| Age | Commit message (Collapse) | Author |
|---|
|
Use Coccinelle to convert most of the usage of INTEL_GEN() and IS_GEN()
in the display code to use DISPLAY_VER() comparisons instead. The
following semantic patch was used:
@@ expression dev_priv, E; @@
- INTEL_GEN(dev_priv) == E
+ IS_DISPLAY_VER(dev_priv, E)
@@ expression dev_priv; @@
- INTEL_GEN(dev_priv)
+ DISPLAY_VER(dev_priv)
@@ expression dev_priv; expression E; @@
- IS_GEN(dev_priv, E)
+ IS_DISPLAY_VER(dev_priv, E)
@@
expression dev_priv;
expression from, until;
@@
- IS_GEN_RANGE(dev_priv, from, until)
+ IS_DISPLAY_RANGE(dev_priv, from, until)
There are still some display-related uses of INTEL_GEN() in intel_pm.c
(watermark code) and i915_irq.c. Those will be updated separately.
v2:
- Use new IS_DISPLAY_RANGE and IS_DISPLAY_VER helpers. (Jani)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-4-matthew.d.roper@intel.com
|
|
Although we've long referred to platforms by a single "GEN" number, the
hardware teams have recommended that we stop doing this since the
various component IP blocks are going to start using independent number
schemes with varying cadence. To support this, hardware platforms a bit
down the road are going to start providing MMIO registers that the
driver can read to obtain the "graphics version," "media version," and
"display version" without needing to do a PCI ID -> platform -> version
translation.
Although our current platforms don't yet expose these registers (and the
next couple we release probably won't have them yet either), the
hardware teams would still like to see us move to this independent
numbering scheme now in preparation. For i915 that means we should try
to eliminate all usage of INTEL_GEN() throughout our code and instead
replace it with separate GRAPHICS_VER(), MEDIA_VER(), and DISPLAY_VER()
constructs in the code. For old platforms, these will all usually give
the same value for each IP block (aside from a few special cases like
GLK which we can no more accurately represent as graphics=9 +
display=10), but future platforms will have more flexibility to bump IP
version numbers independently.
The upcoming ADL-P platform will have a display version of 13 and a
graphics version of 12, so let's just the first step of breaking out
DISPLAY_VER(), but leaving the rest of INTEL_GEN() untouched for now.
For now we'll automatically derive the display version from the
platform's INTEL_GEN() value except in cases where an alternative
display version is explicitly provided in the device info structure.
We also add some helper macros IS_DISPLAY_VER(i915, ver) and
IS_DISPLAY_RANGE(i915, from, until) that match the behavior of the
existing gen-based macros. However unlike IS_GEN(), we will implement
those macros with direct comparisons rather than trying to maintain a
mask to help compiler optimization. In practice the optimization winds
up not being used in very many places (since the vast majority of our
platform checks are of the form "gen >= x") so there is pretty minimal
size reduction in the final driver binary[1]. We're also likely going
to need to extend these version numbers to non-integer major.minor
values at some point in the future, so the mask approach won't work at
all once we get to platforms like that.
[1] The results before/after the next patch in this series, which
switches our code over to the new display macros:
$ size i915.ko.{orig,new}
text data bss dec hex filename
2940291 102944 5384 3048619 2e84ab i915.ko.orig
2940723 102956 5384 3049063 2e8667 i915.ko.new
v2:
- Move version into device info's display sub-struct. (Jani)
- Add extra parentheses to macros. (Jani)
- Note the lack of genmask optimization in the display-based macros and
give size data. (Lucas)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-3-matthew.d.roper@intel.com
|
|
ILK is the only platform that we consider "gen5" and SNB is the only
platform we consider "gen6." Add an IS_SANDYBRIDGE() macro and then
replace numeric platform tests for these two generations with direct
platform tests with the following Coccinelle semantic patch:
@@ expression dev_priv; @@
- IS_GEN(dev_priv, 5)
+ IS_IRONLAKE(dev_priv)
@@ expression dev_priv; @@
- IS_GEN(dev_priv, 6)
+ IS_SANDYBRIDGE(dev_priv)
@@ expression dev_priv; @@
- IS_GEN_RANGE(dev_priv, 5, 6)
+ IS_IRONLAKE(dev_priv) || IS_SANDYBRIDGE(dev_priv)
This will simplify our upcoming patches which eliminate INTEL_GEN()
usage in the display code.
v2:
- Reverse ilk/snb order for IS_GEN_RANGE conversion. (Ville)
- Rebase + regenerate from semantic patch
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-2-matthew.d.roper@intel.com
|
|
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
This patchset fixes a logical flow in the core status, improves
shutdown support on Intel SOF platforms with an HDaudio controller and
cleans-up ElkhartLake support.
Guennadi Liakhovetski (1):
ASoC: SOF: Intel: HDA: fix core status verification
Libin Yang (5):
ASoC: SOF: Intel: TGL: fix EHL ops
ASoC: SOF: Intel: TGL: set shutdown callback to hda_dsp_shutdown
ASoC: SOF: Intel: ICL: set shutdown callback to hda_dsp_shutdown
ASoC: SOF: Intel: CNL: set shutdown callback to hda_dsp_shutdown
ASoC: SOF: Intel: APL: set shutdown callback to hda_dsp_shutdown
Pierre-Louis Bossart (2):
ASoC: SOF: core: harden shutdown helper
ASoC: SOF: Intel: move ELH chip info
sound/soc/sof/core.c | 8 +++++++-
sound/soc/sof/intel/apl.c | 3 ++-
sound/soc/sof/intel/cnl.c | 19 ++-----------------
sound/soc/sof/intel/hda-dsp.c | 21 +++++++++++++++++----
sound/soc/sof/intel/hda.h | 1 +
sound/soc/sof/intel/icl.c | 3 ++-
sound/soc/sof/intel/pci-tgl.c | 2 +-
sound/soc/sof/intel/tgl.c | 18 +++++++++++++++++-
8 files changed, 49 insertions(+), 26 deletions(-)
--
2.25.1
|
|
As explained in this discussion:
https://lore.kernel.org/netdev/20210117193009.io3nungdwuzmo5f7@skbuf/
the switchdev notifiers for FDB entries managed to have a zero-day bug.
The bridge would not say that this entry is local:
ip link add br0 type bridge
ip link set swp0 master br0
bridge fdb add dev swp0 00:01:02:03:04:05 master local
and the switchdev driver would be more than happy to offload it as a
normal static FDB entry. This is despite the fact that 'local' and
non-'local' entries have completely opposite directions: a local entry
is locally terminated and not forwarded, whereas a static entry is
forwarded and not locally terminated. So, for example, DSA would install
this entry on swp0 instead of installing it on the CPU port as it should.
There is an even sadder part, which is that the 'local' flag is implicit
if 'static' is not specified, meaning that this command produces the
same result of adding a 'local' entry:
bridge fdb add dev swp0 00:01:02:03:04:05 master
I've updated the man pages for 'bridge', and after reading it now, it
should be pretty clear to any user that the commands above were broken
and should have never resulted in the 00:01:02:03:04:05 address being
forwarded (this behavior is coherent with non-switchdev interfaces):
https://patchwork.kernel.org/project/netdevbpf/cover/20210211104502.2081443-1-olteanv@gmail.com/
If you're a user reading this and this is what you want, just use:
bridge fdb add dev swp0 00:01:02:03:04:05 master static
Because switchdev should have given drivers the means from day one to
classify FDB entries as local/non-local, but didn't, it means that all
drivers are currently broken. So we can just as well omit the switchdev
notifications for local FDB entries, which is exactly what this patch
does to close the bug in stable trees. For further development work
where drivers might want to trap the local FDB entries to the host, we
can add a 'bool is_local' to br_switchdev_fdb_call_notifiers(), and
selectively make drivers act upon that bit, while all the others ignore
those entries if the 'is_local' bit is set.
Fixes: 6b26b51b1d13 ("net: bridge: Add support for notifying devices about FDB add/del")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Invalid detection works with two distinct moments: act_ct tries to find
a conntrack entry and set post_ct true, indicating that that was
attempted. Then, when flow dissector tries to dissect CT info and no
entry is there, it knows that it was tried and no entry was found, and
synthesizes/sets
key->ct_state = TCA_FLOWER_KEY_CT_FLAGS_TRACKED |
TCA_FLOWER_KEY_CT_FLAGS_INVALID;
mimicing what OVS does.
OVS has this a bit more streamlined, as it recomputes the key after
trying to find a conntrack entry for it.
Issue here is, when we have 'tc action ct clear', it didn't clear
post_ct, causing a subsequent match on 'ct_state -trk' to fail, due to
the above. The fix, thus, is to clear it.
Reproducer rules:
tc filter add dev enp130s0f0np0_0 ingress prio 1 chain 0 \
protocol ip flower ip_proto tcp ct_state -trk \
action ct zone 1 pipe \
action goto chain 2
tc filter add dev enp130s0f0np0_0 ingress prio 1 chain 2 \
protocol ip flower \
action ct clear pipe \
action goto chain 4
tc filter add dev enp130s0f0np0_0 ingress prio 1 chain 4 \
protocol ip flower ct_state -trk \
action mirred egress redirect dev enp130s0f1np1_0
With the fix, the 3rd rule matches, like it does with OVS kernel
datapath.
Fixes: 7baf2429a1a9 ("net/sched: cls_flower add CT_FLAGS_INVALID flag support")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Open-coding this function meant it missed out on the recent bugfix
for waiters being woken by a delayed wake event from a previous
instantiation of the page[1].
[DH: Changed the patch to use vmf->page rather than variable page which
doesn't exist yet upstream]
Fixes: 1cf7a1518aef ("afs: Implement shared-writeable mmap")
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: kafs-testing@auristor.com
cc: linux-afs@lists.infradead.org
cc: linux-mm@kvack.org
Link: https://lore.kernel.org/r/20210320054104.1300774-4-willy@infradead.org
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=c2407cf7d22d0c0d94cf20342b3b8f06f1d904e7 [1]
|
|
This is the killable version of wait_on_page_writeback.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: kafs-testing@auristor.com
cc: linux-afs@lists.infradead.org
cc: linux-mm@kvack.org
Link: https://lore.kernel.org/r/20210320054104.1300774-3-willy@infradead.org
|
|
Cachefiles was relying on wait_page_key and wait_bit_key being the
same layout, which is fragile. Now that wait_page_key is exposed in
the pagemap.h header, we can remove that fragility
A comment on the need to maintain structure layout equivalence was added by
Linus[1] and that is no longer applicable.
Fixes: 62906027091f ("mm: add PageWaiters indicating tasks are waiting for a page bit")
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: kafs-testing@auristor.com
cc: linux-cachefs@redhat.com
cc: linux-mm@kvack.org
Link: https://lore.kernel.org/r/20210320054104.1300774-2-willy@infradead.org/
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=3510ca20ece0150af6b10c77a74ff1b5c198e3e2 [1]
|
|
Due to a HW limitation, the Latency Tolerance Reporting (LTR) value
programmed in the Tiger Lake GBE controller is not large enough to allow
the platform to enter Package C10, which in turn prevents the platform from
achieving its low power target during suspend-to-idle. Ignore the GBE LTR
value on Tiger Lake. LTR ignore functionality is currently performed solely
by a debugfs write call. Split out the LTR code into its own function that
can be called by both the debugfs writer and by this work around.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Sasha Neftin <sasha.neftin@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Reviewed-by: Rajneesh Bhardwaj <irenic.rajneesh@gmail.com>
Link: https://lore.kernel.org/r/20210319201844.3305399-2-david.e.box@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The intel_pmc_core driver is mostly used as a debugging driver for Intel
platforms that support SLPS0 (S0ix). But the driver may also be used to
communicate actions to the PMC in order to ensure transition to SLPS0 on
some systems and architectures. As such the driver should be built on all
platforms it supports. Indicate this in the Kconfig. Also update the list
of supported features.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Suggested-by: Mario Limonciello <mario.limonciello@dell.com>
Link: https://lore.kernel.org/r/20210319201844.3305399-1-david.e.box@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Fixes off-by-one bugs in the macro assignments for the crashlog control
bits. Was initially tested on emulation but bug revealed after testing on
silicon.
Fixes: 5ef9998c96b0 ("platform/x86: Intel PMT Crashlog capability driver")
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20210317024455.3071477-2-david.e.box@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Initialize the struct resource in intel_pmt_dev_register to zero to avoid a
fault should the char *name field be non-zero.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20210317024455.3071477-1-david.e.box@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The debugfs directory '/sys/kernel/debug/energy_model' is needed before
the Energy Model registration can happen. With the recent change in
debugfs subsystem it's not allowed to create this directory at early
stage (core_initcall). Thus creating this directory would fail.
Postpone the creation of the EM debug dir to later stage: fs_initcall.
It should be safe since all clients: CPUFreq drivers, Devfreq drivers
will be initialized in later stages.
The custom debug log below prints the time of creation the EM debug dir
at fs_initcall and successful registration of EMs at later stages.
[ 1.505717] energy_model: creating rootdir
[ 3.698307] cpu cpu0: EM: created perf domain
[ 3.709022] cpu cpu1: EM: created perf domain
Fixes: 56348560d495 ("debugfs: do not attempt to create a new file before the filesystem is initalized")
Reported-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
analogix_dp_probe()
Just another drive-by fix I noticed while going through the tree to cleanup
DP aux adapter registration - make sure we unregister the DP AUX dev if
analogix_dp_probe() fails.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210219215326.2227596-14-lyude@redhat.com
|
|
Another drive-by fix I found when fixing DP AUX adapter across the kernel
tree - make sure we don't leak resources (and by proxy-AUX adapters) on
failures in anx6345_bridge_attach() by unrolling on errors.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210219215326.2227596-13-lyude@redhat.com
|
|
registration
Another case of linking an encoder to a connector after the connector's
been registered. The proper place to do this is before connector
registration, so let's fix that.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210219215326.2227596-12-lyude@redhat.com
|
|
Another driver I found that seems to forget to unregister it's DP AUX
device. Let's fix this by adding anx6345_bridge_detach().
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210219215326.2227596-11-lyude@redhat.com
|
|
Just another issue I noticed while correcting usages of
drm_dp_aux_init()/drm_dp_aux_register() around the tree. If any of the
steps in anx78xx_bridge_attach() fail, we end up leaking resources. So,
let's fix that (and fix leaking a DP AUX adapter in the process) by
unrolling on errors.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210219215326.2227596-10-lyude@redhat.com
|
|
Since encoder mappings for connectors are exposed to userspace, we should
be attaching the encoder before exposing the connector to userspace. Just a
drive-by fix for an issue I noticed while fixing up usages of
drm_dp_aux_init()/drm_dp_aux_register() across the tree.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210219215326.2227596-9-lyude@redhat.com
|
|
Surprisingly, this bridge actually registers it's AUX adapter at the
correct time already. Nice job! However, it does forget to actually
unregister the AUX adapter, so let's add a bridge function to handle that.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210219215326.2227596-8-lyude@redhat.com
|
|
Since we're about to add a back-pointer to drm_dev in drm_dp_aux, let's
move the AUX adapter registration to the first point where we know which
DRM device we'll be working with - when the drm_bridge is attached.
Likewise, we unregister the AUX adapter on bridge detachment by adding a
ti_sn_bridge_detach() callback.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210219215326.2227596-7-lyude@redhat.com
|
|
Since this is a bridge, we don't start out with a respective DRM device.
Likewise this means we don't have a connector, which also means that we
should be following drm_dp_aux_register()'s documentation advice and not
call drm_dp_aux_register() until we have a matching connector. Instead,
call drm_dp_aux_init() in tc_probe() and wait until tc_bridge_attach() to
register our AUX channel. We also add tc_bridge_detach() to handle
unregistering the AUX adapter once the bridge has been disconnected.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210219215326.2227596-5-lyude@redhat.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull KUnit fixes from Shuah Khan:
"Two fixes to the kunit tool from David Gow"
* tag 'linux-kselftest-kunit-fixes-5.12-rc5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: tool: Disable PAGE_POISONING under --alltests
kunit: tool: Fix a python tuple typing error
|
|
The input MCLK is 12.288MHz, the desired output sysclk is 11.2896MHz
and sample rate is 44100Hz, with the configuration pllprescale=2,
postscale=sysclkdiv=1, some chip may have wrong bclk
and lrclk output with pll enabled in master mode, but with the
configuration pllprescale=1, postscale=2, the output clock is correct.
>From Datasheet, the PLL performs best when f2 is between
90MHz and 100MHz when the desired sysclk output is 11.2896MHz
or 12.288MHz, so sysclkdiv = 2 (f2/8) is the best choice.
So search available sysclk_divs from 2 to 1 other than from 1 to 2.
Fixes: 84fdc00d519f ("ASoC: codec: wm9860: Refactor PLL out freq search")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1616150926-22892-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ELH is a derivative of TGL, so it should be exposed in tgl.c for
consistency.
No functional change.
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210322163728.16616-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to hardware spec and PMC FW requirement, the DSP must be
in D3 state before entering S5. Set shutdown call to hda_dsp_shutdown.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210322163728.16616-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to hardware spec and PMC FW requirement, the DSP must be
in D3 state before entering S5. Set shutdown call to hda_dsp_shutdown.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210322163728.16616-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to hardware spec and PMC FW requirement, the DSP must be
in D3 state before entering S5. Set shutdown call to hda_dsp_shutdown.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210322163728.16616-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to hardware spec and PMC FW requirement, the DSP must be
in D3 state before entering S5. Define the shutdown function to use
snd_sof_suspend as shutdown callback to make sure DSP is in D3 state.
Fixes: 44a4cfad8d78 ("ASoC: SOF: Intel: tgl: do thorough remove at .shutdown() callback")
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pan Xiuli <xiuli.pan@linux.intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210322163728.16616-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
EHL is derived from TGL, not CNL, so we shall use the TGL ops.
Fixes: 8d4ba1be3d22 ("ASoC: SOF: pci: split PCI into different drivers")
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210322163728.16616-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the probe is handled in a workqueue, we must use
cancel_work_sync() in the shutdown helper to avoid possible race
conditions.
We must also take care of possible errors happening in a probe
workqueue or during pm_runtime resume (called e.g. before shutdown for
PCI devices). We should really only try to access hardware registers
and initiate IPCs if the DSP is fully booted.
Fixes: daff7f1478e12 ("ASoC: SOF: add snd_sof_device_shutdown() helper for shutdown")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Link: https://lore.kernel.org/r/20210322163728.16616-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When checking for enabled cores it isn't enough to check that
some of the requested cores are running, we have to check that
all of them are.
Fixes: 747503b1813a ("ASoC: SOF: Intel: Add Intel specific HDA DSP HW operations")
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210322163728.16616-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When a stacked block device inserts a request into another block device
using blk_insert_cloned_request, the request's nr_phys_segments field gets
recalculated by a call to blk_recalc_rq_segments in
blk_cloned_rq_check_limits. But blk_recalc_rq_segments does not know how to
handle multi-segment discards. For disk types which can handle
multi-segment discards like nvme, this results in discard requests which
claim a single segment when it should report several, triggering a warning
in nvme and causing nvme to fail the discard from the invalid state.
WARNING: CPU: 5 PID: 191 at drivers/nvme/host/core.c:700 nvme_setup_discard+0x170/0x1e0 [nvme_core]
...
nvme_setup_cmd+0x217/0x270 [nvme_core]
nvme_loop_queue_rq+0x51/0x1b0 [nvme_loop]
__blk_mq_try_issue_directly+0xe7/0x1b0
blk_mq_request_issue_directly+0x41/0x70
? blk_account_io_start+0x40/0x50
dm_mq_queue_rq+0x200/0x3e0
blk_mq_dispatch_rq_list+0x10a/0x7d0
? __sbitmap_queue_get+0x25/0x90
? elv_rb_del+0x1f/0x30
? deadline_remove_request+0x55/0xb0
? dd_dispatch_request+0x181/0x210
__blk_mq_do_dispatch_sched+0x144/0x290
? bio_attempt_discard_merge+0x134/0x1f0
__blk_mq_sched_dispatch_requests+0x129/0x180
blk_mq_sched_dispatch_requests+0x30/0x60
__blk_mq_run_hw_queue+0x47/0xe0
__blk_mq_delay_run_hw_queue+0x15b/0x170
blk_mq_sched_insert_requests+0x68/0xe0
blk_mq_flush_plug_list+0xf0/0x170
blk_finish_plug+0x36/0x50
xlog_cil_committed+0x19f/0x290 [xfs]
xlog_cil_process_committed+0x57/0x80 [xfs]
xlog_state_do_callback+0x1e0/0x2a0 [xfs]
xlog_ioend_work+0x2f/0x80 [xfs]
process_one_work+0x1b6/0x350
worker_thread+0x53/0x3e0
? process_one_work+0x350/0x350
kthread+0x11b/0x140
? __kthread_bind_mask+0x60/0x60
ret_from_fork+0x22/0x30
This patch fixes blk_recalc_rq_segments to be aware of devices which can
have multi-segment discards. It calculates the correct discard segment
count by counting the number of bio as each discard bio is considered its
own segment.
Fixes: 1e739730c5b9 ("block: optionally merge discontiguous discard bios into a single request")
Signed-off-by: David Jeffery <djeffery@redhat.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Link: https://lore.kernel.org/r/20210211143807.GA115624@redhat
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The GD_NEED_PART_SCAN is set by bdev_check_media_change to initiate
a partition scan while removing a block device. It should be cleared
after blk_drop_paritions because blk_drop_paritions could return
-EBUSY and then the consequence __blkdev_get has no chance to do
delete_partition if GD_NEED_PART_SCAN already cleared.
It causes some problems on some card readers. Ex. Realtek card
reader 0bda:0328 and 0bda:0158. The device node of the partition
will not disappear after the memory card removed. Thus the user
applications can not update the device mapping correctly.
BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1920874
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210323085219.24428-1-chris.chiu@canonical.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The new Ubuntu GCC packages turn on -fcf-protection globally,
which causes a build failure in the x86 realmode code:
cc1: error: ‘-fcf-protection’ is not compatible with this target
Turn it off explicitly on compilers that understand this option.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20210323124846.1584944-1-arnd@kernel.org
|
|
add null-check on function pointer before dereference on ops->cursor
Reported-by: syzbot+b67aaae8d3a927f68d20@syzkaller.appspotmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Du Cheng <ducheng2@gmail.com>
Link: https://lore.kernel.org/r/20210312081421.452405-1-ducheng2@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allow map and unmap of the client dma buffer only when the client is not
connected. The functions return -EPROTO if the client is already connected.
This is to fix the race when traffic may start or stop when buffer
is not available.
Cc: <stable@vger.kernel.org> #v5.11+
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20210318055959.305627-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Linux-phy subsystem gained mailing list and a patchwork instance. Add the
details to MAINTAINERS file
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210226111233.2601369-1-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When retrying a deferred probe, any old defer reason string should be
discarded. Otherwise, if the probe is deferred again at a different spot,
but without setting a message, the now incorrect probe reason will remain.
This was observed with the i.MX I2C driver, which ultimately failed
to probe due to lack of the GPIO driver. The probe defer for GPIO
doesn't record a message, but a previous probe defer to clock_get did.
This had the effect that /sys/kernel/debug/devices_deferred listed
a misleading probe deferral reason.
Cc: stable <stable@vger.kernel.org>
Fixes: d090b70ede02 ("driver core: add deferring probe reason to devices_deferred property")
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20210319110459.19966-1-a.fatoum@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On some Intel platforms, audio noise can be detected due to
high pcie speed switch latency.
This patch leaverages ppfeaturemask to fix to the highest pcie
speed then disable pcie switching.
v2:
coding style fix
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
The "u16 CcxRmState[2];" array field in struct "rtllib_network" has 4
bytes in total while the operations performed on this array through-out
the code base are only 2 bytes.
The "CcxRmState" field is fed only 2 bytes of data using memcpy():
(In rtllib_rx.c:1972)
memcpy(network->CcxRmState, &info_element->data[4], 2)
With "info_element->data[]" being a u8 array, if 2 bytes are written
into "CcxRmState" (whose one element is u16 size), then the 2 u8
elements from "data[]" gets squashed and written into the first element
("CcxRmState[0]") while the second element ("CcxRmState[1]") is never
fed with any data.
Same in file rtllib_rx.c:2522:
memcpy(dst->CcxRmState, src->CcxRmState, 2);
The above line duplicates "src" data to "dst" but only writes 2 bytes
(and not 4, which is the actual size). Again, only 1st element gets the
value while the 2nd element remains uninitialized.
This later makes operations done with CcxRmState unpredictable in the
following lines as the 1st element is having a squashed number while the
2nd element is having an uninitialized random number.
rtllib_rx.c:1973: if (network->CcxRmState[0] != 0)
rtllib_rx.c:1977: network->MBssidMask = network->CcxRmState[1] & 0x07;
network->MBssidMask is also of type u8 and not u16.
Fix this by changing the type of "CcxRmState" from u16 to u8 so that the
data written into this array and read from it make sense and are not
random values.
NOTE: The wrong initialization of "CcxRmState" can be seen in the
following commit:
commit ecdfa44610fa ("Staging: add Realtek 8192 PCI wireless driver")
The above commit created a file `rtl8192e/ieee80211.h` which used to
have the faulty line. The file has been deleted (or possibly renamed)
with the contents copied in to a new file `rtl8192e/rtllib.h` along with
additional code in the commit 94a799425eee (tagged in Fixes).
Fixes: 94a799425eee ("From: wlanfae <wlanfae@realtek.com> [PATCH 1/8] rtl8192e: Import new version of driver from realtek")
Cc: stable@vger.kernel.org
Signed-off-by: Atul Gopinathan <atulgopinathan@gmail.com>
Link: https://lore.kernel.org/r/20210323113413.29179-2-atulgopinathan@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The variable "info_element" is of the following type:
struct rtllib_info_element *info_element
defined in drivers/staging/rtl8192e/rtllib.h:
struct rtllib_info_element {
u8 id;
u8 len;
u8 data[];
} __packed;
The "len" field defines the size of the "data[]" array. The code is
supposed to check if "info_element->len" is greater than 4 and later
equal to 6. If this is satisfied then, the last two bytes (the 4th and
5th element of u8 "data[]" array) are copied into "network->CcxRmState".
Right now the code uses "memcpy()" with the source as "&info_element[4]"
which would copy in wrong and unintended information. The struct
"rtllib_info_element" has a size of 2 bytes for "id" and "len",
therefore indexing will be done in interval of 2 bytes. So,
"info_element[4]" would point to data which is beyond the memory
allocated for this pointer (that is, at x+8, while "info_element" has
been allocated only from x to x+7 (2 + 6 => 8 bytes)).
This patch rectifies this error by using "&info_element->data[4]" which
correctly copies the last two bytes of "data[]".
NOTE: The faulty line of code came from the following commit:
commit ecdfa44610fa ("Staging: add Realtek 8192 PCI wireless driver")
The above commit created the file `rtl8192e/ieee80211/ieee80211_rx.c`
which had the faulty line of code. This file has been deleted (or
possibly renamed) with the contents copied in to a new file
`rtl8192e/rtllib_rx.c` along with additional code in the commit
94a799425eee (tagged in Fixes).
Fixes: 94a799425eee ("From: wlanfae <wlanfae@realtek.com> [PATCH 1/8] rtl8192e: Import new version of driver from realtek")
Cc: stable@vger.kernel.org
Signed-off-by: Atul Gopinathan <atulgopinathan@gmail.com>
Link: https://lore.kernel.org/r/20210323113413.29179-1-atulgopinathan@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This LTE modem (M.2 card) has a bug in its power management:
there is some kind of race condition for U3 wake-up between the host and
the device. The modem firmware sometimes crashes/locks when both events
happen at the same time and the modem fully drops off the USB bus (and
sometimes re-enumerates, sometimes just gets stuck until the next
reboot).
Tested with the modem wired to the XHCI controller on an AMD 3015Ce
platform. Without the patch, the modem dropped of the USB bus 5 times in
3 days. With the quirk, it stayed connected for a week while the
'runtime_suspended_time' counter incremented as excepted.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Link: https://lore.kernel.org/r/20210319124802.2315195-1-vpalatin@chromium.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Do not log the successful-probe message until the tty device has been
registered.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-9-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to always claim the data interface and bail out if binding
fails.
Note that the driver had a check to verify that the data interface was
not already bound to a driver but would not detect other failures (e.g.
if the interface was not authorised).
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-8-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use negation consistently throughout the driver for NULL checks.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-7-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Name the probe error labels after what they do rather than using
sequence numbers which is harder to review and maintain (e.g. may
require renaming unrelated labels when a label is added or removed).
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-6-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There's no need to clear the interface driver data on failed probe (and
driver core will clear it anyway).
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The interface driver data has already been set by
usb_driver_claim_interface() so drop the redundant subsequent
assignment.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
