| Age | Commit message (Collapse) | Author |
|---|
|
The buffers mapping of the Multi-Packet WQEs (of Striding RQ)
is done via UMR posts, one UMR WQE per an RX MPWQE.
A single MPWQE is capable of serving many incoming packets,
usually larger than the budget of a single napi cycle.
Hence, posting a single UMR WQE per napi cycle (and handling its
completion in the next cycle) works fine in many common cases,
but not always.
When an XDP program is loaded, every MPWQE is capable of serving less
packets, to satisfy the packet-per-page requirement.
Thus, for the same number of packets more MPWQEs (and UMR posts)
are needed (twice as much for the default MTU), giving less latency
room for the UMR completions.
In this patch, we add support for multiple outstanding UMR posts,
to allow faster gap closure between consuming MPWQEs and reposting
them back into the WQ.
For better SW and HW locality, we combine the UMR posts in bulks of
(at least) two.
This is expected to improve packet rate in high CPU scale.
Performance test:
As expected, huge improvement in large-scale (48 cores).
xdp_redirect_map, 64B UDP multi-stream.
Redirect from ConnectX-5 100Gbps to ConnectX-6 100Gbps.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz.
Before: Unstable, 7 to 30 Mpps
After: Stable, at 70.5 Mpps
No degradation in other tested scenarios.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
|
|
Kavya Sree Kotagiri says:
====================
net: phy: mscc: Improvements to VSC8514 PHY driver.
The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X, can communicate with the MAC via QSGMII.
The MAC interface protocol for each port within QSGMII can
be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is
connecting to supports this functionality.
VSC8514 also supports SGMII MAC-side autonegotiation on each individual
port, downshifting, can set the blinking pattern of each of its 4 LEDs,
SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection.
This patch series adds support for 10BASE-T, 100BASE-TX, and
1000BASE-T, QSGMII link with the MAC, downshifting, HP Auto-MDIX
detection and blinking pattern for its 4 LEDs.
The GPIO register bank is a set of registers that are common to all
PHYs in the package. So any modification in any register of this bank
affects all PHYs of the package.
If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.
Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
This patch series adds support for VSC8514 in Microsemi driver(mscc.c)
and removes support from Vitesse driver(vitesse.c).
v8
- mscc: Added appropriate code using phy_modify() in vsc8514_config_init().
v7
- mscc: Handled return values in vsc8514_config_init().
v6
- mscc: Added proper return value in vsc85xx_csr_ctrl_phy_read().
- mscc: Replaced __mdiobus_write and__mdiobus_read with __phy_write and __phy_read resp.
- mscc: Replaced register addresses in 8514_config_init() with proper constants.
v5
- mscc: Added return error statements for few function calls.
- mscc: Added comments in vsc85xx_csr_ctrl_phy_read() and vsc85xx_csr_ctrl_phy_write()
v4
- mscc: Removed features settings
- mscc: Removed aneg_done settings.
v3
- mscc: Used BIT(x) for PHY_MCB_S6G_WRITE and PHY_MCB_S6G_READ
instead of hex.
- mscc: Replaced magic numbers with proper constants.
- mscc: Handled delays and timeouts at appropriate points.
- mscc: Added comments/explanation where requested.
v2
- mscc: Sorted variable declarations in reverse christmas tree order.
v1
- Added 0/2 file.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for VSC8514 in Microsemi driver (mscc.c)
with more features.
Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X, can communicate with the MAC via QSGMII.
The MAC interface protocol for each port within QSGMII can
be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is
connecting to supports this functionality.
VSC8514 also supports SGMII MAC-side autonegotiation on each individual
port, downshifting, can set the blinking pattern of each of its 4 LEDs,
SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection.
This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T,
QSGMII link with the MAC, downshifting, HP Auto-MDIX detection
and blinking pattern for its 4 LEDs.
The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.
If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.
Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/nfc/st95hf/st95hf.ko | grep alias
alias: spi:st95hf
After this patch:
modinfo drivers/nfc/st95hf/st95hf.ko | grep alias
alias: spi:st95hf
alias: of:N*T*Cst,st95hfC*
alias: of:N*T*Cst,st95hf
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
After this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
alias: of:N*T*Cmicrel,ksz8795C*
alias: of:N*T*Cmicrel,ksz8795
alias: of:N*T*Cmicrel,ksz8864C*
alias: of:N*T*Cmicrel,ksz8864
alias: of:N*T*Cmicrel,ks8995C*
alias: of:N*T*Cmicrel,ks8995
Reported-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Daniel Gomez <dagmcr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default m88e151x LED configuration is 0x1177, used LED[0]
for 1000M link, LED[1] for 100M link, and LED[2] for active.
But for some boards, which use LED[0] for link, and LED[1] for
active, prefer to be 0x1040. To be compatible with this case,
this patch defines a new dev_flag, and set it before connect
phy in HNS3 driver. When phy initializing, using the new
LED configuration if this dev_flag is set.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
size = struct_size(instance, entry, count);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch enables enough time to ROME controller to bootup
after we bring the enable pin out of reset.
Fixes: 05ba533c5c11 ("Bluetooth: hci_qca: Add serdev support").
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Rocky Liao <rjliao@codeaurora.org>
Tested-by: Rocky Liao <rjliao@codeaurora.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The code path for Macs goes through bcm_apple_get_resources(), which
skips over the code that sets up the regulator supplies. As a result,
the call to regulator_bulk_enable() / regulator_bulk_disable() results
in a NULL pointer dereference.
This was reported on the kernel.org Bugzilla, bug 202963.
Unbreak Broadcom Bluetooth support on Intel Macs by checking if the
supplies were set up before enabling or disabling them.
The same does not need to be done for the clocks, as the common clock
framework API checks for NULL pointers.
Fixes: 75d11676dccb ("Bluetooth: hci_bcm: Add support for regulator supplies")
Cc: <stable@vger.kernel.org> # 5.0.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In ext_adv_report_event rssi comes before data (not after data as
in legacy adv_report_evt) so "+ 1" is not required in the ptr arithmatic
to point to next report.
Signed-off-by: Jaganath Kanakkassery <jaganath.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add the device ID for the BT/FM/GPS combo chip BCM2076 (rev B1)
used in the AMPAK AP6476 WiFi/BT/FM/GPS module.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
NEXTHDR_MAX is 255. What happens here is that we take a u8 value
"hdr->nexthdr" from the network and then look it up in
lowpan_nexthdr_nhcs[]. The problem is that if hdr->nexthdr is 0xff then
we read one element beyond the end of the array so the array needs to
be one element larger.
Fixes: 92aa7c65d295 ("6lowpan: add generic nhc layer interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Acked-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The BCM43341B has the default MAC address 43:34:1B:00:1F:AC if none
is given. This address was found when enabling Bluetooth on multiple
Intel Edison modules. It also contains the sequence 43341B, the name
the chip identifies itself as. Using the same BD_ADDR is problematic
when having multiple Intel Edison modules in each others range.
The default address also has the LAA (locally administered address)
bit set which prevents a BNEP device from being created, needed for
BT tethering.
Add this to the list of black listed default MAC addresses and let
the user configure a valid one using f.i.
`btmgmt -i hci0 public-addr xx:xx:xx:xx:xx:xx`
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ferry Toth <ftoth@exalondelft.nl>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Struct ca is copied from userspace. It is not checked whether the "name"
field is NULL terminated, which allows local users to obtain potentially
sensitive information from kernel stack memory, via a HIDPCONNADD command.
This vulnerability is similar to CVE-2011-1079.
Signed-off-by: Young Xiao <YangX92@hotmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
|
|
This patch adds support for Marvell 88W8987 chipset with SDIO interface.
Register offsets and supported feature flags are updated. The corresponding
firmware image file shall be "mrvl/sd8987_uapsta.bin".
Signed-off-by: Tamás Szűcs <tszucs@protonmail.ch>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Stanislav Fomichev says:
====================
Currently, when eth_get_headlen calls flow dissector, it doesn't pass any
skb. Because we use passed skb to lookup associated networking namespace
to find whether we have a BPF program attached or not, we always use
C-based flow dissector in this case.
The goal of this patch series is to add new networking namespace argument
to the eth_get_headlen and make BPF flow dissector programs be able to
work in the skb-less case.
The series goes like this:
* use new kernel context (struct bpf_flow_dissector) for flow dissector
programs; this makes it easy to distinguish between skb and no-skb
case and supports calling BPF flow dissector on a chunk of raw data
* convert BPF_PROG_TEST_RUN to use raw data
* plumb network namespace into __skb_flow_dissect from all callers
* handle no-skb case in __skb_flow_dissect
* update eth_get_headlen to include net namespace argument and
convert all existing users
* add selftest to make sure bpf_skb_load_bytes is not allowed in
the no-skb mode
* extend test_progs to exercise skb-less flow dissection as well
* stop adjusting nhoff/thoff by ETH_HLEN in BPF_PROG_TEST_RUN
v6:
* more suggestions by Alexei:
* eth_get_headlen now takes net dev, not net namespace
* test skb-less case via tun eth_get_headlen
* fix return errors in bpf_flow_load
* don't adjust nhoff/thoff by ETH_HLEN
v5:
* API changes have been submitted via bpf/stable tree
v4:
* prohibit access to vlan fields as well (otherwise, inconsistent
between skb/skb-less cases)
* drop extra unneeded check for skb->vlan_present in bpf_flow.c
v3:
* new kernel xdp_buff-like context per Alexei suggestion
* drop skb_net helper
* properly clamp flow_keys->nhoff
v2:
* moved temporary skb from stack into percpu (avoids memset of ~200 bytes
per packet)
* tightened down access to __sk_buff fields from flow dissector programs to
avoid touching shinfo (whitelist only relevant fields)
* addressed suggestions from Willem
====================
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Now that we use skb-less flow dissector let's return true nhoff and
thoff. We used to adjust them by ETH_HLEN because that's how it was
done in the skb case. For VLAN tests that looks confusing: nhoff is
pointing to vlan parts :-\
Warning, this is an API change for BPF_PROG_TEST_RUN! Feel free to drop
if you think that it's too late at this point to fix it.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Right now we incorrectly return 'ret' which is always zero at that
point.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Export last_dissection map from flow dissector and use a known place in
tun driver to trigger BPF flow dissection.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
When flow dissector is called without skb, we want to make sure
bpf_skb_load_bytes invocations return error. Add small test which tries
to read single byte from a packet.
bpf_skb_load_bytes should always fail under BPF_PROG_TEST_RUN because
it was converted to the skb-less mode.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Update all users of eth_get_headlen to pass network device, fetch
network namespace from it and pass it down to the flow dissector.
This commit is a noop until administrator inserts BPF flow dissector
program.
Cc: Maxim Krasnyansky <maxk@qti.qualcomm.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
When called without skb, gather all required data from the
__skb_flow_dissect's arguments and use recently introduces
no-skb mode of bpf flow dissector.
Note: WARN_ON_ONCE(!net) will now trigger for eth_get_headlen users.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
This new argument will be used in the next patches for the
eth_get_headlen use case. eth_get_headlen calls flow dissector
with only data (without skb) so there is currently no way to
pull attached BPF flow dissector program. With this new argument,
we can amend the callers to explicitly pass network namespace
so we can use attached BPF program.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Now that we have bpf_flow_dissect which can work on raw data,
use it when doing BPF_PROG_TEST_RUN for flow dissector.
Simplifies bpf_prog_test_run_flow_dissector and allows us to
test no-skb mode.
Note, that previously, with bpf_flow_dissect_skb we used to call
eth_type_trans which pulled L2 (ETH_HLEN) header and we explicitly called
skb_reset_network_header. That means flow_keys->nhoff would be
initialized to 0 (skb_network_offset) in init_flow_keys.
Now we call bpf_flow_dissect with nhoff set to ETH_HLEN and need
to undo it once the dissection is done to preserve the existing behavior.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
struct bpf_flow_dissector has a small subset of sk_buff fields that
flow dissector BPF program is allowed to access and an optional
pointer to real skb. Real skb is used only in bpf_skb_load_bytes
helper to read non-linear data.
The real motivation for this is to be able to call flow dissector
from eth_get_headlen context where we don't have an skb and need
to dissect raw bytes.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Add runtime PM support to btmtksdio. With this way, there will be the
benefit of the device entering the more power saving state once it is
been a while data traffic is idle.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Accumulate hdev->stat.byte_rx only for valid packets as btmtkuart doing.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add a register bit definition about CHLPCR bit 8 because the bit is quite
different in the meaning between reading and writing that bit.
The patch adds a definition particularly for the bit read to avoid the
confusion about using write definition to read the bit.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
bt_dev logging macros already include a newline at each output
so drop these unnecessary additional newlines in the driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The EFI stub is entered with the caches and MMU enabled by the
firmware, and once the stub is ready to hand over to the decompressor,
we clean and disable the caches.
The cache clean routines use CP15 barrier instructions, which can be
disabled via SCTLR. Normally, when using the provided cache handling
routines to enable the caches and MMU, this bit is enabled as well.
However, but since we entered the stub with the caches already enabled,
this routine is not executed before we call the cache clean routines,
resulting in undefined instruction exceptions if the firmware never
enabled this bit.
So set the bit explicitly in the EFI entry code, but do so in a way that
guarantees that the resulting code can still run on v6 cores as well
(which are guaranteed to have CP15 barriers enabled)
Cc: <stable@vger.kernel.org> # v4.9+
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
When CONFIG_ARM_MPU is not defined, the base address of v7M SCB register
is not initialized with correct value. This prevents enabling I/D caches
when the L1 cache poilcy is applied in kernel.
Fixes: 3c24121039c9da14692eb48f6e39565b28c0f3cf ("ARM: 8756/1: NOMMU: Postpone MPU activation till __after_proc_init")
Signed-off-by: Tigran Tadevosyan <tigran.tadevosyan@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Naresh Kamboju recently reported that the function-graph tracer crashes
on ARM. The function-graph tracer assumes that the kernel is built with
frame pointers.
We explicitly disabled the function-graph tracer when building Thumb2,
since the Thumb2 ABI doesn't have frame pointers.
We recently changed the way the unwinder method was selected, which
seems to have made it more likely that we can end up with the function-
graph tracer enabled but without the kernel built with frame pointers.
Fix up the function graph tracer dependencies so the option is not
available when we have no possibility of having frame pointers, and
adjust the dependencies on the unwinder option to hide the non-frame
pointer unwinder options if the function-graph tracer is enabled.
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Since commit 222b5f044159 ("drm/sched: Refactor ring mirror list
handling."), drm_sched_hw_job_reset is no longer there, so let's adjust
the doc comment accordingly.
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
There is a spelling mistake in a BT_DBG debug message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Fixed warning: incorrect type in assignment reported by kbuild test robot.
The detailed warning is shown as below.
make ARCH=x86_64 allmodconfig
make C=1 CF='-fdiagnostic-prefix -D__CHECK_ENDIAN__'
All warnings (new ones prefixed by >>):
btmtkuart.c:671:18: sparse: warning: incorrect type in assignment
(different base types)
btmtkuart.c:671:18: sparse: expected unsigned int [usertype] baudrate
btmtkuart.c:671:18: sparse: got restricted __le32 [usertype]
sparse warnings: (new ones prefixed by >>)
btmtkuart.c:671:18: sparse: warning: incorrect type in assignment
(different base types)
btmtkuart.c:671:18: sparse: expected unsigned int [usertype] baudrate
btmtkuart.c:671:18: sparse: got restricted __le32 [usertype]
vim +671 drivers/bluetooth/btmtkuart.c
659
660 static int btmtkuart_change_baudrate(struct hci_dev *hdev)
661 {
662 struct btmtkuart_dev *bdev = hci_get_drvdata(hdev);
663 struct btmtk_hci_wmt_params wmt_params;
664 u32 baudrate;
665 u8 param;
666 int err;
667
668 /* Indicate the device to enter the probe state the host is
669 * ready to change a new baudrate.
670 */
> 671 baudrate = cpu_to_le32(bdev->desired_speed);
672 wmt_params.op = MTK_WMT_HIF;
Fixes: 22eaf6c9946a ("Bluetooth: mediatek: add support for MediaTek MT7663U and MT7668U UART devices")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Fixed all the below warnings. They would probably cause the following
error handling path would use the uninitialized value and then produce
unexpected behavior.
drivers/bluetooth/btmtksdio.c:470:2: warning: ‘old_len’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
print_hex_dump(KERN_ERR, "err sdio rx: ", DUMP_PREFIX_NONE, 4, 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
old_data, old_len, true);
~~~~~~~~~~~~~~~~~~~~~~~~
drivers/bluetooth/btmtksdio.c:376:15: note: ‘old_len’ was declared here
unsigned int old_len;
^~~~~~~
drivers/bluetooth/btmtksdio.c:470:2: warning: ‘old_data’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
print_hex_dump(KERN_ERR, "err sdio rx: ", DUMP_PREFIX_NONE, 4, 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
old_data, old_len, true);
~~~~~~~~~~~~~~~~~~~~~~~~
drivers/bluetooth/btmtksdio.c:375:17: note: ‘old_data’ was declared here
unsigned char *old_data;
^~~~~~~~
v2: Remove old_len and old_data because the error path for sdio_readsb also
seems wrong. And change the prefix from "mediatek" to "btmtksdio".
Fixes: d74eef2834b5 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Macro module_sdio_driver is used for drivers whose init and exit paths
only register and unregister to SDIO API. So remove boilerplate code to
make code simpler by using module_sdio_driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Macro module_sdio_driver is used for drivers whose init and exit paths
only register and unregister to SDIO API. So remove boilerplate code to
make code simpler by using module_sdio_driver.
Suggested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch introduces the module_sdio_driver macro which is a convenience
macro for SDIO driver modules similar to module_usb_driver. It is intended
to be used by drivers which init/exit section does nothing but register/
unregister the SDIO driver. By using this macro it is possible to eliminate
a few lines of boilerplate code per SDIO driver.
Suggested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add return check for security level set for socket interface since
stack will check the return value.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
l2cap_le_flowctl_init was reseting the tx_credits which works only for
outgoing connection since that set the tx_credits on the response, for
incoming connections that was not the case which leaves the channel
without any credits causing it to be suspended.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org # 4.20+
|
|
Rename the misspelled struct 'qca_bardrate' to 'qca_baudrate'
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Many functions obtain a 'struct qca_serdev' only to read the btsoc_type
field. Add a helper function that encapsulates this.
This also fixes crashes observed on platforms with ROME controllers
that are instantiated through ldisc and not as serdev clients. The
crashes are caused by NULL pointer dereferentiations, which stem from
the driver's assumption that a QCA HCI device is always associated with
a serdev device.
Fixes: fa9ad876b8e0 ("Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990")
Reported-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds the support of enabling MT7663S and MT7668S SDIO-based
Bluetooth function.
There are quite many differences between MT766[3,8]S and standard
Bluetooth SDIO devices such as Type-A and Type-B devices. For example,
MT766[3,8]S have its own SDIO registers layout, definition, SDIO packet
format, and the specific flow should be programmed on them to complete
the device initialization and low power control and so on.
Currently, there are many independent programming sequences from the
transport which are exactly the same as the ones in btusb.c about MediaTek
support [1] and btmtkuart.c. We can try to split the transport independent
Bluetooth setups on the advance, place them into the common files and allow
varous transport drivers to reuse them in the future.
[1] http://lists.infradead.org/pipermail/linux-mediatek/2019-January/017074.html
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The SDIO identifier for MediaTek Bluetooth devices were defined in the
MediaTek Bluetooth driver. Moving the definitions in MMC header file
seems common sense.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Since commit 09bb839434b we don't use the state argument for any sort
of on-stack caching in the io read and write path. Remove the stale
and unused argument from them, and bubble it up to __io_submit_sqe()
and down to io_prep_rw().
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In order to make sure that the plane color space gets reset correctly.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Initialize the flow input colorspaces to unknown and reset to that value
when the channel gets disabled. This avoids the state getting mixed up
with a previous mode.
Also keep the CSC settings for the background flow intact when disabling
the foreground flow.
Root-caused-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
