| Age | Commit message (Collapse) | Author |
|---|
|
Prior this commit, when the struct socket object was being released,
the UMEM did not have its reference count decreased. Instead, this was
done in the struct sock sk_destruct function.
There is no reason to keep the UMEM reference around when the socket
is being orphaned, so in this patch the xdp_put_mem is called in the
xsk_release function. This results in that the xsk_destruct function
can be removed!
Note that, it still holds that a struct xsk_sock reference might still
linger in the XSKMAP after the UMEM is released, e.g. if a user does
not clear the XSKMAP prior to closing the process. This sock will be
in a "released" zombie like state, until the XSKMAP is removed.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Ido Schimmel says:
====================
mlxsw: Make driver more robust
In recent months we fixed several bugs in the driver that could have
been avoided by re-evaluating some of the involved code paths and by
introducing relevant and comprehensive test cases.
This patchset tries to do that by introducing a set of small and mostly
non-functional changes in addition to a new test. I have further
improvements in mind, but they can be done in a different set.
Patch #1 makes sure we correctly sanitize upper devices of a VLAN
interface.
Patch #2 removes an unexpected behavior from the driver, in which routes
configured on a VLAN interface will cease being offloaded after certain
operations.
Patch #3 is a small cleanup.
Patch #4 simplifies the driver by removing reference counting from VLAN
entries configured on a port.
Patches #5-#6 simplify linking/unlinking from a bridge, especially when
LAG and VLAN devices are involved. They make both operations symmetric
even when ports are unlinked from a bridged LAG device.
Patch #7-#9 make router interface (RIF) deletion more robust by removing
reliance on device chain to indicate whether a NETDEV_DOWN event in the
inet{,6}addr notification chains should be processed. This is due to the
fact that IP addresses can be flushed from a netdev after it was
unlinked from its lower device.
Patch #10 adds a new test to for valid and invalid configurations over
mlxsw ports. Some of the test cases are derived from recent fixes. I
expect that more test cases will be added over time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new test that is focused on rtnetlink configuration. Its purpose
is to test valid and invalid (as deemed by mlxsw) configurations and
make sure that they succeed / fail without producing a trace.
Some of the test cases are derived from recent fixes in order to make
sure that the fixed bugs are not introduced again.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previous patches tried to make RIF deletion more robust and avoid
use-after-free situations.
As another precaution, hold a reference on a RIF's netdev and release it
when the RIF is deleted.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the past we had multiple instances where RIFs were not properly
deleted.
One of the reasons for leaking a RIF was that at the time when IP
addresses were flushed from the respective netdev (prompting the
destruction of the RIF), the netdev was no longer a mlxsw upper. This
caused the inet{,6}addr notification blocks to ignore the NETDEV_DOWN
event and leak the RIF.
Instead of checking whether the netdev is our upper when an IP address
is removed, we can instead check if the netdev has a RIF configured.
To look up a RIF we need to access mlxsw private data, so the patch
stores the notification blocks inside a mlxsw struct. This then allows
us to use container_of() and extract the required private data.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Next patch is going to make RIF deletion more robust by removing
reliance on fragile mlxsw_sp_lower_get(). This is because a netdev is
not necessarily our upper anymore when its IP addresses are flushed.
The inet{,6}addr notification blocks are going to resolve 'struct
mlxsw_sp' using container_of(), but the functions they call still use
mlxsw_sp_lower_get().
As a preparation for the next patch, propagate 'struct mlxsw_sp' down to
the functions called from the notification blocks and remove reliance on
mlxsw_sp_lower_get().
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a LAG device or a VLAN device on top of it is enslaved to a bridge,
the driver propagates the CHANGEUPPER event to the LAG's slaves.
This causes each physical port to increase the reference count of the
internal representation of the bridge port by calling
mlxsw_sp_port_bridge_join().
However, when a port is removed from a LAG, the corresponding leave()
function is not called and the reference count is not decremented. This
leads to ugly hacks such as mlxsw_sp_bridge_port_should_destroy() that
try to understand if the bridge port should be destroyed even when its
reference count is not 0.
Instead, make sure that when a port is unlinked from a LAG it would see
the same events as if the LAG (or its uppers) were unlinked from a
bridge.
The above is achieved by walking the LAG's uppers when a port is
unlinked and calling mlxsw_sp_port_bridge_leave() for each upper that is
enslaved to a bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b3529af6bb0d ("spectrum: Reference count VLAN entries") started
reference counting port-VLAN entries in a similar fashion to the 8021q
driver.
However, this is not actually needed and only complicates things.
Instead, the driver should forbid the creation of a VLAN on a port if
this VLAN already exists. This would also solve the issue fixed by the
mentioned commit.
Therefore, remove the get()/put() API and use create()/destroy()
instead.
One place that needs special attention is VLAN addition in a VLAN-aware
bridge via switchdev operations. In case the VLAN flags (e.g., 'pvid')
are toggled, then the VLAN entry already exists. To prevent the driver
from wrongly returning EEXIST, the driver is changed to check in the
prepare phase whether the entry already exists and only returns an error
in case it is not associated with the correct bridge port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 993107fea5ee ("mlxsw: spectrum_switchdev: Fix VLAN device
deletion via ioctl") I fixed a bug caused by the fact that the driver
views differently the deletion of a VLAN device when it is deleted via
an ioctl and netlink.
Instead of relying on a specific order of events (device being
unregistered vs. VLAN filter being updated), simply make sure that the
driver performs the necessary cleanup when the VLAN device is unlinked,
which always happens before the other two events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function is no longer used. Remove it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when a RIF is constructed on top of a FID, the RIF increments
the FID's reference count and the RIF is destroyed when the FID's
reference count drops to 1. This effectively means that when no local
ports are member in the FID, the FID is destroyed regardless if the
router port is a member in the FID or not.
The above can lead to the unexpected behavior in which routes using a
VLAN interface as their nexthop device are no longer offloaded after the
last local port leaves the corresponding VLAN (FID).
Example:
# ip -4 route show dev br0.10
192.0.2.0/24 proto kernel scope link src 192.0.2.1 offload
# bridge vlan del vid 10 dev swp3
# ip -4 route show dev br0.10
192.0.2.0/24 proto kernel scope link src 192.0.2.1
After the patch, the route is offloaded before and after the VLAN is
removed from local port 'swp3', as the RIF corresponding to 'br0.10'
continues to exists.
In order to remove RIFs' reliance on the underlying FID's reference
count, we need to add a reference count to sub-port RIFs, which are RIFs
that correspond to physical ports and their uppers (e.g., LAG devices).
In this case, each {Port, VID} ('struct mlxsw_sp_port_vlan') needs to
hold a reference on the RIF. For example:
bond0.10
|
bond0
|
+-------+
| |
swp1 swp2
Both {Port 1, VID 10} and {Port 2, VID 10} will hold a reference on the
RIF corresponding to 'bond0.10'. When the last reference is dropped, the
RIF will be destroyed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, only VRF and macvlan uppers are supported on top of VLAN
device configured over a bridge, so make sure the driver forbids other
uppers.
Note that enslavement to a VRF is handled earlier in the notification
block, so there is no need to check for a VRF upper here.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported the use of uninitialized udp6_addr::sin6_scope_id.
We can just set ::sin6_scope_id to zero, as tunnels are unlikely
to use an IPv6 address that needs a scope id and there is no
interface to bind in this context.
For net-next, it looks different as we have cfg->bind_ifindex there
so we can probably call ipv6_iface_scope_id().
Same for ::sin6_flowinfo, tunnels don't use it.
Fixes: 8024e02879dd ("udp: Add udp_sock_create for UDP tunnels to open listener socket")
Reported-by: syzbot+c56449ed3652e6720f30@syzkaller.appspotmail.com
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When sending broadcast message on high load system, there are a lot of
unnecessary packets restranmission. That issue was caused by missing in
initial criteria for retransmission.
To prevent this happen, just initialize this criteria for retransmission
in next 10 milliseconds.
Fixes: 31c4f4cc32f7 ("tipc: improve broadcast retransmission algorithm")
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tuong Lien says:
====================
tipc: tracepoints and trace_events in TIPC
The patch series is the first step of introducing a tracing framework in
TIPC, which will assist in collecting complete & plentiful data for post
analysis, even in the case of a single failure occurrence e.g. when the
failure is unreproducible.
The tracing code in TIPC utilizes the powerful kernel tracepoints, trace
events features along with particular dump functions to trace the TIPC
object data and events (incl. bearer, link, socket, node, etc.).
The tracing code should generate zero-load to TIPC when the trace events
are not enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit adds the new trace_event for TIPC bearer, L2 device event:
trace_tipc_l2_device_event()
Also, it puts the trace at the tipc_l2_device_event() function, then
the device/bearer events and related info can be traced out during
runtime when needed.
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit adds the new trace_events for TIPC node object:
trace_tipc_node_create()
trace_tipc_node_delete()
trace_tipc_node_lost_contact()
trace_tipc_node_timeout()
trace_tipc_node_link_up()
trace_tipc_node_link_down()
trace_tipc_node_reset_links()
trace_tipc_node_fsm_evt()
trace_tipc_node_check_state()
Also, enables the traces for the following cases:
- When a node is created/deleted;
- When a node contact is lost;
- When a node timer is timed out;
- When a node link is up/down;
- When all node links are reset;
- When node state is changed;
- When a skb comes and node state needs to be checked/updated.
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit adds the new trace_events for TIPC socket object:
trace_tipc_sk_create()
trace_tipc_sk_poll()
trace_tipc_sk_sendmsg()
trace_tipc_sk_sendmcast()
trace_tipc_sk_sendstream()
trace_tipc_sk_filter_rcv()
trace_tipc_sk_advance_rx()
trace_tipc_sk_rej_msg()
trace_tipc_sk_drop_msg()
trace_tipc_sk_release()
trace_tipc_sk_shutdown()
trace_tipc_sk_overlimit1()
trace_tipc_sk_overlimit2()
Also, enables the traces for the following cases:
- When user creates a TIPC socket;
- When user calls poll() on TIPC socket;
- When user sends a dgram/mcast/stream message.
- When a message is put into the socket 'sk_receive_queue';
- When a message is released from the socket 'sk_receive_queue';
- When a message is rejected (e.g. due to no port, invalid, etc.);
- When a message is dropped (e.g. due to wrong message type);
- When socket is released;
- When socket is shutdown;
- When socket rcvq's allocation is overlimit (> 90%);
- When socket rcvq + bklq's allocation is overlimit (> 90%);
- When the 'TIPC_ERR_OVERLOAD/2' issue happens;
Note:
a) All the socket traces are designed to be able to trace on a specific
socket by either using the 'event filtering' feature on a known socket
'portid' value or the sysctl file:
/proc/sys/net/tipc/sk_filter
The file determines a 'tuple' for what socket should be traced:
(portid, sock type, name type, name lower, name upper)
where:
+ 'portid' is the socket portid generated at socket creating, can be
found in the trace outputs or the 'tipc socket list' command printouts;
+ 'sock type' is the socket type (1 = SOCK_TREAM, ...);
+ 'name type', 'name lower' and 'name upper' are the service name being
connected to or published by the socket.
Value '0' means 'ANY', the default tuple value is (0, 0, 0, 0, 0) i.e.
the traces happen for every sockets with no filter.
b) The 'tipc_sk_overlimit1/2' event is also a conditional trace_event
which happens when the socket receive queue (and backlog queue) is
about to be overloaded, when the queue allocation is > 90%. Then, when
the trace is enabled, the last skbs leading to the TIPC_ERR_OVERLOAD/2
issue can be traced.
The trace event is designed as an 'upper watermark' notification that
the other traces (e.g. 'tipc_sk_advance_rx' vs 'tipc_sk_filter_rcv') or
actions can be triggerred in the meanwhile to see what is going on with
the socket queue.
In addition, the 'trace_tipc_sk_dump()' is also placed at the
'TIPC_ERR_OVERLOAD/2' case, so the socket and last skb can be dumped
for post-analysis.
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit adds the new trace_events for TIPC link object:
trace_tipc_link_timeout()
trace_tipc_link_fsm()
trace_tipc_link_reset()
trace_tipc_link_too_silent()
trace_tipc_link_retrans()
trace_tipc_link_bc_ack()
trace_tipc_link_conges()
And the traces for PROTOCOL messages at building and receiving:
trace_tipc_proto_build()
trace_tipc_proto_rcv()
Note:
a) The 'tipc_link_too_silent' event will only happen when the
'silent_intv_cnt' is about to reach the 'abort_limit' value (and the
event is enabled). The benefit for this kind of event is that we can
get an early indication about TIPC link loss issue due to timeout, then
can do some necessary actions for troubleshooting.
For example: To trigger the 'tipc_proto_rcv' when the 'too_silent'
event occurs:
echo 'enable_event:tipc:tipc_proto_rcv' > \
events/tipc/tipc_link_too_silent/trigger
And disable it when TIPC link is reset:
echo 'disable_event:tipc:tipc_proto_rcv' > \
events/tipc/tipc_link_reset/trigger
b) The 'tipc_link_retrans' or 'tipc_link_bc_ack' event is useful to
trace TIPC retransmission issues.
In addition, the commit adds the 'trace_tipc_list/link_dump()' at the
'retransmission failure' case. Then, if the issue occurs, the link
'transmq' along with the link data can be dumped for post-analysis.
These dump events should be enabled by default since it will only take
effect when the failure happens.
The same approach is also applied for the faulty case that the
validation of protocol message is failed.
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As for the sake of debugging/tracing, the commit enables tracepoints in
TIPC along with some general trace_events as shown below. It also
defines some 'tipc_*_dump()' functions that allow to dump TIPC object
data whenever needed, that is, for general debug purposes, ie. not just
for the trace_events.
The following trace_events are now available:
- trace_tipc_skb_dump(): allows to trace and dump TIPC msg & skb data,
e.g. message type, user, droppable, skb truesize, cloned skb, etc.
- trace_tipc_list_dump(): allows to trace and dump any TIPC buffers or
queues, e.g. TIPC link transmq, socket receive queue, etc.
- trace_tipc_sk_dump(): allows to trace and dump TIPC socket data, e.g.
sk state, sk type, connection type, rmem_alloc, socket queues, etc.
- trace_tipc_link_dump(): allows to trace and dump TIPC link data, e.g.
link state, silent_intv_cnt, gap, bc_gap, link queues, etc.
- trace_tipc_node_dump(): allows to trace and dump TIPC node data, e.g.
node state, active links, capabilities, link entries, etc.
How to use:
Put the trace functions at any places where we want to dump TIPC data
or events.
Note:
a) The dump functions will generate raw data only, that is, to offload
the trace event's processing, it can require a tool or script to parse
the data but this should be simple.
b) The trace_tipc_*_dump() should be reserved for a failure cases only
(e.g. the retransmission failure case) or where we do not expect to
happen too often, then we can consider enabling these events by default
since they will almost not take any effects under normal conditions,
but once the rare condition or failure occurs, we get the dumped data
fully for post-analysis.
For other trace purposes, we can reuse these trace classes as template
but different events.
c) A trace_event is only effective when we enable it. To enable the
TIPC trace_events, echo 1 to 'enable' files in the events/tipc/
directory in the 'debugfs' file system. Normally, they are located at:
/sys/kernel/debug/tracing/events/tipc/
For example:
To enable the tipc_link_dump event:
echo 1 > /sys/kernel/debug/tracing/events/tipc/tipc_link_dump/enable
To enable all the TIPC trace_events:
echo 1 > /sys/kernel/debug/tracing/events/tipc/enable
To collect the trace data:
cat trace
or
cat trace_pipe > /trace.out &
To disable all the TIPC trace_events:
echo 0 > /sys/kernel/debug/tracing/events/tipc/enable
To clear the trace buffer:
echo > trace
d) Like the other trace_events, the feature like 'filter' or 'trigger'
is also usable for the tipc trace_events.
For more details, have a look at:
Documentation/trace/ftrace.txt
MAINTAINERS | add two new files 'trace.h' & 'trace.c' in tipc
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code has 2 problems. It assumes that the RX ring for
the loopback packet is combined with the TX ring. This is not
true if the ethtool channels are set to non-combined mode. The
second problem is that it won't work on 57500 chips without
adjusting the logic to get the proper completion ring (cpr) pointer.
Fix both issues by locating the proper cpr pointer through the RX
ring.
Fixes: e44758b78ae8 ("bnxt_en: Use bnxt_cp_ring_info struct pointer as parameter for RX path.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Florian Westphal says:
====================
sk_buff: add extension infrastructure
TL;DR:
- objdiff shows no change if CONFIG_XFRM=n && BR_NETFILTER=n
- small size reduction when one or both options are set
- no changes in ipsec performance
Changes since v1:
- Allocate entire extension space from a kmem_cache.
- Avoid atomic_dec_and_test operation on skb_ext_put() for refcnt == 1 case.
(similar to kfree_skbmem() fclone_ref use).
This adds an optional extension infrastructure, with ispec (xfrm) and
bridge netfilter as first users.
The third (future) user is Multipath TCP which is still out-of-tree.
MPTCP needs to map logical mptcp sequence numbers to the tcp sequence
numbers used by individual subflows.
This DSS mapping is read/written from tcp option space on receive and
written to tcp option space on transmitted tcp packets that are part of
and MPTCP connection.
Extending skb_shared_info or adding a private data field to skb fclones
doesn't work for incoming skb, so a different DSS propagation method would
be required for the receive side.
mptcp has same requirements as secpath/bridge netfilter:
1. extension memory is released when the sk_buff is free'd.
2. data is shared after cloning an skb (clone inherits extension)
3. adding extension to an skb will COW the extension buffer if needed.
Two new members are added to sk_buff:
1. 'active_extensions' byte (filling a hole), telling which extensions
are available for this skb.
This has two purposes.
a) avoids the need to initialize the pointer.
b) allows to "delete" an extension by clearing its bit
value in ->active_extensions.
While it would be possible to store the active_extensions byte
in the extension struct instead of sk_buff, there is one problem
with this:
When an extension has to be disabled, we can always clear the
bit in skb->active_extensions. But in case it would be stored in the
extension buffer itself, we might have to COW it first, if
we are dealing with a cloned skb. On kmalloc failure we would
be unable to turn an extension off.
2. extension pointer, located at the end of the sk_buff.
If the active_extensions byte is 0, the pointer is undefined,
it is not initialized on skb allocation.
This adds extra code to skb clone and free paths (to deal with
refcount/free of extension area) but this replaces similar code that
manages skb->nf_bridge and skb->sp structs in the followup patches of
the series.
It is possible to add support for extensions that are not preseved on
clones/copies:
1. define a bitmask of all extensions that need copy/cow on clone
2. change __skb_ext_copy() to check
->active_extensions & SKB_EXT_PRESERVE_ON_CLONE
3. set clone->active_extensions to 0 if test is false.
This isn't done here because all extensions that get added here
need the copy/cow semantics.
Last patch converts skb->sp, secpath information gets stored as
new SKB_EXT_SEC_PATH, so the 'sp' pointer is removed from skbuff.
Extra code added to skb clone and free paths (to deal with refcount/free
of extension area) replaces the existing code that does the same for
skb->nf_bridge and skb->secpath.
I don't see any other in-tree users that could benefit from this
infrastructure, it doesn't make sense to add an extension just for the sake
of a single flag bit (like skb->nf_trace).
Adding a new extension is a good fit if all of the following are true:
1. Data is related to the skb/packet aggregate
2. Data should be freed when the skb is free'd
3. Data is not going to be relevant/needed in normal case (udp, tcp,
forwarding workloads, ...)
4. There are no fancy action(s) needed on clone/free, such as callbacks
into kernel modules.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove skb->sp and allocate secpath storage via extension
infrastructure. This also reduces sk_buff by 8 bytes on x86_64.
Total size of allyesconfig kernel is reduced slightly, as there is
less inlined code (one conditional atomic op instead of two on
skb_clone).
No differences in throughput in following ipsec performance tests:
- transport mode with aes on 10GB link
- tunnel mode between two network namespaces with aes and null cipher
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
secpath_set is a wrapper for secpath_dup that will not perform
an allocation if the secpath attached to the skb has a reference count
of one, i.e., it doesn't need to be COW'ed.
Also, secpath_dup doesn't attach the secpath to the skb, it leaves
this to the caller.
Use secpath_set in places that immediately assign the return value to
skb.
This allows to remove skb->sp without touching these spots again.
secpath_dup can eventually be removed in followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
reduce noise when skb->sp is removed later in the series.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Will reduce noise when skb->sp is removed later in this series.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
... so this won't have to be changed when skb->sp goes away.
v2: no changes, preserve ack.
Acked-by: Shannon Nelson <shannon.lee.nelson@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Will avoid touching this when sp pointer is removed from sk_buff struct.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use skb_sec_path and secpath_exists helpers where possible.
This reduces noise in followup patch that removes skb->sp pointer.
v2: no changes, preseve acks from v1.
Acked-by: Shannon Nelson <shannon.lee.nelson@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_sec_path gains 'const' qualifier to avoid
xt_policy.c: 'skb_sec_path' discards 'const' qualifier from pointer target type
same reasoning as previous conversions: Won't need to touch these
spots anymore when skb->sp is removed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Future patch will remove skb->sp pointer.
To reduce noise in those patches, move existing helper to
sk_buff and use it in more places to ease skb->sp replacement later.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It can only return 0 (success) or -ENOMEM.
Change return value to a pointer to secpath struct.
This avoids direct access to skb->sp:
err = secpath_set(skb);
if (!err) ..
skb->sp-> ...
Becomes:
sp = secpath_set(skb)
if (!sp) ..
sp-> ..
This reduces noise in followup patch which is going to remove skb->sp.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This converts the bridge netfilter (calling iptables hooks from bridge)
facility to use the extension infrastructure.
The bridge_nf specific hooks in skb clone and free paths are removed, they
have been replaced by the skb_ext hooks that do the same as the bridge nf
allocations hooks did.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds an optional extension infrastructure, with ispec (xfrm) and
bridge netfilter as first users.
objdiff shows no changes if kernel is built without xfrm and br_netfilter
support.
The third (planned future) user is Multipath TCP which is still
out-of-tree.
MPTCP needs to map logical mptcp sequence numbers to the tcp sequence
numbers used by individual subflows.
This DSS mapping is read/written from tcp option space on receive and
written to tcp option space on transmitted tcp packets that are part of
and MPTCP connection.
Extending skb_shared_info or adding a private data field to skb fclones
doesn't work for incoming skb, so a different DSS propagation method would
be required for the receive side.
mptcp has same requirements as secpath/bridge netfilter:
1. extension memory is released when the sk_buff is free'd.
2. data is shared after cloning an skb (clone inherits extension)
3. adding extension to an skb will COW the extension buffer if needed.
The "MPTCP upstreaming" effort adds SKB_EXT_MPTCP extension to store the
mapping for tx and rx processing.
Two new members are added to sk_buff:
1. 'active_extensions' byte (filling a hole), telling which extensions
are available for this skb.
This has two purposes.
a) avoids the need to initialize the pointer.
b) allows to "delete" an extension by clearing its bit
value in ->active_extensions.
While it would be possible to store the active_extensions byte
in the extension struct instead of sk_buff, there is one problem
with this:
When an extension has to be disabled, we can always clear the
bit in skb->active_extensions. But in case it would be stored in the
extension buffer itself, we might have to COW it first, if
we are dealing with a cloned skb. On kmalloc failure we would
be unable to turn an extension off.
2. extension pointer, located at the end of the sk_buff.
If the active_extensions byte is 0, the pointer is undefined,
it is not initialized on skb allocation.
This adds extra code to skb clone and free paths (to deal with
refcount/free of extension area) but this replaces similar code that
manages skb->nf_bridge and skb->sp structs in the followup patches of
the series.
It is possible to add support for extensions that are not preseved on
clones/copies.
To do this, it would be needed to define a bitmask of all extensions that
need copy/cow semantics, and change __skb_ext_copy() to check
->active_extensions & SKB_EXT_PRESERVE_ON_CLONE, then just set
->active_extensions to 0 on the new clone.
This isn't done here because all extensions that get added here
need the copy/cow semantics.
v2:
Allocate entire extension space using kmem_cache.
Upside is that this allows better tracking of used memory,
downside is that we will allocate more space than strictly needed in
most cases (its unlikely that all extensions are active/needed at same
time for same skb).
The allocated memory (except the small extension header) is not cleared,
so no additonal overhead aside from memory usage.
Avoid atomic_dec_and_test operation on skb_ext_put()
by using similar trick as kfree_skbmem() does with fclone_ref:
If recount is 1, there is no concurrent user and we can free right away.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This pointer is going to be removed soon, so use the existing helpers in
more places to avoid noise when the removal happens.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ioana Ciornei says:
====================
dpaa2-eth: add QBMAN statistics
This patch set adds ethtool statistics for pending frames/bytes
in Rx/Tx conf FQs and number of buffers in pool.
The first patch adds support for the query APIs in the DPIO driver
while the latter actually exposes the statistics through ethtool.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add statistics for pending frames in Rx/Tx conf FQs and
number of buffers in pool. Available through ethtool -S.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add FQ (Frame Queue) and BP (Buffer Pool) query APIs that
users of QBMan can invoke to see the status of the queues
and pools that they are using.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Turn on Broadcast writes
- UNH 1.8.1 clear bias for UNH 1000BT distortion
- UNH 1.8.7 optimize pre-emphasis for 100BasTx UNH 100W fix
- Enable Token-ring during 'Coma Mode'
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Shamir Rabinovitch says:
====================
WARNING in rds_message_alloc_sgs
This patch set fix google syzbot rds bug found in linux-next.
The first patch solve the syzbot issue.
The second patch fix issue mentioned by Leon Romanovsky that
drivers should not call WARN_ON as result from user input.
syzbot bug report can be foud here: https://lkml.org/lkml/2018/10/31/28
v1->v2:
- patch 1: make rds_iov_vector fields name more descriptive (Hakon)
- patch 1: fix potential mem leak in rds_rm_size if krealloc fail
(Hakon)
v2->v3:
- patch 2: harden rds_sendmsg for invalid number of sgs (Gerd)
v3->v4
- Santosh a.b. on both patches + repost to net-dev
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
per comment from Leon in rdma mailing list
https://lkml.org/lkml/2018/10/31/312 :
Please don't forget to remove user triggered WARN_ON.
https://lwn.net/Articles/769365/
"Greg Kroah-Hartman raised the problem of core kernel API code that will
use WARN_ON_ONCE() to complain about bad usage; that will not generate
the desired result if WARN_ON_ONCE() is configured to crash the machine.
He was told that the code should just call pr_warn() instead, and that
the called function should return an error in such situations. It was
generally agreed that any WARN_ON() or WARN_ON_ONCE() calls that can be
triggered from user space need to be fixed."
in addition harden rds_sendmsg to detect and overcome issues with
invalid sg count and fail the sendmsg.
Suggested-by: Leon Romanovsky <leon@kernel.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: shamir rabinovitch <shamir.rabinovitch@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
redundant copy_from_user in rds_sendmsg system call expose rds
to issue where rds_rdma_extra_size walk the rds iovec and and
calculate the number pf pages (sgs) it need to add to the tail of
rds message and later rds_cmsg_rdma_args copy the rds iovec again
and re calculate the same number and get different result causing
WARN_ON in rds_message_alloc_sgs.
fix this by doing the copy_from_user only once per rds_sendmsg
system call.
When issue occur the below dump is seen:
WARNING: CPU: 0 PID: 19789 at net/rds/message.c:316 rds_message_alloc_sgs+0x10c/0x160 net/rds/message.c:316
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 19789 Comm: syz-executor827 Not tainted 4.19.0-next-20181030+ #101
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x244/0x39d lib/dump_stack.c:113
panic+0x2ad/0x55c kernel/panic.c:188
__warn.cold.8+0x20/0x45 kernel/panic.c:540
report_bug+0x254/0x2d0 lib/bug.c:186
fixup_bug arch/x86/kernel/traps.c:178 [inline]
do_error_trap+0x11b/0x200 arch/x86/kernel/traps.c:271
do_invalid_op+0x36/0x40 arch/x86/kernel/traps.c:290
invalid_op+0x14/0x20 arch/x86/entry/entry_64.S:969
RIP: 0010:rds_message_alloc_sgs+0x10c/0x160 net/rds/message.c:316
Code: c0 74 04 3c 03 7e 6c 44 01 ab 78 01 00 00 e8 2b 9e 35 fa 4c 89 e0 48 83 c4 08 5b 41 5c 41 5d 41 5e 41 5f 5d c3 e8 14 9e 35 fa <0f> 0b 31 ff 44 89 ee e8 18 9f 35 fa 45 85 ed 75 1b e8 fe 9d 35 fa
RSP: 0018:ffff8801c51b7460 EFLAGS: 00010293
RAX: ffff8801bc412080 RBX: ffff8801d7bf4040 RCX: ffffffff8749c9e6
RDX: 0000000000000000 RSI: ffffffff8749ca5c RDI: 0000000000000004
RBP: ffff8801c51b7490 R08: ffff8801bc412080 R09: ffffed003b5c5b67
R10: ffffed003b5c5b67 R11: ffff8801dae2db3b R12: 0000000000000000
R13: 000000000007165c R14: 000000000007165c R15: 0000000000000005
rds_cmsg_rdma_args+0x82d/0x1510 net/rds/rdma.c:623
rds_cmsg_send net/rds/send.c:971 [inline]
rds_sendmsg+0x19a2/0x3180 net/rds/send.c:1273
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg+0xd5/0x120 net/socket.c:632
___sys_sendmsg+0x7fd/0x930 net/socket.c:2117
__sys_sendmsg+0x11d/0x280 net/socket.c:2155
__do_sys_sendmsg net/socket.c:2164 [inline]
__se_sys_sendmsg net/socket.c:2162 [inline]
__x64_sys_sendmsg+0x78/0xb0 net/socket.c:2162
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x44a859
Code: e8 dc e6 ff ff 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 6b cb fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f1d4710ada8 EFLAGS: 00000297 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00000000006dcc28 RCX: 000000000044a859
RDX: 0000000000000000 RSI: 0000000020001600 RDI: 0000000000000003
RBP: 00000000006dcc20 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000297 R12: 00000000006dcc2c
R13: 646e732f7665642f R14: 00007f1d4710b9c0 R15: 00000000006dcd2c
Kernel Offset: disabled
Rebooting in 86400 seconds..
Reported-by: syzbot+26de17458aeda9d305d8@syzkaller.appspotmail.com
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: shamir rabinovitch <shamir.rabinovitch@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2018-12-19
Here's the main bluetooth-next pull request for 4.21:
- Multiple fixes & improvements for Broadcom-based controllers
- New USB ID for an Intel controller
- Support for new Broadcom controller variants
- Use DEFINE_SHOW_ATTRIBUTE to simplify debugfs code
- Eliminate confusing "last event is not cmd complete" warning message
- Added vendor suspend/resume support for H:5 (3-Wire UART) controllers
- Various other smaller improvements & fixes
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.20
Last set of fixes for 4.20. All (except the mt76 fix) of these are
important fixes to user reported problems and pretty small in size.
rtlwifi
* fix skb leak
mwifiex
* revert a commit from v4.19 due to problems with locking
mt76
* fix a potential NULL derenfence
* add entry to MAINTAINERS
iwlwifi
* fix a firmware crash which was a regression introduced in v4.20-rc4
ath10k
* fix a firmware crash with wcn3990 firmware
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have too many changes to list, highlights:
* virt_wifi - wireless control simulation on top of
another network interface
* hwsim configurability to test capabilities similar
to real hardware
* various mesh improvements
* various radiotap vendor data fixes in mac80211
* finally the nl_set_extack_cookie_u64() we talked
about previously, used for
* peer measurement APIs, right now only with FTM
(flight time measurement) for location
* made nl80211 radio/interface announcements more complete
* various new HE (802.11ax) things:
updates, TWT support, ...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just three fixes:
* fix a memory leak in an error path
* fix TXQs in interface teardown
* free fraglist if we used it internally
before returning SKB
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running the kernel in Fast RAM on Atari:
Ignoring memory chunk at 0x0:0xe00000 before the first chunk
...
Unable to handle kernel NULL pointer dereference at virtual address (ptrval)
Oops: 00000000
Modules linked in:
PC: [<0069dbac>] free_all_bootmem+0x12c/0x186
SR: 2714 SP: (ptrval) a2: 005e3314
d0: 00000000 d1: 0000000a d2: 00000e00 d3: 00000000
d4: 005e1fc0 d5: 0000001a a0: 01000000 a1: 00000000
Process swapper (pid: 0, task=(ptrval))
Frame format=7 eff addr=00000736 ssw=0505 faddr=00000736
wb 1 stat/addr/data: 0000 00000000 00000000
wb 2 stat/addr/data: 0000 00000000 00000000
wb 3 stat/addr/data: 0000 00000736 00000000
push data: 00000000 00000000 00000000 00000000
Stack from 005e1f84:
00000000 0000000a 027d3260 006b5006 00000000 00000000 00000000 00000000
0004f062 0003a220 0069e272 005e1ff8 0000054c 00000000 00e00000 00000000
00000001 00693cd8 027d3260 0004f062 0003a220 00691be6 00000000 00000000
00000000 00000000 00000000 00000000 006b5006 00000000 00690872
Call Trace: [<0004f062>] printk+0x0/0x18
[<0003a220>] parse_args+0x0/0x2d4
[<0069e272>] memblock_virt_alloc_try_nid+0x0/0xa4
[<00693cd8>] mem_init+0xa/0x5c
[<0004f062>] printk+0x0/0x18
[<0003a220>] parse_args+0x0/0x2d4
[<00691be6>] start_kernel+0x1ca/0x462
[<00690872>] _sinittext+0x872/0x11f8
Code: 7a1a eaae 2270 6db0 0061 ef14 2f01 2f03 <96a9> 0736 2203 e589 d681 e78b d6a9 0732 2f03 2f40 0034 4eb9 0069 b8d0 260e 4fef
Disabling lock debugging due to kernel taint
Kernel panic - not syncing: Attempted to kill the idle task!
As the kernel must run in the memory chunk with the lowest address,
ST-RAM is ignored, and removed from the m68k_memory[] array.
However, it is not removed from memblock, causing a crash later.
More investigation shows that there are 3 places where memory chunks are
ignored, all after the calls to memblock_add() in m68k_parse_bootinfo(),
and thus causing crashes:
1. On classic m68k CPUs with a MMU, paging_init() ignores all memory
chunks below the first chunk, cfr. above,
2. On Amigas equipped with a Zorro III bus, config_amiga() ignores all
Zorro II memory,
3. If CONFIG_SINGLE_MEMORY_CHUNK=y, m68k_parse_bootinfo() ignores all
but the first memory chunk.
Fix this by moving the calls to memblock_add() from
m68k_parse_bootinfo() to paging_init(), after all ignored memory chunks
have been removed from m68k_memory[].
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Fixes: 1008a11590b966b4 ("m68k: switch to MEMBLOCK + NO_BOOTMEM")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
For the same reason as commit 25896d073d8a ("x86/build: Fix compiler
support check for CONFIG_RETPOLINE"), you cannot put this $(error ...)
into the parse stage of the top Makefile.
Perhaps I'd propose a more sophisticated solution later, but this is
the best I can do for now.
Link: https://lkml.org/lkml/2017/12/25/211
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reported-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Reported-by: Qian Cai <cai@lca.pw>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Qian Cai <cai@lca.pw>
|
|
In case a command which completes in Command Status was sent using the
hci_cmd_send-family of APIs there would be a misleading error in the
hci_get_cmd_complete function, since the code would be trying to fetch
the Command Complete parameters when there are none.
Avoid the misleading error and silently bail out from the function in
case the received event is a command status.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
HL2.0 firmware does not support setting quiet mode. If the host driver sends
the quiet mode setting command to the HL2.0 firmware, it crashes with the below
signature.
fatal error received: err_qdi.c:456:EX:wlan_process:1:WLAN RT:207a:PC=b001b4f0
The quiet mode command support is exposed by the firmware via thermal throttle
wmi service. Enable ath10k thermal support if thermal throttle wmi service bit
is set. 10.x firmware versions support this feature by default, but
unfortunately do not advertise the support via service flags, hence have to
manually set the service flag in ath10k_core_compat_services().
Tested on QCA988X with 10.2.4.70.9-2. Also tested on WCN3990.
Co-developed-by: Govind Singh <govinds@codeaurora.org>
Co-developed-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
