| Age | Commit message (Collapse) | Author |
|---|
|
When a device signals remote wakeup on a roothub, and the suspend change
bit is set, the host controller driver must not give control back to the
USB core until the port goes back into the active state.
EHCI accomplishes this by waiting in the get port status function until
the PORT_RESUME bit is cleared:
/* stop resume signaling */
temp &= ~(PORT_RWC_BITS | PORT_SUSPEND | PORT_RESUME);
ehci_writel(ehci, temp, status_reg);
clear_bit(wIndex, &ehci->resuming_ports);
retval = ehci_handshake(ehci, status_reg,
PORT_RESUME, 0, 2000 /* 2msec */);
Similarly, the xHCI host should wait until the port goes into U0, before
passing control up to the USB core. When the port transitions from the
RExit state to U0, the xHCI driver will get a port status change event.
We need to wait for that event before passing control up to the USB
core.
After the port transitions to the active state, the USB core should time
a recovery interval before it talks to the device. The length of that
recovery interval is TRSMRCY, 10 ms, mentioned in the USB 2.0 spec,
section 7.1.7.7. The previous xHCI code (which did not wait for the
port to go into U0) would cause the USB core to violate that recovery
interval.
This bug caused numerous USB device disconnects on remote wakeup under
ChromeOS and a Lynx Point LP xHCI host that takes up to 20 ms to move
from RExit to U0. ChromeOS is very aggressive about power savings, and
sets the autosuspend_delay to 100 ms, and disables USB persist.
I attempted to replicate this bug with Ubuntu 12.04, but could not. I
used Ubuntu 12.04 on the same platform, with the same BIOS that the bug
was triggered on ChromeOS with. I also changed the USB sysfs settings
as described above, but still could not reproduce the bug under Ubuntu.
It may be that ChromeOS userspace triggers this bug through additional
settings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
If a command on the command ring needs to be cancelled before it is handled
it can be turned to a no-op operation when the ring is stopped.
We want to store the command ring enqueue pointer in the command structure
when the command in enqueued for the cancellation case.
Some commands used to store the command ring dequeue pointers instead of enqueue
(these often worked because enqueue happends to equal dequeue quite often)
Other commands correctly used the enqueue pointer but did not check if it pointed
to a valid trb or a link trb, this caused for example stop endpoint command to timeout in
xhci_stop_device() in about 2% of suspend/resume cases.
This should also solve some weird behavior happening in command cancellation cases.
This patch is based on a patch submitted by Sarah Sharp to linux-usb, but
then forgotten:
http://marc.info/?l=linux-usb&m=136269803207465&w=2
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c047ff7cf587b318fe377061a353c120f "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
|
|
When a command times out, the command ring is first aborted,
and then stopped. If the command ring is empty when it is stopped
the stop event will point to next command which is not yet set.
xHCI tries to handle this next event often causing an oops.
Don't handle command completion events on stopped cmd ring if ring is
empty.
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c047ff7cf587b318fe377061a353c120f "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reported-by: Giovanni <giovanni.nervi@yahoo.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
|
|
|
|
MRP doesn't implement the periodictimer in 802.1Q, so it never retries
if packets get lost. I ran into this problem when MRP sent a MVRP
JoinIn before the interface was fully up. The JoinIn was lost, MRP
didn't retry, and MVRP registration failed.
Tested against Juniper QFabric switches
Signed-off-by: Noel Burton-Krahn <noel@burton-krahn.com>
Acked-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Actually re-send packets when the T1 timer runs out. This fixes a bug
where packets are waiting on the write queue until disconnection when
no other traffic is outstanding.
Signed-off-by: Josselin Costanzi <josselin.costanzi@mobile-devices.fr>
Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add generic rule on encountering Belkin bluetooth usb device F8065bf.
Relevant section from /sys/kernel/debug/usb/devices:
T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=050d ProdID=065a Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=0002723E2D29
C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
Signed-off-by: Ken O'Brien <kernel@kenobrien.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Yuval Mintz says:
====================
This patch contains various bug fixes, half of which are SR-IOV related
(some fixing issues in the recently added VF RSS support), while the other fix
a wide assortments of issues in the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b9871bcf "bnx2x: VF RSS support - PF side" has deprecated one of
the previous existing messages. If an old VF driver were to send this message
to the PF then the PF will not reply and leave the mailbox in an unsteady
state (and cause a timeout on the VF side).
Wait until firmware ack is written before unlocking channel
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During flows which mask block attentions (e.g., register dump) all parities
are masked. However, unlike other blocks the MCP's attention is not masked
inside the block but rather the indication to the driver. If another attention
(e.g., link change) will occour while there's an MCP parity, the driver will
ignore the fact that the parity is masked and erroneously report a parity.
This patch forces the driver to read the MCP masking while checking for
parities.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During error flows while loading cnic the return value was incorrectly replaced
by that of bnx2x_set_real_num_queues(); If that function was to finish
successfully then the cnic would have mistakenly thought the load ended
successfully, causing issues (& panics) later on.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnx2x_iov_static_resc() should be called after IGU was read for information on
the number of available VFs, so that resources will be correctly set.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to incorrect usage of PF macros when reading information relating to
interrupts, some PFs were erroneously unable to support VFs.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When system CPU is stressed it's possible that the driver will not be able
to pulse the FW every second, which will cause the log to be filled with
error messages.
Increasing the threshold to 5 seconds seems to be enough to eliminate the
issue.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are a number of small staging tree and iio driver fixes. Nothing
major, just lots of little things"
* tag 'staging-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (34 commits)
iio:buffer_cb: Add missing iio_buffer_init()
iio: Prevent race between IIO chardev opening and IIO device free
iio: fix: Keep a reference to the IIO device for open file descriptors
iio: Stop sampling when the device is removed
iio: Fix crash when scan_bytes is computed with active_scan_mask == NULL
iio: Fix mcp4725 dev-to-indio_dev conversion in suspend/resume
iio: Fix bma180 dev-to-indio_dev conversion in suspend/resume
iio: Fix tmp006 dev-to-indio_dev conversion in suspend/resume
iio: iio_device_add_event_sysfs() bugfix
staging: iio: ade7854-spi: Fix return value
staging:iio:hmc5843: Fix measurement conversion
iio: isl29018: Fix uninitialized value
staging:iio:dummy fix kfifo_buf kconfig dependency issue if kfifo modular and buffer enabled for built in dummy driver.
iio: at91: fix adc_clk overflow
staging: line6: add bounds check in snd_toneport_source_put()
Staging: comedi: Fix dependencies for drivers misclassified as PCI
staging: r8188eu: Adjust RX gain
staging: r8188eu: Fix smatch warning in core/rtw_ieee80211.
staging: r8188eu: Fix smatch error in core/rtw_mlme_ext.c
staging: r8188eu: Fix Smatch off-by-one warning in hal/rtl8188e_hal_init.c
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB fixes for 3.12-rc2.
One is a revert of a EHCI change that isn't quite ready for 3.12.
Others are minor things, gadget fixes, Kconfig fixes, and some quirks
and documentation updates.
All have been in linux-next for a bit"
* tag 'usb-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: pl2303: distinguish between original and cloned HX chips
USB: Faraday fotg210: fix email addresses
USB: fix typo in usb serial simple driver Kconfig
Revert "USB: EHCI: support running URB giveback in tasklet context"
usb: s3c-hsotg: do not disconnect gadget when receiving ErlySusp intr
usb: s3c-hsotg: fix unregistration function
usb: gadget: f_mass_storage: reset endpoint driver data when disabled
usb: host: fsl-mph-dr-of: Staticize local symbols
usb: gadget: f_eem: Staticize eem_alloc
usb: gadget: f_ecm: Staticize ecm_alloc
usb: phy: omap-usb3: Fix return value
usb: dwc3: gadget: avoid memory leak when failing to allocate all eps
usb: dwc3: remove extcon dependency
usb: gadget: add '__ref' for rndis_config_register() and cdc_config_register()
usb: dwc3: pci: add support for BayTrail
usb: gadget: cdc2: fix conversion to new interface of f_ecm
usb: gadget: fix a bug and a WARN_ON in dummy-hcd
usb: gadget: mv_u3d_core: fix violation of locking discipline in mv_u3d_ep_disable()
|
|
Move probe out of __init section and don't use platform_driver_probe
which cannot be used with deferred probing.
Since commit e9354576 ("gpiolib: Defer failed gpio requests by default")
and 04bf3011 ("regulator: Support driver probe deferral") this driver
might return -EPROBE_DEFER if a gpio_request or regulator_get fails.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Move probe out of __init section and don't use platform_driver_probe
which cannot be used with deferred probing.
Since commit e9354576 ("gpiolib: Defer failed gpio requests by default")
this driver might return -EPROBE_DEFER if a gpio_request fails.
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Starting with UVD3 message and feedback buffers have their
own 256MB segment, so no need to force them into VRAM any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The tests are only usable if the acceleration engines have
been successfully initialized.
Based on an initial patch from: Alex Ivanov <gnidorah@p0n4ik.tk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Allow user to change the number of IOs that are reserved by
bio-based DM's mempools by writing to this file:
/sys/module/dm_mod/parameters/reserved_bio_based_ios
The default value is RESERVED_BIO_BASED_IOS (16). The maximum allowed
value is RESERVED_MAX_IOS (1024).
Export dm_get_reserved_bio_based_ios() for use by DM targets and core
code. Switch to sizing dm-io's mempool and bioset using DM core's
configurable 'reserved_bio_based_ios'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
|
|
Allow user to change the number of IOs that are reserved by
request-based DM's mempools by writing to this file:
/sys/module/dm_mod/parameters/reserved_rq_based_ios
The default value is RESERVED_REQUEST_BASED_IOS (256). The maximum
allowed value is RESERVED_MAX_IOS (1024).
Export dm_get_reserved_rq_based_ios() for use by DM targets and core
code. Switch to sizing dm-mpath's mempool using DM core's configurable
'reserved_rq_based_ios'.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
|
|
Bio-based device mapper processing doesn't need larger mempools (like
request-based DM does), so lower the number of reserved entries for
bio-based operation. 16 was already used for bio-based DM's bioset
but mistakenly wasn't used for it's _io_cache.
Formalize difference between bio-based and request-based defaults by
introducing RESERVED_BIO_BASED_IOS and RESERVED_REQUEST_BASED_IOS.
(based on older code from Mikulas Patocka)
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
|
|
Fix issue where the block layer would stack the discard limits of the
pool's data device even if the "ignore_discard" pool feature was
specified.
The pool and thin device(s) still had discards disabled because the
QUEUE_FLAG_DISCARD request_queue flag wasn't set. But to avoid user
confusion when "ignore_discard" is used: both the pool device and the
thin device(s) have zeroes for all discard limits.
Also, always set discard_zeroes_data_unsupported in targets because they
should never advertise the 'discard_zeroes_data' capability (even if the
pool's data device supports it).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
|
|
This is a partial revert of c6cf7777a32da874fabec4fd1c2a579f0ba4e4dd.
We need to take into account the clk voltage dependencies of the
board. Not doing so can lead to stability issues on certain
boards if the clks exceed the levels in the dep tables.
DPM already takes that into account, so for optimal performance,
use DPM.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch adds a helper function to fetch the max clock
from the voltage clock dependecy tables. Clocks above that
level tend to be unstable and will require additional driver
tweaks in order to work properly.
This patch implemented the helper function to fetch the max clocks
from the dependency tables. The following patches implement the
per-asic clock filtering.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
I missed this when I fixed up this file.
Noticed-by: Mathias Fröhlich <Mathias.Froehlich@gmx.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fix the linear range settings in commit 5ff26a14c3331
"regulator: wm831x-ldo: Convert to use linear ranges".
For wm831x_gp_ldo:
We have below equations for list voltage before converting to linear ranges:
sel <= 0xe:
volt = 0.9-1.6V in 50mV steps
sel <= 0x1f:
volt = 1.7-3.3V in 100mV steps
max_uV for the first linear range should be 1600000 rather than 1650000. Fix it.
For wm831x_aldo:
We have below equations for list voltage before converting to linear ranges:
sel <= 0xc:
volt = 1-1.6V in 50mV steps
sel <= 0x1f
volt = 1.7-3.5V in 100mV steps
max_uV for the first linear range should be 1600000 rather than 1650000. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The some platforms (e.g., ARM) initializes their clocks as
late_initcalls for some unknown reason. So make sure
random_int_secret_init() is run after all of the late_initcalls are
run.
Cc: stable@vger.kernel.org
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
|
sizeof() is already size_t so there is no need to cast here. Generally,
casting inside the min() macro instead of using min_t() is considered
bad style.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Have pinconf_dbg_config_write() return a ssize_t. This fixes the following
compilation warning:
drivers/pinctrl/pinconf.c:617:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/pinctrl/pinconf.c:617:2: warning: (near initialization for ‘pinconf_dbg_pinconfig_fops.write’) [enabled by default]
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Dell PowerEdge C6100 machines fail to completely reboot about 20% of the time.
Signed-off-by: Masoud Sharbiani <msharbiani@twitter.com>
Signed-off-by: Vinson Lee <vlee@twitter.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/1379717947-18042-1-git-send-email-vlee@freedesktop.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Cc: a.p.zijlstra@chello.nl
Cc: eranian@google.com
Cc: ak@linux.intel.com
Link: http://lkml.kernel.org/r/1379837953-17755-1-git-send-email-zheng.z.yan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
On 848xx PHY (10G-baseT), half-duplex was always advertised regardless of the
actual configuration. Change the 848xx duplex settings to advertise half-duplex
only if configured.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix Warpcore mode setting when active DAC (Direct Attached Cable) is detected.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
when 1G-optic module was plugged in, internal loopback test failed because the
driver used to check the optic module (with no need), and for 1G optic module,
the link speed was forced down to 1G, while the XMAC (10G MAC) was enabled.
This patch avoid accessing optic module in case internal loopback was selected,
and update the link speed in case 1G optic module was detected during init
stage.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Relocate bnx2x_disable_kr2 function, and use it to disable KR2 in case it is not
configured in order to clear it's configuration, otherwise the link may come up
at 20G instead of the requested 10G-KR. In addition, restart AN after
disabling KR2 as part of the KR2 work-around.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, in case of KR link down, the driver would reset the PHY and restart
auto negotiation only when old Warpcore microcode was used (below D108).
This patch comes to generalize this by keep trying to restart KR link,
regardless of Warpcore microcode, since it was found that it solves another link
issue which source is a link-partner. As part of this change, the signal
detect is no longer a condition to apply the work-around to cover this new case.
Like before, as long as the link is down, AN will be restarted every 2 seconds.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm fixes from Dave Airlie:
- some small fixes for msm and exynos
- a regression revert affecting nouveau users with old userspace
- intel pageflip deadlock and gpu hang fixes, hsw modesetting hangs
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (22 commits)
Revert "drm: mark context support as a legacy subsystem"
drm/i915: Don't enable the cursor on a disable pipe
drm/i915: do not update cursor in crtc mode set
drm/exynos: fix return value check in lowlevel_buffer_allocate()
drm/exynos: Fix address space warnings in exynos_drm_fbdev.c
drm/exynos: Fix address space warning in exynos_drm_buf.c
drm/exynos: Remove redundant OF dependency
drm/msm: drop unnecessary set_need_resched()
drm/i915: kill set_need_resched
drm/msm: fix potential NULL pointer dereference
drm/i915/dvo: set crtc timings again for panel fixed modes
drm/i915/sdvo: Robustify the dtd<->drm_mode conversions
drm/msm: workaround for missing irq
drm/msm: return -EBUSY if bo still active
drm/msm: fix return value check in ERR_PTR()
drm/msm: fix cmdstream size check
drm/msm: hangcheck harder
drm/msm: handle read vs write fences
drm/i915/sdvo: Fully translate sync flags in the dtd->mode conversion
drm/i915: Use proper print format for debug prints
...
|
|
Pull block IO fixes from Jens Axboe:
"After merge window, no new stuff this time only a collection of neatly
confined and simple fixes"
* 'for-3.12/core' of git://git.kernel.dk/linux-block:
cfq: explicitly use 64bit divide operation for 64bit arguments
block: Add nr_bios to block_rq_remap tracepoint
If the queue is dying then we only call the rq->end_io callout. This leaves bios setup on the request, because the caller assumes when the blk_execute_rq_nowait/blk_execute_rq call has completed that the rq->bios have been cleaned up.
bio-integrity: Fix use of bs->bio_integrity_pool after free
blkcg: relocate root_blkg setting and clearing
block: Convert kmalloc_node(...GFP_ZERO...) to kzalloc_node(...)
block: trace all devices plug operation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"These are mostly bug fixes and a two small performance fixes. The
most important of the bunch are Josef's fix for a snapshotting
regression and Mark's update to fix compile problems on arm"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (25 commits)
Btrfs: create the uuid tree on remount rw
btrfs: change extent-same to copy entire argument struct
Btrfs: dir_inode_operations should use btrfs_update_time also
btrfs: Add btrfs: prefix to kernel log output
btrfs: refuse to remount read-write after abort
Btrfs: btrfs_ioctl_default_subvol: Revert back to toplevel subvolume when arg is 0
Btrfs: don't leak transaction in btrfs_sync_file()
Btrfs: add the missing mutex unlock in write_all_supers()
Btrfs: iput inode on allocation failure
Btrfs: remove space_info->reservation_progress
Btrfs: kill delay_iput arg to the wait_ordered functions
Btrfs: fix worst case calculator for space usage
Revert "Btrfs: rework the overcommit logic to be based on the total size"
Btrfs: improve replacing nocow extents
Btrfs: drop dir i_size when adding new names on replay
Btrfs: replay dir_index items before other items
Btrfs: check roots last log commit when checking if an inode has been logged
Btrfs: actually log directory we are fsync()'ing
Btrfs: actually limit the size of delalloc range
Btrfs: allocate the free space by the existed max extent size when ENOSPC
...
|
|
'samples' is 64bit operant, but do_div() second parameter is 32.
do_div silently truncates high 32 bits and calculated result
is invalid.
In case if low 32bit of 'samples' are zeros then do_div() produces
kernel crash.
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This property is no longer required by the GPIO binding. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Commit a1bc260bb5f5d95da854be7898202d788e94448d ("gpio: clean up
gpio-ranges documentation") deprecated the #gpio-range-cells property.
Replace its usage with a hardcoded value in the gpio-rcar driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
e5c9b4cd665106d9b5397114ea81a53059410b6a ("sh_eth: get R8A7740 support
out of #ifdef") exchanged sh-eth driver name to r8a7740-gether, but,
eva_pinctrl_map[] didn't follow it. Fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Patch 638591c enabled building the AES assembler code in Thumb2 mode.
However, this code used arithmetic involving PC rather than adr{l}
instructions to generate PC-relative references to the lookup tables,
and this needs to take into account the different PC offset when
running in Thumb mode.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
