| Age | Commit message (Collapse) | Author |
|---|
|
Subsystem specific bindings for the Arizona devices are being factored
out of the MFD binding document into separate documents for each
subsystem. This patch adds a binding document that covers the existing
extcon specific bindings.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add device tree binding documentation for the Arizona drivers
to the MAINTAINERS file.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Binding documentation has been added in new subsystem specific binding
documents. This patch removes the now duplicate documentation from the
MFD documentation.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds rt5033-led sub device to support it.
Signed-off-by: Ingi Kim <ingi2.kim@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Intel Broxton has the same LPSS block than Intel Sunrisepoint so add
Broxton PCI IDs to the list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Intel Broxton has the same LPSS block than Intel Sunrisepoint so add
Broxton ACPI IDs to the list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The "jd_active" variable needs to be signed for the error handling to
work.
Fixes: 143e5887ae57 ('mfd: arizona: factor out checking of jack detection state')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Just like other NAND controllers, the NAND READID command only works
in 8bit mode for all versions of BRCMNAND controller.
This patch forces 8bit mode for each NAND CS in brcmnand_init_cs()
before doing nand_scan_ident() to ensure that BRCMNAND controller
is in 8bit mode when NAND READID command is issued.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Use enum instead of magic numbers for CFG and CFG_EXT bitfields.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Anup Patel <anup.patel@broadcom.com>
|
|
Default the brightness to 2048 and add possibility to override this in
device tree.
Suggested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
control ports
Digi 002/003 family uses two ways to transfer MIDI messages. They're
different mechanisms, while it's better to handle the ways in different
ALSA rawmidi character devices because one character device has just a
set of operations.
This commit adds another rawmidi character device for control MIDI port. As
a result, first rawmidi character device is just for MIDI messages
transferred by isochronous packets.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Digi 002/003 family has two types of MIDI port; one is for physical MIDI
port and another is for MIDI control message. The former is transferred in
isochronous packet, and the latter is transferred by asynchronous
transaction. These transmission mechanisms are completely different, while
current ALSA digi00x driver defines a set of operations for them with
several condition statements. As a result, codes for the operation are
messy.
This commit adds a set of MIDI operation for control MIDI ports. In later
commit, it's applied as an operation for ALSA rawmidi character device.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In following commit, new functions and variables are added for operations
of MIDI control port.
This commit is a preparation. Current identifiers are renamed so that they
mean physical MIDI ports.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
rbd requires stable pages, as it performs a crc of the page data before
they are send to the OSDs.
But since kernel 3.9 (patch 1d1d1a767206fbe5d4c69493b7e6d2a8d08cc0a0
"mm: only enforce stable page writes if the backing device requires
it") it is not assumed anymore that block devices require stable pages.
This patch sets the necessary flag to get stable pages back for rbd.
In a ceph installation that provides multiple ext4 formatted rbd
devices "bad crc" messages appeared regularly (ca 1 message every 1-2
minutes on every OSD that provided the data for the rbd) in the
OSD-logs before this patch. After this patch this messages are pretty
much gone (only ca 1-2 / month / OSD).
Cc: stable@vger.kernel.org # 3.9+, needs backporting
Signed-off-by: Ronny Hegewald <Ronny.Hegewald@online.de>
[idryomov@gmail.com: require stable pages only in crc case, changelog]
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
This commit does not change the function behavior.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Addresses should not be prefixed contain '0x' in nodes.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
This patch marks all the reference to the legacy wakeup bindings
and replaces them with the standard "wakeup-source" property.
All these legacy property are also listed under a separate section in
the generic wakeup-source binding document.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Currently different drivers use multiple forms of annotating devices
that should be set up as wakeup sources for the system.
This patch adds a separate binding document inorder to standardize and
consolidate to use "wakeup-source" boolean property to mark the devices
as wakeup capable.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
syncpoints are resources provided by host1x and their lifetime is tied
to the host1x device. They are not properly reference counted either, so
removing the host1x device before any of its clients causes a use-after-
free error. Adding proper reference counting would be a major enterprise
so work around it for now by requesting and freeing the syncpoint at
init and exit time, respectively. The host1x device is guaranteed to be
around at this point.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The platform_no_drv_owner.cocci coccinelle script generates the
following warning:
drivers/gpu/drm/bridge/nxp-ptn3460.c:403:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically. Patch
generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The platform_no_drv_owner.cocci coccinelle script generates the
following warning:
drivers/gpu/drm/bridge/parade-ps8622.c:671:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically. Patch
generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This patch adds the mfd cell info for axp288 power key device.
Signed-off-by: Borun Fu <borun.fu@linux.intel.com>
Signed-off-by: Fei Yang <fei.yang@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Document a new Device Tree property 'samsung,s2mps11-wrstbi-ground'
indicating that WRSTBI pin of S2MPS13 PMIC is pulled down so
corresponding buck warm reset function should be disabled.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The WRSTBI bit (disabled by default but enabled by bootloader), when
set, is responsible for resetting voltages to default values of
certain bucks on falling edge of Warm Reset Input pin from AP.
However on some boards (with S2MPS13) the pin is pulled down so any
suspend will effectively trigger the reset of bucks supplying the power
to the little and big cores. In the same time when resuming, these bucks
must provide voltage greater or equal to voltage before suspend to match
the frequency chosen by cpufreq. If voltage (default value of voltage
after reset) is lower than one set by cpufreq before suspend, then
system will hang during resuming.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
There are different revisions of the same chipset. For example S2MPS13 has
more than 2 revisions. They differ slightly in regulator constraints.
Print the revision number to easily find which PMIC is used on the board.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
In the case of a device tree config the code uses the device ID
from the DT entry to check which codec is required but when storing
the ID into struct arizona it was always using the non-DT SPI device
table to get an ID.
This patch changes the code to store the correct ID into struct arizona.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Remove the use of #ifdefs around each case statement of the chip ID
and type validation switches.
We must ensure that the contained code still compiles to nothing if
support for that codec was not built into the kernel, to prevent
creation of link references to missing functions. So the ifdefs are
replaced with a use of the IS_ENABLED() macro.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The code was using a switch on the code type to execute
one of several mfd_add_devices() calls. We're already
switching on the code type earlier in the function to
select the correct patch function so we can roll selection
of the mfd device table into the same switch.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
If the declared codec type doesn't match the detected type
we issue a log message but carry on registering the device,
so a dev_warn() is appropriate rather than a dev_err()
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Currently runtime_suspend will fully power off the codec if
the jack detection is not enabled. Not all future codecs will
have jack detection so to prepare for these codecs this patch
factors out the check so that it be called as needed in the
existing codec-specific switch cases.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Currently DCVDD isolation is enabled and disabled for
runtime_suspend and runtime_resume. Future codecs will not
have the isolation control so to prepare for these codecs
this patch factors out the isolation control allowing it to
be called as needed in the existing codec-specific switch cases.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is required since
commit 7e5071199355 ("mfd: tps6105x: Use i2c regmap to access registers").
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
We were getting build warning about unused variable 'ret'.
The commit c749db571dcf has removed the use of ret but missed removing
the variable which is unused now.
Fixes: c749db571dcf ("mfd: lm3533: Simplify function return logic")
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
rts522a(rts5227s) is derived from rts5227, and mainly same with rts5227.
Add it to file mfd/rts5227.c to support this chip.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Rename get_device_type() to da9062_get_device_type().
This function is only used in this file so make it static.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The driver depends on ARCH_NOMADIK but there isn't a build dependency
so it's a good idea to allow the driver to always be built when the
COMPILE_TEST option is enabled.
That way, the driver can be built with a config generated by make
allyesconfig and check if a patch would break the build.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Definitions for GPIO registers 8, 9, 10, 11, 12 and 13 are added into
the register header file.
- DA9052_GPIO_8_9_REG 25
- DA9052_GPIO_10_11_REG 26
- DA9052_GPIO_12_13_REG 27
A modification is also made to the MFD core code to define these registers
as readable and writable. The functions for da9052_reg_readable() and
da9052_reg_writeable() have had their case statements altered to include
these new registers.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This driver supports the new Atmel Flexcom. The Flexcom is a wrapper which
integrates one SPI controller, one I2C controller and one USART. Only one
function can be enabled at a time. This driver selects the function once
for all, when the Flexcom is probed, according to the value of the new
"atmel,flexcom-mode" device tree property.
This driver has chosen to present the Flexcom to the system as a MFD so
the implementation is seamless for the existing Atmel SPI, I2C and USART
drivers.
Also the Flexcom embeds FIFOs: the latest patches of the SPI, I2C and
USART drivers take advantage of this new feature.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch documents the DT bindings for the Atmel Flexcom which will be
introduced by sama5d2x SoCs. These bindings will be used by the actual
Flexcom driver to be sent in another patch.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch defines some macros to be used as value for the
"atmel,flexcom-mode" DT property. This value is then written into
the Operating Mode (OPMODE) bit field of the Flexcom Mode Register.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The call to kstrtoul() will corrupt memory on 64 bit systems because an
int is 4 bytes and a long is 8.
Also it's not a good idea to let users trigger a dev_err() because it
just ends up flooding /var/log/messages so I removed the printk.
Fixes: 2ddd2086ea9c ('mfd: add Intel Broxton Whiskey Cove PMIC driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The invoked functions already return zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The invoked functions already return zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The invoked function already returns zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The invoked functions already return zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The invoked functions already return zero on success or a negative
errno code so there is no need to open code the logic in the caller.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The ret variable is not needed since is not used in the
function. Remove the variable and just return 0 instead.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The ret variable is not needed since is not used in the
function. Remove the variable and just return 0 instead.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The ret variable is not needed since is not used in the
function. Remove the variable and just return 0 instead.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
tps6105 driver provides two cells. One is for GPIO and another one is
for selected mode depending on platform data. When tps6105x is used in
GPIO-only mode, this driver calls mfd_add_devices() with mfd_cell
.name == NULL. This value causes an oops in platform_device_register()
later.
The following patch adds a mfd_cell for each possible mode thereby
excluding .name assignment in runtime.
Signed-off-by: Denis Grigoryev <grigoryev@fastwel.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
