summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-09-13arm64: dts: renesas: v3msk: add eMMC supportSergei Shtylyov
Add the eMMC chip support for the V3M Started Kit board. Based on the original (and large) patches by Vladimir Barinov. Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-09-13arm64: dts: renesas: r8a77970: add MMC supportSergei Shtylyov
Define the generic R8A77970 part of the MMC0 (SDHI2) device node. Based on the original (and large) patches by Vladimir Barinov. Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-09-13arm64: dts: renesas: r8a77965: Add OPPs table for cpu devicesDien Pham
This patch adds OPPs table for CA57{0,1} cpu devices Signed-off-by: Dien Pham <dien.pham.ry@renesas.com> Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com> Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com> Tested-by: Simon Horman <horms+renesas@verge.net.au> [simon: do not give nodes unit names as they have no bus addresses] Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-09-13arm64: dts: renesas: r8a77965: m3nulcb: Initial device treeEugeniu Rosca
Allow the bare M3-N-based ULCB board to boot. Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-09-13arm64: dts: renesas: r8a77965: Add CAN{0,1} placeholder nodesEugeniu Rosca
According to R-Car Gen3 HW manual rev1.00, R-Car M3-N has two CAN interfaces, similar to H3, M3-W and other SoCs from the same family. Add CAN placeholder nodes to avoid below DTC errors: Error: arch/arm64/boot/dts/renesas/ulcb-kf.dtsi:19.1-6 Label or path can0 not found Error: arch/arm64/boot/dts/renesas/ulcb-kf.dtsi:25.1-6 Label or path can1 not found These errors occur *after* the addition of r8a77965-m3nulcb-kf.dts. Fix them beforehand. CAN support is inspired from below commits: - v4.7 commit 308b7e4ba62e ("arm64: dts: r8a7795: Add CAN support") - v4.11 commit 909c16252415 ("arm64: dts: r8a7796: Add CAN support") - v4.12 commit bec0948e810f ("arm64: dts: r8a7796: Add reset control properties") Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> [simon: make placeholder minimal by only including reg property] Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-09-13arm64: dts: renesas: r8a77965: Attach the SYS-DMAC to the IPMMUMagnus Damm
For R-Car M3-N hook up SYS-DMAC0, SYS-DMAC1 and SYS-DMAC2 to IPMMU-DS0 and IPMMU-DS1 in same way as for R-Car M3-W. This follows the R-Car Gen3 Rev.1.00 (April 2018) datasheet. Signed-off-by: Magnus Damm <damm+renesas@opensource.se> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-09-13arm64: dts: renesas: Initial r8a774a1 SoC device treeBiju Das
Basic support for the RZ/G2M SoC. Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-09-13arm64: dts: renesas: salvator-common: adv748x: Override secondary addressesKieran Bingham
Ensure that the ADV748x device addresses do not conflict, and group them together (visually in i2cdetect) Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-09-13arm64: dts: renesas: r8a77980: add CSI2/VIN supportSergei Shtylyov
Describe the CSI2 and VIN (and their interconnections) in the R8A77980 device tree. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-09-13arm64: dts: renesas: salvator-xs: enable SATAWolfram Sang
Add the nodes to enable SATA. Note that MD12 (SW12-7) must be switched off for that to work. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-09-13arm64: dts: renesas: r8a77965: Add SATA controller nodeTakeshi Kihara
This patch adds SATA controller node for the R8A77965 SoC. Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com> [wsa: rebased to upstream base] Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-09-12arm64: dts: meson-axg-s400: Add chosen and memory nodesNeil Armstrong
Add missing chosen and memory nodes. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-09-12arm64: dts: meson-axg: use the proper compatible for ethmacNeil Armstrong
Use the correct compatible for the AXG ethernet mac node. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-09-12arm64: dts: meson-axg: s400: add pdm to the sound cardJerome Brunet
Enable the PDM input device on the S400 and it to the sound card Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-09-12arm64: dts: meson-axg: s400: add dmic codecJerome Brunet
There are 7 digital mics on the MIC daughter board attached to the s400 board, so add the digital microphone codec to its DTS Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-09-12arm64: dts: meson-axg: add pdmJerome Brunet
Add the PDM device of the axg audio subsystem Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-09-12arm64: dts: meson-gx: add dmcbus and canvas nodes.Maxime Jourdan
DMC is a small memory region with various registers, including the ones needed for the canvas module. Reviewed-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-09-12arm64: dts: meson: libretech: update board modelJerome Brunet
There is actually several different libretech board with the CC suffix so the model name is not appropriate here. Update to something more specific Reported-by: Da Xue <da@lessconfused.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-09-12arm64: dts: meson-gx: increase default shared CMA pool sizeChristian Hewitt
Devices using the new V4L2 mem2mem vdec require a larger CMA pool. As nearly all GX* devices are video/media focused and will use it, set a larger (256MB) default value. Signed-off-by: Christian Hewitt <christianshewitt@gmail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-09-12arm64: dts: meson-axg: sort nodes consistentlyJerome Brunet
Sort DT nodes by address when possible, by node node name otherwise. Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com>
2018-09-12ARM: dts: at91: sama5d4: add labels to soc dtsi for derivative boardsEugen Hristev
This adds labels to commonly used device-tree nodes so that derivative boards can avoid ahb/apb hierarchy. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-09-11arm64: dts: renesas: r8a779{7|8}0: move CAN clock nodeSergei Shtylyov
The CAN clock node should precede the "cpus" node in the R8A779{7|8}0 device trees, according to the alphanumeric node sorting rule... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-09-11arm64: dts: renesas: r8a77980: move IPMMU nodesSergei Shtylyov
The IPMMU nodes should follow the GEther node, not the CAN-FD node, according to the <unit-address> part of the startng IPMMU-DS1 node. While moving the nodes, also do sort them by label alphanumerically... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-09-11arm64: dts: renesas: r8a77990: Enable PWM for Ebisu boardYoshihiro Shimoda
This patch adds PWM device nodes and enables PWM3 and PWM5 for R-Car E3 Ebisu board. These devices are used for backlight control. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-09-11arm64: dts: renesas: r8a77980: add Cortex-A53 PMU supportSergei Shtylyov
Describe the performance monitor unit (PMU) for the Cortex-A53 cores in the R8A77980 SoC's device tree. Based on the original (and large) patch by Vladimir Barinov. Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-09-11arm64: dts: juno: Enable coresight tmc scatter gather in ETRSuzuki K Poulose
We do not enable scatter-gather mode in the TMC-ETR by default to prevent malfunctioning of systems where the ETR may not be properly connected to the memory subsystem to allow for simultaneous READ/WRITE transactions when used in SG mode. Instead we whitelist the platforms where we know that it is safe to use the mode. All revisions of Juno have a proper ETR connection and hence white list them. Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Mike Leach <mike.leach@linaro.org> Cc: Liviu Dudau <liviu.dudau@arm.com> Cc: Lorenzo Pierlisi <lorenzo.pieralisi@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
2018-09-10arm64: dts: rockchip: Add type-c port supply on rk3399-sapphire boardVicente Bergas
Add the gpio-controlled regulator and add the supply to the otg-port of phy0. Signed-off-by: Vicente Bergas <vicencb@gmail.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2018-09-10ARM: s3c24xx: Correct SD card write protect detection on Mini2440Cedric Roux
The mini2440 computer uses "active high" to signal that the "write protect" of the inserted MMC is set. The current code uses the opposite, leading to a wrong detection of write protection. The solution is simply to use ".wprotect_invert = 1" in the description of the MMC. Signed-off-by: Cedric Roux <sed@free.fr> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2018-09-10ARM: s3c24xx: Consistently use tab for indenting member assignmentsKrzysztof Kozlowski
Code was mixing spaces and tabs for indenting members in structures. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2018-09-10ARM: s3c24xx: formatting cleanup in mach-mini2440.cCedric Roux
Running: scripts/checkpatch.pl -f arch/arm/mach-s3c24xx/mach-mini2440.c revealed several errors and warnings. They were all removed, except one which is an #if 0 around the declaration of a gpio pin. This needs some more investigation and I prefer to let it here. This is not some dead code. 'printk' was replaced by 'pr_info'. Signed-off-by: Cedric Roux <sed@free.fr> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2018-09-10arm64: dts: rockchip: fix vcc_host1_5v pin assign on rk3328-rock64Katsuhiro Suzuki
This patch fixes pin assign of vcc_host1_5v. This regulator is controlled by USB20_HOST_DRV signal. ROCK64 schematic says that GPIO0_A2 pin is used as USB20_HOST_DRV. GPIO0_D3 pin is for SPDIF_TX_M0. Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2018-09-10arm64: dts: rockchip: add WiFi module support for Firefly-RK3399Shohei Maruyama
This commit adds WiFi module support for the Firefly-RK3399. Signed-off-by: Shohei Maruyama <cheat.sc.linux@outlook.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2018-09-10arm64: dts: rockchip: remove dvs2 pinctrl from pmic on rk3399-sapphireVicente Bergas
On the board DVS2 is disabled and not connected, see schematic, page 16. Signed-off-by: Vicente Bergas <vicencb@gmail.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2018-09-10arm64: dts: rockchip: Fix VCC5V0_HOST_EN on rk3399-sapphireVicente Bergas
The pin is GPIO4-D1 not GPIO1-D1, see schematic, page 15 for reference. Signed-off-by: Vicente Bergas <vicencb@gmail.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2018-09-10arm64: dts: rockchip: re-order vcc_sys on rk3399-sapphireVicente Bergas
Fix alphabetical order. Signed-off-by: Vicente Bergas <vicencb@gmail.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2018-09-10arm64: dts: juno: Update entries to match latest coresight bindingsSuzuki K Poulose
Switch to updated coresight bindings for Juno platforms. Cc: Liviu Dudau <liviu.dudau@arm.com> Acked-by: Liviu Dudau <liviu.dudau@arm.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> [sudeep.holla: minor modifications to patch title] Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
2018-09-06ARM: dts: r9a06g032: Use r9a06g032-sysctrl binding definitionsGeert Uytterhoeven
Replace the hardcoded clock indices by R9A06G032_CLK_* symbols. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Phil Edworthy <phil.edworthy@renesas.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
2018-09-05ARM: dts: bcm283x-rpi-lan7515: Enable Ethernet LEDsStefan Wahren
Since the LAN7515 on Raspberry Pi 3B+ doesn't have an EEPROM and the OTP is empty, we need to enable the Ethernet LEDs via Device Tree. Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
2018-09-04Merge tag 'socfpga_updates_for_v4.20_part1' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt SoCFPGA DTS updates for v4.20 - Rename de0_sockit to de0_nano_soc - Update NAND clocking - Set timer interrupt to edge sensitive - Stratix10 platform updates - Update devkit with correct i2c clock * tag 'socfpga_updates_for_v4.20_part1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: ARM: dts: socfpga: Rename socfpga_cyclone5_de0_{sockit,nano_soc} ARM: dts: socfpga: update NAND clocking for c5/a5 ARM: dts: arria10: update NAND clocking ARM: dts: socfpga: set timer interrupt to edge sensitive ARM: dts: socfpga: use stdout-path for chosen node arm64: dts: stratix10: i2c clock running out of spec Signed-off-by: Olof Johansson <olof@lixom.net>
2018-09-03ARM: dts: at91: tse850: drop three indentation levelsPeter Rosin
Make use of the recently added &pinctrl and &watchdog labels. This makes the whole file consistent and knowledge of the ahb/apb structure is hidden. Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-09-03ARM: dts: at91: nattis: drop three indentation levelsPeter Rosin
Make use of the recently added &pinctrl and &watchdog labels. This makes the whole file consistent and knowledge of the ahb/apb structure is hidden. Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-09-02Linux 4.19-rc2v4.19-rc2Linus Torvalds
2018-09-02Merge tag 'devicetree-fixes-for-4.19' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux Pull devicetree updates from Rob Herring: "A couple of new helper functions in preparation for some tree wide clean-ups. I'm sending these new helpers now for rc2 in order to simplify the dependencies on subsequent cleanups across the tree in 4.20" * tag 'devicetree-fixes-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: of: Add device_type access helper functions of: add node name compare helper functions of: add helper to lookup compatible child node
2018-09-02Merge tag 'armsoc-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC fixes from Olof Johansson: "First batch of fixes post-merge window: - A handful of devicetree changes for i.MX2{3,8} to change over to new panel bindings. The platforms were moved from legacy framebuffers to DRM and some development board panels hadn't yet been converted. - OMAP fixes related to ti-sysc driver conversion fallout, fixing some register offsets, no_console_suspend fixes, etc. - Droid4 changes to fix flaky eMMC probing and vibrator DTS mismerge. - Fixed 0755->0644 permissions on a newly added file. - Defconfig changes to make ARM Versatile more useful with QEMU (helps testing). - Enable defconfig options for new TI SoC platform that was merged this window (AM6)" * tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: arm64: defconfig: Enable TI's AM6 SoC platform ARM: defconfig: Update the ARM Versatile defconfig ARM: dts: omap4-droid4: Fix emmc errors seen on some devices ARM: dts: Fix file permission for am335x-osd3358-sm-red.dts ARM: imx_v6_v7_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G ARM: mxs_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G ARM: dts: imx23-evk: Convert to the new display bindings ARM: dts: imx23-evk: Move regulators outside simple-bus ARM: dts: imx28-evk: Convert to the new display bindings ARM: dts: imx28-evk: Move regulators outside simple-bus Revert "ARM: dts: imx7d: Invert legacy PCI irq mapping" arm: dts: am4372: setup rtc as system-power-controller ARM: dts: omap4-droid4: fix vibrations on Droid 4 bus: ti-sysc: Fix no_console_suspend handling bus: ti-sysc: Fix module register ioremap for larger offsets ARM: OMAP2+: Fix module address for modules using mpu_rt_idx ARM: OMAP2+: Fix null hwmod for ti-sysc debug
2018-09-02Merge branch 'x86-urgent-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 fixes from Thomas Gleixner: "Speculation: - Make the microcode check more robust - Make the L1TF memory limit depend on the internal cache physical address space and not on the CPUID advertised physical address space, which might be significantly smaller. This avoids disabling L1TF on machines which utilize the full physical address space. - Fix the GDT mapping for EFI calls on 32bit PTI - Fix the MCE nospec implementation to prevent #GP Fixes and robustness: - Use the proper operand order for LSL in the VDSO - Prevent NMI uaccess race against CR3 switching - Add a lockdep check to verify that text_mutex is held in text_poke() functions - Repair the fallout of giving native_restore_fl() a prototype - Prevent kernel memory dumps based on usermode RIP - Wipe KASAN shadow stack before rewinding the stack to prevent false positives - Move the AMS GOTO enforcement to the actual build stage to allow user API header extraction without a compiler - Fix a section mismatch introduced by the on demand VDSO mapping change Miscellaneous: - Trivial typo, GCC quirk removal and CC_SET/OUT() cleanups" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/pti: Fix section mismatch warning/error x86/vdso: Fix lsl operand order x86/mce: Fix set_mce_nospec() to avoid #GP fault x86/efi: Load fixmap GDT in efi_call_phys_epilog() x86/nmi: Fix NMI uaccess race against CR3 switching x86: Allow generating user-space headers without a compiler x86/dumpstack: Don't dump kernel memory based on usermode RIP x86/asm: Use CC_SET()/CC_OUT() in __gen_sigismember() x86/alternatives: Lockdep-enforce text_mutex in text_poke*() x86/entry/64: Wipe KASAN stack shadow before rewind_stack_do_exit() x86/irqflags: Mark native_restore_fl extern inline x86/build: Remove jump label quirk for GCC older than 4.5.2 x86/Kconfig: Fix trivial typo x86/speculation/l1tf: Increase l1tf memory limit for Nehalem+ x86/spectre: Add missing family 6 check to microcode check
2018-09-02Merge branch 'smp-urgent-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull CPU hotplug fix from Thomas Gleixner: "Remove the stale skip_onerr member from the hotplug states" * 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: cpu/hotplug: Remove skip_onerr field from cpuhp_step structure
2018-09-02Merge branch 'core-urgent-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull core fixes from Thomas Gleixner: "A small set of updates for core code: - Prevent tracing in functions which are called from trace patching via stop_machine() to prevent executing half patched function trace entries. - Remove old GCC workarounds - Remove pointless includes of notifier.h" * 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: objtool: Remove workaround for unreachable warnings from old GCC notifier: Remove notifier header file wherever not used watchdog: Mark watchdog touch functions as notrace
2018-09-02x86/pti: Fix section mismatch warning/errorRandy Dunlap
Fix the section mismatch warning in arch/x86/mm/pti.c: WARNING: vmlinux.o(.text+0x6972a): Section mismatch in reference from the function pti_clone_pgtable() to the function .init.text:pti_user_pagetable_walk_pte() The function pti_clone_pgtable() references the function __init pti_user_pagetable_walk_pte(). This is often because pti_clone_pgtable lacks a __init annotation or the annotation of pti_user_pagetable_walk_pte is wrong. FATAL: modpost: Section mismatches detected. Fixes: 85900ea51577 ("x86/pti: Map the vsyscall page if needed") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andy Lutomirski <luto@kernel.org> Link: https://lkml.kernel.org/r/43a6d6a3-d69d-5eda-da09-0b1c88215a2a@infradead.org
2018-09-01Merge tag 'omap-for-v4.19/fixes-v2-signed' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes Fixes for omap variants against v4.19-rc1 These are mostly fixes related to using ti-sysc interconnect target module driver for accessing right register offsets for sgx and cpsw and for no_console_suspend regression. There is also a droid4 emmc fix where emmc may not get detected for some models, and vibrator dts mismerge fix. And we have a file permission fix for am335x-osd3358-sm-red.dts that just got added. And we must tag RTC as system-power-controller for am437x for PMIC to shut down during poweroff. * tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: omap4-droid4: Fix emmc errors seen on some devices ARM: dts: Fix file permission for am335x-osd3358-sm-red.dts arm: dts: am4372: setup rtc as system-power-controller ARM: dts: omap4-droid4: fix vibrations on Droid 4 bus: ti-sysc: Fix no_console_suspend handling bus: ti-sysc: Fix module register ioremap for larger offsets ARM: OMAP2+: Fix module address for modules using mpu_rt_idx ARM: OMAP2+: Fix null hwmod for ti-sysc debug Signed-off-by: Olof Johansson <olof@lixom.net>
2018-09-01x86/vdso: Fix lsl operand orderSamuel Neves
In the __getcpu function, lsl is using the wrong target and destination registers. Luckily, the compiler tends to choose %eax for both variables, so it has been working so far. Fixes: a582c540ac1b ("x86/vdso: Use RDPID in preference to LSL when available") Signed-off-by: Samuel Neves <sneves@dei.uc.pt> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Andy Lutomirski <luto@kernel.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180901201452.27828-1-sneves@dei.uc.pt
generated by cgit (git 2.34.1) at 2025-09-14 07:06:00 +0000