| Age | Commit message (Collapse) | Author |
|---|
|
There is an issue around with error handling and graph management with
the exising code, none of the error paths close the graph, which result in
leaving the loaded graph in dsp, however the driver thinks otherwise.
This can have a nasty side effect specially when we try to load the same
graph to dsp, dsp returns error which leaves the board with no sound and
requires restart.
Fix this by properly closing the graph when we hit errors between
open and close.
Fixes: 30ad723b93ad ("ASoC: qdsp6: audioreach: add q6apm lpass dai support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # X13s
Link: https://lore.kernel.org/r/20240613-q6apm-fixes-v1-1-d88953675ab3@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the ASP1 DAI is hooked up by the machine driver the ASP TX mixer
sources should be initialized to disconnected. There aren't currently
any available products using the ASP so this doesn't affect any
existing systems.
The cs35l56 does not have any fixed default for the mixer source
registers. When the cs35l56 boots, its firmware patches these registers
to setup a system-specific routing; this is so that Windows can use
generic SDCA drivers instead of needing knowledge of chip-specific
registers. The setup varies between end-products, which each have
customized firmware, and so the default register state varies between
end-products. It can also change if the firmware on an end-product is
upgraded - for example if a change was needed to the routing for Windows
use-cases. It must be emphasized that the settings applied by the
firmware are not internal magic tuning; they are statically implementing
use-case setup that on Linux would be done via ALSA controls.
The driver is currently syncing the mixer controls with whatever
initial state the firmware wrote to the registers, so that they report
the actual audio routing. But if the ASP DAI is hooked up this can create
a powered-up DAPM graph without anything intentionally setting up a path.
This can lead to parts of the audio system powering up unexpectedly.
For example when cs35l56 is connected to cs42l43 using a codec-codec link,
this can create a complete DAPM graph which then powers-up cs42l43. But
the cs42l43 can only be clocked from its SoundWire bus so this causes a
bunch of errors in the kernel log where cs42l43 is unexpectedly powered-up
without a clock.
If the host is taking ownership of the ASP (either directly or as a
codec-to-codec link) there is no need to keep the mixer settings that the
firmware wrote. The driver has ALSA controls for setting these using
standard Linux mechanisms. So if the machine driver hooks up the ASP the
ASP mixers are initialized to "None" (no input). This prevents unintended
DAPM-graph power-ups, and means the initial state of the mixers is
always going to be None.
Since the initial state of the mixers can vary from system to system and
potentially between firmware upgrades, no use-case manager can currently
assume that cs35l56 has a known initial state. The firmware could just as
easily default them to "None" as to any input source. So defaulting them
to "None" in the driver is not increasing the entropy of the system.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240613132527.46537-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
With ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in sound/soc/amd/renoir/snd-acp3x-rn.o
WARNING: modpost: missing MODULE_DESCRIPTION() in sound/soc/amd/yc/snd-soc-acp6x-mach.o
WARNING: modpost: missing MODULE_DESCRIPTION() in sound/soc/amd/acp/snd-acp-i2s.o
WARNING: modpost: missing MODULE_DESCRIPTION() in sound/soc/amd/acp/snd-acp-pdm.o
WARNING: modpost: missing MODULE_DESCRIPTION() in sound/soc/amd/acp/snd-acp-legacy-common.o
WARNING: modpost: missing MODULE_DESCRIPTION() in sound/soc/amd/acp/snd-acp-pci.o
WARNING: modpost: missing MODULE_DESCRIPTION() in sound/soc/amd/ps/snd-soc-ps-mach.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20240612-md-sound-soc-amd-v1-1-ad1de0409c11@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It was reported that recent fix for memory corruption during topology
load, causes corruption in other cases. Instead of being overeager with
checking topology, assume that it is properly formatted and just
duplicate strings.
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Closes: https://lore.kernel.org/linux-sound/171812236450.201359.3019210915105428447.b4-ty@kernel.org/T/#m8c4bd5abf453960fde6f826c4b7f84881da63e9d
Suggested-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20240613090126.841189-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add debounce time in headset type detection for better performance.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Link: https://lore.kernel.org/r/7e502e9a9dd94122a1b60deb5ceb60fb@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the ipc_prepare() callback fails for a module instance, on error rewind
we must skip the ipc_unprepare() call for ones that has positive use count.
The positive use count means that the module instance is in active use, it
cannot be unprepared.
The issue affects capture direction paths with branches (single dai with
multiple PCMs), the affected widgets are in the shared part of the paths.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20240612121203.15468-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Jai Luthra <j-luthra@ti.com>:
This series fixes two patches:
1. Fix the dmaengine API usage by calling dmaengine_synchronize() after
dmaengine_terminate_async() when xrun events occur in application
2. Use the McASP AFIFO property from DT to refine the period size,
instead of hardcoding minimum to 64 samples
|
|
Convert the WM8804 audio codec bindings to DT schema.
Signed-off-by: Animesh Agarwal <animeshagarwal28@gmail.com>
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240611122258.47406-1-animeshagarwal28@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Convert the WM8782 audio codec bindings to DT schema.
Signed-off-by: Animesh Agarwal <animeshagarwal28@gmail.com>
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240611124405.63427-1-animeshagarwal28@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Convert the dummy SPDIF receiver bindings to DT schema.
Signed-off-by: Animesh Agarwal <animeshagarwal28@gmail.com>
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240606041212.78428-1-animeshagarwal28@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This accidentally returns success instead of -EINVAL.
Fixes: c91d0c2e198d ("ASoC: samsung: midas_wm1811: Add GPIO-based headset jack detection")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Artur Weber <aweber.kernel@gmail.com>
Link: https://lore.kernel.org/r/01590109-cf27-404b-88ff-b42bb73ca1c6@moroto.mountain
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When cs35l56 is connected via cs42l43 there isn't an ACPI node for the
cs35l56 so all properties are under the cs42l43 ACPI node. We're adding
a property as a way for the cs42l43 driver to pass this info in via a
software node.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240611132556.1557075-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set driver name to "HDMI". This simplifies the code and gets rid of
the following error messages:
ASoC: driver name too long 'HDMI 58040000.encoder' -> 'HDMI_58040000_e'
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20240610125847.773394-1-primoz.fiser@norik.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The minimum period size was enforced to 64 as older devices integrating
McASP with EDMA used an internal FIFO of 64 samples.
With UDMA based platforms this internal McASP FIFO is optional, as the
DMA engine internally does some buffering which is already accounted for
when registering the platform. So we should read the actual FIFO
configuration (txnumevt/rxnumevt) instead of hardcoding frames.min to
64.
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240611-asoc_next-v3-2-fcfd84b12164@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Sometimes the stream may be stopped due to XRUN events, in which case
the userspace can call snd_pcm_drop() and snd_pcm_prepare() to stop and
start the stream again.
In these cases, we must wait for the DMA channel to synchronize before
marking the stream as prepared for playback, as the DMA channel gets
stopped by drop() without any synchronization. Make sure the ALSA core
synchronizes the DMA channel by adding a sync_stop() hook.
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Link: https://lore.kernel.org/r/20240611-asoc_next-v3-1-fcfd84b12164@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:
Replace or drop the legacy header that is subject to remove.
Not all of them were compile-tested, the series might have
hidden compilation errors.
|
|
Merge series from Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>:
Originally reported here:
https://github.com/thesofproject/avs-topology-xml/issues/22#issuecomment-2127892605
There is various level of failure there, first of all when topology
loads routes, it points directly into FW file, but it may be freed after
topology load. After fixing the above, when avs driver parses topology
it should allocate its own memory, as target strings can be shorter than
needed. Also clean up soc_tplg_dapm_graph_elems_load() a bit.
|
|
Convert the AK4554 sound codec bindings to DT schema.
Signed-off-by: Animesh Agarwal <animeshagarwal28@gmail.com>
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240607055725.38057-1-animeshagarwal28@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
The acpi_get_local_address() helper assumes a 32-bit ADR is used. If
we want to use this helper for SoundWire/SDCA ASoC codecs, we need an
extension where the native 64-bits are used. This patchset suggests a
new helper, acpi_get_local_address() may be renamed if desired in a
folow-up patch.
The path of least resistance would be to merge this patchset in the
ASoC tree, since I have additional changes for ASoC/SDCA (SoundWire
Device Class) that depend on the new helper.
Pierre-Louis Bossart (3):
ACPI: utils: introduce acpi_get_local_u64_address()
soundwire: slave: simplify code with acpi_get_local_u64_address()
ALSA: hda: intel-sdw-acpi: use acpi_get_local_u64_address()
drivers/acpi/utils.c | 22 ++++++++++++++++------
drivers/soundwire/slave.c | 13 ++++---------
include/linux/acpi.h | 1 +
sound/hda/intel-sdw-acpi.c | 6 +++---
4 files changed, 24 insertions(+), 18 deletions(-)
--
2.43.0
|
|
Merge series from Mohammad Rafi Shaik <quic_mohs@quicinc.com>:
This patchset adds support for Qualcomm WCD9370/WCD9375 codec.
Qualcomm WCD9370/WCD9375 Codec is a standalone Hi-Fi audio codec IC
connected over SoundWire. This device has two SoundWire devices, RX and
TX respectively supporting 3 x ADCs, ClassH, Ear, Aux PA, 2xHPH,
6 DMICs and MBHC.
For codec driver to be functional it would need both tx and rx Soundwire devices
to be up and this is taken care by using device component framework and device-links
are used to ensure proper pm dependencies. Ex tx does not enter suspend
before rx or codec is suspended.
This patchset along with other SoundWire patches on the list
have been tested on QCM6490 IDP device.
|
|
Convert the OMAP4+ McPDM bindings from txt to yaml (dtschema).
Drop ti,hwmods property as it is not needed since the sysc conversion.
Add dma, dma-names, reg-names properties to match the DTS so as to not
break the already existing ABI.
Also update example node to match the existing node in the DTS.
Signed-off-by: Mithil Bavishi <bavishimithil@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240608095305.2887-1-bavishimithil@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it directly, replace it
with what is really being used.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240605221446.2624964-7-andriy.shevchenko@linux.intel.com
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it directly, replace it
with what is really being used.
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240605221446.2624964-6-andriy.shevchenko@linux.intel.com
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
of_gpio.h is deprecated and subject to remove.
The driver doesn't use it directly, replace it
with what is really being used.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240605221446.2624964-5-andriy.shevchenko@linux.intel.com
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
of_gpio.h is deprecated and subject to remove. The drivers in question
don't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240605221446.2624964-4-andriy.shevchenko@linux.intel.com
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
of_gpio.h is deprecated and subject to remove. The drivers in question
don't use it, simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240605221446.2624964-3-andriy.shevchenko@linux.intel.com
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
of_gpio.h is deprecated and subject to remove. The drivers in question
don't use it, simply remove the unused header.
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240605221446.2624964-2-andriy.shevchenko@linux.intel.com
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Now we have a helper so there's no need to open-code.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240528192936.16180-4-pierre-louis.bossart@linux.intel.com
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Now we have a helper so there's no need to open-code.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240528192936.16180-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ACPI _ADR is a 64-bit value. We changed the definitions in commit
ca6f998cf9a2 ("ACPI: bus: change _ADR representation to 64 bits") but
some helpers still assume the value is a 32-bit value.
This patch adds a new helper to extract the full 64-bits. The existing
32-bit helper is kept for backwards-compatibility and cases where the
_ADR is known to fit in a 32-bit value.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240528192936.16180-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds audio routing for both playback and capture and
Makefile and Kconfigs changes for wcd937x.
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Co-developed-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Link: https://lore.kernel.org/r/20240524035535.3119208-8-quic_mohs@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds required dapm widgets for capture path.
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Co-developed-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Link: https://lore.kernel.org/r/20240524035535.3119208-7-quic_mohs@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds required dapm widgets for playback.
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Co-developed-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Link: https://lore.kernel.org/r/20240524035535.3119208-6-quic_mohs@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds basic controls found in WCD9370/WCD9375 codec.
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Co-developed-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Link: https://lore.kernel.org/r/20240524035535.3119208-5-quic_mohs@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds basic SoundWire codec driver to support for
WCD9370/WCD9375 TX and RX devices.
The WCD9370/WCD9375 has Multi Button Headset Control hardware to
support Headset insertion, type detection, 8 headset buttons detection,
Over Current detection and Impedence measurements.
This patch adds support for this using wcd-mbhc apis.
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Co-developed-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Link: https://lore.kernel.org/r/20240524035535.3119208-4-quic_mohs@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds support to SoundWire devices on WCD9370/WCD9375 Codec.
The WCD9370/WCD9375 Soundwire devices will be used by the
main WCD9370/WCD9375 Audio Codec driver to access registers
and configure Soundwire RX and TX ports.
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Co-developed-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Link: https://lore.kernel.org/r/20240524035535.3119208-3-quic_mohs@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document the Qualcomm WCD9370/WCD9375 Audio Codec and the
Soundwire devices than can be found on Qualcomm QCM6490 based platforms.
The Qualcomm WCD9370/WCD9375 Audio Codec communicates
with the host SoC over 2 Soundwire links to provide:
- 3 TX ADC paths with 4 differential AMIC inputs
- 6 DMIC inputs that are shared with AMIC input
- 4 Microphone BIAS
- RX paths with 4 PAs – HPHL/R, EAR and AUX
- Stereo Headphone output
- MBHC engine for Headset Detection
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Co-developed-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240524035535.3119208-2-quic_mohs@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When headphones are plugged in, they appear absent; when they are removed,
they appear present.
Add a specific entry in bytcr_rt5640 for this device
Signed-off-by: Thomas GENTY <tomlohave@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20240608170251.99936-1-tomlohave@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Instead of using very long macro name, assign it to shorter variable
and use it instead. While doing that, we can reduce multiple if checks
using this define to one.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20240603102818.36165-5-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The routes are allocated with kzalloc(), so all fields are zeroed by
default, skip unnecessary assignments.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20240603102818.36165-4-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Instead of overriding existing memory strings that may be too short,
just allocate needed memory and point the route at it.
Reported-by: Jason Montleon <jmontleo@redhat.com>
Link: https://github.com/thesofproject/avs-topology-xml/issues/22#issuecomment-2127892605
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20240603102818.36165-3-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Most users after parsing a topology file, release memory used by it, so
having pointer references directly into topology file contents is wrong.
Use devm_kmemdup(), to allocate memory as needed.
Reported-by: Jason Montleon <jmontleo@redhat.com>
Link: https://github.com/thesofproject/avs-topology-xml/issues/22#issuecomment-2127892605
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20240603102818.36165-2-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Update copies of kernel headers, which resulted in support for the
new 'mseal' syscall, SUBVOL statx return mask bit, RISC-V and PPC
prctls, fcntl's DUPFD_QUERY, POSTED_MSI_NOTIFICATION IRQ vector,
'map_shadow_stack' syscall for x86-32.
- Revert perf.data record memory allocation optimization that ended up
causing a regression, work is being done to re-introduce it in the
next merge window.
- Fix handling of minimal vmlinux.h file used with BPF's CO-RE when
interrupting the build.
* tag 'perf-tools-fixes-for-v6.10-2-2024-06-09' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
perf bpf: Fix handling of minimal vmlinux.h file when interrupting the build
Revert "perf record: Reduce memory for recording PERF_RECORD_LOST_SAMPLES event"
tools headers arm64: Sync arm64's cputype.h with the kernel sources
tools headers uapi: Sync linux/stat.h with the kernel sources to pick STATX_SUBVOL
tools headers UAPI: Update i915_drm.h with the kernel sources
tools headers UAPI: Sync kvm headers with the kernel sources
tools arch x86: Sync the msr-index.h copy with the kernel sources
tools headers: Update the syscall tables and unistd.h, mostly to support the new 'mseal' syscall
perf trace beauty: Update the arch/x86/include/asm/irq_vectors.h copy with the kernel sources to pick POSTED_MSI_NOTIFICATION
perf beauty: Update copy of linux/socket.h with the kernel sources
tools headers UAPI: Sync fcntl.h with the kernel sources to pick F_DUPFD_QUERY
tools headers UAPI: Sync linux/prctl.h with the kernel sources
tools include UAPI: Sync linux/stat.h with the kernel sources
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC fixes from Borislav Petkov:
- Convert PCI core error codes to proper error numbers since latter get
propagated all the way up to the module loading functions
* tag 'edac_urgent_for_v6.10_rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/igen6: Convert PCIBIOS_* return codes to errnos
EDAC/amd64: Convert PCIBIOS_* return codes to errnos
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One fix for the SiFive PRCI clocks so that the device boots again.
This driver was registering clkdev lookups that were always going to
be useless. This wasn't a problem until clkdev started returning an
error in these cases, causing this driver to fail probe, and thus boot
to fail because clks are essential for most drivers. The fix is
simple, don't use clkdev because this is a DT based system where
clkdev isn't used"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sifive: Do not register clkdevs for PRCI clocks
|
|
Pull smb client fixes from Steve French:
"Two small smb3 client fixes:
- fix deadlock in umount
- minor cleanup due to netfs change"
* tag '6.10-rc2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Don't advance the I/O iterator before terminating subrequest
smb: client: fix deadlock in smb2_find_smb_tcon()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Benjamin Tissoires:
- fix potential read out of bounds in hid-asus (Andrew Ballance)
- fix endian-conversion on little endian systems in intel-ish-hid (Arnd
Bergmann)
- A couple of new input event codes (Aseda Aboagye)
- errors handling fixes in hid-nvidia-shield (Chen Ni), hid-nintendo
(Christophe JAILLET), hid-logitech-dj (José Expósito)
- current leakage fix while the device is in suspend on a i2c-hid
laptop (Johan Hovold)
- other assorted smaller fixes and device ID / quirk entry additions
* tag 'for-linus-2024060801' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: Ignore battery for ELAN touchscreens 2F2C and 4116
HID: i2c-hid: elan: fix reset suspend current leakage
dt-bindings: HID: i2c-hid: elan: add 'no-reset-on-power-off' property
dt-bindings: HID: i2c-hid: elan: add Elan eKTH5015M
dt-bindings: HID: i2c-hid: add dedicated Ilitek ILI2901 schema
input: Add support for "Do Not Disturb"
input: Add event code for accessibility key
hid: asus: asus_report_fixup: fix potential read out of bounds
HID: logitech-hidpp: add missing MODULE_DESCRIPTION() macro
HID: intel-ish-hid: fix endian-conversion
HID: nintendo: Fix an error handling path in nintendo_hid_probe()
HID: logitech-dj: Fix memory leak in logi_dj_recv_switch_to_dj_mode()
HID: core: remove unnecessary WARN_ON() in implement()
HID: nvidia-shield: Add missing check for input_ff_create_memless
HID: intel-ish-hid: Fix build error for COMPILE_TEST
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix the initial state of the save button in 'make gconfig'
- Improve the Kconfig documentation
- Fix a Kconfig bug regarding property visibility
- Fix build breakage for systems where 'sed' is not installed in /bin
- Fix a false warning about missing MODULE_DESCRIPTION()
* tag 'kbuild-fixes-v6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
modpost: do not warn about missing MODULE_DESCRIPTION() for vmlinux.o
kbuild: explicitly run mksysmap as sed script from link-vmlinux.sh
kconfig: remove wrong expr_trans_bool()
kconfig: doc: document behavior of 'select' and 'imply' followed by 'if'
kconfig: doc: fix a typo in the note about 'imply'
kconfig: gconf: give a proper initial state to the Save button
kconfig: remove unneeded code for user-supplied values being out of range
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- fixes for the new ipu6 driver (and related fixes to mei csi driver)
- fix a double debugfs remove logic at mgb4 driver
- a documentation fix
* tag 'media/v6.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: intel/ipu6: add csi2 port sanity check in notifier bound
media: intel/ipu6: update the maximum supported csi2 port number to 6
media: mei: csi: Warn less verbosely of a missing device fwnode
media: mei: csi: Put the IPU device reference
media: intel/ipu6: fix the buffer flags caused by wrong parentheses
media: intel/ipu6: Fix an error handling path in isys_probe()
media: intel/ipu6: Move isys_remove() close to isys_probe()
media: intel/ipu6: Fix some redundant resources freeing in ipu6_pci_remove()
media: Documentation: v4l: Fix ACTIVE route flag
media: mgb4: Fix double debugfs remove
|
