| Age | Commit message (Collapse) | Author |
|---|
|
Some eMMCs from Micron have been reported to need ~800 ms timeout, while
enabling the CACHE ctrl after running sudden power failure tests. The
needed timeout is greater than what the card specifies as its generic CMD6
timeout, through the EXT_CSD register, hence the problem.
Normally we would introduce a card quirk to extend the timeout for these
specific Micron cards. However, due to the rather complicated debug process
needed to find out the error, let's simply use a minimum timeout of 1600ms,
the double of what has been reported, for all cards when enabling CACHE
ctrl.
Reported-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In commit 5320226a0512 ("mmc: core: Disable HPI for certain Hynix eMMC
cards"), then intent was to prevent HPI from being used for some eMMC
cards, which didn't properly support it. However, that went too far, as
even BKOPS and CACHE ctrl became prevented. Let's restore those parts and
allow BKOPS and CACHE ctrl even if HPI isn't supported.
Fixes: 5320226a0512 ("mmc: core: Disable HPI for certain Hynix eMMC cards")
Cc: Pratibhasagar V <pratibha@codeaurora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
During a re-initialization of the eMMC card, we may fail to re-enable HPI.
In these cases, that isn't properly reflected in the card->ext_csd.hpi_en
bit, as it keeps being set. This may cause following attempts to use HPI,
even if's not enabled. Let's fix this!
Fixes: eb0d8f135b67 ("mmc: core: support HPI send command")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
While booting with rootfs on MMC, the following warning is encountered
on OMAP4430:
omap-dma-engine 4a056000.dma-controller: DMA-API: mapping sg segment longer than device claims to support [len=69632] [max=65536]
This is because the DMA engine has a default maximum segment size of 64K
but HSMMC sets:
mmc->max_blk_size = 512; /* Block Length at max can be 1024 */
mmc->max_blk_count = 0xFFFF; /* No. of Blocks is 16 bits */
mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
mmc->max_seg_size = mmc->max_req_size;
which ends up telling the block layer that we support a maximum segment
size of 65535*512, which exceeds the advertised DMA engine capabilities.
Fix this by clamping the maximum segment size to the lower of the
maximum request size and of the DMA engine device used for either DMA
channel.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some of the SDMMC pads auto calibration values parsed from
devicetree are assigned incorrectly. This patch fixes it.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Fixes: 51b77c8ea784 ("mmc: tegra: Program pad autocal offsets from dt")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
V4_MODE is Bit-15 of SDHCI_HOST_CONTROL2 register.
Need to perform word access to this register.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Fixes: b3f80b434f72 ("mmc: sdhci: Add sd host v4 mode")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
According to the documentation in include/uapi/asm-generic/ioctl.h,
_IOW means userspace is writing and kernel is reading, and
_IOR means userspace is reading and kernel is writing.
In case of these two ioctls, kernel is writing and userspace is reading,
so they have to be _IOR instead of _IOW.
Fixes: 72cd87576d1d8 ("block: Introduce BLKGETZONESZ ioctl")
Fixes: 65e4e3eee83d7 ("block: Introduce BLKGETNRZONES ioctl")
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
|
|
Ido Schimmel says:
====================
mlxsw: spectrum_acl: Add Bloom filter support
Nir says:
Spectrum-2 uses Bloom filter to reduce the number of lookups in the
algorithmic TCAM (A-TCAM). HW performs multiple exact match lookups in a
given region using a key composed of { packet & mask, mask ID, region ID }.
The masks which are used in a region are called rule patterns or RP.
When such multiple masks are used, the A-TCAM region uses an eRP
(extended RP) table that describes which rule patterns are in use and
defines the order of the lookup. When eRP table is used in a region, one
way to reduce the number of the lookups is to consult a Bloom filter
before doing the lookup.
A Bloom filter is a space-efficient probabilistic data structure, on
which a query returns either "possibly in set" or "definitely not in
set". HW can skip a lookup if a query on the Bloom filter results a
"definitely not set" response. The mlxsw driver implements a "counting
filter" and when either a new entry is marked or the last entry is
removed it will update the HW. Update of this counting filter occurs
when rule is configured or deleted from a region.
Patch #1 adds PEABFE register which is used for setting Bloom filter
entries.
Patch #2 adds Bloom filter resources.
Patch #3 and patch #4 provide Bloom filter handling within mlxsw, by
adding initialization and logic for updating the Bloom bit vector in HW.
Patch #5 and patch #6 add required calls for Bloom filter update as part
of rule configuration flow.
Patch #7 handles transitions to and from eRP table. It uses a list to
keep A-TCAM rules in order to update rules in Bloom filter, in cases of
transitions from master mask based A-TCAM region to an eRP table based
region and vice versa.
Patch #8 removes a trick done on master RP index to a remaining RP,
since Bloom filter is updated on eRP transitions.
Finally, patch #9 activates Bloom filter mechanism in HW, by cancelling
the bypass that was configured before and the remaining three patches
are selftests that exercise the new code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The eRP table is active when there is more than a single rule
pattern. It may be that the patterns are close enough and use delta
mechanism. Bloom filter index computation is based on the values of
{rule & mask, mask ID, region ID} where the rule delta bits must be
cleared.
Add a test that exercises Bloom filter with delta mechanism.
Configure rules within delta range and pass a packet which is
supposed to hit the correct rule.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bloom filter index computation is based on the values of
{rule & mask, mask ID, region ID} and the computation also varies
according to the region key size.
Add a test that exercises the possible combinations by creating
multiple chains using different key sizes and then pass a frame that
is supposed to to produce a hit on all of the regions.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a test that exercises Bloom filter code.
Activate eRP table in the region by adding multiple rule patterns which
with very high probability use different entries in the Bloom filter.
Then send packets in order to check lookup hits on all relevant rules.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that mlxsw driver handles all aspects of updating
the Bloom filter mechanism, set bf_bypass value to false
and allow HW to use Bloom filter.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bloom filter is updated on transitions from a single rule pattern,
also called master RP, to eRP table and vice versa. Since rules are
being written to or deleted from the Bloom filter on such transitions,
it is not required to keep the same eRP bank ID for the master RP.
Change master RP index assignment so it will be assigned with zero.
This is consistent with the assignment of the first available spot
that is used for allocating eRP's indices.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bloom filter update is required only for rules which reside on an
eRP. When the region has only a single rule pattern then eRP table
is not used, however insertion of another pattern would trigger a
move to an active eRP table so it is imperative to update the Bloom
filter with all previously configured rules.
Add a method that updates Bloom filter entries for all rules
currently configured in the region, on the event of a transition
from master mask to eRP, or vice versa. For that purpose, maintain
a list of all A-TCAM rules within mlxsw_sp_acl_atcam_region.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add calls to eRP module for updating Bloom filter when a rule is
added or removed from the A-TCAM. eRP module will update the Bloom
filter only for cases in which the region has an active eRP table.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add Bloom filter update for rule insertion and rule removal scenarios.
This is done within eRP module in order to assure that Bloom filter
updates are done only for rules which are part of an eRP, as HW does not
consult Bloom filter for entries when there is a single (master) mask in
the region.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spectrum-2 HW uses Bloom filter in order to skip lookups on specific
eRPs. It uses crc-16-Msbit-first calculation over a specific layout
of a rule's key fields combined with eRP ID as well as region ID.
Per potential lookup, iff the Bloom filter entry of the calculated
index is empty, then the lookup can be skipped. Hence, the mlxsw
driver should update the Bloom filter entry per each rule insertion
or deletion when rules are part of an eRP.
Add functions for adding and deleting entries in the Bloom filter.
In order to do so also add crc-16 computation based on the specific
Spectrum-2 polynomial and a function for encoding the crc-16 input
in the manner dictated by HW implementation.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lay the foundations for Bloom filter handling. Introduce a new file for
Bloom filter actions.
Add struct mlxsw_sp_acl_bf to struct mlxsw_sp_acl_erp_core and initialize
the Bloom filter data structure. Also take care of proper destruction when
terminating.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the maximum Bloom filter logarithmic size per eRP table bank.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bloom filter is a bit vector which allows the HW a fast lookup on a
small size bit vector, that may reduce the number of lookups on the
A-TCAM memory. PEABFE register allows setting values to the bits of
the bit vector mentioned above.
Add the register to be later used in A-TCAM optimizations.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Roopa Prabhu says:
====================
rtnl fdb get
This series adds support for rtnl fdb get similar to
route get.
v2: add nda_policy, fixes to exact msgs, strict nlmsg parsing
v3: remove unnecessary attribute length checks + simplify code
as pointed out by david
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tests the below three cases of bridge fdb get:
[bridge, mac, vlan]
[bridge_port, mac, vlan, flags=[NTF_MASTER]]
[vxlandev, mac, flags=NTF_SELF]
depends on iproute2 support for bridge fdb get.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements ndo_fdb_get for a vxlan device.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements ndo_fdb_get for the bridge
fdb.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for fdb get similar to
route get. arguments can be any of the following (similar to fdb add/del/dump):
[bridge, mac, vlan] or
[bridge_port, mac, vlan, flags=[NTF_MASTER]] or
[dev, mac, [vni|vlan], flags=[NTF_SELF]]
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marek Vasut says:
====================
net: dsa: ksz: Clean up the tag code in prep for more switches
Clean up the KSZ DSA tag code in preparation for adding more switches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case the destination address is link local, add override bit into the
switch tag to let such a packet through the switch even if the port is
blocked.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Factor out common code from the tag_ksz , so that the code can be used
with other KSZ family switches which use differenly sized tags.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename the tag Kconfig option and related macros in preparation for
addition of new KSZ family switches with different tag formats.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FW team asks to be able to not support RED even if NIC is capable
of buffering for testing and experimentation. Add an opt-out flag.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent changes in the mvneta driver reworked allocation
and handling of the ingress buffers to use entire pages.
Apart from that in SW BM scenario the HW must be informed
via PRXDQS about the biggest possible incoming buffer
that can be propagated by RX descriptors.
The BufferSize field was filled according to the MTU-dependent
pkt_size value. Later change to PAGE_SIZE broke RX operation
when usin 64K pages, as the field is simply too small.
This patch conditionally limits the value passed to the BufferSize
of the PRXDQS register, depending on the PAGE_SIZE used.
On the occasion remove now unused frag_size field of the mvneta_port
structure.
Fixes: 562e2f467e71 ("net: mvneta: Improve the buffer allocation method for SWBM")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit ec49d83f245453515a9b6e88324e27bbcb69fbae.
Cause build failures when DCCP is modular.
ERROR: "inet_hashinfo2_init" [net/dccp/dccp.ko] undefined!
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to routes and rules, add protocol attribute to neighbor entries
for easier tracking of how each was created.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds coverage of DCCP to reuseport_addr_any selftest.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit d9fbc7f6431f "net: tcp: prefer listeners bound to an address"
removes port-only listener lookups. This caused segfaults in DCCP
lookups because DCCP did not initialize the (addr,port) hashtable.
This patch adds said initialization.
The only non-trivial issue here is the size of the new hashtable.
It seemed reasonable to make it match the size of the port-only
hashtable (= INET_LHTABLE_SIZE) that was used previously. Other
parameters to inet_hashinfo2_init() match those used in TCP.
Tested: syzcaller issues fixed; the second patch in the patchset
tests that DCCP lookups work correctly.
Fixes: d9fbc7f6431f "net: tcp: prefer listeners bound to an address"
Reported-by: syzcaller <syzkaller@googlegroups.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Peng Li says:
====================
net: hns: Code improvements & fixes for HNS driver
This patchset introduces some code improvements and fixes
for the identified problems in the HNS driver.
Every patch is independent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a net bridge, add eth and vnet to the bridge. The vnet is used
by a virtual machine. When ping the virtual machine from the outside
host and the virtual machine send multicast at the same time, the ping
package will lost.
The multicast package send to the eth, eth will send it to the bridge too,
and the bridge learn the mac of eth. When outside host ping the virtual
mechine, it will match the promisc entry of the eth which is not expected,
and the bridge send it to eth not to vnet, cause ping lost.
So this patch change promisc tcam entry position to the END of 512 tcam
entries, which indicate lower priority. And separate one promisc entry to
two: mc & uc, to avoid package match the wrong tcam entry.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some case, when mac enable|disable and adjust link, may cause hard to
link(or abnormal) between mac and phy. This patch adds the code for rx PCS
to avoid this bug.
Disable the rx PCS when driver disable the gmac, and enable the rx PCS
when driver enable the mac.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ntuple-filters features is forced on by chip.
But it shows "ntuple-filters: off [fixed]" when use ethtool.
This patch make it correct with "ntuple-filters: on [fixed]".
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There will be a large number of MAC pause frames on the net,
which caused tx timeout of net device. And then the net device
was reset to try to recover it. So that is not useful, and will
cause some other problems.
So need doubled ndev->watchdog_timeo if device watchdog occurred
until watchdog_timeo up to 40s and then try resetting to recover
it.
When collecting dfx information such as hardware registers when tx timeout.
Some registers for count were cleared when read. So need move this task
before update net state which also read the count registers.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1.In "hns_nic_init_irq", if request irq fail at index i,
the function return directly without releasing irq resources
that already requested.
2.In "hns_nic_net_up" after "hns_nic_init_irq",
if exceptional branch occurs, irqs that already requested
are not release.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If there are packets in hardware when changing the speed or duplex,
it may cause hardware hang up.
This patch adds the code to wait rx fbd clean up when ae stopped.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After resetting dsaf to try to repair chip error such as ecc error,
the net device will be open if net interface is up. But at this time
if there is the users set the net device up with the command ifconfig,
the net device will be opened twice consecutively.
Function napi_enable was called when open device. And Kernel panic will
be occurred if it was called twice consecutively. Such as follow:
static inline void napi_enable(struct napi_struct *n)
{
BUG_ON(!test_bit(NAPI_STATE_SCHED, &n->state));
smp_mb__before_clear_bit();
clear_bit(NAPI_STATE_SCHED, &n->state);
}
[37255.571996] Kernel panic - not syncing: BUG!
[37255.595234] Call trace:
[37255.597694] [<ffff80000008ab48>] dump_backtrace+0x0/0x1a0
[37255.603114] [<ffff80000008ad08>] show_stack+0x20/0x28
[37255.608187] [<ffff8000009c4944>] dump_stack+0x98/0xb8
[37255.613258] [<ffff8000009c149c>] panic+0x10c/0x26c
[37255.618070] [<ffff80000070f134>] hns_nic_net_up+0x30c/0x4e0
[37255.623664] [<ffff80000070f39c>] hns_nic_net_open+0x94/0x12c
[37255.629346] [<ffff80000084be78>] __dev_open+0xf4/0x168
[37255.634504] [<ffff80000084c1ac>] __dev_change_flags+0x98/0x15c
[37255.640359] [<ffff80000084c29c>] dev_change_flags+0x2c/0x68
[37255.769580] [<ffff8000008dc400>] devinet_ioctl+0x650/0x704
[37255.775086] [<ffff8000008ddc38>] inet_ioctl+0x98/0xb4
[37255.780159] [<ffff800000827b7c>] sock_do_ioctl+0x44/0x84
[37255.785490] [<ffff800000828e04>] sock_ioctl+0x248/0x30c
[37255.790737] [<ffff80000026dc6c>] do_vfs_ioctl+0x480/0x618
[37255.796156] [<ffff80000026de94>] SyS_ioctl+0x90/0xa4
[37255.801139] SMP: stopping secondary CPUs
[37255.805079] kbox: catch panic event.
[37255.809586] collected_len = 128928, LOG_BUF_LEN_LOCAL = 131072
[37255.816103] flush cache 0xffff80003f000000 size 0x800000
[37255.822192] flush cache 0xffff80003f000000 size 0x800000
[37255.828289] flush cache 0xffff80003f000000 size 0x800000
[37255.834378] kbox: no notify die func register. no need to notify
[37255.840413] ---[ end Kernel panic - not syncing: BUG!
This patchset fix this bug according to the flag NIC_STATE_DOWN.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the hip06 datasheet:
1.Six registers use wrong address:
RCB_COM_SF_CFG_INTMASK_RING
RCB_COM_SF_CFG_RING_STS
RCB_COM_SF_CFG_RING
RCB_COM_SF_CFG_INTMASK_BD
RCB_COM_SF_CFG_BD_RINT_STS
DSAF_INODE_VC1_IN_PKT_NUM_0_REG
2.The offset of DSAF_INODE_VC1_IN_PKT_NUM_0_REG should be
0x103C + 0x80 * all_chn_num
3.The offset to show the value of DSAF_INODE_IN_DATA_STP_DISC_0_REG
is wrong, so the value of DSAF_INODE_SW_VLAN_TAG_DISC_0_REG will be
overwrite
These registers are only used in "ethtool -d", so that did not cause ndev
to misfunction.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two test cases:
1. Remove the 4 modules:hns_enet_drv/hns_dsaf/hnae/hns_mdio,
and install them again, must use "ifconfig down/ifconfig up"
command pair to bring port to work.
This patch calls phy_stop function when init phy to fix this bug.
2. Remove the 2 modules:hns_enet_drv/hns_dsaf, and install them again,
all ports can not use anymore, because of the phy devices register
failed(phy devices already exists).
Phy devices are registered when hns_dsaf installed, this patch
removes them when hns_dsaf removed.
The two cases are sometimes related, fixing the second case also requires
fixing the first case, so fix them together.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the hip06 Datasheet:
1. The offset of INGRESS_SW_VLAN_TAG_DISC should be 0x1A00+4*all_chn_num
2. The offset of INGRESS_IN_DATA_STP_DISC should be 0x1A50+4*all_chn_num
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When Protocol Field Compression (PFC) is enabled, the "Protocol" field
in PPP packet will be received without leading 0x00. See section 6.5 in
RFC 1661 for details. So let's decompress protocol field if needed, the
same way it's done in drivers/net/ppp/pptp.c.
In case when "nopcomp" pppd option is not enabled, PFC (pcomp) can be
negotiated during LCP handshake, and L2TP driver in kernel will receive
PPP packets with compressed Protocol field, which in turn leads to next
error:
Protocol Rejected (unsupported protocol 0x2145)
because instead of Protocol=0x0021 in PPP packet there will be
Protocol=0x21. This patch unwraps it back to 0x0021, which fixes the
issue.
Sending the compressed Protocol field will be implemented in subsequent
patch, this one is self-sufficient.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-12-14 (VF Lag)
From Aviv Heller,
Subsequent patches introduce VF LAG, which provdies load-balancing and
high-availability capabilities for VFs associated with different
physical ports of the same Connect-X card.
This series consists of the following:
- mlx5 devcom, driver infrastructure that facilitates operations that involve
both core devices (physical functions) of the same card, to synchronize and
communicate between two driver instances of the same card.
- Infrastructure for TC rule duplication.
- Changes to LAG logic to enable its use when SR-IOV is enabled
- PFs in switchdev mode is the only mode currently supported.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sergey reported that forwarding was no longer working
if fq packet scheduler was used.
This is caused by the recent switch to EDT model, since incoming
packets might have been timestamped by __net_timestamp()
__net_timestamp() uses ktime_get_real(), while fq expects packets
using CLOCK_MONOTONIC base.
The fix is to clear skb->tstamp in forwarding paths.
Fixes: 80b14dee2bea ("net: Add a new socket option for a future transmit time.")
Fixes: fb420d5d91c1 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Sergey Matyukevich <geomatsi@gmail.com>
Tested-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
