| Age | Commit message (Collapse) | Author |
|---|
|
This commit fixes a misunderstanding in commit 4a3e0aeddf09 ("net: dsa:
mv88e6xxx: don't use PHY_DETECT on internal PHY's").
For Marvell DSA switches with the PHY_DETECT bit (for non-6250 family
devices), controls whether the PPU polls the PHY to retrieve the link,
speed, duplex and pause status to update the port configuration. This
applies for both internal and external PHYs.
For some switches such as 88E6352 and 88E6390X, PHY_DETECT has an
additional function of enabling auto-media mode between the internal
PHY and SERDES blocks depending on which first gains link.
The original intention of commit 5d5b231da7ac (net: dsa: mv88e6xxx: use
PHY_DETECT in mac_link_up/mac_link_down) was to allow this bit to be
used to detect when this propagation is enabled, and allow software to
update the port configuration. This has found to be necessary for some
switches which do not automatically propagate status from the SERDES to
the port, which includes the 88E6390. However, commit 4a3e0aeddf09
("net: dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's") breaks
this assumption.
Maarten Zanders has confirmed that the issue he was addressing was for
an 88E6250 switch, which does not have a PHY_DETECT bit in bit 12, but
instead a link status bit. Therefore, mv88e6xxx_port_ppu_updates() does
not report correctly.
This patch resolves the above issues by reverting Maarten's change and
instead making mv88e6xxx_port_ppu_updates() indicate whether the port
is internal for the 88E6250 family of switches.
Yes, you're right, I'm targeting the 6250 family. And yes, your
suggestion would solve my case and is a better implementation for
the other devices (as far as I can see).
Fixes: 4a3e0aeddf09 ("net: dsa: mv88e6xxx: don't use PHY_DETECT on internal PHY's")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Maarten Zanders <maarten.zanders@mind.be>
Link: https://lore.kernel.org/r/E1muXm7-00EwJB-7n@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Vladimir Oltean says:
====================
Rework DSA bridge TX forwarding offload API
This change set is preparation work for DSA support of bridge FDB
isolation. It replaces struct net_device *dp->bridge_dev with a struct
dsa_bridge *dp->bridge that contains some extra information about that
bridge, like a unique number kept by DSA.
Up until now we computed that number only with the bridge TX forwarding
offload feature, but it will be needed for other features too, like for
isolation of FDB entries belonging to different bridges. Hardware
implementations vary, but one common pattern seems to be the presence of
a FID field which can be associated with that bridge number kept by DSA.
The idea was outlined here:
https://patchwork.kernel.org/project/netdevbpf/patch/20210818120150.892647-16-vladimir.oltean@nxp.com/
(the difference being that with this new proposal, drivers would not
need to call dsa_bridge_num_find, instead the bridge_num would be part
of the struct dsa_bridge :: num passed as argument).
No functional change is intended for drivers that don't already make use
of the bridge TX forwarding offload. I've tested the changes on the
felix, sja1105 and mv88e6xxx drivers, but nonetheless I'm copying all
DSA driver maintainers due to API changes that are taking place.
Compared to v1 and v2, the amount of patches is larger, but the contents
is mostly the same, just split up hopefully a bit better for review.
====================
Link: https://lore.kernel.org/r/20211206165758.1553882-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We don't really need new switch API for these, and with new switches
which intend to add support for this feature, it will become cumbersome
to maintain.
The change consists in restructuring the two drivers that implement this
offload (sja1105 and mv88e6xxx) such that the offload is enabled and
disabled from the ->port_bridge_{join,leave} methods instead of the old
->port_bridge_tx_fwd_{,un}offload.
The only non-trivial change is that mv88e6xxx_map_virtual_bridge_to_pvt()
has been moved to avoid a forward declaration, and the
mv88e6xxx_reg_lock() calls from inside it have been removed, since
locking is now done from mv88e6xxx_port_bridge_{join,leave}.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is a preparation patch for the removal of the DSA switch methods
->port_bridge_tx_fwd_offload() and ->port_bridge_tx_fwd_unoffload().
The plan is for the switch to report whether it offloads TX forwarding
directly as a response to the ->port_bridge_join() method.
This change deals with the noisy portion of converting all existing
function prototypes to take this new boolean pointer argument.
The bool is placed in the cross-chip notifier structure for bridge join,
and a reference to it is provided to drivers. In the next change, DSA
will then actually look at this value instead of calling
->port_bridge_tx_fwd_offload().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The main desire behind this is to provide coherent bridge information to
the fast path without locking.
For example, right now we set dp->bridge_dev and dp->bridge_num from
separate code paths, it is theoretically possible for a packet
transmission to read these two port properties consecutively and find a
bridge number which does not correspond with the bridge device.
Another desire is to start passing more complex bridge information to
dsa_switch_ops functions. For example, with FDB isolation, it is
expected that drivers will need to be passed the bridge which requested
an FDB/MDB entry to be offloaded, and along with that bridge_dev, the
associated bridge_num should be passed too, in case the driver might
want to implement an isolation scheme based on that number.
We already pass the {bridge_dev, bridge_num} pair to the TX forwarding
offload switch API, however we'd like to remove that and squash it into
the basic bridge join/leave API. So that means we need to pass this
pair to the bridge join/leave API.
During dsa_port_bridge_leave, first we unset dp->bridge_dev, then we
call the driver's .port_bridge_leave with what used to be our
dp->bridge_dev, but provided as an argument.
When bridge_dev and bridge_num get folded into a single structure, we
need to preserve this behavior in dsa_port_bridge_leave: we need a copy
of what used to be in dp->bridge.
Switch drivers check bridge membership by comparing dp->bridge_dev with
the provided bridge_dev, but now, if we provide the struct dsa_bridge as
a pointer, they cannot keep comparing dp->bridge to the provided
pointer, since this only points to an on-stack copy. To make this
obvious and prevent driver writers from forgetting and doing stupid
things, in this new API, the struct dsa_bridge is provided as a full
structure (not very large, contains an int and a pointer) instead of a
pointer. An explicit comparison function needs to be used to determine
bridge membership: dsa_port_offloads_bridge().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the static inline helpers from net/dsa/dsa_priv.h to
include/net/dsa.h, so that drivers can call functions such as
dsa_port_offloads_bridge_dev(), which will be necessary after the
transition to a more complex bridge structure.
More functions than are needed right now are being moved, but this is
done for uniformity.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the majority of dsa_port_bridge_dev_get() calls in drivers is
just to check whether a port is under the bridge device provided as
argument by the DSA API.
We'd like to change that DSA API so that a more complex structure is
provided as argument. To keep things more generic, and considering that
the new complex structure will be provided by value and not by
reference, direct comparisons between dp->bridge and the provided bridge
will be broken. The generic way to do the checking would simply be to
do something like dsa_port_offloads_bridge(dp, &bridge).
But there's a problem, we already have a function named that way, which
actually takes a bridge_dev net_device as argument. Rename it so that we
can use dsa_port_offloads_bridge for something else.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The location of the bridge device pointer and number is going to change.
It is not going to be kept individually per port, but in a common
structure allocated dynamically and which will have lockdep validation.
Use the helpers to access these elements so that we have a migration
path to the new organization.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The location of the bridge device pointer and number is going to change.
It is not going to be kept individually per port, but in a common
structure allocated dynamically and which will have lockdep validation.
Create helpers to access these elements so that we have a migration path
to the new organization.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
comparison
The goal of this change is to reduce mv88e6xxx_port_vlan() to a form
where dsa_port_bridge_same() can be used, since the dp->bridge_dev
pointer will be hidden in a future change.
To do that, we observe that the "br" pointer is deduced from a
dp->bridge_dev in both cases (of a physical switch port as well as a
virtual bridge). So instead of keeping the "br" pointer, we can just
keep the "dp" pointer from which "br" gets derived.
In the last iteration over switch ports, we must use another iterator
variable, "other_dp"since now we use the "dp" variable to keep an
indirect reference to the bridge. While at it, the old code used to
filter only the ports which were part of the same switch as "ds".
There exists a dedicated DSA port iterator for that:
dsa_switch_for_each_port (which skips the ports in the tree that belong
to non-local switches), so we can just use that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
mv88e6xxx_port_check_hw_vlan
Avoid a plethora of dsa_to_port() calls (some hidden behind
dsa_is_*_port and some in plain sight) by keeping two struct dsa_port
references: one to the port passed as argument, and another to the other
ports of the switch that we're iterating over.
This isn't called from the DSA initialization path, so there is no risk
that we have user ports without a dp->slave populated. So the combined
checks that a port isn't a DSA port, a CPU port, or doesn't have a slave
net device (therefore is unused), are strictly equivalent to the simple
check that the port is a user port. This is already handled by the DSA
iterator.
i gets replaced by other_dp->index, dsa_is_*_port calls get replaced by
dsa_port_is_*, and dsa_to_port gets replaced by the respective pointer
directly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Avoid repeated calls to dsa_to_port() (some hidden behind dsa_is_user_port
and some in plain sight) by keeping two struct dsa_port references: one
to the port passed as argument, and another to the other ports of the
switch that we're iterating over.
dsa_to_port(ds, i) gets replaced by other_dp, i gets replaced by
other_port which is derived from other_dp->index, dsa_is_user_port is
handled by the DSA iterator.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The service where DSA assigns a unique bridge number for each forwarding
domain is useful even for drivers which do not implement the TX
forwarding offload feature.
For example, drivers might use the dp->bridge_num for FDB isolation.
So rename ds->num_fwd_offloading_bridges to ds->max_num_bridges, and
calculate a unique bridge_num for all drivers that set this value.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
I have seen too many bugs already due to the fact that we must encode an
invalid dp->bridge_num as a negative value, because the natural tendency
is to check that invalid value using (!dp->bridge_num). Latest example
can be seen in commit 1bec0f05062c ("net: dsa: fix bridge_num not
getting cleared after ports leaving the bridge").
Convert the existing users to assume that dp->bridge_num == 0 is the
encoding for invalid, and valid bridge numbers start from 1.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 53182e81f47d4ea0c727c49ad23cb782173ab849.
This added tool dependencies on various build systems using %.dtb
targets. Validation will need to be controlled by a kconfig or make
variable instead, but for now let's just revert it.
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
For x86 hybrid CPUs like Alder Lake, the order of CPU selection should
be based strictly on CPU priority. Don't include cluster topology for
hybrid CPUs to avoid interference with such CPU selection order.
On Alder Lake, the Atom CPU cluster has more capacity (4 Atom CPUs) vs
Big core cluster (2 hyperthread CPUs). This could potentially bias CPU
selection towards Atom over Big Core, when Big core CPU has higher
priority.
Fixes: 66558b730f25 ("sched: Add cluster scheduler level for x86")
Suggested-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Tim Chen <tim.c.chen@linux.intel.com>
Tested-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Link: https://lkml.kernel.org/r/20211204091402.GM16608@worktop.programming.kicks-ass.net
|
|
virtio device id value can be more than 31. Hence, use BIT_ULL in
assignment.
Fixes: 33b347503f01 ("vdpa: Define vdpa mgmt device, ops and a netlink interface")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Parav Pandit <parav@nvidia.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20211130042949.88958-1-parav@nvidia.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The VMADDR_CID_ANY flag used by a socket means that the socket isn't bound
to any specific CID. For example, a host vsock server may want to be bound
with VMADDR_CID_ANY, so that a guest vsock client can connect to the host
server with CID=VMADDR_CID_HOST (i.e. 2), and meanwhile, a host vsock
client can connect to the same local server with CID=VMADDR_CID_LOCAL
(i.e. 1).
The current implementation sets the destination socket's svm_cid to a
fixed CID value after the first client's connection, which isn't an
expected operation. For example, if the guest client first connects to the
host server, the server's svm_cid gets set to VMADDR_CID_HOST, then other
host clients won't be able to connect to the server anymore.
Reproduce steps:
1. Run the host server:
socat VSOCK-LISTEN:1234,fork -
2. Run a guest client to connect to the host server:
socat - VSOCK-CONNECT:2:1234
3. Run a host client to connect to the host server:
socat - VSOCK-CONNECT:1:1234
Without this patch, step 3. above fails to connect, and socat complains
"socat[1720] E connect(5, AF=40 cid:1 port:1234, 16): Connection
reset by peer".
With this patch, the above works well.
Fixes: c0cfa2d8a788 ("vsock: add multi-transports support")
Signed-off-by: Wei Wang <wei.w.wang@intel.com>
Link: https://lore.kernel.org/r/20211126011823.1760-1-wei.w.wang@intel.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
|
|
virtio_max_dma_size() returns the maximum DMA mapping size of the virtio
device by querying dma_max_mapping_size() for the device when the DMA
API is in use for the vring. Unfortunately, the device passed is
initialised by register_virtio_device() and does not inherit the DMA
configuration from its parent, resulting in SWIOTLB errors when bouncing
is enabled and the default 256K mapping limit (IO_TLB_SEGSIZE) is not
respected:
| virtio-pci 0000:00:01.0: swiotlb buffer is full (sz: 294912 bytes), total 1024 (slots), used 725 (slots)
Follow the pattern used elsewhere in the virtio_ring code when calling
into the DMA layer and pass the parent device to dma_max_mapping_size()
instead.
Cc: Marc Zyngier <maz@kernel.org>
Cc: Quentin Perret <qperret@google.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20211201112018.25276-1-will@kernel.org
Acked-by: Jason Wang <jasowang@redhat.com>
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Fixes: e6d6dd6c875e ("virtio: Introduce virtio_max_dma_size()")
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
bpf_create_map is deprecated. Replace it with bpf_map_create. Also add a
__weak bpf_map_create() so that when older version of libbpf is linked as
a shared library, it falls back to bpf_create_map().
Fixes: 992c4225419a ("libbpf: Unify low-level map creation APIs w/ new bpf_map_create()")
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211207232340.2561471-1-song@kernel.org
|
|
When neither VIRTIO_PCI_LIB nor VIRTIO are enabled, but the alibaba
vdpa driver is, the kernel runs into a link error because the legacy
virtio module never gets built:
x86_64-linux-ld: drivers/vdpa/alibaba/eni_vdpa.o: in function `eni_vdpa_set_features':
eni_vdpa.c:(.text+0x23f): undefined reference to `vp_legacy_set_features'
x86_64-linux-ld: drivers/vdpa/alibaba/eni_vdpa.o: in function `eni_vdpa_set_vq_state':
eni_vdpa.c:(.text+0x2fe): undefined reference to `vp_legacy_get_queue_enable'
x86_64-linux-ld: drivers/vdpa/alibaba/eni_vdpa.o: in function `eni_vdpa_set_vq_address':
eni_vdpa.c:(.text+0x376): undefined reference to `vp_legacy_set_queue_address'
x86_64-linux-ld: drivers/vdpa/alibaba/eni_vdpa.o: in function `eni_vdpa_set_vq_ready':
eni_vdpa.c:(.text+0x3b4): undefined reference to `vp_legacy_set_queue_address'
x86_64-linux-ld: drivers/vdpa/alibaba/eni_vdpa.o: in function `eni_vdpa_free_irq':
eni_vdpa.c:(.text+0x460): undefined reference to `vp_legacy_queue_vector'
x86_64-linux-ld: eni_vdpa.c:(.text+0x4b7): undefined reference to `vp_legacy_config_vector'
x86_64-linux-ld: drivers/vdpa/alibaba/eni_vdpa.o: in function `eni_vdpa_reset':
When VIRTIO_PCI_LIB was added, it was correctly added to drivers/Makefile
as well, but for the legacy module, this is missing. Solve this by always
entering drivers/virtio during the build and letting its Makefile take
care of the individual options, rather than having a separate line for
each sub-option.
Fixes: 64b9f64f80a6 ("vdpa: introduce virtio pci driver")
Fixes: e85087beedca ("eni_vdpa: add vDPA driver for Alibaba ENI")
Fixes: d89c8169bd70 ("virtio-pci: introduce legacy device module")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20211206085034.2836099-1-arnd@kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This condition checks "len" but it does not check "offset" and that
could result in an out of bounds read if "offset > dev->config_size".
The problem is that since both variables are unsigned the
"dev->config_size - offset" subtraction would result in a very high
unsigned value.
I think these checks might not be necessary because "len" and "offset"
are supposed to already have been validated using the
vhost_vdpa_config_validate() function. But I do not know the code
perfectly, and I like to be safe.
Fixes: c8a6153b6c59 ("vduse: Introduce VDUSE - vDPA Device in Userspace")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211208150956.GA29160@kili
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Cc: stable@vger.kernel.org
|
|
In this function "c->off" is a u32 and "size" is a long. On 64bit systems
if "c->off" is greater than "size" then "size - c->off" is a negative and
we always return -E2BIG. But on 32bit systems the subtraction is type
promoted to a high positive u32 value and basically any "c->len" is
accepted.
Fixes: 4c8cf31885f6 ("vhost: introduce vDPA-based backend")
Reported-by: Xie Yongji <xieyongji@bytedance.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211208103337.GA4047@kili
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Cc: stable@vger.kernel.org
|
|
The "config.offset" comes from the user. There needs to a check to
prevent it being out of bounds. The "config.offset" and
"dev->config_size" variables are both type u32. So if the offset if
out of bounds then the "dev->config_size - config.offset" subtraction
results in a very high u32 value. The out of bounds offset can result
in memory corruption.
Fixes: c8a6153b6c59 ("vduse: Introduce VDUSE - vDPA Device in Userspace")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211208103307.GA3778@kili
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Cc: stable@vger.kernel.org
|
|
The earlier __packed annotations added in commit d71038c05970 ("libertas:
Fix alignment issues in libertas core") were not duplicated when
libertas_af was added in commit 7670e62c7ed6 ("libertas_tf: header file"),
even though they share several structure definitions. Add the missing
annotations which commit 642a57475b30 ("libertas_tf: Use struct_group()
for memcpy() region") exposed. Quoting the prior libertas fix: "Data
structures that come over the wire from the WLAN firmware must be
packed."
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/linux-mm/202111302102.apaePz2J-lkp@intel.com
Fixes: 642a57475b30 ("libertas_tf: Use struct_group() for memcpy() region")
Fixes: 7670e62c7ed6 ("libertas_tf: header file")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211201173234.578124-3-keescook@chromium.org
|
|
Build testing of the newly added struct_group() usage missed smaller
architecture width tests for changes to pahole output. Add the missed
__packed annotation with struct_group() usage in a __packed struct.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/linux-mm/202111302102.apaePz2J-lkp@intel.com
Fixes: 5fd32ae0433a ("libertas: Use struct_group() for memcpy() region")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211201173234.578124-2-keescook@chromium.org
|
|
Quoting Jia-Ju Bai <baijiaju1990@gmail.com>:
mwifiex_dequeue_tx_packet()
spin_lock_bh(&priv->wmm.ra_list_spinlock); --> Line 1432 (Lock A)
mwifiex_send_addba()
spin_lock_bh(&priv->sta_list_spinlock); --> Line 608 (Lock B)
mwifiex_process_sta_tx_pause()
spin_lock_bh(&priv->sta_list_spinlock); --> Line 398 (Lock B)
mwifiex_update_ralist_tx_pause()
spin_lock_bh(&priv->wmm.ra_list_spinlock); --> Line 941 (Lock A)
Similar report for mwifiex_process_uap_tx_pause().
While the locking expectations in this driver are a bit unclear, the
Fixed commit only intended to protect the sta_ptr, so we can drop the
lock as soon as we're done with it.
IIUC, this deadlock cannot actually happen, because command event
processing (which calls mwifiex_process_sta_tx_pause()) is
sequentialized with TX packet processing (e.g.,
mwifiex_dequeue_tx_packet()) via the main loop (mwifiex_main_process()).
But it's good not to leave this potential issue lurking.
Fixes: f0f7c2275fb9 ("mwifiex: minor cleanups w/ sta_list_spinlock in cfg80211.c")
Cc: Douglas Anderson <dianders@chromium.org>
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Link: https://lore.kernel.org/linux-wireless/0e495b14-efbb-e0da-37bd-af6bd677ee2c@gmail.com/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/YaV0pllJ5p/EuUat@google.com
|
|
The driver was zeroing live stats that could be fetched by
ndo_get_stats64 at any time. This could result in inconsistent
statistics, and the telltale sign was when reading stats frequently from
/proc/net/dev, the stats would go backwards.
Fix by collecting stats into a local, and delaying when we write to the
structure so it's not incremental.
Fixes: fcea6f3da546 ("ice: Add stats and ethtool support")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This eliminates warning message:
SPI driver WILC_SPI has no spi_device_id for microchip,wilc1000
and makes device-tree autoloading work.
Signed-off-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211202045001.2901903-1-davidm@egauge.net
|
|
This is found by Smatch static checker warning:
drivers/net/wireless/realtek/rtw89/mac80211.c:31 rtw89_ops_tx()
error: uninitialized symbol 'qsel'.
The warning is because 'qsel' isn't filled by rtw89_core_tx_write() due to
failed to write. The way to fix it is to avoid kicking off TX DMA, so add
'return' to the failure case.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211201093816.13806-1-pkshih@realtek.com
|
|
Originally, cch_by_bw recorded center channels of each available
bandwidths under current bandwidth. And the plan was to iterate
cch_by_bw as parameters to query other configurations. However,
we have not used it for the time being. Keeping it will disturb
the follow-up things, such as bandwidth 160 MHz, so we remove it
for now. If it's really needed at some point, we will redesign it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211201080901.12125-1-pkshih@realtek.com
|
|
With wrong rtwsta->mac_id, it can't send out ack properly when we receive
assoc response occasionally. Then, it failed to connect an AP.
The cause is that we store 'sta' and use it somewhere. To correct this,
remove the variable and use mac_id in drv_priv of 'sta' or 'vif' passed
by mac80211.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211201080607.11211-1-pkshih@realtek.com
|
|
Show channel and bandwidth in debugfs tx_pwr_tbl to make it easier
to understand which tx power table is shown currently, and to reduce
additional checks through other ways.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211129020626.6384-1-pkshih@realtek.com
|
|
It is useful to fix the bit rate of TX packets. For example, if
someone is measuring the TX power, or debugging with the issues
of the TX throughput on the field.
To set the value of fixed rate, one should input corresponding
desc rate index (ex, 0x0b for DESC_RATE54M to fix at 54 Mbps).
Set a value larger than DESC_RATE_MAX will disable fix rate, so
the rate adaptive mechanism can resume to work.
Example,
To fix rate at MCS 1:
echo 0x0d > /sys/kernel/debug/ieee80211/phy0/rtw88/fix_rate
To not to fix rate:
echo 0xff > /sys/kernel/debug/ieee80211/phy0/rtw88/fix_rate
To know which rate was fixed at:
cat /sys/kernel/debug/ieee80211/phy0/rtw88/fix_rate
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211129020506.6273-1-pkshih@realtek.com
|
|
We used to fill in rx skbs' frequency field by mac80211's current
channel value. In some cases, mac80211 switches channel before all
rx packets have been processed. This results in incorrect bss info.
We fix this by filling in frequency field with channel index obtained
from hardware, then fix potential cck missing issue by skb's original
hw rate. After all fix is done, convert hw rate back to the supported
band rate index.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211111023706.14154-3-pkshih@realtek.com
|
|
Update scan_mac_addr to address CAM as A1, so hardware can ACK probe
response properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211111023706.14154-2-pkshih@realtek.com
|
|
In order to use compiler to check if we do improper cast of const* on
arguments of inline function.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211119054512.10620-4-pkshih@realtek.com
|
|
Add 'const' to be clear that this is a read-only access, and this patch
doesn't change logic at all.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211119054512.10620-3-pkshih@realtek.com
|
|
After mt7921s got added, there are two possible build problems:
a) mt7921s does not get built at all if mt7921e is not also enabled
b) there is a link error when mt7921e is a loadable module, but mt7921s
configured as built-in:
ERROR: modpost: "mt7921_mac_sta_add" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
ERROR: modpost: "mt7921_mac_sta_assoc" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
ERROR: modpost: "mt7921_mac_sta_remove" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
ERROR: modpost: "mt7921_mac_write_txwi" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
ERROR: modpost: "mt7921_mcu_drv_pmctrl" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
ERROR: modpost: "mt7921_mcu_fill_message" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
ERROR: modpost: "mt7921_mcu_parse_response" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
ERROR: modpost: "mt7921_ops" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
ERROR: modpost: "mt7921_queue_rx_skb" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
ERROR: modpost: "mt7921_update_channel" [drivers/net/wireless/mediatek/mt76/mt7921/mt7921e.ko] undefined!
Fix both by making sure that Kbuild enters the subdirectory when
either one is enabled.
Fixes: 48fab5bbef40 ("mt76: mt7921: introduce mt7921s support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211204173848.873293-3-arnd@kernel.org
|
|
This is now the only driver that selects the LEDS_CLASS framework,
which is normally user-selectable. While it doesn't strictly cause
a bug, rework the Kconfig logic to be more consistent with what
other drivers do, and only enable LED support in brcmsmac if the
dependencies are all there, rather than using 'select' to enable
what it needs.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211204173848.873293-2-arnd@kernel.org
|
|
The dependencies for LED configuration are highly inconsistent and too
complicated at the moment. One of the results is a randconfig failure I
get very rarely when LEDS_CLASS is in a loadable module, but the wireless
core is built-in:
WARNING: unmet direct dependencies detected for MAC80211_LEDS
Depends on [n]: NET [=y] && WIRELESS [=y] && MAC80211 [=y] && (LEDS_CLASS [=m]=y || LEDS_CLASS [=m]=MAC80211 [=y])
Selected by [m]:
- IWLEGACY [=m] && NETDEVICES [=y] && WLAN [=y] && WLAN_VENDOR_INTEL [=y]
- IWLWIFI_LEDS [=y] && NETDEVICES [=y] && WLAN [=y] && WLAN_VENDOR_INTEL [=y] && IWLWIFI [=m] && (LEDS_CLASS [=m]=y || LEDS_CLASS [=m]=IWLWIFI [=m]) && (IWLMVM [=m] || IWLDVM [=m])
aarch64-linux-ld: drivers/net/wireless/ath/ath5k/led.o: in function `ath5k_register_led':
led.c:(.text+0x60): undefined reference to `led_classdev_register_ext'
aarch64-linux-ld: drivers/net/wireless/ath/ath5k/led.o: in function `ath5k_unregister_leds':
led.c:(.text+0x200): undefined reference to `led_classdev_unregister'
For iwlwifi, the dependency is wrong, since this config prevents the
MAC80211_LEDS code from being part of a built-in MAC80211 driver.
For iwlegacy, this is worse because the driver tries to force-enable
the other subsystems, which is both a layering violation and a bug
because it will still fail with MAC80211=y and IWLEGACY=m, leading
to LEDS_CLASS being a module as well.
The actual link failure in the ath5k driver is a result of MAC80211_LEDS
being enabled but not usable. With the Kconfig logic fixed in the
Intel drivers, the ath5k driver works as expected again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211204173848.873293-1-arnd@kernel.org
|
|
If we get to the WARN_ONCE(..., "Got a HT rate (...)", ...)
here with a NULL sta, then we crash because mvmsta is bad
and we try to dereference it. Fix that by printing -1 as the
state if no station was given.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 6761a718263a ("iwlwifi: mvm: add explicit check for non-data frames in get Tx rate")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/iwlwifi.20211203140410.1a1541d7dcb5.I606c746e11447fe168cf046376b70b04e278c3b4@changeid
|
|
Originally "out_fence" was set using out_fence = sync_file_create() but
which returns NULL, but now it is set with out_fence = eb_requests_create()
which returns error pointers. The error path needs to be modified to
avoid an Oops in the "goto err_request;" path.
Fixes: 544460c33821 ("drm/i915: Multi-BB execbuf")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211202044831.29583-1-matthew.brost@intel.com
(cherry picked from commit 8722ded49ce8a0c706b373e8087eb810684962ff)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Battery status is reported for the Asus UX550VE touchscreen even though
it does not have a battery. Prevent it from always reporting the
battery as low.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1897823
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Adding ops cleanup to unregister_ftrace_direct_multi,
so it can be reused in another register call.
Link: https://lkml.kernel.org/r/20211206182032.87248-3-jolsa@kernel.org
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Fixes: f64dd4627ec6 ("ftrace: Add multi direct register/unregister interface")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
Now when we have *direct_multi interface the direct_functions
hash is no longer owned just by direct_ops. It's also used by
any other ftrace_ops passed to *direct_multi interface.
Thus to find out that we are unregistering the last function
from direct_ops, we need to check directly direct_ops's hash.
Link: https://lkml.kernel.org/r/20211206182032.87248-2-jolsa@kernel.org
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Fixes: f64dd4627ec6 ("ftrace: Add multi direct register/unregister interface")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
dma_fence_chain_find_seqno only ever returns the top fence in the
chain or an unsignalled fence. Hence if we request a seqno that
is already signalled it returns a NULL fence. Some callers are
not prepared to handle this, like the syncobj transfer functions
for example.
This behavior is "new" with timeline syncobj and it looks like
not all callers were updated. To fix this behavior make sure
that a successful drm_sync_find_fence always returns a non-NULL
fence.
v2: Move the fix to drm_syncobj_find_fence from the transfer
functions.
Fixes: ea569910cbab ("drm/syncobj: add transition iotcls between binary and timeline v2")
Cc: stable@vger.kernel.org
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211208023935.17018-1-bas@basnieuwenhuizen.nl
|
|
nvmet_tcp_handle_req_failure needs to understand weather to prepare
for incoming data or the next pdu. However if we misidentify this, we
will wait for 0-length data, and queue the response although nvmet_req_init
already did that.
The particular command was namespace management command with no data,
which was incorrectly categorized as a command with incapsule data.
Also, add a code comment of what we are trying to do here.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
I hit the BUG_ON() with generic/475 test case, and to my surprise, all
callers of btrfs_del_root_ref() are already aborting transaction, thus
there is not need for such BUG_ON(), just go to @out label and caller
will properly handle the error.
CC: stable@vger.kernel.org # 5.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
When finishing a zone that is used by a dedicated data relocation
block group, also remove its reference from fs_info, so we're not trying
to use a full block group for allocations during data relocation, which
will always fail.
The result is we're not making any forward progress and end up in a
deadlock situation.
Fixes: c2707a255623 ("btrfs: zoned: add a dedicated data relocation block group")
Reviewed-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
