| Age | Commit message (Collapse) | Author |
|---|
|
Upon setting the cmode on 6390 and 6390X, the associated serdes
interfaces must be powered off/on.
Both 6390X and 6390 share code to do so, but it currently uses the 6390
specific helper mv88e6390_serdes_power() to disable and enable the
serdes interface.
This call will fail silently on 6390X when trying so set a 10G interface
such as XAUI or RXAUI, since mv88e6390_serdes_power() internally grabs
the lane number based on modes supported by the 6390, and returns 0 when
getting -ENODEV as a lane number.
Using mv88e6390x_serdes_power() should be safe here, since we explicitly
rule-out all ports but the 9 and 10, and because modes supported by 6390
ports 9 and 10 are a subset of those supported on 6390X.
This was tested on 6390X using RXAUI mode.
Fixes: 364e9d7776a3 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an entry to the quirks-table to for usb-audio to recognize the
Microbook II (although it only exposes vendor interfaces). A simple boot
quirk is also implemented to set up the sample rate and make sure that
no audio urbs are sent before the device is ready.
This patch only provides audio playback and capture at 96kHz sample
rate. Notice the following shortcomings:
- The sample rate is currently hardcoded to 96k although the device also
supports 48k and 44.1k.
- The various mixer controls of the MicroBook are not made available.
- The keep-iface control should be on by default because the device
shuts down whenever the altsetting is reset which is usually unwanted.
(I don't know the best way to do this)
- The communication format used by the MicroBook for sample rate setting
and also other setup has been reverse engineered by looking at the
usbmon output while running the windows driver through virtualbox. In
this patch the first byte of every message is set to \0 while in the
observed communications the first byte acts as a "message-counter"
increasing its value with every message sent. Leaving it at \0 does
not seem to affect the device.
Signed-off-by: Manuel Reinhardt <manuel.rhdt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Replace hard coded function name register_blkdev with __func__, to
improve robustness and to conform to the Linux kernel coding
style. Issue found using checkpatch.
Signed-off-by: Keyur Patel <iamkeyur96@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
handler implemented
For an AHCI controller with AHCI_HFLAG_MULTI_MSI flag set, we may get the
following log, regardless of whether a custom irq handler was implemented
or not:
[ 14.700238] ahci 0000:74:03.0: both AHCI_HFLAG_MULTI_MSI flag set and custom irq handler implemented
This is because we can set hpriv->irq_handler to
ahci_single_level_irq_intr() if not already set, in
ahci_init_one()->ahci_pci_save_initial_config()->ahci_save_initial_config().
Stop having this warn being misleading by adding a check for
hpriv->irq_handler != ahci_single_level_irq_intr.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
genlmsg_reply can fail, so propagate its return code
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/block/floppy.c: In function 'request_done':
drivers/block/floppy.c:2233:24: warning:
variable 'q' set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
null_handle_bio() erroneously uses the bio_op macro
which masks respective request flag bits including REQ_FUA
out thus failing the check.
Fix by checking bio->bi_opf directly.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
'ip' can switch network namespaces internally and then run a given
command relative to that namespace without the need to fork and exec
another ip instance. Update all references of the form:
ip netns exec "$testns" ip ...
to
ip -netns "$testns" ...
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If __device_add_disk-->bdi_register_owner-->bdi_register-->
bdi_register_va-->device_create_vargs fails, bdi->dev is still
NULL, __device_add_disk-->register_disk will visit bdi->dev->kobj.
This patch fixes that.
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
guard_bio_eod() can truncate a segment in bio to allow it to do IO on
odd last sectors of a device.
It already checks if the IO starts past EOD, but it does not consider
the possibility of an IO request starting within device boundaries can
contain more than one segment past EOD.
In such cases, truncated_bytes can be bigger than PAGE_SIZE, and will
underflow bvec->bv_len.
Fix this by checking if truncated_bytes is lower than PAGE_SIZE.
This situation has been found on filesystems such as isofs and vfat,
which doesn't check the device size before mount, if the device is
smaller than the filesystem itself, a readahead on such filesystem,
which spans EOD, can trigger this situation, leading a call to
zero_user() with a wrong size possibly corrupting memory.
I didn't see any crash, or didn't let the system run long enough to
check if memory corruption will be hit somewhere, but adding
instrumentation to guard_bio_end() to check truncated_bytes size, was
enough to see the error.
The following script can trigger the error.
MNT=/mnt
IMG=./DISK.img
DEV=/dev/loop0
mkfs.vfat $IMG
mount $IMG $MNT
cp -R /etc $MNT &> /dev/null
umount $MNT
losetup -D
losetup --find --show --sizelimit 16247280 $IMG
mount $DEV $MNT
find $MNT -type f -exec cat {} + >/dev/null
Kudos to Eric Sandeen for coming up with the reproducer above
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Replace set->map[0] with set->map[HCTX_TYPE_DEFAULT] to avoid hardcoding.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Julian Wiedmann says:
====================
s390/qeth: updates 2019-02-28
please apply one more qeth patch series for net-next. This eliminates
some of the quirks in our reset code, and slims down the internal
state machine.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that qeth always uses dev_close() to shutdown the interface, we can
trust the locking and remove some custom state checks.
qeth_l?_stop_card() is no longer called for a card in UP state, so remove
the checks there too. This basically makes the UP state obsolete, so rip
out the whole thing (except for the sysfs-visible string).
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It makes no difference whether we
1. manually disarm the HW trap and call the offline code with
recovery_mode == 1, or
2. call the offline code with recovery_mode == 0, and let it disarm the
HW trap for us.
So consolidate the two code paths in the suspend callback.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The qeth-wide workqueue is now only used by a single caller to schedule
close_dev work. Just put it on a system queue instead.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recovery code already runs in a kthread, we don't have to defer the
offlining further.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
smatch complains that __qeth_l3_set_offline() first accesses card->dev,
and then later checks whether the pointer is valid.
Since commit d3d1b205e89f ("s390/qeth: allocate netdevice early"), the
pointer is _always_ valid - that patch merely missed to remove this one
check.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When resetting an interface ("recovery"), qeth currently attempts to
elide the call to dev_close(). We initially only call .ndo_close to
quiesce the data path, and then offline & online the ccwgroup device.
If the reset succeeded, a call to .ndo_open then resumes the data path
along with some internal setup (dev_addr validation, RX modeset) that
dev_open() would have usually triggered.
dev_close() only gets called (via the close_dev worker) if the reset
action fails.
It's unclear whether this was initially done due to locking concerns, or
rather to execute the reset transparently. Either way, temporarily
closing the interface without dev_close() is fragile, and means we're
susceptible to various races and unexpected behaviour. For instance:
- Bypassing dev_deactivate_many() means that the qdiscs are not set to
__QDISC_STATE_DEACTIVATED. Consequently any intermittent TX completion
can wake up the txq, resulting in calls to .ndo_start_xmit while the
data path is down. We have custom state checking to detect this case
and drop such packets.
- Because the IFF_UP flag doesn't reflect the interface's actual state
during a reset, we have custom state checking in .ndo_open and
.ndo_close to guard against invalid calls.
- Considering that the reset might take a considerable amount of time
(in particular if an IO fails and we end up waiting for its timeout), we
_do_ want NETDEV_GOING_DOWN and NETDEV_DOWN events so that components
like bonding, team, bridge, macvlan, vlan, ... can take appropriate
action.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In its attempt to run only the minimal amount of tear down steps,
qeth_l2_stop_card() fails to reset the "is dev_addr registered?" flag
in some rare scenarios. But a future change to the tear down sequence
would cause us to _always_ hit this issue, so patch it up before that
code lands.
Fix it by unconditionally clearing the flag bit. This also allows us to
remove the additional cleanup step in qeth_dev_layer2_store().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When setting a L2 qeth device online, enable the HW trap as soon as the
control plane is available. This allows us to catch any error that
occurs during the very first commands.
In the same spirit, the offline code should disable the HW trap as the
very first step of its processing.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The offline code uses a specific RECOVER state to indicate that the
interface should be brought up when a qeth device is set online again.
Rather than having a specific card-state for this, just put it in an
internal flag bit and set the state to DOWN. When working with the
card's state transitions, this reduces the complexity quite a bit.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The switch maintains u64 counters for the number of octets sent and
received. These are kept as two u32's which need to be combined. Fix
the combing, which wrongly worked on u16's.
Fixes: 80c4627b2719 ("dsa: mv88x6xxx: Refactor getting a single statistic")
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Occasionally, during the disconnection procedure on XenBus which
includes hash cache deinitialization there might be some packets
still in-flight on other processors. Handling of these packets includes
hashing and hash cache population that finally results in hash cache
data structure corruption.
In order to avoid this we prevent hashing of those packets if there
are no queues initialized. In that case RCU protection of queues guards
the hash cache as well.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without hardware pnetid support there must currently be a pnet
table configured to determine the IB device port to be used for SMC
RDMA traffic. This patch enables a setup without pnet table, if
the used handshake interface belongs already to a RoCE port.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to only iterate in chunks of PAGE_SIZE or less in
bvec_iter_advance, given that the callers pass in the chunk length that
they are operating on - either that already is less than PAGE_SIZE
because they do classic page-based iteration, or it is larger because
the caller operates on multi-page bvecs.
This should help shaving off a few cycles of the I/O hot path.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Dongdong reported a deadlock triggered by a hotplug event during a sysfs
"remove" operation:
pciehp 0000:00:0c.0:pcie004: Slot(0-1): Link Up
# echo 1 > 0000:00:0c.0/remove
PME and hotplug share an MSI/MSI-X vector. The sysfs "remove" side is:
remove_store
pci_stop_and_remove_bus_device_locked
pci_lock_rescan_remove
pci_stop_and_remove_bus_device
...
pcie_pme_remove
pcie_pme_suspend
synchronize_irq # wait for hotplug IRQ handler
pci_unlock_rescan_remove
The hotplug side is:
pciehp_ist
pciehp_handle_presence_or_link_change
pciehp_configure_device
pci_lock_rescan_remove # wait for pci_unlock_rescan_remove()
INFO: task bash:10913 blocked for more than 120 seconds.
# ps -ax |grep D
PID TTY STAT TIME COMMAND
10913 ttyAMA0 Ds+ 0:00 -bash
14022 ? D 0:00 [irq/745-pciehp]
# cat /proc/14022/stack
__switch_to+0x94/0xd8
pci_lock_rescan_remove+0x20/0x28
pciehp_configure_device+0x30/0x140
pciehp_handle_presence_or_link_change+0x324/0x458
pciehp_ist+0x1dc/0x1e0
# cat /proc/10913/stack
__switch_to+0x94/0xd8
synchronize_irq+0x8c/0xc0
pcie_pme_suspend+0xa4/0x118
pcie_pme_remove+0x20/0x40
pcie_port_remove_service+0x3c/0x58
...
pcie_port_device_remove+0x2c/0x48
pcie_portdrv_remove+0x68/0x78
pci_device_remove+0x48/0x120
...
pci_stop_bus_device+0x84/0xc0
pci_stop_and_remove_bus_device_locked+0x24/0x40
remove_store+0xa4/0xb8
dev_attr_store+0x44/0x60
sysfs_kf_write+0x58/0x80
It is incorrect to call pcie_pme_suspend() from pcie_pme_remove() for two
reasons.
First, pcie_pme_suspend() calls synchronize_irq(), which will wait for the
native hotplug interrupt handler as well as for the PME one, because they
share one IRQ (as per the spec). That may deadlock if hotplug is signaled
while pcie_pme_remove() is running and the latter calls
pci_lock_rescan_remove() before the former.
Second, if pcie_pme_suspend() figures out that wakeup needs to be enabled
for the port, it will return without disabling the interrupt as expected by
pcie_pme_remove() which was overlooked by commit c7b5a4e6e8fb ("PCI / PM:
Fix native PME handling during system suspend/resume").
To fix that, rework pcie_pme_remove() to disable the PME interrupt, clear
its status and prevent the PME worker function from re-enabling it before
calling free_irq() on it, which should be sufficient.
Fixes: c7b5a4e6e8fb ("PCI / PM: Fix native PME handling during system suspend/resume")
Link: https://lore.kernel.org/linux-pci/c7697e7c-e1af-13e4-8491-0a3996e6ab5d@huawei.com
Reported-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bhelgaas: add URL and deadlock details from Dongdong]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Fix buffer overflow observed when running perf test.
The overflow is when trying to evaluate "1ULL << (64 - 1)" which is
resulting in -9223372036854775808 which overflows the 20 character
buffer.
If is possible this bug has been reported before but I still don't see
any fix checked in:
See: https://www.spinics.net/lists/linux-perf-users/msg07714.html
Reported-by: Michael Sartain <mikesart@fastmail.com>
Reported-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Tony Jones <tonyj@suse.de>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Fixes: f7d82350e597 ("tools/events: Add files to create libtraceevent.a")
Link: http://lkml.kernel.org/r/20190228015532.8941-1-tonyj@suse.de
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Zero-copy callback flag is not yet set on frag list skb at the moment
xenvif_handle_frag_list() returns -ENOMEM. This eventually results in
leaking grant ref mappings since xenvif_zerocopy_callback() is never
called for these fragments. Those eventually build up and cause Xen
to kill Dom0 as the slots get reused for new mappings:
"d0v0 Attempt to implicitly unmap a granted PTE c010000329fce005"
That behavior is observed under certain workloads where sudden spikes
of page cache writes coexist with active atomic skb allocations from
network traffic. Additionally, rework the logic to deal with frag_list
deallocation in a single place.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As per RFC 8033, it is sufficient for the drop probability
decay factor to have a value of (1 - 1/64) instead of 98%.
This avoids the need to do slow division.
Suggested-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to Documentation/core-api/printk-formats.rst, size_t should be
printed with %zu, rather than %Zu.
In addition, using %Zu triggers a warning on clang (-Wformat-extra-args):
net/sctp/chunk.c:196:25: warning: data argument not used by format string [-Wformat-extra-args]
__func__, asoc, max_data);
~~~~~~~~~~~~~~~~^~~~~~~~~
./include/linux/printk.h:440:49: note: expanded from macro 'pr_warn_ratelimited'
printk_ratelimited(KERN_WARNING pr_fmt(fmt), ##__VA_ARGS__)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~
./include/linux/printk.h:424:17: note: expanded from macro 'printk_ratelimited'
printk(fmt, ##__VA_ARGS__); \
~~~ ^
Fixes: 5b5e0928f742 ("lib/vsprintf.c: remove %Z support")
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Matthias Maennich <maennich@google.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It can be reproduced by following steps:
1. virtio_net NIC is configured with gso/tso on
2. configure nginx as http server with an index file bigger than 1M bytes
3. use tc netem to produce duplicate packets and delay:
tc qdisc add dev eth0 root netem delay 100ms 10ms 30% duplicate 90%
4. continually curl the nginx http server to get index file on client
5. BUG_ON is seen quickly
[10258690.371129] kernel BUG at net/core/skbuff.c:4028!
[10258690.371748] invalid opcode: 0000 [#1] SMP PTI
[10258690.372094] CPU: 5 PID: 0 Comm: swapper/5 Tainted: G W 5.0.0-rc6 #2
[10258690.372094] RSP: 0018:ffffa05797b43da0 EFLAGS: 00010202
[10258690.372094] RBP: 00000000000005ea R08: 0000000000000000 R09: 00000000000005ea
[10258690.372094] R10: ffffa0579334d800 R11: 00000000000002c0 R12: 0000000000000002
[10258690.372094] R13: 0000000000000000 R14: ffffa05793122900 R15: ffffa0578f7cb028
[10258690.372094] FS: 0000000000000000(0000) GS:ffffa05797b40000(0000) knlGS:0000000000000000
[10258690.372094] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[10258690.372094] CR2: 00007f1a6dc00868 CR3: 000000001000e000 CR4: 00000000000006e0
[10258690.372094] Call Trace:
[10258690.372094] <IRQ>
[10258690.372094] skb_to_sgvec+0x11/0x40
[10258690.372094] start_xmit+0x38c/0x520 [virtio_net]
[10258690.372094] dev_hard_start_xmit+0x9b/0x200
[10258690.372094] sch_direct_xmit+0xff/0x260
[10258690.372094] __qdisc_run+0x15e/0x4e0
[10258690.372094] net_tx_action+0x137/0x210
[10258690.372094] __do_softirq+0xd6/0x2a9
[10258690.372094] irq_exit+0xde/0xf0
[10258690.372094] smp_apic_timer_interrupt+0x74/0x140
[10258690.372094] apic_timer_interrupt+0xf/0x20
[10258690.372094] </IRQ>
In __skb_to_sgvec(), the skb->len is not equal to the sum of the skb's
linear data size and nonlinear data size, thus BUG_ON triggered.
Because the skb is cloned and a part of nonlinear data is split off.
Duplicate packet is cloned in netem_enqueue() and may be delayed
some time in qdisc. When qdisc len reached the limit and returns
NET_XMIT_DROP, the skb will be retransmit later in write queue.
the skb will be fragmented by tso_fragment(), the limit size
that depends on cwnd and mss decrease, the skb's nonlinear
data will be split off. The length of the skb cloned by netem
will not be updated. When we use virtio_net NIC and invoke skb_to_sgvec(),
the BUG_ON trigger.
To fix it, netem returns NET_XMIT_SUCCESS to upper stack
when it clones a duplicate packet.
Fixes: 35d889d1 ("sch_netem: fix skb leak in netem_enqueue()")
Signed-off-by: Sheng Lan <lansheng@huawei.com>
Reported-by: Qin Ji <jiqin.ji@huawei.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we are not able to reach firmware, enter debugging mode that will
help us to get adapter logs.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
T6 adapters support outer UDP checksum offload for
encapsulated packets, hence enabling netdev feature flag
NETIF_F_GSO_UDP_TUNNEL_CSUM.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GRO is done by cxgb4/cxgb4vf. Hence set NETIF_F_GRO flag for
both cxgb4/cxgb4vf.
Cleaned up VLAN netdev features in cxgb4vf. Also fixed
NETIF_F_HIGHDMA being set unconditionally for vlan netdev
features.
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Building a preprocessed source file for arm64 now always produces
a warning with clang because of the page_to_virt() macro assigning
a variable to itself.
Adding a new temporary variable avoids this issue.
Fixes: 2813b9c02962 ("kasan, mm, arm64: tag non slab memory allocated via pagealloc")
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Changed the driver to use the kernel's own implementation.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These changes fixed a checkpatch error for space required before the
open brace '{' as well as a warning for suspect code indent for
conditional statements.
Signed-off-by: Oscar Gomez Fuente <oscargomezf@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When ARCH_MXC get enabled, ARM64_ERRATUM_845719 will be selected and
this warning will happen when COMPAT isn't set.
WARNING: unmet direct dependencies detected for ARM64_ERRATUM_845719
Depends on [n]: COMPAT [=n]
Selected by [y]:
- ARCH_MXC [=y]
Rework to add 'if COMPAT' before ARM64_ERRATUM_845719 gets selected,
since ARM64_ERRATUM_845719 depends on COMPAT.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
UML supports enabling OF, and is useful for running the device tree
tests, so add support for unflattening device tree blobs so we can
actually use it.
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The NEON recovery code was modeled after the x86 SIMD code, and for
some reason, that code uses a 16 bit wide signed shift and a mask to
perform what amounts to a 8 bit unsigned shift. So fold the ops
together.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Clang warns: vector initializers are not compatible with NEON intrinsics
in big endian mode [-Wnonportable-vector-initialization]
While this is usually the case, it's not an issue for this case since
we're initializing the uint8x16_t (16x uint8_t's) with the same value.
Instead, use vdupq_n_u8 which both compilers lower into a single movi
instruction: https://godbolt.org/z/vBrgzt
This avoids the static storage for a constant value.
Link: https://github.com/ClangBuiltLinux/linux/issues/214
Suggested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Add vendor prefix for feiyang, known as
Shenzhen Fly Young Technology Co.,LTD. a known producer for LCD modules.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Add vendor prefix for techstar, known as
Shenzhen Techstar Electronics Co., Ltd. a known producer for LCD modules.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Add missing semicolon in example for Sitronix ST7735R display panels.
Cc: Rob Herring <robh@kernel.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
This function is only used in of_reserved_mem.c, and never overridden
despite the __weak marker.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Add -T and --annotations command line arguments to dtx_diff. These
arguments will be passed through to dtc. dtc will then add source
location annotations to its output.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Add missing dt-binding documentation for lm75 hwmon sensor.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Ensure that inX() provides the same ordering guarantees as readX()
by hooking up __io_par() so that it maps directly to __iormb().
Reported-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The definitions of the __io_[p]ar() macros in asm-generic/io.h take the
value returned by the preceding I/O read as an argument so that
architectures can use this to create order with a subsequent delayX()
routine using a dependency.
Update the riscv barrier definitions to match, although the argument
is currently unused.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The inX() and readX() I/O accessors must enforce ordering against
subsequent calls to the delay() routines, so that a read-back from a
device can be used to postpone a subsequent write to the same device.
On some architectures, including arm64, this ordering can only be
achieved by creating a dependency on the value returned by the I/O
accessor operation, so we need to pass the value we read to the
__io_par() and __io_ar() macros in these cases.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
