| Age | Commit message (Collapse) | Author |
|---|
|
JMS_MAX_SIZE is the ethernet frame length, not the MTU, which is payload
without ethernet headers.
According to the datasheets maximum supported frame length for most
gigabyte swithes is 9720 bytes, so convert that to the expected MTU when
using VLAN tagged frames.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
JMS_MIN_SIZE is the full ethernet frame length, while mtu is just the
data payload size. Comparing these two meant that mtus between 1500 and
1518 did not trigger enabling jumbo frames.
So instead compare the set mtu ETH_DATA_LEN, which is equal to
JMS_MIN_SIZE - ETH_HLEN - ETH_FCS_LEN;
Also do a check that the requested mtu is actually greater than the
minimum length, else we do not need to enable jumbo frames.
In practice this only introduced a very small range of mtus that did not
work properly. Newer chips allow 2000 byte large frames by default, and
older chips allow 1536 bytes long, which is equivalent to an mtu of
1514. So effectivly only mtus of 1515~1517 were broken.
Fixes: 6ae5834b983a ("net: dsa: b53: add MTU configuration support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Nicolas Pitre says:
====================
fix ti-am65-cpsw-nuss module removal
Fix issues preventing rmmod of ti-am65-cpsw-nuss from working properly.
v3:
- more patch submission minutiae
v2: https://lore.kernel.org/netdev/20241003172105.2712027-2-nico@fluxnic.net/T/
- conform to netdev patch submission customs
- address patch review trivias
v1: https://lore.kernel.org/netdev/20240927025301.1312590-2-nico@fluxnic.net/T/
====================
Link: https://patch.msgid.link/20241004041218.2809774-1-nico@fluxnic.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Usage of devm_alloc_etherdev_mqs() conflicts with
am65_cpsw_nuss_cleanup_ndev() as the same struct net_device instances
get unregistered twice. Switch to alloc_etherdev_mqs() and make sure
am65_cpsw_nuss_cleanup_ndev() unregisters and frees those net_device
instances properly.
With this, it is finally possible to rmmod the driver without oopsing
the kernel.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Roger Quadros <roger@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In am65_cpsw_nuss_remove(), move the call to am65_cpsw_unregister_devlink()
after am65_cpsw_nuss_cleanup_ndev() to avoid triggering the
WARN_ON(devlink_port->type != DEVLINK_PORT_TYPE_NOTSET) in
devl_port_unregister(). Makes it coherent with usage in
m65_cpsw_nuss_register_ndevs()'s cleanup path.
Fixes: 58356eb31d60 ("net: ti: am65-cpsw-nuss: Add devlink support")
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Move the tx cpu dma ring index update out of transmit loop of
airoha_dev_xmit routine in order to not start transmitting the packet
before it is fully DMA mapped (e.g. fragmented skbs).
Fixes: 23020f049327 ("net: airoha: Introduce ethernet support for EN7581 SoC")
Reported-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241004-airoha-eth-7581-mapping-fix-v1-1-8e4279ab1812@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit c938ab4da0eb ("net: phy: Manual remove LEDs to ensure correct
ordering") correctly fixed a problem with using devm_ but missed
removing the LED entry from the LEDs list.
This cause kernel panic on specific scenario where the port for the PHY
is torn down and up and the kmod for the PHY is removed.
On setting the port down the first time, the assosiacted LEDs are
correctly unregistered. The associated kmod for the PHY is now removed.
The kmod is now added again and the port is now put up, the associated LED
are registered again.
On putting the port down again for the second time after these step, the
LED list now have 4 elements. With the first 2 already unregistered
previously and the 2 new one registered again.
This cause a kernel panic as the first 2 element should have been
removed.
Fix this by correctly removing the element when LED is unregistered.
Reported-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Cc: stable@vger.kernel.org
Fixes: c938ab4da0eb ("net: phy: Manual remove LEDs to ensure correct ordering")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241004182759.14032-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- RFCOMM: FIX possible deadlock in rfcomm_sk_state_change
- hci_conn: Fix UAF in hci_enhanced_setup_sync
- btusb: Don't fail external suspend requests
* tag 'for-net-2024-10-04' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: btusb: Don't fail external suspend requests
Bluetooth: hci_conn: Fix UAF in hci_enhanced_setup_sync
Bluetooth: RFCOMM: FIX possible deadlock in rfcomm_sk_state_change
====================
Link: https://patch.msgid.link/20241004210124.4010321-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
adin1110_read_fifo()
If 'frame_size' is too small or if 'round_len' is an error code, it is
likely that an error code should be returned to the caller.
Actually, 'ret' is likely to be 0, so if one of these sanity checks fails,
'success' is returned.
Return -EINVAL instead.
Fixes: bc93e19d088b ("net: ethernet: adi: Add ADIN1110 support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/8ff73b40f50d8fa994a454911b66adebce8da266.1727981562.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit b514c47ebf41a6536551ed28a05758036e6eca7c.
The commit describes that we don't have to sync the page when
recycling, and it tries to optimize that case. But we do need
to sync after allocation. Recycling side should be changed to
pass the right sync size instead.
Fixes: b514c47ebf41 ("net: stmmac: set PP_FLAG_DMA_SYNC_DEV only if XDP is enabled")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/20241004070846.2502e9ea@kernel.org
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Furong Xu <0x1207@gmail.com>
Link: https://patch.msgid.link/20241004142115.910876-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Accessing device registers seems to be not reliable, the chip
revision is sometimes detected wrongly (0 instead of expected 1).
Ensure that the chip reset is performed via reset GPIO and then
wait for 'Device Ready' status in HW_CFG register before doing
any register initializations.
Cc: stable@vger.kernel.org
Fixes: a1292595e006 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
[alex: reworked using read_poll_timeout()]
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20241004113655.3436296-1-alexander.sverdlin@siemens.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We have recently noticed the exact same KASAN splat as in commit
6cd4a78d962b ("net: do not leave a dangling sk pointer, when socket
creation fails"). The problem is that commit did not fully address the
problem, as some pf->create implementations do not use sk_common_release
in their error paths.
For example, we can use the same reproducer as in the above commit, but
changing ping to arping. arping uses AF_PACKET socket and if packet_create
fails, it will just sk_free the allocated sk object.
While we could chase all the pf->create implementations and make sure they
NULL the freed sk object on error from the socket, we can't guarantee
future protocols will not make the same mistake.
So it is easier to just explicitly NULL the sk pointer upon return from
pf->create in __sock_create. We do know that pf->create always releases the
allocated sk object on error, so if the pointer is not NULL, it is
definitely dangling.
Fixes: 6cd4a78d962b ("net: do not leave a dangling sk pointer, when socket creation fails")
Signed-off-by: Ignat Korchagin <ignat@cloudflare.com>
Cc: stable@vger.kernel.org
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241003170151.69445-1-ignat@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When adding a delayed ref head, at delayed-ref.c:add_delayed_ref_head(),
if we fail to insert the qgroup record we don't error out, we ignore it.
In fact we treat it as if there was no error and there was already an
existing record - we don't distinguish between the cases where
btrfs_qgroup_trace_extent_nolock() returns 1, meaning a record already
existed and we can free the given record, and the case where it returns
a negative error value, meaning the insertion into the xarray that is
used to track records failed.
Effectively we end up ignoring that we are lacking qgroup record in the
dirty extents xarray, resulting in incorrect qgroup accounting.
Fix this by checking for errors and return them to the callers.
Fixes: 3cce39a8ca4e ("btrfs: qgroup: use xarray to track dirty extents in transaction")
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
There are reports that system cannot suspend due to running trim because
the task responsible for trimming the device isn't able to finish in
time, especially since we have a free extent discarding phase, which can
trim a lot of unallocated space. There are no limits on the trim size
(unlike the block group part).
Since trime isn't a critical call it can be interrupted at any time,
in such cases we stop the trim, report the amount of discarded bytes and
return an error.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219180
Link: https://bugzilla.suse.com/show_bug.cgi?id=1229737
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Luca Stefani <luca.stefani.ge1@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Per Qu Wenruo in case we have a very large disk, e.g. 8TiB device,
mostly empty although we will do the split according to our super block
locations, the last super block ends at 256G, we can submit a huge
discard for the range [256G, 8T), causing a large delay.
Split the space left to discard based on BTRFS_MAX_DISCARD_CHUNK_SIZE in
preparation of introduction of cancellation points to trim. The value
of the chunk size is arbitrary, it can be higher or derived from actual
device capabilities but we can't easily read that using
bio_discard_limit().
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219180
Link: https://bugzilla.suse.com/show_bug.cgi?id=1229737
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Luca Stefani <luca.stefani.ge1@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
scx_qmap and other schedulers in the SCX repo are using SCX_ENQ_WAKEUP to
tell whether ops.select_cpu() was called. This is incorrect as
ops.select_cpu() can be skipped in the wakeup path and leads to e.g.
incorrectly skipping direct dispatch for tasks that are bound to a single
CPU.
sched core has been updated to specify ENQUEUE_RQ_SELECTED if
->select_task_rq() was called. Map it to SCX_ENQ_CPU_SELECTED and update
scx_qmap to test it instead of SCX_ENQ_WAKEUP.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Vernet <void@manifault.com>
Cc: Daniel Hodges <hodges.daniel.scott@gmail.com>
Cc: Changwoo Min <multics69@gmail.com>
Cc: Andrea Righi <andrea.righi@linux.dev>
Cc: Dan Schatzberg <schatzberg.dan@gmail.com>
|
|
was called
During ttwu, ->select_task_rq() can be skipped if only one CPU is allowed or
migration is disabled. sched_ext schedulers may perform operations such as
direct dispatch from ->select_task_rq() path and it is useful for them to
know whether ->select_task_rq() was skipped in the ->enqueue_task() path.
Currently, sched_ext schedulers are using ENQUEUE_WAKEUP for this purpose
and end up assuming incorrectly that ->select_task_rq() was called for tasks
that are bound to a single CPU or migration disabled.
Make select_task_rq() indicate whether ->select_task_rq() was called by
setting WF_RQ_SELECTED in *wake_flags and make ttwu_do_activate() map that
to ENQUEUE_RQ_SELECTED for ->enqueue_task().
This will be used by sched_ext to fix ->select_task_rq() skip detection.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Vernet <void@manifault.com>
|
|
value
This will be used to allow select_task_rq() to indicate whether
->select_task_rq() was called by modifying *wake_flags.
This makes try_to_wake_up() call all functions that take wake_flags with
WF_TTWU set. Previously, only select_task_rq() was. Using the same flags is
more consistent, and, as the flag is only tested by ->select_task_rq()
implementations, it doesn't cause any behavior differences.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Vernet <void@manifault.com>
|
|
Pull virtio fixes from Michael Tsirkin:
"Several small bugfixes all over the place.
Most notably, fixes the vsock allocation with GFP_KERNEL in atomic
context, which has been triggering warnings for lots of testers"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost/scsi: null-ptr-dereference in vhost_scsi_get_req()
vsock/virtio: use GFP_ATOMIC under RCU read lock
virtio_console: fix misc probe bugs
virtio_ring: tag event_triggered as racy for KCSAN
vdpa/octeon_ep: Fix format specifier for pointers in debug messages
|
|
Since commit 3f8ca2e115e5 ("vhost/scsi: Extract common handling code
from control queue handler") a null pointer dereference bug can be
triggered when guest sends an SCSI AN request.
In vhost_scsi_ctl_handle_vq(), `vc.target` is assigned with
`&v_req.tmf.lun[1]` within a switch-case block and is then passed to
vhost_scsi_get_req() which extracts `vc->req` and `tpg`. However, for
a `VIRTIO_SCSI_T_AN_*` request, tpg is not required, so `vc.target` is
set to NULL in this branch. Later, in vhost_scsi_get_req(),
`vc->target` is dereferenced without being checked, leading to a null
pointer dereference bug. This bug can be triggered from guest.
When this bug occurs, the vhost_worker process is killed while holding
`vq->mutex` and the corresponding tpg will remain occupied
indefinitely.
Below is the KASAN report:
Oops: general protection fault, probably for non-canonical address
0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 1 PID: 840 Comm: poc Not tainted 6.10.0+ #1
Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS
1.16.3-debian-1.16.3-2 04/01/2014
RIP: 0010:vhost_scsi_get_req+0x165/0x3a0
Code: 00 fc ff df 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 2b 02 00 00
48 b8 00 00 00 00 00 fc ff df 4d 8b 65 30 4c 89 e2 48 c1 ea 03 <0f> b6
04 02 4c 89 e2 83 e2 07 38 d0 7f 08 84 c0 0f 85 be 01 00 00
RSP: 0018:ffff888017affb50 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffff88801b000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff888017affcb8
RBP: ffff888017affb80 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: ffff888017affc88 R14: ffff888017affd1c R15: ffff888017993000
FS: 000055556e076500(0000) GS:ffff88806b100000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000200027c0 CR3: 0000000010ed0004 CR4: 0000000000370ef0
Call Trace:
<TASK>
? show_regs+0x86/0xa0
? die_addr+0x4b/0xd0
? exc_general_protection+0x163/0x260
? asm_exc_general_protection+0x27/0x30
? vhost_scsi_get_req+0x165/0x3a0
vhost_scsi_ctl_handle_vq+0x2a4/0xca0
? __pfx_vhost_scsi_ctl_handle_vq+0x10/0x10
? __switch_to+0x721/0xeb0
? __schedule+0xda5/0x5710
? __kasan_check_write+0x14/0x30
? _raw_spin_lock+0x82/0xf0
vhost_scsi_ctl_handle_kick+0x52/0x90
vhost_run_work_list+0x134/0x1b0
vhost_task_fn+0x121/0x350
...
</TASK>
---[ end trace 0000000000000000 ]---
Let's add a check in vhost_scsi_get_req.
Fixes: 3f8ca2e115e5 ("vhost/scsi: Extract common handling code from control queue handler")
Signed-off-by: Haoran Zhang <wh1sper@zju.edu.cn>
[whitespace fixes]
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <b26d7ddd-b098-4361-88f8-17ca7f90adf7@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
virtio_transport_send_pkt in now called on transport fast path,
under RCU read lock. In that case, we have a bug: virtio_add_sgs
is called with GFP_KERNEL, and might sleep.
Pass the gfp flags as an argument, and use GFP_ATOMIC on
the fast path.
Link: https://lore.kernel.org/all/hfcr2aget2zojmqpr4uhlzvnep4vgskblx5b6xf2ddosbsrke7@nt34bxgp7j2x
Fixes: efcd71af38be ("vsock/virtio: avoid queuing packets when intermediate queue is empty")
Reported-by: Christian Brauner <brauner@kernel.org>
Cc: Stefano Garzarella <sgarzare@redhat.com>
Cc: Luigi Leonardi <luigi.leonardi@outlook.com>
Message-ID: <3fbfb6e871f625f89eb578c7228e127437b1975a.1727876449.git.mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@amd.com>
Reviewed-by: Christian Brauner <brauner@kernel.org>
Reviewed-by: Luigi Leonardi <luigi.leonardi@outlook.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
|
|
The background blockgc scanner runs on a 5m interval by default and
trims preallocation (post-eof and cow fork) from inodes that are
otherwise idle. Idle effectively means that iolock can be acquired
without blocking and that the inode has no dirty pagecache or I/O in
flight.
This simple mechanism and heuristic has worked fairly well for
post-eof speculative preallocations. Support for reflink and COW
fork preallocations came sometime later and plugged into the same
mechanism, with similar heuristics. Some recent testing has shown
that COW fork preallocation may be notably more sensitive to blockgc
processing than post-eof preallocation, however.
For example, consider an 8GB reflinked file with a COW extent size
hint of 1MB. A worst case fully randomized overwrite of this file
results in ~8k extents of an average size of ~1MB. If the same
workload is interrupted a couple times for blockgc processing
(assuming the file goes idle), the resulting extent count explodes
to over 100k extents with an average size <100kB. This is
significantly worse than ideal and essentially defeats the COW
extent size hint mechanism.
While this particular test is instrumented, it reflects a fairly
reasonable pattern in practice where random I/Os might spread out
over a large period of time with varying periods of (in)activity.
For example, consider a cloned disk image file for a VM or container
with long uptime and variable and bursty usage. A background blockgc
scan that races and processes the image file when it happens to be
clean and idle can have a significant effect on the future
fragmentation level of the file, even when still in use.
To help combat this, update the heuristic to skip cowblocks inodes
that are currently opened for write access during non-sync blockgc
scans. This allows COW fork preallocations to persist for as long as
possible unless otherwise needed for functional purposes (i.e. a
sync scan), the file is idle and closed, or the inode is being
evicted from cache. While here, update the comments to help
distinguish performance oriented heuristics from the logic that
exists to maintain functional correctness.
Suggested-by: Darrick Wong <djwong@kernel.org>
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
Currently the debug-only xfs_bmap_exact_minlen_extent_alloc allocation
variant fails to drop into the lowmode last resort allocator, and
thus can sometimes fail allocations for which the caller has a
transaction block reservation.
Fix this by using xfs_bmap_btalloc_low_space to do the actual allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
xfs_bmap_exact_minlen_extent_alloc duplicates the args setup in
xfs_bmap_btalloc. Switch to call it from xfs_bmap_btalloc after
doing the basic setup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
Exact minlen allocations only exist as an error injection tool for debug
builds. Currently this is implemented using ifdefs, which means the code
isn't even compiled for non-XFS_DEBUG builds. Enhance the compile test
coverage by always building the code and use the compilers' dead code
elimination to remove it from the generated binary instead.
The only downside is that the alloc_minlen_only field is unconditionally
added to struct xfs_alloc_args now, but by moving it around and packing
it tightly this doesn't actually increase the size of the structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
Userdata and metadata allocations end up in the same allocation helpers.
Remove the separate xfs_bmap_alloc_userdata function to make this more
clear.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
Just like xfs_attr3_leaf_split, xfs_attr_node_try_addname can return
-ENOSPC both for an actual failure to allocate a disk block, but also
to signal the caller to convert the format of the attr fork. Use magic
1 to ask for the conversion here as well.
Note that unlike the similar issue in xfs_attr3_leaf_split, this one was
only found by code review.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
xfs_attr3_leaf_split propagates the need for an extra btree split as
-ENOSPC to it's only caller, but the same return value can also be
returned from xfs_da_grow_inode when it fails to find free space.
Distinguish the two cases by returning 1 for the extra split case instead
of overloading -ENOSPC.
This can be triggered relatively easily with the pending realtime group
support and a file system with a lot of small zones that use metadata
space on the main device. In this case every about 5-10th run of
xfs/538 runs into the following assert:
ASSERT(oldblk->magic == XFS_ATTR_LEAF_MAGIC);
in xfs_attr3_leaf_split caused by an allocation failure. Note that
the allocation failure is caused by another bug that will be fixed
subsequently, but this commit at least sorts out the error handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
xfs_attr3_leaf_add only has two potential return values, indicating if the
entry could be added or not. Replace the errno return with a bool so that
ENOSPC from it can't easily be confused with a real ENOSPC.
Remove the return value from the xfs_attr3_leaf_add_work helper entirely,
as it always return 0.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
xfs_attr_leaf_try_add is only called by xfs_attr_leaf_addname, and
merging the two will simplify a following error handling fix.
To facilitate this move the remote block state save/restore helpers up in
the file so that they don't need forward declarations now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
Use !try_cmpxchg instead of cmpxchg (*ptr, old, new) != old in
xlog_cil_insert_pcp_aggregate(). x86 CMPXCHG instruction returns
success in ZF flag, so this change saves a compare after cmpxchg.
Also, try_cmpxchg implicitly assigns old *ptr value to "old" when
cmpxchg fails. There is no need to re-read the value in the loop.
Note that the value from *ptr should be read using READ_ONCE to
prevent the compiler from merging, refetching or reordering the read.
No functional change intended.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Cc: Chandan Babu R <chandan.babu@oracle.com>
Cc: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Yan Zhen <yanzhen@vivo.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
The definition of xfs_attr_use_log_assist() has been removed since
commit d9c61ccb3b09 ("xfs: move xfs_attr_use_log_assist out of xfs_log.c").
So, Remove the empty declartion in header files.
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
I nominate Carlos Maiolino to take over linux-xfs tree maintainer role for
upstream kernel's XFS code. He has enough experience in Linux kernel and he's
been maintaining xfsprogs and xfsdump trees for a few years now, so he has
sufficient experience with xfs workflow to take over this role.
Signed-off-by: Chandan Babu R <chandanbabu@kernel.org>
Acked-by: Carlos Maiolino <cem@kernel.org>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Carlos Maiolino <cem@kernel.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Move non-boot built-in DTBs to the .rodata section
- Fix Kconfig bugs
- Fix maint scripts in the linux-image Debian package
- Import some list macros to scripts/include/
* tag 'kbuild-fixes-v6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: deb-pkg: Remove blank first line from maint scripts
kbuild: fix a typo dt_binding_schema -> dt_binding_schemas
scripts: import more list macros
kconfig: qconf: fix buffer overflow in debug links
kconfig: qconf: move conf_read() before drawing tree pain
kconfig: clear expr::val_is_valid when allocated
kconfig: fix infinite loop in sym_calc_choice()
kbuild: move non-boot built-in DTBs to .rodata section
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
- Intel PMC fix for suspend/resume issues on some Sky and Kaby Lake
laptops
- Intel Diamond Rapids hw-id additions
- Documentation and MAINTAINERS fixes
- Some other small fixes
* tag 'platform-drivers-x86-v6.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: x86-android-tablets: Fix use after free on platform_device_register() errors
platform/x86: wmi: Update WMI driver API documentation
platform/x86: dell-ddv: Fix typo in documentation
platform/x86: dell-sysman: add support for alienware products
platform/x86/intel: power-domains: Add Diamond Rapids support
platform/x86: ISST: Add Diamond Rapids to support list
platform/x86:intel/pmc: Disable ACPI PM Timer disabling on Sky and Kaby Lake
platform/x86: dell-laptop: Do not fail when encountering unsupported batteries
MAINTAINERS: Update Intel In Field Scan(IFS) entry
platform/x86: ISST: Fix the KASAN report slab-out-of-bounds bug
|
|
Pull kvm fixes from Paolo Bonzini:
"ARM64:
- Fix pKVM error path on init, making sure we do not change critical
system registers as we're about to fail
- Make sure that the host's vector length is at capped by a value
common to all CPUs
- Fix kvm_has_feat*() handling of "negative" features, as the current
code is pretty broken
- Promote Joey to the status of official reviewer, while James steps
down -- hopefully only temporarly
x86:
- Fix compilation with KVM_INTEL=KVM_AMD=n
- Fix disabling KVM_X86_QUIRK_SLOT_ZAP_ALL when shadow MMU is in use
Selftests:
- Fix compilation on non-x86 architectures"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
x86/reboot: emergency callbacks are now registered by common KVM code
KVM: x86: leave kvm.ko out of the build if no vendor module is requested
KVM: x86/mmu: fix KVM_X86_QUIRK_SLOT_ZAP_ALL for shadow MMU
KVM: arm64: Fix kvm_has_feat*() handling of negative features
KVM: selftests: Fix build on architectures other than x86_64
KVM: arm64: Another reviewer reshuffle
KVM: arm64: Constrain the host to the maximum shared SVE VL with pKVM
KVM: arm64: Fix __pkvm_init_vcpu cptr_el2 error path
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fix from Michael Ellerman:
- Allow r30 to be used in vDSO code generation of getrandom
Thanks to Jason A. Donenfeld
* tag 'powerpc-6.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/vdso: allow r30 in vDSO code generation of getrandom
|
|
The blank line causes execve() to fail:
# strace ./postinst
execve("./postinst", ...) = -1 ENOEXEC (Exec format error)
strace: exec: Exec format error
+++ exited with 1 +++
However running the scripts via shell does work (at least with bash)
because the shell attempts to execute the file as a shell script when
execve() fails.
Fixes: b611daae5efc ("kbuild: deb-pkg: split image and debug objects staging out into functions")
Signed-off-by: Aaron Thompson <dev@aaront.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
If we follow "make help" to "make dt_binding_schema", we will see
below error:
$ make dt_binding_schema
make[1]: *** No rule to make target 'dt_binding_schema'. Stop.
make: *** [Makefile:224: __sub-make] Error 2
It should be a typo. So this will fix it.
Fixes: 604a57ba9781 ("dt-bindings: kbuild: Add separate target/dependency for processed-schema.json")
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Reviewed-by: Nicolas Schier <n.schier@avm.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Import list_is_first, list_is_last, list_replace, and list_replace_init.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
platform_device_register() errors
x86_android_tablet_remove() frees the pdevs[] array, so it should not
be used after calling x86_android_tablet_remove().
When platform_device_register() fails, store the pdevs[x] PTR_ERR() value
into the local ret variable before calling x86_android_tablet_remove()
to avoid using pdevs[] after it has been freed.
Fixes: 5eba0141206e ("platform/x86: x86-android-tablets: Add support for instantiating platform-devs")
Fixes: e2200d3f26da ("platform/x86: x86-android-tablets: Add gpio_keys support to x86_android_tablet_init()")
Cc: stable@vger.kernel.org
Reported-by: Aleksandr Burakov <a.burakov@rosalinux.ru>
Closes: https://lore.kernel.org/platform-driver-x86/20240917120458.7300-1-a.burakov@rosalinux.ru/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20241005130545.64136-1-hdegoede@redhat.com
|
|
The WMI driver core now passes the WMI event data to legacy notify
handlers, so WMI devices sharing notification IDs are now being
handled properly.
Fixes: e04e2b760ddb ("platform/x86: wmi: Pass event data directly to legacy notify handlers")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20241005213825.701887-1-W_Armin@gmx.de
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Fix typo in word 'diagnostics' in documentation.
Signed-off-by: Anaswara T Rajan <anaswaratrajan@gmail.com>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20241005070056.16326-1-anaswaratrajan@gmail.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Alienware supports firmware-attributes and has its own OEM string.
Signed-off-by: Crag Wang <crag_wang@dell.com>
Link: https://lore.kernel.org/r/20241004152826.93992-1-crag_wang@dell.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add Diamond Rapids (INTEL_PANTHERCOVE_X) to tpmi_cpu_ids to support
domaid id mappings.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20241003215554.3013807-3-srinivas.pandruvada@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add Diamond Rapids (INTEL_PANTHERCOVE_X) to SST support list by adding
to isst_cpu_ids.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20241003215554.3013807-2-srinivas.pandruvada@linux.intel.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
There have been multiple reports that the ACPI PM Timer disabling is
causing Sky and Kaby Lake systems to hang on all suspend (s2idle, s3,
hibernate) methods.
Remove the acpi_pm_tmr_ctl_offset and acpi_pm_tmr_disable_bit settings from
spt_reg_map to disable the ACPI PM Timer disabling on Sky and Kaby Lake to
fix the hang on suspend.
Fixes: e86c8186d03a ("platform/x86:intel/pmc: Enable the ACPI PM Timer to be turned off when suspended")
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Closes: https://lore.kernel.org/linux-pm/18784f62-91ff-4d88-9621-6c88eb0af2b5@molgen.mpg.de/
Reported-by: Todd Brandt <todd.e.brandt@intel.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219346
Cc: Marek Maslanka <mmaslanka@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Todd Brandt <todd.e.brandt@intel.com>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de> # Dell XPS 13 9360/0596KF
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20241003202614.17181-2-hdegoede@redhat.com
|
|
If the battery hook encounters a unsupported battery, it will
return an error. This in turn will cause the battery driver to
automatically unregister the battery hook.
On machines with multiple batteries however, this will prevent
the battery hook from handling the primary battery, since it will
always get unregistered upon encountering one of the unsupported
batteries.
Fix this by simply ignoring unsupported batteries.
Reviewed-by: Pali Rohár <pali@kernel.org>
Fixes: ab58016c68cc ("platform/x86:dell-laptop: Add knobs to change battery charge settings")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20241001212835.341788-4-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
