of these PHYs selects its protocol
depending on the negotiated media side link speed. That protocol can be
1000BASE-X, 2500BASE-X, 10GBASE-R, SGMII, USXGMII.
The configuration of which SERDES protocol to use for which link speed
is made by firmware; even though it could be overwritten over MDIO by
Linux, we assume that the firmware provisioning is ok for the board on
which the driver probes.
For cases when the system side runs at a fixed rate, we want phylib/phylink
to detect the PAUSE rate matching ability of these PHYs, so we need to
use the Aquantia rather than the generic C45 driver. This needs
aqr107_read_status() -> aqr107_read_rate() to set phydev->rate_matching,
as well as the aqr107_get_rate_matching() method.
I am a bit unsure about the naming convention in the driver. Since
AQR107 is a Gen2 PHY, I assume all functions prefixed with "aqr107_"
rather than "aqr_" mean Gen2+ features. So I've reused this naming
convention.
I've tested PHY "SGMII" statistics as well as the .link_change_notify
method, which prints:
Aquantia AQR412 mdio_mux-0.4:00: Link partner is Aquantia PHY, FW 4.3, fast-retrain downshift advertised, fast reframe advertised
Tested SERDES protocols are usxgmii and 2500base-x (the latter with
PAUSE rate matching). Tested link modes are 100/1000/2500 Base-T
(with Aquantia link partner and with other link partners). No notable
events observed.
The placement of these PHY IDs in the driver is right before AQR113C,
a Gen4 PHY.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
1) Fix sparse warning in the new nft_inner expression, reported
by Jakub Kicinski.
2) Incorrect vlan header check in nft_inner, from Peng Wu.
3) Two patches to pass reset boolean to expression dump operation,
in preparation for allowing to reset stateful expressions in rules.
This adds a new NFT_MSG_GETRULE_RESET command. From Phil Sutter.
4) Inconsistent indentation in nft_fib, from Jiapeng Chong.
5) Speed up siphash calculation in conntrack, from Florian Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: conntrack: use siphash_4u64
netfilter: rpfilter/fib: clean up some inconsistent indenting
netfilter: nf_tables: Introduce NFT_MSG_GETRULE_RESET
netfilter: nf_tables: Extend nft_expr_ops::dump callback parameters
netfilter: nft_inner: fix return value check in nft_inner_parse_l2l3()
netfilter: nft_payload: use __be16 to store gre version
====================
Link: https://lore.kernel.org/r/20221115095922.139954-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The NFP documentation is updated to include information about Corigine,
and the new NFP3800 chips. The 'Acquiring Firmware' section is updated
with new information about where to find firmware.
Two new sections are added to expand the coverage of the documentation.
The new sections include:
- Devlink Info
- Configure Device
Signed-off-by: Walter Heymans <walter.heymans@corigine.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20221115090834.738645-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
'mtk_eth_soc-rx-vlan-offload-improvement-dsa-hardware-untag-support'
Felix Fietkau says:
====================
mtk_eth_soc rx vlan offload improvement + dsa hardware untag support
This series improves rx vlan offloading on mtk_eth_soc and extends it to
support hardware DSA untagging where possible.
This improves performance by avoiding calls into the DSA tag driver receive
function, including mangling of skb->data.
This is split out of a previous series, which added other fixes and
multiqueue support
====================
Link: https://lore.kernel.org/r/20221114124214.58199-1-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
x25_lapb_receive_frame() using skb_copy() to get a private copy of
skb, the new skb should be freed in the undersized/fragmented skb
error handling path. Otherwise there is a memory leak.
Fixes: cb101ed2c3c7 ("x25: Handle undersized/fragmented skbs")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Link: https://lore.kernel.org/r/20221114110519.514538-1-weiyongjun@huaweicloud.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ag71xx_open()
If ag71xx_hw_enable() fails, call phylink_disconnect_phy() to clean up.
And if phylink_of_phy_connect() fails, nothing needs to be done.
Compile tested only.
Fixes: 892e09153fa3 ("net: ag71xx: port to phylink")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20221114095549.40342-1-liujian56@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
- pass the tag to DSA via metadata dst
- disabled on 7986 for now, since it's not working yet
- disabled if a MAC is enabled that does not use DSA
This improves performance by bypassing the DSA tag driver and avoiding extra
skb data mangling
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Keep the vlan rx offload feature in sync across all netdevs belonging to the
device, since the feature is global and can't be turned off per MAC
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the id from the DMA descriptor instead of hardcoding 802.1q
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If a metadata dst is present with the type METADATA_HW_PORT_MUX on a dsa cpu
port netdev, assume that it carries the port number and that there is no DSA
tag present in the skb data.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Eduard Zingerman says:
====================
This patchset adds ability to propagates nullness information for
branches of register to register equality compare instructions. The
following rules are used:
- suppose register A maybe null
- suppose register B is not null
- for JNE A, B, ... - A is not null in the false branch
- for JEQ A, B, ... - A is not null in the true branch
E.g. for program like below:
r6 = skb->sk;
r7 = sk_fullsock(r6);
r0 = sk_fullsock(r6);
if (r0 == 0) return 0; (a)
if (r0 != r7) return 0; (b)
*r7->type; (c)
return 0;
It is safe to dereference r7 at point (c), because of (a) and (b).
The utility of this change came up while working on BPF CLang backend
issue [1]. Specifically, while debugging issue with selftest
`test_sk_lookup.c`. This test has the following structure:
int access_ctx_sk(struct bpf_sk_lookup *ctx __CTX__)
{
struct bpf_sock *sk1 = NULL, *sk2 = NULL;
...
sk1 = bpf_map_lookup_elem(&redir_map, &KEY_SERVER_A);
if (!sk1) // (a)
goto out;
...
if (ctx->sk != sk1) // (b)
goto out;
...
if (ctx->sk->family != AF_INET || // (c)
ctx->sk->type != SOCK_STREAM ||
ctx->sk->state != BPF_TCP_LISTEN)
goto out;
...
}
- at (a) `sk1` is checked to be not null;
- at (b) `ctx->sk` is verified to be equal to `sk1`;
- at (c) `ctx->sk` is accessed w/o nullness check.
Currently Global Value Numbering pass considers expressions `sk1` and
`ctx->sk` to be identical at point (c) and replaces `ctx->sk` with
`sk1` (not expressions themselves but corresponding SSA values).
Since `sk1` is known to be not null after (b) verifier allows
execution of the program.
However, such optimization is not guaranteed to happen. When it does
not happen verifier reports an error.
Changelog:
v2 -> v3:
- verifier tests are updated with correct error message for
unprivileged mode (pointer comparisons are forbidden in
unprivileged mode).
v1 -> v2:
- after investigation described in [2] as suggested by John, Daniel
and Shung-Hsi, function `type_is_pointer` is removed, calls to this
function are replaced by `__is_pointer_value(false, src_reg)`.
RFC -> v1:
- newly added if block in `check_cond_jmp_op` is moved down to keep
`make_ptr_not_null_reg` actions together;
- tests rewritten to have a single `r0 = 0; exit;` block.
[1] https://reviews.llvm.org/D131633#3722231
[2] https://lore.kernel.org/bpf/bad8be826d088e0d180232628160bf932006de89.camel@gmail.com/
[RFC] https://lore.kernel.org/bpf/20220822094312.175448-1-eddyz87@gmail.com/
[v1] https://lore.kernel.org/bpf/20220826172915.1536914-1-eddyz87@gmail.com/
[v2] https://lore.kernel.org/bpf/20221106214921.117631-1-eddyz87@gmail.com/
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Verify that nullness information is porpagated in the branches of
register to register JEQ and JNE operations.
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/r/20221115224859.2452988-3-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Propagate nullness information for branches of register to register
equality compare instructions. The following rules are used:
- suppose register A maybe null
- suppose register B is not null
- for JNE A, B, ... - A is not null in the false branch
- for JEQ A, B, ... - A is not null in the true branch
E.g. for program like below:
r6 = skb->sk;
r7 = sk_fullsock(r6);
r0 = sk_fullsock(r6);
if (r0 == 0) return 0; (a)
if (r0 != r7) return 0; (b)
*r7->type; (c)
return 0;
It is safe to dereference r7 at point (c), because of (a) and (b).
Signed-off-by: Eduard Zingerman <eddyz87@gmail.com>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/r/20221115224859.2452988-2-eddyz87@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull netfx fixes from David Howells:
"Two fixes, affecting the functions that iterates over the pagecache
unmarking or unlocking pages after an op is complete:
- xas_for_each() loops must call xas_retry() first thing and
immediately do a "continue" in the case that the extracted value is
a special value that indicates that the walk raced with a
modification. Fix the unlock and unmark loops to do this.
- The maths in the unlock loop is dodgy as it could, theoretically,
at some point in the future end up with a starting file pointer
that is in the middle of a folio. This will cause a subtraction to
go negative - but the number is unsigned. Fix the maths to use
absolute file positions instead of relative page indices"
* tag 'netfs-fixes-20221115' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
netfs: Fix dodgy maths
netfs: Fix missing xas_retry() calls in xarray iteration
|
|
Current dual mode adaptor ("DP++") detection code assumes that all
adaptors support i2c sub-addressing for read operations from the
DP-HDMI adaptor ID buffer. It has been observed that multiple
adaptors do not in fact support this, and always return data starting
at register 0. On affected adaptors, the code fails to read the proper
registers that would identify the device as a type 2 adaptor, and
handles those as type 1, limiting the TMDS clock to 165MHz, even if
the according register would announce a higher TMDS clock.
Fix this by always reading the ID buffer starting from offset 0, and
discarding any bytes before the actual offset of interest.
We tried finding authoritative documentation on whether or not this is
allowed behaviour, but since all the official VESA docs are paywalled,
the best we could come up with was the spec sheet for Texas Instruments'
SNx5DP149 chip family.[1] It explicitly mentions that sub-addressing is
supported for register writes, but *not* for reads (See NOTE in
section 8.5.3). Unless TI openly decided to violate the VESA spec, one
could take that as a hint that sub-addressing is in fact not mandated
by VESA.
The other two adaptors affected used the PS8409(A) and the LT8611,
according to the data returned from their ID buffers.
[1] https://www.ti.com/lit/ds/symlink/sn75dp149.pdf
Cc: stable@vger.kernel.org
Signed-off-by: Simon Rettberg <simon.rettberg@rz.uni-freiburg.de>
Reviewed-by: Rafael Gieschke <rafael.gieschke@rz.uni-freiburg.de>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221006113314.41101987@computer
Acked-by: Jani Nikula <jani.nikula@intel.com>
|
|
If the returning value of SMB2_close_init is an error-value,
exit the function.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 352d96f3acc6 ("cifs: multichannel: move channel selection above transport layer")
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fixes from Gao Xiang:
"Most patches randomly fix error paths or corner cases in fscache mode
reported recently. One fixes an invalid access relating to fragments
on crafted images.
Summary:
- Fix packed_inode invalid access when reading fragments on crafted
images
- Add a missing erofs_put_metabuf() in an error path in fscache mode
- Fix incorrect `count' for unmapped extents in fscache mode
- Fix use-after-free of fsid and domain_id string when remounting
- Fix missing xas_retry() in fscache mode"
* tag 'erofs-for-6.1-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: fix missing xas_retry() in fscache mode
erofs: fix use-after-free of fsid and domain_id string
erofs: get correct count for unmapped range in fscache mode
erofs: put metabuf in error path in fscache mode
erofs: fix general protection fault when reading fragment
|
|
The workaround designed for some specific ASICs is wrongly applied
to SMU13 ASICs. That leads to some runpm hang.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Enable SMU13.0.7 runpm support.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
|
|
Enable SMU13.0.0 runpm support.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
|
|
If we enable virtual display functionality on parts with
no display hardware we can end up trying to check for and
reserve the vbios FB area on devices where it doesn't exist.
Check if display hardware is actually present on the hardware
before trying to reserve the memory.
v2: move the check into common code
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It is to resolve a regression, which fails to allocate
VRAM due to no free memory in application, the reason
is we add check of vram_pin_size for memory limit, and
application is pinning the memory for Peerdirect, KFD
should not count it in memory limit. So removing
vram_pin_size will resolve it.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Otherwise, some unexpected PCIE AER errors will be observed
in runtime suspend/resume cycle.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
DM maps DRM CRTC degamma to DPP (pre-blending) degamma block, but DCE doesn't
support programmable degamma curve anywhere. Currently, a custom degamma is
accepted by DM but just ignored by DCE driver and degamma correction isn't
actually applied. There is no way to map custom degamma in DCE, therefore, DRM
CRTC degamma property shouldn't be enabled for DCE drivers.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[WHY?]
Max number of lines that can be used for prefetch due to type constraints is
63.75.
[HOW?]
Enforce maximum prefetch lines as 63.75.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY?]
DCN32 uses fclk pstate watermarks for dummy pstate, and must always be
supported.
[HOW?]
Validation needs to be run with fclk pstate latency set
as the dummy pstate latency to get correct prefetch and bandwidth outputs.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Description]
Prefetch calculation loop was not exiting until utilizing all of vstartup if it
failed once. Locals need to be reset on each iteration of the loop.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
|
|
[Why]
dcn314 uses optc2_configure_crc() that wraps
optc1_configure_crc() + set additional registers
not applicable to dcn314.
It's not critical but when used leads to warning like:
WARNING: drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c
Call Trace:
<TASK>
generic_reg_set_ex+0x6d/0xe0 [amdgpu]
optc2_configure_crc+0x60/0x80 [amdgpu]
dc_stream_configure_crc+0x129/0x150 [amdgpu]
amdgpu_dm_crtc_configure_crc_source+0x5d/0xe0 [amdgpu]
[How]
Use optc1_configure_crc() directly
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
|
|
[Why]
The cursor size (in memory) is currently incorrectly calculated,
resulting not enough CAB being allocated for static screen cursor
in MALL refresh. This results in cursor image corruption.
[How]
Use cursor pitch instead of cursor width when calculating cursor size.
Update num cache lines calculation to use the result of the cursor size
calculation instead of manually recalculating again.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
|
|
This reverts commit 981f09295687f856d5345e19c7084aca481c1395.
It turns out this causes logically active but disconnected DP MST
connectors to disappear from the KMS resources list, and Mutter
then assumes the connector is already disabled. Later on Mutter tries
to re-use the same CRTC but fails since on the kernel side it's still
tied to the disconnected DP MST connector.
Signed-off-by: Simon Ser <contact@emersion.fr>
Tested-by: Jonas Ådahl <jadahl@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20221017153150.60675-1-contact@emersion.fr
|
|
[Why]
For DCN3.2 and DCN3.21, VBIOS has switch to using v3.0 of the VRAM
info struct. We should read and override the VRAM info in driver with
values provided by VBIOS to support memory downbin cases.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
|
|
DE_CFG contains the LFENCE serializing bit, restore it on resume too.
This is relevant to older families due to the way how they do S3.
Unify and correct naming while at it.
Fixes: e4d0e84e4907 ("x86/cpu/AMD: Make LFENCE a serializing instruction")
Reported-by: Andrew Cooper <Andrew.Cooper3@citrix.com>
Reported-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
[Why]
Some DPIA AUX replies have incorrect data length from original request.
This could lead to overwriting of destination buffer if reply length is
larger, which could cause invalid access to stack since many destination
buffers are declared as local variables.
[How]
Check for invalid length from DPIA AUX replies and trigger a retry if
reply length is not the same as original request. A DRM_WARN() dmesg log
is also produced.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
|
|
TA firmware loaded on psp v13_0_10, but it is missing in modinfo.
Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
On IGT, there is a test named amd_hotplug, and when the subtest basic is
executed on DCN31, we get the following error:
[drm] *ERROR* [CRTC:71:crtc-0] flip_done timed out
[drm] *ERROR* flip_done timed out
[drm] *ERROR* [CRTC:71:crtc-0] commit wait timed out
[drm] *ERROR* flip_done timed out
[drm] *ERROR* [CONNECTOR:88:DP-1] commit wait timed out
[drm] *ERROR* flip_done timed out
[drm] *ERROR* [PLANE:59:plane-3] commit wait timed out
After enable the page flip log with the below command:
echo -n 'format "[PFLIP]" +p' > /sys/kernel/debug/dynamic_debug/control
It is possible to see that the flip was submitted, but DC never replied
back, which generates time-out issues. This is an indication that the
HUBP surface flip is missing. This commit fixes this issue by adding
hubp1_set_flip_int to DCN31.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
Since introduction of patch "Query DPIA HPD status.", link detection at
boot could be accessing DPIA AUX, which will not succeed until
DMUB outbox messaging is enabled and results in below dmesg logs:
[ 160.840227] [drm:amdgpu_dm_process_dmub_aux_transfer_sync [amdgpu]] *ERROR* wait_for_completion_timeout timeout!
[How]
Enable DMUB outbox messaging before link detection at boot time.
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.0.x
|
|
When p->gang_size equals 0, amdgpu_cs_pass1() will return directly
without freeing chunk_array, which will cause a memory leak issue,
this patch fixes it.
Fixes: 4624459c84d7 ("drm/amdgpu: add gang submit frontend v6")
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Dong Chenchen <dongchenchen2@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Samsung Galaxy Book Pro 360 (13" 2021 NP930QBD-ke1US) with codec SSID
144d:c1a6 requires the same workaround for enabling the speaker amp
like other Samsung models with ALC298 codec.
Link: https://bugzilla.opensuse.org/show_bug.cgi?id=1205100
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20221115170235.18875-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The Samsung Galaxy Book Pro seems to have the same issue as a few
other Samsung laptops, detailed in kernel bug report 207423. Sound from
headphone jack works, but not the built-in speakers.
alsa-info: http://alsa-project.org/db/?f=b40ba609dc6ae28dc84ad404a0d8a4bbcd8bea6d
Signed-off-by: Emil Flink <emil.flink@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20221115144500.7782-1-emil.flink@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
For queueing packets in XDP we want to add a new redirect map type with
support for 64-bit indexes. To prepare fore this, expand the width of the
'key' argument to the bpf_redirect_map() helper. Since BPF registers are
always 64-bit, this should be safe to do after the fact.
Acked-by: Song Liu <song@kernel.org>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20221108140601.149971-3-toke@redhat.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Move the received_rps counter value next to the other RPS-related members
in softnet_data. This closes two four-byte holes in the structure, making
room for another pointer in the first two cache lines without bumping the
xmit struct to its own line.
Acked-by: Song Liu <song@kernel.org>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20221108140601.149971-2-toke@redhat.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Fix the dodgy maths in netfs_rreq_unlock_folios(). start_page could be
inside the folio, in which case the calculation of pgpos will be come up
with a negative number (though for the moment rreq->start is rounded down
earlier and folios would have to get merged whilst locked)
Alter how this works to just frame the tracking in terms of absolute file
positions, rather than offsets from the start of the I/O request. This
simplifies the maths and makes it easier to follow.
Fix the issue by using folio_pos() and folio_size() to calculate the end
position of the page.
Fixes: 3d3c95046742 ("netfs: Provide readahead and readpage netfs helpers")
Reported-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
cc: linux-cachefs@redhat.com
cc: linux-fsdevel@vger.kernel.org
Link: https://lore.kernel.org/r/Y2SJw7w1IsIik3nb@casper.infradead.org/
Link: https://lore.kernel.org/r/166757988611.950645.7626959069846893164.stgit@warthog.procyon.org.uk/ # v2
|
|
netfslib has a number of places in which it performs iteration of an xarray
whilst being under the RCU read lock. It *should* call xas_retry() as the
first thing inside of the loop and do "continue" if it returns true in case
the xarray walker passed out a special value indicating that the walk needs
to be redone from the root[*].
Fix this by adding the missing retry checks.
[*] I wonder if this should be done inside xas_find(), xas_next_node() and
suchlike, but I'm told that's not an simple change to effect.
This can cause an oops like that below. Note the faulting address - this
is an internal value (|0x2) returned from xarray.
BUG: kernel NULL pointer dereference, address: 0000000000000402
...
RIP: 0010:netfs_rreq_unlock+0xef/0x380 [netfs]
...
Call Trace:
netfs_rreq_assess+0xa6/0x240 [netfs]
netfs_readpage+0x173/0x3b0 [netfs]
? init_wait_var_entry+0x50/0x50
filemap_read_page+0x33/0xf0
filemap_get_pages+0x2f2/0x3f0
filemap_read+0xaa/0x320
? do_filp_open+0xb2/0x150
? rmqueue+0x3be/0xe10
ceph_read_iter+0x1fe/0x680 [ceph]
? new_sync_read+0x115/0x1a0
new_sync_read+0x115/0x1a0
vfs_read+0xf3/0x180
ksys_read+0x5f/0xe0
do_syscall_64+0x38/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
Changes:
========
ver #2)
- Changed an unsigned int to a size_t to reduce the likelihood of an
overflow as per Willy's suggestion.
- Added an additional patch to fix the maths.
Fixes: 3d3c95046742 ("netfs: Provide readahead and readpage netfs helpers")
Reported-by: George Law <glaw@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com>
cc: Matthew Wilcox <willy@infradead.org>
cc: linux-cachefs@redhat.com
cc: linux-fsdevel@vger.kernel.org
Link: https://lore.kernel.org/r/166749229733.107206.17482609105741691452.stgit@warthog.procyon.org.uk/ # v1
Link: https://lore.kernel.org/r/166757987929.950645.12595273010425381286.stgit@warthog.procyon.org.uk/ # v2
|
|
Add device nodes to enable support for battery and charger status, the
ACPI platform profile, as well as internal and type-cover HID devices
(including sensors, touchpad, keyboard, and other miscellaneous devices)
on the Surface Pro 9.
This does not include support for a tablet-mode switch yet, as that is
now handled via the POS subsystem (unlike the Surface Pro 8, where it is
handled via the KIP subsystem) and therefore needs further changes.
While we're at it, also add the missing comment for the Surface Pro 8.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20221113185951.224759-2-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Currently, we check any received packet whether we have already seen it
previously, regardless of the packet type (sequenced / unsequenced). We
do this by checking the sequence number. This assumes that sequence
numbers are valid for both sequenced and unsequenced packets. However,
this assumption appears to be incorrect.
On some devices, the sequence number field of unsequenced packets (in
particular HID input events on the Surface Pro 9) is always zero. As a
result, the current retransmission check kicks in and discards all but
the first unsequenced packet, breaking (among other things) keyboard and
touchpad input.
Note that we have, so far, only seen packets being retransmitted in
sequenced communication. In particular, this happens when there is an
ACK timeout, causing the EC (or us) to re-send the packet waiting for an
ACK. Arguably, retransmission / duplication of unsequenced packets
should not be an issue as there is no logical condition (such as an ACK
timeout) to determine when a packet should be sent again.
Therefore, remove the retransmission check for unsequenced packets
entirely to resolve the issue.
Fixes: c167b9c7e3d6 ("platform/surface: Add Surface Aggregator subsystem")
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20221113185951.224759-1-luzmaximilian@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Like the Acer Switch 10 (SW5-012) and Acer Switch 10 (S1003) models
the Acer Switch V 10 (SW5-017) supports reporting SW_TABLET_MODE
through acer-wmi.
Add a DMI quirk for the SW5-017 setting force_caps to ACER_CAP_KBD_DOCK
(these devices have no other acer-wmi based functionality).
Cc: Rudolf Polzer <rpolzer@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20221111111639.35730-1-hdegoede@redhat.com
|
|
pci_get_device() will increase the reference count for the returned
pci_dev. We need to use pci_dev_put() to decrease the reference count
before asus_wmi_set_xusb2pr() returns.
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20221111100752.134311-1-wangxiongfeng2@huawei.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
btrfs_ioctl_get_subvol_info() frees the search path after the userspace
copy from the temp buffer @subvol_info. This can lead to a lock splat
warning.
Fix this by freeing the path before we copy it to userspace.
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
btrfs_ioctl_ino_to_path() frees the search path after the userspace copy
from the temp buffer @ipath->fspath. Which potentially can lead to a lock
splat warning.
Fix this by freeing the path before we copy it to userspace.
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
btrfs_ioctl_logical_to_ino() frees the search path after the userspace
copy from the temp buffer @inodes. Which potentially can lead to a lock
splat.
Fix this by freeing the path before we copy @inodes to userspace.
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
