| Age | Commit message (Collapse) | Author |
|---|
|
Add resources ABI documentation.
Signed-off-by: Arkadi Sharhsevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for hot reload. First, all the driver/core resources are
released but the PCI and devlink instances, then reset is performed
through the PCI interface. Finally the driver performs initialization.
In case of reload failure the driver is left in a partially initialized
state. Special care is taken during the driver removal in order to
properly handle this state.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now the KVD partition was static. This patch introduces the
ability to get the resource sizes via devlink. In case the resource is not
available the default configuration is used.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for getting the kvdl occupancy through the resource interface.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Connect current dpipe tables to resources. The tables are connected
in the following fashion:
1. IPv4 host -> KVD hash single
2. IPv6 host -> KVD hash double
3. Adjacency -> KVD linear
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register the KVD resources with devlink. The KVD is a memory resource
which is subdivided into three partitions which are the linear, hash
single and hash double.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a preparation stage before introducing hot reload. During the
reload process the ASIC should be resetted by accessing the PCI BAR due
to unavailability of the mailbox/emad interfaces.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hardware processes which are modeled via dpipe commonly use some
internal hardware resources. Such relation can improve the understanding
of hardware limitations. The number of resource's unit consumed per
table's entry are also provided for each table.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for performing driver hot reload.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for hardware resource abstraction over devlink. Each resource
is identified via id, furthermore it contains information regarding its
size and its related sub resources. Each resource can also provide its
current occupancy.
In some cases the sizes of some resources can be changed, yet for those
changes to take place a hot driver reload may be needed. The reload
capability will be introduced in the next patch.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a preparation before introducing resources and hot reload support.
Currently there are two global lock where one protects all devlink access,
and the second one protects devlink port access. This patch adds per devlink
instance lock which protects the internal members which are the sb/dpipe/
resource/ports. By introducing this lock the global devlink port lock can
be discarded.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mips builds with BCMA host mode enabled fail in mainline and -next
with:
In file included from include/linux/bcma/bcma.h:10:0,
from drivers/bcma/bcma_private.h:9,
from drivers/bcma/main.c:8:
include/linux/bcma/bcma_driver_pci.h:218:24: error:
field 'pci_controller' has incomplete type
Bisect points to commit d41e6858ba58c ("MIPS: Kconfig: Set default MIPS
system type as generic") as the culprit. Analysis shows that the commmit
changes PCI configuration and enables PCI_DRIVERS_GENERIC. This in turn
disables PCI_DRIVERS_LEGACY. 'struct pci_controller' is, however, only
defined if PCI_DRIVERS_LEGACY is enabled.
Ultimately that means that BCMA_DRIVER_PCI_HOSTMODE depends on
PCI_DRIVERS_LEGACY. Add the missing dependency.
Fixes: d41e6858ba58c ("MIPS: Kconfig: Set default MIPS system type as ...")
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: James Hogan <jhogan@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Make use of the new helpers for paged register access.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reenable the 64-bit window during resume.
Fixes: fa564ad96366 ("x86/PCI: Enable a 64bit BAR on AMD Family 15h (Models 00-1f, 30-3f, 60-7f)")
Reported-by: Tom St Denis <tom.stdenis@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Heiner Kallweit says:
====================
phy: add helpers for setting/clearing bits in PHY registers
Based on the recent introduction of phy_modify add helpers for setting
and clearing bits in PHY registers. First user is phylib.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use new helpers phy_set_bits / phy_clear_bits in phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on the recent introduction of phy_modify add helpers for setting
and clearing bits in PHY registers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KVM doesn't follow the SMCCC when it comes to unimplemented calls,
and inject an UNDEF instead of returning an error. Since firmware
calls are now used for security mitigation, they are becoming more
common, and the undef is counter productive.
Instead, let's follow the SMCCC which states that -1 must be returned
to the caller when getting an unknown function number.
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
Due to architecture limitations, the IBM VNIC client driver is unable
to perform MAC address changes unless the device has "logged in" to
its backing device. Currently, pending MAC changes are handled before
login, resulting in an error and failure to change the MAC address.
Moving that chunk to the end of the ibmvnic_login function, when we are
sure that it was successful, fixes that.
The MAC address can be changed when the device is up or down, so
only check if the device is in a "PROBED" state before setting the
MAC address.
Fixes: c26eba03e407 ("ibmvnic: Update reset infrastructure to support tunable parameters")
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b014e96d1abb ("PCI: Protect pci_error_handlers->reset_notify()
usage with device_lock()") resolves races between driver reset and
removal, but it introduces some new deadlock problems. If we see a
timeout while we've already started suspending, removing, or shutting
down the driver, we might see:
(a) a worker thread, running mwifiex_pcie_work() ->
mwifiex_pcie_card_reset_work() -> pci_reset_function()
(b) a removal thread, running mwifiex_pcie_remove() ->
mwifiex_free_adapter() -> mwifiex_unregister() ->
mwifiex_cleanup_pcie() -> cancel_work_sync(&card->work)
Unfortunately, mwifiex_pcie_remove() already holds the device lock that
pci_reset_function() is now requesting, and so we see a deadlock.
It's necessary to cancel and synchronize our outstanding work before
tearing down the driver, so we can't have this work wait indefinitely
for the lock.
It's reasonable to only "try" to reset here, since this will mostly
happen for cases where it's already difficult to reset the firmware
anyway (e.g., while we're suspending or powering off the system). And if
reset *really* needs to happen, we can always try again later.
Fixes: b014e96d1abb ("PCI: Protect pci_error_handlers->reset_notify() usage with device_lock()")
Cc: <stable@vger.kernel.org>
Cc: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This reverts commit b713bbf1471b56b572ce26bd02b81a85c2b007f4.
The "fix" in question does not actually fix all related problems, and it
also introduces new deadlock possibilities. Since commit b014e96d1abb
("PCI: Protect pci_error_handlers->reset_notify() usage with
device_lock()"), the race in question is actually resolved (PCIe reset
cannot happen at the same time as remove()). Instead, this "fix" just
introduces a deadlock where mwifiex_pcie_card_reset_work() is waiting on
device_lock, which is held by PCIe device remove(), which is waiting
on...mwifiex_pcie_card_reset_work().
The proper thing to do is just to fix the deadlock. Patch for this will
come separately.
Cc: Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Variable fw_ps_state is assigned a value but it is never read, hence
it is redundant and can be removed.
Cleans up clang warning:
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtcoutsrc.c:736:2:
warning: Value stored to 'fw_ps_state' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Checkpatch found these issues:
drivers/net/wireless/ath/ath10k/ce.h:324: Please use a blank line after function/struct/union/enum declarations
drivers/net/wireless/ath/ath10k/core.c:1321: Please don't use multiple blank lines
drivers/net/wireless/ath/ath10k/htt.h:1859: Please use a blank line after function/struct/union/enum declarations
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Variable section_table.size is a u32 and so cannot be less than
zero, hence the less than zero check is redundant and can be
removed.
Detected by CoverityScan, CID#1463855 ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In some rare conditions when running one PEAK USB-FD interface over
a non high-speed USB controller, one useless USB fragment might be sent.
This patch fixes the way a USB command is fragmented when its length is
greater than 64 bytes and when the underlying USB controller is not a
high-speed one.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Trivial fix to spelling mistake in warning message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Validate ie_len after the alignment padding before access the buffer
to avoid potential overflow.
Signed-off-by: Ryan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Some platform(BIOS) blocks legacy interrupts (INTx), and only allows MSI
for WLAN device. So adding a quirk to list those machines and set
use_msi automatically.
Adding the following platforms to the quirk.
Dell Inspiron 24-3460
Dell Inspiron 3472
Dell Inspiron 14-3473
Dell Vostro 3262
Dell Vostro 15-3572
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
On new Intel platforms like ApolloLake, legacy interrupt mechanism
(INTx) is not supported, so WLAN modules are not working because
interrupts are missing, therefore this patch is to add MSI support to
ath9k. With module paremeter "use_msi=1", ath9k driver would try to
use MSI instead of INTx.
Signed-off-by: Russell Hu <rhu@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add call to new generic functions that provides support via a binding
to limit the arbitration rate and/or data rate imposed by the physical
transceiver connected to the MCAN peripheral.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support for CONFIG_PM which is the new way to handle managing clocks.
Move the clock management to pm_runtime_resume() and pm_runtime_suspend()
callbacks for the driver.
CONFIG_PM is required by OMAP based devices to handle clock management.
Therefore, this allows future Texas Instruments SoCs that have the MCAN IP
to work with this driver.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
As the previous patch removed alloc_m_can_dev(), let's get rid of the
corresponding free_m_can_dev() and call free_candev() directly.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
With the version no longer required to allocate the net device, it can
be moved to probe and the alloc_m_can_dev() function can be simplified.
Therefore, move the allocation of net device to probe and change
alloc_m_can_dev() to setup_m_can_dev().
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Currently the m_can version is used to set the tx_fifo_count to 1 when
allocating the net device. However, this is redundant as a value of 1
for the tx_fifo_count needs to be provided in the bosch,mram-cfg
property of the device tree node anyway.
Therefore, remove check for version when allocating the net device.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
During test transmitting using CAN-FD at high bitrates (> 2 Mbps)
would fail. Scoping the signals I noticed that only a single bit
was being transmitted and with a bit more investigation realized the
actual MCAN IP would go back to initialization mode automatically.
It appears this issue is due to the MCAN needing to use the Transmitter
Delay Compensation Mode with the correct value for the transmitter delay
compensation offset (tdco). What impacts the tdco value isn't 100% clear
but to calculate it you use an equation defined in the MCAN User's Guide.
The user guide mentions that this register needs to be set based on clock
values, secondary sample point and the data bitrate. One of the key
variables that can't automatically be determined is the secondary
sample point (ssp). This ssp is similar to the sp but is specific to this
transmitter delay compensation mode. The guidelines for configuring
ssp is rather vague but via some CAN test it appears for DRA76x that
putting the value same as data sampling point works.
The CAN-CIA's "Bit Time Requirements for CAN FD" paper presented at
the International CAN Conference 2013 indicates that this TDC mode is
only needed for data bit rates above 2.5 Mbps. Therefore, only enable
this mode when the data bit rate is above 2.5 Mbps.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add information regarding can-transceiver binding. This is especially
important for MCAN since the IP allows CAN FD mode to run significantly
faster than what most transceivers are capable of.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Various CAN or CAN-FD IP may be able to run at a faster rate than
what the transceiver the CAN node is connected to. This can lead to
unexpected errors. However, CAN transceivers typically have fixed
limitations and provide no means to discover these limitations at
runtime. Therefore, add support for a can-transceiver node that
can be reused by other CAN peripheral drivers to determine for both
CAN and CAN-FD what the max bitrate that can be used. If the user
tries to configure CAN to pass these maximum bitrates it will throw
an error.
Also add support for reading bitrate_max via the netlink interface.
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
[nsekhar@ti.com: fix build error with !CONFIG_OF]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add documentation to describe usage of the new can-transceiver binding.
This new binding is applicable for any CAN device therefore it exists as
its own document.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Before commit:
e33a9bba85a8 ("sched/core: move IO scheduling accounting from io_schedule_timeout() into scheduler")
delayacct_blkio_end() was called after context-switching into the task which
completed I/O.
This resulted in double counting: the task would account a delay both waiting
for I/O and for time spent in the runqueue.
With e33a9bba85a8, delayacct_blkio_end() is called by try_to_wake_up().
In ttwu, we have not yet context-switched. This is more correct, in that
the delay accounting ends when the I/O is complete.
But delayacct_blkio_end() relies on 'get_current()', and we have not yet
context-switched into the task whose I/O completed. This results in the
wrong task having its delay accounting statistics updated.
Instead of doing that, pass the task_struct being woken to delayacct_blkio_end(),
so that it can update the statistics of the correct task.
Signed-off-by: Josh Snyder <joshs@netflix.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Cc: <stable@vger.kernel.org>
Cc: Brendan Gregg <bgregg@netflix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-block@vger.kernel.org
Fixes: e33a9bba85a8 ("sched/core: move IO scheduling accounting from io_schedule_timeout() into scheduler")
Link: http://lkml.kernel.org/r/1513613712-571-1-git-send-email-joshs@netflix.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Bpftool doesn't recognize BPF_PROG_TYPE_CGROUP_DEVICE programs,
so the prog show command prints the numeric type value:
$ bpftool prog show
1: type 15 name bpf_prog1 tag ac9f93dbfd6d9b74
loaded_at Jan 15/07:58 uid 0
xlated 96B jited 105B memlock 4096B
This patch defines the corresponding textual representation:
$ bpftool prog show
1: cgroup_device name bpf_prog1 tag ac9f93dbfd6d9b74
loaded_at Jan 15/07:58 uid 0
xlated 96B jited 105B memlock 4096B
Signed-off-by: Roman Gushchin <guro@fb.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Quentin Monnet <quentin.monnet@netronome.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
We cannot access the skb->_nfct field when CONFIG_NF_CONNTRACK is
disabled:
net/ipv4/netfilter/nf_defrag_ipv4.c: In function 'ipv4_conntrack_defrag':
net/ipv4/netfilter/nf_defrag_ipv4.c:83:9: error: 'struct sk_buff' has no member named '_nfct'
net/ipv6/netfilter/nf_defrag_ipv6_hooks.c: In function 'ipv6_defrag':
net/ipv6/netfilter/nf_defrag_ipv6_hooks.c:68:9: error: 'struct sk_buff' has no member named '_nfct'
Both functions already have an #ifdef for this, so let's move the
check in there.
Fixes: 902d6a4c2a4f ("netfilter: nf_defrag: Skip defrag if NOTRACK is set")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
As a side-effect of adding the module option, we now get a section
mismatch warning:
WARNING: net/ipv4/netfilter/iptable_raw.o(.data+0x1c): Section mismatch in reference from the variable packet_raw to the function .init.text:iptable_raw_table_init()
The variable packet_raw references
the function __init iptable_raw_table_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Apparently it's ok to link to a __net_init function from .rodata but not
from .data. We can address this by rearranging the logic so that the
structure is read-only again. Instead of writing to the .priority field
later, we have an extra copies of the structure with that flag. An added
advantage is that that we don't have writable function pointers with this
approach.
Fixes: 902d6a4c2a4f ("netfilter: nf_defrag: Skip defrag if NOTRACK is set")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
ipv6_defrag pulls network headers before fragment header. In case of
an error, the netfilter layer is currently dropping these packets.
This results in failure of some IPv6 standards tests which passed on
older kernels due to the netfilter framework using cloning.
The test case run here is a check for ICMPv6 error message replies
when some invalid IPv6 fragments are sent. This specific test case is
listed in https://www.ipv6ready.org/docs/Core_Conformance_Latest.pdf
in the Extension Header Processing Order section.
A packet with unrecognized option Type 11 is sent and the test expects
an ICMP error in line with RFC2460 section 4.2 -
11 - discard the packet and, only if the packet's Destination
Address was not a multicast address, send an ICMP Parameter
Problem, Code 2, message to the packet's Source Address,
pointing to the unrecognized Option Type.
Since netfilter layer now drops all invalid IPv6 frag packets, we no
longer see the ICMP error message and fail the test case.
To fix this, save the transport header. If defrag is unable to process
the packet due to RFC2460, restore the transport header and allow packet
to be processed by stack. There is no change for other packet
processing paths.
Tested by confirming that stack sends an ICMP error when it receives
these packets. Also tested that fragmented ICMP pings succeed.
v1->v2: Instead of cloning always, save the transport_header and
restore it in case of this specific error. Update the title and
commit message accordingly.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
request_module may return a positive error result from modprobe,
if we cast this to ERR_PTR this returns a garbage result (it passes
IS_ERR checks).
Fix it by ignoring modprobe return values entirely, just retry the
table lookup instead.
Reported-by: syzbot+980925dbfbc7f93bc2ef@syzkaller.appspotmail.com
Fixes: 03d13b6868a2 ("netfilter: xtables: add and use xt_request_find_table_lock")
Fixes: 20651cefd25f ("netfilter: x_tables: unbreak module auto loading")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Currently the BSP microcode update code examines the initrd very early
in the boot process. If SME is active, the initrd is treated as being
encrypted but it has not been encrypted (in place) yet. Update the
early boot code that encrypts the kernel to also encrypt the initrd so
that early BSP microcode updates work.
Tested-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180110192634.6026.10452.stgit@tlendack-t1.amdoffice.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In preparation for encrypting more than just the kernel, the encryption
support in sme_encrypt_kernel() needs to support 4KB page aligned
encryption instead of just 2MB large page aligned encryption.
Update the routines that populate the PGD to support non-2MB aligned
addresses. This is done by creating PTE page tables for the start
and end portion of the address range that fall outside of the 2MB
alignment. This results in, at most, two extra pages to hold the
PTE entries for each mapping of a range.
Tested-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180110192626.6026.75387.stgit@tlendack-t1.amdoffice.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In preparation for encrypting more than just the kernel during early
boot processing, centralize the use of the PMD flag settings based
on the type of mapping desired. When 4KB aligned encryption is added,
this will allow either PTE flags or large page PMD flags to be used
without requiring the caller to adjust.
Tested-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180110192615.6026.14767.stgit@tlendack-t1.amdoffice.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In preparation for follow-on patches, combine the PGD mapping parameters
into a struct to reduce the number of function arguments and allow for
direct updating of the next pagetable mapping area pointer.
Tested-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180110192605.6026.96206.stgit@tlendack-t1.amdoffice.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Clean up the use of PUSH and POP and when registers are saved in the
__enc_copy() assembly function in order to improve the readability of the code.
Move parameter register saving into general purpose registers earlier
in the code and move all the pushes to the beginning of the function
with corresponding pops at the end.
We do this to prepare fixes.
Tested-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180110192556.6026.74187.stgit@tlendack-t1.amdoffice.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
If a nonexistent file is supplied to objtool, it complains with a
non-helpful error:
open: No such file or directory
Improve it to:
objtool: Can't open 'foo': No such file or directory
Reported-by: Markus <M4rkusXXL@web.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/406a3d00a21225eee2819844048e17f68523ccf6.1516025651.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
