| Age | Commit message (Collapse) | Author |
|---|
|
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In mcba_usb, we have observed that when you unplug the device, the driver will
endlessly resubmit failing URBs, which can cause CPU stalls. This issue
is fixed in mcba_usb by catching the codes seen on device disconnect
(-EPIPE and -EPROTO).
This driver also resubmits in the case of -EPIPE and -EPROTO, so fix it
in the same way.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When we unplug the device, we can see both -EPIPE and -EPROTO depending
on exact timing and what system we run on. If we continue to resubmit
URBs, they will immediately fail, and they can cause stalls, especially
on slower CPUs.
Fix this by not resubmitting on -EPROTO, as we already do on -EPIPE.
Signed-off-by: Martin Kelly <mkelly@xevo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
A regression fix introduced a harmless type mismatch warning:
drivers/scsi/bfa/bfad_bsg.c: In function 'bfad_im_bsg_vendor_request':
drivers/scsi/bfa/bfad_bsg.c:3137:35: error: initialization of 'struct bfad_im_port_s *' from 'long unsigned int' makes pointer from integer without a cast [-Werror=int-conversion]
struct bfad_im_port_s *im_port = shost->hostdata[0];
^~~~~
drivers/scsi/bfa/bfad_bsg.c: In function 'bfad_im_bsg_els_ct_request':
drivers/scsi/bfa/bfad_bsg.c:3353:35: error: initialization of 'struct bfad_im_port_s *' from 'long unsigned int' makes pointer from integer without a cast [-Werror=int-conversion]
struct bfad_im_port_s *im_port = shost->hostdata[0];
This changes the code back to shost_priv() once more, but encapsulates
it in an inline function to document the rather unusual way of
using the private data only as a pointer to the previously allocated
structure.
I did not try to get rid of the extra indirection level entirely,
which would have been rather invasive and required reworking the entire
initialization sequence.
Fixes: 45349821ab3a ("scsi: bfa: fix access to bfad_im_port_s")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Before commit 0df21c86bdbf ("scsi: implement .get_budget and .put_budget
for blk-mq"), we run queue after 3ms if queue is idle and SCSI device
queue isn't ready, which is done in handling BLK_STS_RESOURCE. After
commit 0df21c86bdbf is introduced, queue won't be run any more under
this situation.
IO hang is observed when timeout happened, and this patch fixes the IO
hang issue by running queue after delay in scsi_dev_queue_ready, just
like non-mq. This issue can be triggered by the following script[1].
There is another issue which can be covered by running idle queue: when
.get_budget() is called on request coming from hctx->dispatch_list, if
one request just completes during .get_budget(), we can't depend on
SCSI's restart to make progress any more. This patch fixes the race too.
With this patch, we basically recover to previous behaviour (before
commit 0df21c86bdbf) of handling idle queue when running out of
resource.
[1] script for test/verify SCSI timeout
rmmod scsi_debug
modprobe scsi_debug max_queue=1
DEVICE=`ls -d /sys/bus/pseudo/drivers/scsi_debug/adapter*/host*/target*/*/block/* | head -1 | xargs basename`
DISK_DIR=`ls -d /sys/block/$DEVICE/device/scsi_disk/*`
echo "using scsi device $DEVICE"
echo "-1" >/sys/bus/pseudo/drivers/scsi_debug/every_nth
echo "temporary write through" >$DISK_DIR/cache_type
echo "128" >/sys/bus/pseudo/drivers/scsi_debug/opts
echo none > /sys/block/$DEVICE/queue/scheduler
dd if=/dev/$DEVICE of=/dev/null bs=1M iflag=direct count=1 &
sleep 5
echo "0" >/sys/bus/pseudo/drivers/scsi_debug/opts
wait
echo "SUCCESS"
Fixes: 0df21c86bdbf ("scsi: implement .get_budget and .put_budget for blk-mq")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The added check produces a build error when CONFIG_PROC_FS is
disabled:
net/ipv4/netfilter/ipt_CLUSTERIP.c: In function 'clusterip_net_exit':
net/ipv4/netfilter/ipt_CLUSTERIP.c:822:28: error: 'cn' undeclared (first use in this function)
This moves the variable declaration out of the #ifdef to make it
available to the WARN_ON_ONCE().
Fixes: 613d0776d3fe ("netfilter: exit_net cleanup check added")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
regression fix for vc4 + rpm stable fix for analogix bridge
* tag 'drm-misc-fixes-2017-12-07' of git://anongit.freedesktop.org/drm/drm-misc:
drm/bridge: analogix dp: Fix runtime PM state in get_modes() callback
drm/vc4: Fix false positive WARN() backtrace on refcount_inc() usage
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix for fd.o bug #103997 CNL eDP + HDMI causing a machine hard hang (James)
- Fix to allow suspending with a wedged GPU to hopefully unwedge it (Chris)
- Fix for Gen2 vblank timestap/frame counter jumps (Ville)
- Revert of a W/A for enabling FBC on CNL/GLK for certain images
and sizes (Rodrigo)
- Lockdep fix for i915 userptr code (Chris)
gvt-fixes-2017-12-06
- Fix invalid hw reg read value for vGPU (Xiong)
- Fix qemu warning on PCI ROM bar missing (Changbin)
- Workaround preemption regression (Zhenyu)
* tag 'drm-intel-fixes-2017-12-07' of git://anongit.freedesktop.org/drm/drm-intel:
Revert "drm/i915: Display WA #1133 WaFbcSkipSegments:cnl, glk"
drm/i915: Call i915_gem_init_userptr() before taking struct_mutex
drm/i915/gvt: set max priority for gvt context
drm/i915/gvt: Don't mark vgpu context as inactive when preempted
drm/i915/gvt: Limit read hw reg to active vgpu
drm/i915/gvt: Export intel_gvt_render_mmio_to_ring_id()
drm/i915/gvt: Emulate PCI expansion ROM base address register
drm/i915/cnl: Mask previous DDI - PLL mapping
drm/i915: Fix vblank timestamp/frame counter jumps on gen2
drm/i915: Skip switch-to-kernel-context on suspend when wedged
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
- fix page fault issue due to using wrong device object in prime import.
- drop NONCONTIG flag without IOMMU support.
- remove unnecessary members and declaration.
* tag 'exynos-drm-fixes-for-v4.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: remove unnecessary function declaration
drm/exynos: remove unnecessary descrptions
drm/exynos: gem: Drop NONCONTIG flag for buffers allocated without IOMMU
drm/exynos: Fix dma-buf import
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2017-12-06
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fixing broken uapi for BPF tracing programs for s390 and arm64
architectures due to pt_regs being in-kernel only, and not part
of uapi right now. A wrapper is added that exports pt_regs in
an asm-generic way. For arm64 this maps to existing user_pt_regs
structure and for s390 a user_pt_regs structure exporting the
beginning of pt_regs is added and uapi-exported, thus fixing the
BPF issues seen in perf (and BPF selftests), all from Hendrik.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In __flush_qp(), the CQ ARMED bit was being cleared regardless of
whether any notification is actually needed. This resulted in the iser
termination logic getting stuck in ib_drain_sq() because the CQ was not
marked ARMED and thus the drain CQE notification wasn't triggered.
This new bug was exposed when this commit was merged:
commit cbb40fadd31c ("iw_cxgb4: only call the cq comp_handler when the
cq is armed")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The RDMA netlink core code checks validity of messages by ensuring
that type and operand are in range. It works well for almost all
clients except NLDEV, which has cb_table less than number of operands.
Request to access such operand will trigger the following kernel panic.
This patch updates all places where cb_table is declared for the
consistency, but only NLDEV is actually need it.
general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN
Modules linked in:
CPU: 0 PID: 522 Comm: syz-executor6 Not tainted 4.13.0+ #4
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014
task: ffff8800657799c0 task.stack: ffff8800695d000
RIP: 0010:rdma_nl_rcv_msg+0x13a/0x4c0
RSP: 0018:ffff8800695d7838 EFLAGS: 00010207
RAX: dffffc0000000000 RBX: 1ffff1000d2baf0b RCX: 00000000704ff4d7
RDX: 0000000000000000 RSI: ffffffff81ddb03c RDI: 00000003827fa6bc
RBP: ffff8800695d7900 R08: ffffffff82ec0578 R09: 0000000000000000
R10: ffff8800695d7900 R11: 0000000000000001 R12: 000000000000001c
R13: ffff880069d31e00 R14: 00000000ffffffff R15: ffff880069d357c0
FS: 00007fee6acb8700(0000) GS:ffff88006ca00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000201a9000 CR3: 0000000059766000 CR4: 00000000000006b0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
? rdma_nl_multicast+0x80/0x80
rdma_nl_rcv+0x36b/0x4d0
? ibnl_put_attr+0xc0/0xc0
netlink_unicast+0x4bd/0x6d0
? netlink_sendskb+0x50/0x50
? drop_futex_key_refs.isra.4+0x68/0xb0
netlink_sendmsg+0x9ab/0xbd0
? nlmsg_notify+0x140/0x140
? wake_up_q+0xa1/0xf0
? drop_futex_key_refs.isra.4+0x68/0xb0
sock_sendmsg+0x88/0xd0
sock_write_iter+0x228/0x3c0
? sock_sendmsg+0xd0/0xd0
? do_futex+0x3e5/0xb20
? iov_iter_init+0xaf/0x1d0
__vfs_write+0x46e/0x640
? sched_clock_cpu+0x1b/0x190
? __vfs_read+0x620/0x620
? __fget+0x23a/0x390
? rw_verify_area+0xca/0x290
vfs_write+0x192/0x490
SyS_write+0xde/0x1c0
? SyS_read+0x1c0/0x1c0
? trace_hardirqs_on_thunk+0x1a/0x1c
entry_SYSCALL_64_fastpath+0x18/0xad
RIP: 0033:0x7fee6a74a219
RSP: 002b:00007fee6acb7d58 EFLAGS: 00000212 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000638000 RCX: 00007fee6a74a219
RDX: 0000000000000078 RSI: 0000000020141000 RDI: 0000000000000006
RBP: 0000000000000046 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000212 R12: ffff8800695d7f98
R13: 0000000020141000 R14: 0000000000000006 R15: 00000000ffffffff
Code: d6 48 b8 00 00 00 00 00 fc ff df 66 41 81 e4 ff 03 44 8d 72 ff 4a 8d 3c b5 c0 a6 7f 82 44 89 b5 4c ff ff ff 48 89 f9 48 c1 e9 03 <0f> b6 0c 01 48 89 f8 83 e0 07 83 c0 03 38 c8 7c 08 84 c9 0f 85
RIP: rdma_nl_rcv_msg+0x13a/0x4c0 RSP: ffff8800695d7838
---[ end trace ba085d123959c8ec ]---
Kernel panic - not syncing: Fatal exception
Cc: syzkaller <syzkaller@googlegroups.com>
Fixes: b4c598a67ea1 ("RDMA/netlink: Implement nldev device dumpit calback")
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Mistakenly the driver didn't allow RSS hash fields combinations which
involve both IPv4 and IPv6 protocols. This bug caused to failures for
user's use cases for RSS.
Consequently, this patch fixes this bug and allows any combination that
the HW can support.
Additionally, the patch fixes the driver to return an error in case the
user provides an unsupported mask for RSS hash fields.
Fixes: 3078f5f1bd8b ("IB/mlx4: Add support for RSS QP")
Signed-off-by: Guy Levi <guyle@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Per the infiniband spec an SMI MAD can have any PKey. Checking the pkey
on SMI MADs is not necessary, and it seems that some older adapters
using the mthca driver don't follow the convention of using the default
PKey, resulting in false denials, or errors querying the PKey cache.
SMI MAD security is still enforced, only agents allowed to manage the
subnet are able to receive or send SMI MADs.
Reported-by: Chris Blake <chrisrblake93@gmail.com>
Cc: <stable@vger.kernel.org> # v4.12
Fixes: 47a2b338fe63 ("IB/core: Enforce security on management datagrams")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The alternate port number is used as an array index in the IB
security implementation, invalid values can result in a kernel panic.
Cc: <stable@vger.kernel.org> # v4.12
Fixes: d291f1a65232 ("IB/core: Enforce PKey security on QPs")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Ursula Braun says:
====================
smc: fixes 2017-12-07
here are some smc-patches. The initial 4 patches are cleanups.
Patch 5 gets rid of ib_post_sends in tasklet context to avoid peer drops due
to out-of-order receivals.
Patch 6 makes sure, the Linux SMC code understands variable sized CLC proposal
messages built according to RFC7609.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to RFC7609 [1] the CLC proposal message contains an area of
unknown length for future growth. Additionally it may contain up to
8 IPv6 prefixes. The current version of the SMC-code does not
understand CLC proposal messages using these variable length fields and,
thus, is incompatible with SMC implementations in other operating
systems.
This patch makes sure, SMC understands incoming CLC proposals
* with arbitrary length values for future growth
* with up to 8 IPv6 prefixes
[1] SMC-R Informational RFC: http://www.rfc-editor.org/info/rfc7609
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Hans Wippel <hwippel@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SMC protocol requires to send a separate consumer cursor update,
if it cannot be piggybacked to updates of the producer cursor.
When receiving a blocked signal from the sender, this update is sent
already in tasklet context. In addition consumer cursor updates are
sent after data receival.
Sending of cursor updates is controlled by sequence numbers.
Assuming receiving stray messages the receiver drops updates with older
sequence numbers than an already received cursor update with a higher
sequence number.
Sending consumer cursor updates in tasklet context may result in
wrong order sends and its corresponding drops at the receiver. Since
it is sufficient to send consumer cursor updates once the data is
received, this patch gets rid of the consumer cursor update in tasklet
context to guarantee in-sequence arrival of cursor updates.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When waiting for data to be received it must be checked if the
peer signals shutdown. The SMC code uses two different checks
for this purpose, even though just one check is sufficient.
This patch removes the superfluous test for SOCK_DONE.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The smc code never checks the sk_write_pending sock field.
Thus there is no need to update it.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let smc_clc_send_decline() return with an error, if the amount
sent is smaller than the length of an smc decline message.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
smc_close_active_abort() is used in smc_close.c only.
Make it static.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The qmi_wwan minidriver support a 'raw-ip' mode where frames are
received without any ethernet header. This causes alignment issues
because the skbs allocated by usbnet are "IP aligned".
Fix by allowing minidrivers to disable the additional alignment
offset. This is implemented using a per-device flag, since the same
minidriver also supports 'ethernet' mode.
Fixes: 32f7adf633b9 ("net: qmi_wwan: support "raw IP" mode")
Reported-and-tested-by: Jay Foster <jay@systech.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When I switched rcv_rtt_est to high resolution timestamps, I forgot
that tp->tcp_mstamp needed to be refreshed in tcp_rcv_space_adjust()
Using an old timestamp leads to autotuning lags.
Fixes: 645f4c6f2ebd ("tcp: switch rcv_rtt_est and rcvq_space to high resolution timestamps")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a configuration option: CONFIG_NET_DSA_LEGACY allowing to compile out
support for the old platform device and Device Tree binding registration.
Support for these configurations is scheduled to be removed in 4.17.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 28033ae4e0f5 ("net: netlink: Update attr validation to require
exact length for some types") requires attributes using types NLA_U* and
NLA_S* to have an exact length. This change is exposing bugs in various
userspace commands that are sending attributes with an invalid length
(e.g., attribute has type NLA_U8 and userspace sends NLA_U32). While
the commands are clearly broken and need to be fixed, users are arguing
that the sudden change in enforcement is breaking older commands on
newer kernels for use cases that otherwise "worked".
Relax the validation to print a warning mesage similar to what is done
for messages containing extra bytes after parsing.
Fixes: 28033ae4e0f5 ("net: netlink: Update attr validation to require exact length for some types")
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 8d79266bc48c ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
introduced new exit point in ipxip6_rcv. however rcu_read_unlock is
missing there. this diff is fixing this
v1->v2:
instead of doing rcu_read_unlock in place, we are going to "drop"
section (to prevent skb leakage)
Fixes: 8d79266bc48c ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
Signed-off-by: Nikita V. Shirokov <tehnerd@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrew Lunn says:
====================
mv88e6xxx error patch fixes
While trying to bring up a new PHY on a board, i exercised the error
paths a bit, and discovered some bugs. The unwind for interrupt
handling deadlocks, and the MDIO code hits a BUG() when a registered
MDIO device is freed without first being unregistered.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MDIO busses need to be unregistered before they are freed,
otherwise BUG() is called. Add a call to the unregister code if the
registration fails, since we can have multiple busses, of which some
may correctly register before one fails. This requires moving the code
around a little.
Fixes: a3c53be55c95 ("net: dsa: mv88e6xxx: Support multiple MDIO busses")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When removing the interrupt handling code, we should mask the
generation of interrupts. The code however unmasked all
interrupts. This can then cause a new interrupt. We then get into a
deadlock where the interrupt thread is waiting to run, and the code
continues, trying to remove the interrupt handler, which means waiting
for the thread to complete. On a UP machine this deadlocks.
Fix so we really mask interrupts in the hardware. The same error is
made in the error path when install the interrupt handling code.
Fixes: 3460a5770ce9 ("net: dsa: mv88e6xxx: Mask g1 interrupts and free interrupt")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If clk_set_rate() fails, we should disable clk before return.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Branislav Radocaj <branislav@radocaj.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add appropriate calls to clk_disable_unprepare() by jumping to out_mdio
in case orion_mdio_probe() returns -EPROBE_DEFER.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 3d604da1e954 ("net: mvmdio: get and enable optional clock")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some dual port NICs, the 2 ports have to be configured with compatible
link speeds. Under some conditions, a port's configured speed may no
longer be supported. The firmware will send a message to the driver
when this happens.
Improve this logic that prints out the warning by only printing it if
we can determine the link speed that is no longer supported. If the
speed is unknown or it is in autoneg mode, skip the warning message.
Reported-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function virtqueue_get_buf_ctx() could return NULL, the return
value 'buf' need to be checked with NULL, not value 'ctx'.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
cleanup all resource allocated by virtio_mmio_probe.
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
|
|
As mentioned at drivers/base/core.c:
/*
* NOTE: _Never_ directly free @dev after calling this function, even
* if it returned an error! Always use put_device() to give up the
* reference initialized in this function instead.
*/
so we don't free vm_dev until vm_dev.dev.release be called.
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
|
|
* fixes:
ARM: omap2: hide omap3_save_secure_ram on non-OMAP3 builds
arm: dts: nspire: Add missing #phy-cells to usb-nop-xceiv
|
|
In configurations without CONFIG_OMAP3 but with secure RAM support,
we now run into a link failure:
arch/arm/mach-omap2/omap-secure.o: In function `omap3_save_secure_ram':
omap-secure.c:(.text+0x130): undefined reference to `save_secure_ram_context'
The omap3_save_secure_ram() function is only called from the OMAP34xx
power management code, so we can simply hide that function in the
appropriate #ifdef.
Fixes: d09220a887f7 ("ARM: OMAP2+: Fix SRAM virt to phys translation for save_secure_ram_context")
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.
Fixes the following warning in nspire dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
get_modes() callback might be called asynchronously from the DRM core and
it is not synchronized with bridge_enable(), which sets proper runtime PM
state of the main DP device. Fix this by calling pm_runtime_get_sync()
before calling drm_get_edid(), which in turn calls drm_dp_i2c_xfer() and
analogix_dp_transfer() to ensure that main DP device is runtime active
when doing any access to its registers.
This fixes the following kernel issue on Samsung Exynos5250 Snow board:
Unhandled fault: imprecise external abort (0x406) at 0x00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: : 406 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 62 Comm: kworker/0:2 Not tainted 4.13.0-rc2-00364-g4a97a3da420b #3357
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events output_poll_execute
task: edc14800 task.stack: edcb2000
PC is at analogix_dp_transfer+0x15c/0x2fc
LR is at analogix_dp_transfer+0x134/0x2fc
pc : [<c0468538>] lr : [<c0468510>] psr: 60000013
sp : edcb3be8 ip : 0000002a fp : 00000001
r10: 00000000 r9 : edcb3cd8 r8 : edcb3c40
r7 : 00000000 r6 : edd3b380 r5 : edd3b010 r4 : 00000064
r3 : 00000000 r2 : f0ad3000 r1 : edcb3c40 r0 : edd3b010
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 4000406a DAC: 00000051
Process kworker/0:2 (pid: 62, stack limit = 0xedcb2210)
Stack: (0xedcb3be8 to 0xedcb4000)
[<c0468538>] (analogix_dp_transfer) from [<c0424ba4>] (drm_dp_i2c_do_msg+0x8c/0x2b4)
[<c0424ba4>] (drm_dp_i2c_do_msg) from [<c0424e64>] (drm_dp_i2c_xfer+0x98/0x214)
[<c0424e64>] (drm_dp_i2c_xfer) from [<c057b2d8>] (__i2c_transfer+0x140/0x29c)
[<c057b2d8>] (__i2c_transfer) from [<c057b4a4>] (i2c_transfer+0x70/0xe4)
[<c057b4a4>] (i2c_transfer) from [<c0441de4>] (drm_do_probe_ddc_edid+0xb4/0x114)
[<c0441de4>] (drm_do_probe_ddc_edid) from [<c0441e5c>] (drm_probe_ddc+0x18/0x28)
[<c0441e5c>] (drm_probe_ddc) from [<c0445728>] (drm_get_edid+0x124/0x2d4)
[<c0445728>] (drm_get_edid) from [<c0465ea0>] (analogix_dp_get_modes+0x90/0x114)
[<c0465ea0>] (analogix_dp_get_modes) from [<c0425e8c>] (drm_helper_probe_single_connector_modes+0x198/0x68c)
[<c0425e8c>] (drm_helper_probe_single_connector_modes) from [<c04325d4>] (drm_setup_crtcs+0x1b4/0xd18)
[<c04325d4>] (drm_setup_crtcs) from [<c04344a8>] (drm_fb_helper_hotplug_event+0x94/0xd0)
[<c04344a8>] (drm_fb_helper_hotplug_event) from [<c0425a50>] (drm_kms_helper_hotplug_event+0x24/0x28)
[<c0425a50>] (drm_kms_helper_hotplug_event) from [<c04263ec>] (output_poll_execute+0x6c/0x174)
[<c04263ec>] (output_poll_execute) from [<c0136f18>] (process_one_work+0x188/0x3fc)
[<c0136f18>] (process_one_work) from [<c01371f4>] (worker_thread+0x30/0x4b8)
[<c01371f4>] (worker_thread) from [<c013daf8>] (kthread+0x128/0x164)
[<c013daf8>] (kthread) from [<c0108510>] (ret_from_fork+0x14/0x24)
Code: 0a000002 ea000009 e2544001 0a00004a (e59537c8)
---[ end trace cddc7919c79f7878 ]---
Reported-by: Misha Komarovskiy <zombah@gmail.com>
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20171121074936.22520-1-m.szyprowski@samsung.com
|
|
The 10.4 firmware defines this as a 3-bit field, as does the
mac80211 stack. The 4th bit is defined as CONF_IMPLICIT_BF
at least in the firmware header I have seen. This patch
fixes the ath10k wmi header to match the firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Replace ntohs with be16_to_cpu to do endian conversions for ethhdr
h_proto assignment.
Signed-off-by: Kenneth Lu <kuohsianglu@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
At the moment, spectral scan support, and with it RELAY, is always enabled
with ATH10K_DEBUGFS. Spectral scan support is currently the only user of
RELAY in ath10k, and it unconditionally reserves a relay channel.
Having debugfs support in ath10k is often useful even on very small
embedded routers, where we'd rather like to avoid the code size and RAM
usage of the relay support. While ath10k-based devices usually have more
resources than ath9k-based ones, it makes sense to keep the configuration
symmetric to ath9k, so the same base kernel without RELAY can be used for
both ath9k and ath10k hardware.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
At the moment, spectral scan support, and with it RELAY, is always enabled
with ATH9K[_HTC]_DEBUGFS. Spectral scan support is currently the only user
of RELAY in ath9k, and it unconditionally reserves a relay channel.
Having debugfs support in ath9k is often useful even on very small embedded
routers, where we'd rather like to avoid the code size and RAM usage of the
relay support.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The dump format uses 64-bit timestamps already, but calling
getnstimeofday() only returns a 32-bit number on 32-bit architectures,
so that will overflow in y2038.
This changes it to use ktime_get_real_ts64() instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
To get rid of W=1 warning: variable ‘ies_len’ set but not used.
Variable ies_len is being assigned but never read.
Signed-off-by: Kenneth Lu <kuohsianglu@gmail.com>
Reviewed-by: Steve deRosier <derosier@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Third batch of iwlwifi patches intended for 4.15.
* Tell mac80211 when the MAC has been stripped (9000 series);
* Tell mac80211 when the IVC has been stripped (9000 series);
* Add 2 new PCI IDs, one for 9000 and one for 22000;
* Fix a queue hang due during ROC.
|
|
When I run make W=1 on gcc (Debian 7.2.0-16) 7.2.0 I got an error for
the first run, all next ones are okay.
CC [M] drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.o
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:2078: error: Cannot parse struct or union!
scripts/Makefile.build:310: recipe for target 'drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.o' failed
Seems like something happened with W=1 and wrong kernel doc format.
As a quick fix remove dubious /** in the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
No need to get into the submenu to disable all SSB-related
config entries.
This makes it easier to disable all SSB config options
without entering the submenu. It will also enable one
to see that en/dis-abled state from the outside menu.
This is only intended to change menuconfig UI, not change
the config dependencies.
Signed-off-by: Vincent Legoll <vincent.legoll@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
MT76x2e is a 2x2 PCIe 802.11ac chipset by MediaTek. This driver has full
support for AP, station, ad-hoc, mesh and monitor mode.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
