| Age | Commit message (Collapse) | Author |
|---|
|
Enable STM32 IPCC mailbox driver for STM32MP157c-ed1 board.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Add configuration on DT for IPCC mailbox driver.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds sdmmc1 support on stm32mp157a dk1 board.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds sdmmc1 support on stm32mp157c ed1 board.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds support of sdmmc1 on stm32mp157c.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds sdmmc1 support on stm32h743i disco board.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds sdmmc1 support on stm32h743i eval board.
This board has an external driver to control signal direction polarity.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
This patch adds support of sdmmc1 on stm32h743.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Remove the "console=ttySAC..." argument from DTSes having a proper
stdout-path property. To make the code functionally equivalent, add the
serial port baud rate and parity.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Replacing bootargs with stdout-path property in chosen node allows using
early console by adding just 'earlycon' parameter to the kernel command
line.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
The MBUS (and its associated controller) is the bus in the Allwinner SoCs
that DMA devices use in the system to access the memory.
Among other things (and depending on the SoC generation), it can also
enforce priorities or report bandwidth usages on a per-master basis.
One of the most notable thing is that instead of having the same mapping
for the RAM than the CPU, it maps it at address 0, which means we'll have
to do address translation thanks to the dma-ranges property.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
This patch adds CMT{0|1|2|3} device nodes for r8a77990 SoC.
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds CMT{0|1|2|3} device nodes for r8a77965 SoC.
Tested-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This patch adds CMT{0|1|2|3} device nodes for r8a7795 SoC.
Tested-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
We can now add l4 abe interconnect hierarchy and ti-sysc data with
ti-sysc driver supporting external optional clocks needed by mcpdm.
This data is generated based on platform data from a booted system
and the interconnect acces protection registers for ranges. To avoid
regressions, we initially validate the device tree provided data
against the existing platform data on boot.
Note that mcpdm we now need to enable at module level only for devices
that have the external pdmclk wired from the PMIC as the clock is
needed for the module to be accessible.
Also note that abe seems to be the same as on omap4 except for domains
and clocks and we may be able to combine the l4 abe data later on.
But let's play it safe and just initially use what we have already
defined in the platform data.
Cc: devicetree@vger.kernel.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now add l4 abe interconnect hierarchy and ti-sysc data with
ti-sysc driver supporting external optional clocks needed by mcpdm.
This data is generated based on platform data from a booted system
and the interconnect acces protection registers for ranges. To avoid
regressions, we initially validate the device tree provided data
against the existing platform data on boot.
Note that mcpdm we now need to enable at module level only for devices
that have the external pdmclk wired from the PMIC as the clock is
needed for the module to be accessible.
Cc: devicetree@vger.kernel.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The mcpdm module found on omap4 and 5 needs pdmclk clock from
the pmic that may or may not be wired. Without this clock we
cannot read the registers for mcpdm at all. For the external
mcpdm clock to work, it needs to be muxed at the module level
for ti-sysc driver probe to mux it early enough for probe.
Let's set up a common file for it to make things a bit easier
to make l4 abe interconnect to probe with ti-sysc driver. Note
that this is not needed for omap5 as we can just update mcpdm
muxing in omap5-board-common.dtsi in later patches.
Cc: devicetree@vger.kernel.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For non legacy cases, add generic sysc_enable_module()
and sysc_disable_module() functions.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", the driver now accepts this name, use it here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Mark matrix-keypad as a wakeup source.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
When going to suspend to ram mode (or rtc-only mode), the DDR regulator
must be told to stay on, else this rail will go down when the PMIC_EN
signal is deasserted.
Signed-off-by: Mike Erdahl <m-erdahl@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
These regulator outputs are needed even in deep sleep modes to prevent
low-voltage detection events. Make these always ON to avoid this.
Signed-off-by: Kabir Sahane <x0153567@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ti,syscon-lane-sel and ti,syscon-lane-conf properties specific to enable
PCIe x2 lane mode are added here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Orange Pi 3 is a H6 based SBC made by Xulong, released in January 2019. It
has the following features:
- Allwinner H6 quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB or 2GB LPDDR3 RAM
- AXP805 PMIC
- AP6256 Wifi/BT 5.0
- USB 2.0 host port (A)
- USB 2.0 micro usb, OTG
- USB 3.0 Host + 4 port USB hub (GL3510)
- Gigabit Ethernet (Realtek RTL8211E phy)
- HDMI 2.0 port
- soldered eMMC (optional)
- 3x LED (one is on the bottom)
- microphone
- audio jack
- PCIe
Add basic support for the board.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Add new Xunlong Orange Pi 3 board compatible string to the bindings
documentation.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
I2C2 is available on the PE pingroup, on the same pins as the camera
sensor interface (CSI) controller's camera control interface pins.
This provides an option to use I2C2 instead of that control interface
to configure camera sensors.
Add a pinctrl node for it. The property /omit-if-no-ref/ is added to
keep the device tree blob size down if it is unused.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Beelink GS1 device-tree has been introduced.
Add it to the sunxi yaml documentation.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- FN-Link 6222B-SRB Wifi/BT
- 1x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- S/PDIF Tx
- IR receiver
- 5V/2A DC power supply
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Shenzhen AZW Technology Co. Ltd. is a manufacturer specialized in Android
smart TV boxes, Intel mini PCs and home cloud TV boxes with NAS.
Add the vendor prefix for AZW.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
There is only one pinmuxing available for each MMC controller.
Move the pinctrl to the SOC
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
TBS A711 tablet has volume up/down keys connected to r_lradc. Add
support for these keys.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Allwinner A83T SoC has a low res adc like the one in Allwinner A10 SoC.
Now the driver has been modified to support it.
Add support for it.
Signed-off-by: Ziping Chen <techping.chan@gmail.com>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
We can now drop legacy platform data one interconnect target module at
a time in favor of the device tree based data that has been added earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now drop legacy platform data one interconnect target module at
a time in favor of the device tree based data that has been added earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now drop legacy platform data one interconnect target module at
a time in favor of the device tree based data that has been added earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now drop legacy platform data one interconnect target module at
a time in favor of the device tree based data that has been added earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now drop legacy platform data one interconnect target module at
a time in favor of the device tree based data that has been added earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now drop legacy platform data one interconnect target module at
a time in favor of the device tree based data that has been added earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now drop legacy platform data one interconnect target module at
a time in favor of the device tree based data that has been added earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now drop legacy platform data one interconnect target module at
a time in favor of the device tree based data that has been added earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now drop legacy platform data one interconnect target module at
a time in favor of the device tree based data that has been added earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now drop legacy platform data one interconnect target module at
a time in favor of the device tree based data that has been added earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now drop legacy platform data one interconnect target module at
a time in favor of the device tree based data that has been added earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now drop legacy platform data one interconnect target module at
a time in favor of the device tree based data that has been added earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now drop legacy platform data one interconnect target module at
a time in favor of the device tree based data that has been added earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now drop legacy platform data one interconnect target module at
a time in favor of the device tree based data that has been added earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now drop legacy platform data one interconnect target module at
a time in favor of the device tree based data that has been added earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now drop legacy platform data one interconnect target module at
a time in favor of the device tree based data that has been added earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We can now drop legacy platform data one interconnect target module at
a time in favor of the device tree based data that has been added earlier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The defines are taken from dt-bindings/pinctrl/am33xx.h
Signed-off-by: Christina Quast <cquast@hanoverdisplays.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
