| Age | Commit message (Collapse) | Author |
|---|
|
Simplest setup to reproduce the issue: connect 2 ports of the
LS1028A-RDB together (eno0 with swp0) and run:
$ ip link set eno0 up && ip link set swp0 up
$ tc qdisc replace dev swp0 parent root handle 100 taprio num_tc 8 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 map 0 1 2 3 4 5 6 7 \
base-time 0 sched-entry S 20 300000 sched-entry S 10 200000 \
sched-entry S 20 300000 sched-entry S 48 200000 \
sched-entry S 20 300000 sched-entry S 83 200000 \
sched-entry S 40 300000 sched-entry S 00 200000 flags 2
$ ptp4l -i eno0 -f /etc/linuxptp/configs/gPTP.cfg -m &
$ ptp4l -i swp0 -f /etc/linuxptp/configs/gPTP.cfg -m
One will observe that the PTP state machine on swp0 starts
synchronizing, then it attempts to do a clock step, and after that, it
never fails to recover from the condition below.
ptp4l[82.427]: selected best master clock 00049f.fffe.05f627
ptp4l[82.428]: port 1 (swp0): MASTER to UNCALIBRATED on RS_SLAVE
ptp4l[83.252]: port 1 (swp0): UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED
ptp4l[83.886]: rms 4537731277 max 9075462553 freq -18518 +/- 11467 delay 818 +/- 0
ptp4l[84.170]: timed out while polling for tx timestamp
ptp4l[84.171]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[84.172]: port 1 (swp0): send peer delay request failed
ptp4l[84.173]: port 1 (swp0): clearing fault immediately
ptp4l[84.269]: port 1 (swp0): SLAVE to LISTENING on INIT_COMPLETE
ptp4l[85.303]: timed out while polling for tx timestamp
ptp4l[84.171]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[84.172]: port 1 (swp0): send peer delay request failed
ptp4l[84.173]: port 1 (swp0): clearing fault immediately
ptp4l[84.269]: port 1 (swp0): SLAVE to LISTENING on INIT_COMPLETE
ptp4l[85.303]: timed out while polling for tx timestamp
ptp4l[85.304]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[85.305]: port 1 (swp0): send peer delay response failed
ptp4l[85.306]: port 1 (swp0): clearing fault immediately
ptp4l[86.304]: timed out while polling for tx timestamp
A hint is given by the non-zero statistics for dropped packets which
were expecting hardware TX timestamps:
$ ethtool --include-statistics -T swp0
(...)
Statistics:
tx_pkts: 30
tx_lost: 11
tx_err: 0
We know that when PTP clock stepping takes place (from ocelot_ptp_settime64()
or from ocelot_ptp_adjtime()), vsc9959_tas_clock_adjust() is called.
Another interesting hint is that placing an early return in
vsc9959_tas_clock_adjust(), so as to neutralize this function, fixes the
issue and TX timestamps are no longer dropped.
The debugging function written by me and included below is intended to
read the GCL RAM, after the admin schedule became operational, through
the two status registers available for this purpose:
QSYS_GCL_STATUS_REG_1 and QSYS_GCL_STATUS_REG_2.
static void vsc9959_print_tas_gcl(struct ocelot *ocelot)
{
u32 val, list_length, interval, gate_state;
int i, err;
err = read_poll_timeout(ocelot_read, val,
!(val & QSYS_PARAM_STATUS_REG_8_CONFIG_PENDING),
10, 100000, false, ocelot, QSYS_PARAM_STATUS_REG_8);
if (err) {
dev_err(ocelot->dev,
"Failed to wait for TAS config pending bit to clear: %pe\n",
ERR_PTR(err));
return;
}
val = ocelot_read(ocelot, QSYS_PARAM_STATUS_REG_3);
list_length = QSYS_PARAM_STATUS_REG_3_LIST_LENGTH_X(val);
dev_info(ocelot->dev, "GCL length: %u\n", list_length);
for (i = 0; i < list_length; i++) {
ocelot_rmw(ocelot,
QSYS_GCL_STATUS_REG_1_GCL_ENTRY_NUM(i),
QSYS_GCL_STATUS_REG_1_GCL_ENTRY_NUM_M,
QSYS_GCL_STATUS_REG_1);
interval = ocelot_read(ocelot, QSYS_GCL_STATUS_REG_2);
val = ocelot_read(ocelot, QSYS_GCL_STATUS_REG_1);
gate_state = QSYS_GCL_STATUS_REG_1_GATE_STATE_X(val);
dev_info(ocelot->dev, "GCL entry %d: states 0x%x interval %u\n",
i, gate_state, interval);
}
}
Calling it from two places: after the initial QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE
performed by vsc9959_qos_port_tas_set(), and after the one done by
vsc9959_tas_clock_adjust(), I notice the following difference.
From the tc-taprio process context, where the schedule was initially
configured, the GCL looks like this:
mscc_felix 0000:00:00.5: GCL length: 8
mscc_felix 0000:00:00.5: GCL entry 0: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 1: states 0x10 interval 200000
mscc_felix 0000:00:00.5: GCL entry 2: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 3: states 0x48 interval 200000
mscc_felix 0000:00:00.5: GCL entry 4: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 5: states 0x83 interval 200000
mscc_felix 0000:00:00.5: GCL entry 6: states 0x40 interval 300000
mscc_felix 0000:00:00.5: GCL entry 7: states 0x0 interval 200000
But from the ptp4l clock stepping process context, when the
vsc9959_tas_clock_adjust() hook is called, the GCL RAM of the
operational schedule now looks like this:
mscc_felix 0000:00:00.5: GCL length: 8
mscc_felix 0000:00:00.5: GCL entry 0: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 1: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 2: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 3: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 4: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 5: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 6: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 7: states 0x0 interval 0
I do not have a formal explanation, just experimental conclusions.
It appears that after triggering QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE
for a port's TAS, the GCL entry RAM is updated anyway, despite what the
documentation claims: "Specify the time interval in
QSYS::GCL_CFG_REG_2.TIME_INTERVAL. This triggers the actual RAM
write with the gate state and the time interval for the entry number
specified". We don't touch that register (through vsc9959_tas_gcl_set())
from vsc9959_tas_clock_adjust(), yet the GCL RAM is updated anyway.
It seems to be updated with effectively stale memory, which in my
testing can hold a variety of things, including even pieces of the
previously applied schedule, for particular schedule lengths.
As such, in most circumstances it is very difficult to pinpoint this
issue, because the newly updated schedule would "behave strangely",
but ultimately might still pass traffic to some extent, due to some
gate entries still being present in the stale GCL entry RAM. It is easy
to miss.
With the particular schedule given at the beginning, the GCL RAM
"happens" to be reproducibly rewritten with all zeroes, and this is
consistent with what we see: when the time-aware shaper has gate entries
with all gates closed, traffic is dropped on TX, no wonder we can't
retrieve TX timestamps.
Rewriting the GCL entry RAM when reapplying the new base time fixes the
observed issue.
Fixes: 8670dc33f48b ("net: dsa: felix: update base time of time-aware shaper when adjusting PTP time")
Reported-by: Richie Pearn <richard.pearn@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250426144859.3128352-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the mtk_poll_rx() function detects the MTK_RESETTING flag, it will
jump to release_desc and refill the high word of the SDP on the 4GB RFB.
Subsequently, mtk_rx_clean will process an incorrect SDP, leading to a
panic.
Add patch from MediaTek's SDK to resolve this.
Fixes: 2d75891ebc09 ("net: ethernet: mtk_eth_soc: support 36-bit DMA addressing on MT7988")
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/71f47ea785699c6aa3b922d66c2bdc1a43da25b1
Signed-off-by: Chad Monroe <chad@monroe.io>
Link: https://patch.msgid.link/4adc2aaeb0fb1b9cdc56bf21cf8e7fa328daa345.1745715843.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 1a931c4f5e68 ("igc: add lock preventing multiple simultaneous PTM
transactions") added a new mutex to protect concurrent PTM transactions.
This lock is acquired in igc_ptp_reset() in order to ensure the PTM
registers are properly disabled after a device reset.
The flow where the lock is acquired already holds a spinlock, so acquiring
a mutex leads to a sleep-while-locking bug, reported both by smatch,
and the kernel test robot.
The critical section in igc_ptp_reset() does correctly use the
readx_poll_timeout_atomic variants, but the standard PTM flow uses regular
sleeping variants. This makes converting the mutex to a spinlock a bit
tricky.
Instead, re-order the locking in igc_ptp_reset. Acquire the mutex first,
and then the tmreg_lock spinlock. This is safe because there is no other
ordering dependency on these locks, as this is the only place where both
locks were acquired simultaneously. Indeed, any other flow acquiring locks
in that order would be wrong regardless.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Fixes: 1a931c4f5e68 ("igc: add lock preventing multiple simultaneous PTM transactions")
Link: https://lore.kernel.org/intel-wired-lan/Z_-P-Hc1yxcw0lTB@stanley.mountain/
Link: https://lore.kernel.org/intel-wired-lan/202504211511.f7738f5d-lkp@intel.com/T/#u
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Before the referenced commit, the shutdown just called idpf_remove(),
this way IDPF_REMOVE_IN_PROG was protecting us from the serv_task
rescheduling reset. Without this flag set the shutdown process is
vulnerable to HW reset or any other triggering conditions (such as
default mailbox being destroyed).
When one of conditions checked in idpf_service_task becomes true,
vc_event_task can be rescheduled during shutdown, this leads to accessing
freed memory e.g. idpf_req_rel_vector_indexes() trying to read
vport->q_vector_idxs. This in turn causes the system to become defunct
during e.g. systemctl kexec.
Considering using IDPF_REMOVE_IN_PROG would lead to more heavy shutdown
process, instead just cancel the serv_task before cancelling
adapter->serv_task before cancelling adapter->vc_event_task to ensure that
reset will not be scheduled while we are doing a shutdown.
Fixes: 4c9106f4906a ("idpf: fix adapter NULL pointer dereference on reboot")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In case of failing on rss_data->rss_key allocation the function is
freeing vport without freeing earlier allocated q_vector_idxs. Fix it.
Move from freeing in error branch to goto scheme.
Fixes: d4d558718266 ("idpf: initialize interrupts and enable vport")
Reviewed-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Suggested-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"Renesas SDHI fixes:
- Fix error-paths in probe
- Fix build-error when CONFIG_REGULATOR is unset"
* tag 'mmc-v6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: renesas_sdhi: disable clocks if registering regulator failed
mmc: renesas_sdhi: add regulator dependency
mmc: renesas_sdhi: Fix error handling in renesas_sdhi_probe
|
|
This bit is necessary to receive packets from the internal PHY.
Without this bit set, no activity occurs on the interface.
Normally u-boot sets this bit, but if u-boot is compiled without
net support, the interface will be up but without any activity.
If bit is set once, it will work until the IP is powered down or reset.
The vendor SDK sets this bit along with the PHY_ID bits.
Signed-off-by: Da Xue <da@libre.computer>
Fixes: 9a24e1ff4326 ("net: mdio: add amlogic gxl mdio mux support")
Link: https://patch.msgid.link/20250425192009.1439508-1-da@libre.computer
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As it's name suggests, parse_eeprom() parses EEPROM data.
This is done by reading data, 16 bits at a time as follows:
for (i = 0; i < 128; i++)
((__le16 *) sromdata)[i] = cpu_to_le16(read_eeprom(np, i));
sromdata is at the same memory location as psrom.
And the type of psrom is a pointer to struct t_SROM.
As can be seen in the loop above, data is stored in sromdata, and thus psrom,
as 16-bit little-endian values.
However, the integer fields of t_SROM are host byte order integers.
And in the case of led_mode this leads to a little endian value
being incorrectly treated as host byte order.
Looking at rio_set_led_mode, this does appear to be a bug as that code
masks led_mode with 0x1, 0x2 and 0x8. Logic that would be effected by a
reversed byte order.
This problem would only manifest on big endian hosts.
Found by inspection while investigating a sparse warning
regarding the crc field of t_SROM.
I believe that warning is a false positive. And although I plan
to send a follow-up to use little-endian types for other the integer
fields of PSROM_t I do not believe that will involve any bug fixes.
Compile tested only.
Fixes: c3f45d322cbd ("dl2k: Add support for IP1000A-based cards")
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250425-dlink-led-mode-v1-1-6bae3c36e736@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull fsnotify fix from Jan Kara:
"A fix for the recently merged mount notification support"
* tag 'fsnotify_for_v6.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
selftests/fs/mount-notify: test also remove/flush of mntns marks
fanotify: fix flush of mntns marks
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform drivers fixes from Ilpo Järvinen:
"Fixes and new HW support
- amd/pmc: Require at least 2.5 seconds between HW sleep cycles
- alienware-wmi-wmax:
- Add support for Alienware m15 R7
- Fix error handling to avoid uninitialized variable
- asus-wmi: Disable OOBE state also on resume
- ideapad-laptop: Support a few new buttons
- intel/hid: Add Panther Lake support
- intel-uncore-freq: Fix missing uncore sysfs during CPU hotplug"
* tag 'platform-drivers-x86-v6.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: ideapad-laptop: add support for some new buttons
platform/x86: asus-wmi: Disable OOBE state after resume from hibernation
platform/x86: alienware-wmi-wmax: Add support for Alienware m15 R7
platform/x86/intel: hid: Add Pantherlake support
platform/x86: alienware-wmi-wmax: Fix uninitialized variable due to bad error handling
platform/x86/intel-uncore-freq: Fix missing uncore sysfs during CPU hotplug
platform/x86/amd: pmc: Require at least 2.5 seconds between HW sleep cycles
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock
Pull memblock fixes from Mike Rapoport:
"Fixes for nid setting in memmap_init_reserved_pages():
- pass 'size' rather than 'end' to memblock_set_node() as that
function expects
- fix a corner case when memblock.reserved is doubled at
memmap_init_reserved_pages() and the newly reserved block
won't have nid assigned"
* tag 'fixes-2025-04-29' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock:
memblock tests: add test for memblock_set_node
mm/memblock: repeat setting reserved region nid if array is doubled
mm/memblock: pass size instead of end to memblock_set_node()
|
|
Pull smb server fixes from Steve French:
- Fix three potential use after frees: in session logoff, in krb5 auth,
and in RPC open
- Fix missing rc check in session setup authentication
* tag 'v6.15-rc4-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: fix use-after-free in session logoff
ksmbd: fix use-after-free in kerberos authentication
ksmbd: fix use-after-free in ksmbd_session_rpc_open
smb: server: smb2pdu: check return value of xa_store()
|
|
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-04-22 (ice, idpf)
For ice:
Paul removes setting of ICE_AQ_FLAG_RD in ice_get_set_tx_topo() on
E830 devices.
Xuanqiang Luo adds error check for NULL VF VSI.
For idpf:
Madhu fixes misreporting of, currently, unsupported encapsulated
packets.
====================
Link: https://patch.msgid.link/20250425222636.3188441-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Split offloads into csum, tso and other offloads so that tunneled
packets do not by default have all the offloads enabled.
Stateless offloads for encapsulated packets are not yet supported in
firmware/software but in the driver we were setting the features same as
non encapsulated features.
Fixed naming to clarify CSUM bits are being checked for Tx.
Inherit netdev features to VLAN interfaces as well.
Fixes: 0fe45467a104 ("idpf: add create vport and netdev configuration")
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Madhu Chittim <madhu.chittim@intel.com>
Tested-by: Zachary Goldstein <zachmgoldstein@google.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250425222636.3188441-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As mentioned in the commit baeb705fd6a7 ("ice: always check VF VSI
pointer values"), we need to perform a null pointer check on the return
value of ice_get_vf_vsi() before using it.
Fixes: 6ebbe97a4881 ("ice: Add a per-VF limit on number of FDIR filters")
Signed-off-by: Xuanqiang Luo <luoxuanqiang@kylinos.cn>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250425222636.3188441-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Get Tx Topology AQ command (opcode 0x0418) has different read flag
requirements depending on the hardware/firmware. For E810, E822, and E823
firmware the read flag must be set, and for newer hardware (E825 and E830)
it must not be set.
This results in failure to configure Tx topology and the following warning
message during probe:
DDP package does not support Tx scheduling layers switching feature -
please update to the latest DDP package and try again
The current implementation only handles E825-C but not E830. It is
confusing as we first check ice_is_e825c() and then set the flag in the set
case. Finally, we check ice_is_e825c() again and set the flag for all other
hardware in both the set and get case.
Instead, notice that we always need the read flag for set, but only need
the read flag for get on E810, E822, and E823 firmware. Fix the logic to
check the MAC type and set the read flag in get only on the older devices
which require it.
Fixes: ba1124f58afd ("ice: Add E830 device IDs, MAC type and registers")
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250425222636.3188441-2-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Victor Nogueira says:
====================
net_sched: Adapt qdiscs for reentrant enqueue cases
As described in Gerrard's report [1], there are cases where netem can
make the qdisc enqueue callback reentrant. Some qdiscs (drr, hfsc, ets,
qfq) break whenever the enqueue callback has reentrant behaviour.
This series addresses these issues by adding extra checks that cater for
these reentrant corner cases. This series has passed all relevant test
cases in the TDC suite.
[1] https://lore.kernel.org/netdev/CAHcdcOm+03OD2j6R0=YHKqmy=VgJ8xEOKuP6c7mSgnp-TEJJbw@mail.gmail.com/
====================
Link: https://patch.msgid.link/20250425220710.3964791-1-victor@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add 5 TDC tests that exercise the reentrant enqueue behaviour in drr,
ets, qfq, and hfsc:
- Test DRR's enqueue reentrant behaviour with netem (which caused a
double list add)
- Test ETS's enqueue reentrant behaviour with netem (which caused a double
list add)
- Test QFQ's enqueue reentrant behaviour with netem (which caused a double
list add)
- Test HFSC's enqueue reentrant behaviour with netem (which caused a UAF)
- Test nested DRR's enqueue reentrant behaviour with netem (which caused a
double list add)
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Link: https://patch.msgid.link/20250425220710.3964791-6-victor@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As described in Gerrard's report [1], there are use cases where a netem
child qdisc will make the parent qdisc's enqueue callback reentrant.
In the case of qfq, there won't be a UAF, but the code will add the same
classifier to the list twice, which will cause memory corruption.
This patch checks whether the class was already added to the agg->active
list (cl_is_active) before doing the addition to cater for the reentrant
case.
[1] https://lore.kernel.org/netdev/CAHcdcOm+03OD2j6R0=YHKqmy=VgJ8xEOKuP6c7mSgnp-TEJJbw@mail.gmail.com/
Fixes: 37d9cf1a3ce3 ("sched: Fix detection of empty queues in child qdiscs")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Link: https://patch.msgid.link/20250425220710.3964791-5-victor@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As described in Gerrard's report [1], there are use cases where a netem
child qdisc will make the parent qdisc's enqueue callback reentrant.
In the case of ets, there won't be a UAF, but the code will add the same
classifier to the list twice, which will cause memory corruption.
In addition to checking for qlen being zero, this patch checks whether
the class was already added to the active_list (cl_is_active) before
doing the addition to cater for the reentrant case.
[1] https://lore.kernel.org/netdev/CAHcdcOm+03OD2j6R0=YHKqmy=VgJ8xEOKuP6c7mSgnp-TEJJbw@mail.gmail.com/
Fixes: 37d9cf1a3ce3 ("sched: Fix detection of empty queues in child qdiscs")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Link: https://patch.msgid.link/20250425220710.3964791-4-victor@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As described in Gerrard's report [1], we have a UAF case when an hfsc class
has a netem child qdisc. The crux of the issue is that hfsc is assuming
that checking for cl->qdisc->q.qlen == 0 guarantees that it hasn't inserted
the class in the vttree or eltree (which is not true for the netem
duplicate case).
This patch checks the n_active class variable to make sure that the code
won't insert the class in the vttree or eltree twice, catering for the
reentrant case.
[1] https://lore.kernel.org/netdev/CAHcdcOm+03OD2j6R0=YHKqmy=VgJ8xEOKuP6c7mSgnp-TEJJbw@mail.gmail.com/
Fixes: 37d9cf1a3ce3 ("sched: Fix detection of empty queues in child qdiscs")
Reported-by: Gerrard Tai <gerrard.tai@starlabs.sg>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Link: https://patch.msgid.link/20250425220710.3964791-3-victor@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As described in Gerrard's report [1], there are use cases where a netem
child qdisc will make the parent qdisc's enqueue callback reentrant.
In the case of drr, there won't be a UAF, but the code will add the same
classifier to the list twice, which will cause memory corruption.
In addition to checking for qlen being zero, this patch checks whether the
class was already added to the active_list (cl_is_active) before adding
to the list to cover for the reentrant case.
[1] https://lore.kernel.org/netdev/CAHcdcOm+03OD2j6R0=YHKqmy=VgJ8xEOKuP6c7mSgnp-TEJJbw@mail.gmail.com/
Fixes: 37d9cf1a3ce3 ("sched: Fix detection of empty queues in child qdiscs")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Link: https://patch.msgid.link/20250425220710.3964791-2-victor@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A use-after-free error popped up in stress testing:
[Mon Apr 21 21:21:33 2025] BUG: KFENCE: use-after-free write in pdsc_auxbus_dev_del+0xef/0x160 [pds_core]
[Mon Apr 21 21:21:33 2025] Use-after-free write at 0x000000007013ecd1 (in kfence-#47):
[Mon Apr 21 21:21:33 2025] pdsc_auxbus_dev_del+0xef/0x160 [pds_core]
[Mon Apr 21 21:21:33 2025] pdsc_remove+0xc0/0x1b0 [pds_core]
[Mon Apr 21 21:21:33 2025] pci_device_remove+0x24/0x70
[Mon Apr 21 21:21:33 2025] device_release_driver_internal+0x11f/0x180
[Mon Apr 21 21:21:33 2025] driver_detach+0x45/0x80
[Mon Apr 21 21:21:33 2025] bus_remove_driver+0x83/0xe0
[Mon Apr 21 21:21:33 2025] pci_unregister_driver+0x1a/0x80
The actual device uninit usually happens on a separate thread
scheduled after this code runs, but there is no guarantee of order
of thread execution, so this could be a problem. There's no
actual need to clear the client_id at this point, so simply
remove the offending code.
Fixes: 10659034c622 ("pds_core: add the aux client API")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250425203857.71547-1-shannon.nelson@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- btmtksdio: Check function enabled before doing close
- btmtksdio: Do close if SDIO card removed without close
- btusb: avoid NULL pointer dereference in skb_dequeue()
- btintel_pcie: Avoid redundant buffer allocation
- btintel_pcie: Add additional to checks to clear TX/RX paths
- hci_conn: Fix not setting conn_timeout for Broadcast Receiver
- hci_conn: Fix not setting timeout for BIG Create Sync
* tag 'for-net-2025-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: L2CAP: copy RX timestamp to new fragments
Bluetooth: btintel_pcie: Add additional to checks to clear TX/RX paths
Bluetooth: btmtksdio: Do close if SDIO card removed without close
Bluetooth: btmtksdio: Check function enabled before doing close
Bluetooth: btusb: avoid NULL pointer dereference in skb_dequeue()
Bluetooth: btintel_pcie: Avoid redundant buffer allocation
Bluetooth: hci_conn: Fix not setting timeout for BIG Create Sync
Bluetooth: hci_conn: Fix not setting conn_timeout for Broadcast Receiver
====================
Link: https://patch.msgid.link/20250425192412.1578759-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The phy-upstream enum is already defined in the ethtool.h UAPI header
and used by the ethtool userspace tool. However, the ethtool spec does
not reference it, causing YNL to auto-generate a duplicate and redundant
enum.
Fix this by updating the spec to reference the existing UAPI enum
in ethtool.h.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250425171419.947352-1-kory.maincent@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When removing the clock bits for clocks which aren't used by the
Ethernet driver their names should also have been removed from the
mtk_clks_source_name array.
Remove them now as enum mtk_clks_map needs to match the
mtk_clks_source_name array so the driver can make sure that all required
clocks are present and correctly name missing clocks.
Fixes: 887b1d1adb2e ("net: ethernet: mtk_eth_soc: drop clocks unused by Ethernet driver")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/d075e706ff1cebc07f9ec666736d0b32782fd487.1745555321.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
According to the XGMAC specification, enabling features such as Layer 3
and Layer 4 Packet Filtering, Split Header and Virtualized Network support
automatically selects the IPC Full Checksum Offload Engine on the receive
side.
When RX checksum offload is disabled, these dependent features must also
be disabled to prevent abnormal behavior caused by mismatched feature
dependencies.
Ensure that toggling RX checksum offload (disabling or enabling) properly
disables or enables all dependent features, maintaining consistent and
expected behavior in the network device.
Cc: stable@vger.kernel.org
Fixes: 1a510ccf5869 ("amd-xgbe: Add support for VXLAN offload capabilities")
Signed-off-by: Vishal Badole <Vishal.Badole@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250424130248.428865-1-Vishal.Badole@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mikulas Patocka:
- always update the array size in realloc_argv on success
- dm-integrity: fix a warning on invalid table line
- dm-bufio: don't schedule in atomic context
- Fix W=1 build with clang
* tag 'for-6.15/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: always update the array size in realloc_argv on success
dm-integrity: fix a warning on invalid table line
dm-bufio: don't schedule in atomic context
dm table: Fix W=1 build warning when mempool_needs_integrity is unused
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Madhavan Srinivasan:
- fix to handle patchable function entries during module load
- fix to align vmemmap start to page size
- fixes to handle compilation errors and warnings
Thanks to Anthony Iliopoulos, Donet Tom, Ritesh Harjani (IBM), Venkat
Rao Bagalkote, and Stephen Rothwell.
* tag 'powerpc-6.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/boot: Fix dash warning
powerpc/boot: Check for ld-option support
powerpc: Add check to select PPC_RADIX_BROADCAST_TLBIE
powerpc64/ftrace: fix module loading without patchable function entries
book3s64/radix : Align section vmemmap start address to PAGE_SIZE
book3s64/radix: Fix compile errors when CONFIG_ARCH_WANT_OPTIMIZE_DAX_VMEMMAP=n
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- Bug fixes for the Hyper-V driver and kvp_daemon
* tag 'hyperv-fixes-signed-20250427' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
Drivers: hv: Fix bad ref to hv_synic_eventring_tail when CPU goes offline
tools/hv: update route parsing in kvp daemon
Drivers: hv: Fix bad pointer dereference in hv_get_partition_id
|
|
realloc_argv() was only updating the array size if it was called with
old_argv already allocated. The first time it was called to create an
argv array, it would allocate the array but return the array size as
zero. dm_split_args() would think that it couldn't store any arguments
in the array and would call realloc_argv() again, causing it to
reallocate the initial slots (this time using GPF_KERNEL) and finally
return a size. Aside from being wasteful, this could cause deadlocks on
targets that need to process messages without starting new IO. Instead,
realloc_argv should always update the allocated array size on success.
Fixes: a0651926553c ("dm table: don't copy from a NULL pointer in realloc_argv()")
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI fixes from Bjorn Helgaas:
- When releasing a start-aligned resource, e.g., a bridge window, save
start/end/flags for the next assignment attempt; fixes a v6.15-rc1
regression (Ilpo Järvinen)
- Move set_pcie_speed.sh from TEST_PROGS to TEST_FILE; fixes a bwctrl
selftest v6.15-rc1 regression (Ilpo Järvinen)
- Add Manivannan Sadhasivam as maintainer of native host bridge and
endpoint drivers (Manivannan Sadhasivam)
- In endpoint test driver, defer IRQ allocation from .probe() until
ioctl() to fix a regression on platforms where the Vendor/Device ID
match doesn't include driver_data (Niklas Cassel)
* tag 'pci-v6.15-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
misc: pci_endpoint_test: Defer IRQ allocation until ioctl(PCITEST_SET_IRQTYPE)
MAINTAINERS: Move Manivannan Sadhasivam as PCI Native host bridge and endpoint maintainer
selftests/pcie_bwctrl: Fix test progs list
PCI: Restore assigned resources fully after release
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fix from Chuck Lever:
- Revert a v6.15 patch due to a report of SELinux test failures
* tag 'nfsd-6.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
Revert "sunrpc: clean cache_detail immediately when flush is written frequently"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc x86 fixes from Ingo Molnar:
- Fix 32-bit kernel boot crash if passed physical memory with more than
32 address bits
- Fix Xen PV crash
- Work around build bug in certain limited build environments
- Fix CTEST instruction decoding in insn_decoder_test
* tag 'x86-urgent-2025-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/insn: Fix CTEST instruction decoding
x86/boot: Work around broken busybox 'truncate' tool
x86/mm: Fix _pgd_alloc() for Xen PV mode
x86/e820: Discard high memory that can't be addressed by 32-bit systems
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"Fix sporadic crashes in dequeue_entities() due to ... bad math.
[ Arguably if pick_eevdf()/pick_next_entity() was less trusting of
complex math being correct it could have de-escalated a crash into
a warning, but that's for a different patch ]"
* tag 'sched-urgent-2025-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/eevdf: Fix se->slice being set to U64_MAX and resulting crash
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc perf events fixes from Ingo Molnar:
- Use POLLERR for events in error state, instead of the ambiguous
POLLHUP error value
- Fix non-sampling (counting) events on certain x86 platforms
* tag 'perf-urgent-2025-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Fix non-sampling (counting) events on certain x86 platforms
perf/core: Change to POLLERR for pinned events with error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Ingo Molnar:
"Fix crashes in the gic-v2m irqchip driver, caused by an incorrect
__init annotation"
* tag 'irq-urgent-2025-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v2m: Prevent use after free of gicv2m_get_fwnode()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"Add a missing Kconfig option, fix some bugs in exception handlers,
memory management and KVM"
* tag 'loongarch-fixes-6.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: KVM: Fix PMU pass-through issue if VM exits to host finally
LoongArch: KVM: Fully clear some CSRs when VM reboot
LoongArch: KVM: Fix multiple typos of KVM code
LoongArch: Return NULL from huge_pte_offset() for invalid PMD
LoongArch: Remove a bogus reference to ZONE_DMA
LoongArch: Handle fp, lsx, lasx and lbt assembly symbols
LoongArch: Make do_xyz() exception handlers more robust
LoongArch: Make regs_irqs_disabled() more clear
LoongArch: Select ARCH_USE_MEMTEST
|
|
Pull OpenRISC updates from Stafford Horne:
- Support for cacheinfo API to expose OpenRISC cache info via sysfs,
this also translated to some cleanups to OpenRISC cache flush and
invalidate API's
- Documentation updates for new mailing list and toolchain binaries
* tag 'for-linus' of https://github.com/openrisc/linux:
Documentation: openrisc: Update toolchain binaries URL
Documentation: openrisc: Update mailing list
openrisc: Add cacheinfo support
openrisc: Introduce new utility functions to flush and invalidate caches
openrisc: Refactor struct cpuinfo_or1k to reduce duplication
|
|
Ondrej reports that certain SELinux tests are failing after commit
fc2a169c56de ("sunrpc: clean cache_detail immediately when flush is
written frequently"), merged during the v6.15 merge window.
Reported-by: Ondrej Mosnacek <omosnace@redhat.com>
Fixes: fc2a169c56de ("sunrpc: clean cache_detail immediately when flush is written frequently")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull kunit fix from Kees Cook:
"A single fix for the kunit lib/tests/ relocation:
- Ensure prime numbers tests are included in KUnit test runs (Mark Brown)"
* tag 'move-lib-kunit-v6.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
lib: Ensure prime numbers tests are included in KUnit test runs
|
|
Pull drm fixes from Dave Airlie:
"Weekly drm fixes, mostly amdgpu, with some exynos cleanups and a
couple of minor fixes, seems a bit quiet, but probably some lag from
Easter holidays.
amdgpu:
- P2P DMA fixes
- Display reset fixes
- DCN 3.5 fixes
- ACPI EDID fix
- LTTPR fix
- mode_valid() fix
exynos:
- fix spelling error
- remove redundant error handling in exynos_drm_vidi.c module
- marks struct decon_data as const in the exynos7_drm_decon driver
since it is only read
- Remove unnecessary checking in exynos_drm_drv.c module
meson:
- Fix VCLK calculation
panel:
- jd9365a: Fix reset polarity"
* tag 'drm-fixes-2025-04-26' of https://gitlab.freedesktop.org/drm/kernel:
drm/exynos: Fix spelling mistake "enqueu" -> "enqueue"
drm/exynos: exynos7_drm_decon: Consstify struct decon_data
drm/exynos: fixed a spelling error
drm/exynos/vidi: Remove redundant error handling in vidi_get_modes()
drm/exynos: Remove unnecessary checking
drm/amd/display: do not copy invalid CRTC timing info
drm/amd/display: Default IPS to RCG_IN_ACTIVE_IPS2_IN_OFF
drm/amd/display: Use 16ms AUX read interval for LTTPR with old sinks
drm/amd/display: Fix ACPI edid parsing on some Lenovo systems
drm/amdgpu: Allow P2P access through XGMI
drm/amd/display: Enable urgent latency adjustment on DCN35
drm/amd/display: Force full update in gpu reset
drm/amd/display: Fix gpu reset in multidisplay config
drm/amdgpu: Don't pin VRAM without DMABUF_MOVE_NOTIFY
drm/amdgpu: Use allowed_domains for pinning dmabufs
drm: panel: jd9365da: fix reset signal polarity in unprepare
drm/meson: use unsigned long long / Hz for frequency types
Revert "drm/meson: vclk: fix calculation of 59.94 fractional rates"
|
|
There is a code path in dequeue_entities() that can set the slice of a
sched_entity to U64_MAX, which sometimes results in a crash.
The offending case is when dequeue_entities() is called to dequeue a
delayed group entity, and then the entity's parent's dequeue is delayed.
In that case:
1. In the if (entity_is_task(se)) else block at the beginning of
dequeue_entities(), slice is set to
cfs_rq_min_slice(group_cfs_rq(se)). If the entity was delayed, then
it has no queued tasks, so cfs_rq_min_slice() returns U64_MAX.
2. The first for_each_sched_entity() loop dequeues the entity.
3. If the entity was its parent's only child, then the next iteration
tries to dequeue the parent.
4. If the parent's dequeue needs to be delayed, then it breaks from the
first for_each_sched_entity() loop _without updating slice_.
5. The second for_each_sched_entity() loop sets the parent's ->slice to
the saved slice, which is still U64_MAX.
This throws off subsequent calculations with potentially catastrophic
results. A manifestation we saw in production was:
6. In update_entity_lag(), se->slice is used to calculate limit, which
ends up as a huge negative number.
7. limit is used in se->vlag = clamp(vlag, -limit, limit). Because limit
is negative, vlag > limit, so se->vlag is set to the same huge
negative number.
8. In place_entity(), se->vlag is scaled, which overflows and results in
another huge (positive or negative) number.
9. The adjusted lag is subtracted from se->vruntime, which increases or
decreases se->vruntime by a huge number.
10. pick_eevdf() calls entity_eligible()/vruntime_eligible(), which
incorrectly returns false because the vruntime is so far from the
other vruntimes on the queue, causing the
(vruntime - cfs_rq->min_vruntime) * load calulation to overflow.
11. Nothing appears to be eligible, so pick_eevdf() returns NULL.
12. pick_next_entity() tries to dereference the return value of
pick_eevdf() and crashes.
Dumping the cfs_rq states from the core dumps with drgn showed tell-tale
huge vruntime ranges and bogus vlag values, and I also traced se->slice
being set to U64_MAX on live systems (which was usually "benign" since
the rest of the runqueue needed to be in a particular state to crash).
Fix it in dequeue_entities() by always setting slice from the first
non-empty cfs_rq.
Fixes: aef6987d8954 ("sched/eevdf: Propagate min_slice up the cgroup hierarchy")
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/f0c2d1072be229e1bdddc73c0703919a8b00c652.1745570998.git.osandov@fb.com
|
|
With ACPI in place, gicv2m_get_fwnode() is registered with the pci
subsystem as pci_msi_get_fwnode_cb(), which may get invoked at runtime
during a PCI host bridge probe. But, the call back is wrongly marked as
__init, causing it to be freed, while being registered with the PCI
subsystem and could trigger:
Unable to handle kernel paging request at virtual address ffff8000816c0400
gicv2m_get_fwnode+0x0/0x58 (P)
pci_set_bus_msi_domain+0x74/0x88
pci_register_host_bridge+0x194/0x548
This is easily reproducible on a Juno board with ACPI boot.
Retain the function for later use.
Fixes: 0644b3daca28 ("irqchip/gic-v2m: acpi: Introducing GICv2m ACPI support")
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
|
|
Louis-Alexis Eyraud says:
====================
net: ethernet: mtk-star-emac: fix several issues on rx/tx poll
This patchset fixes two issues with the mtk-star-emac driver.
The first patch fixes spin lock recursion issues I've observed on the
Mediatek Genio 350-EVK board using this driver when the Ethernet
functionality is enabled on the board (requires a correct jumper and
DIP switch configuration, as well as enabling the device in the
devicetree).
The issues can be easily reproduced with apt install or ssh commands
especially and with the CONFIG_DEBUG_SPINLOCK parameter, when
one occurs, there is backtrace similar to this:
```
BUG: spinlock recursion on CPU#0, swapper/0/0
lock: 0xffff00000db9cf20, .magic: dead4ead, .owner: swapper/0/0,
.owner_cpu: 0
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted
6.15.0-rc2-next-20250417-00001-gf6a27738686c-dirty #28 PREEMPT
Hardware name: MediaTek MT8365 Open Platform EVK (DT)
Call trace:
show_stack+0x18/0x24 (C)
dump_stack_lvl+0x60/0x80
dump_stack+0x18/0x24
spin_dump+0x78/0x88
do_raw_spin_lock+0x11c/0x120
_raw_spin_lock+0x20/0x2c
mtk_star_handle_irq+0xc0/0x22c [mtk_star_emac]
__handle_irq_event_percpu+0x48/0x140
handle_irq_event+0x4c/0xb0
handle_fasteoi_irq+0xa0/0x1bc
handle_irq_desc+0x34/0x58
generic_handle_domain_irq+0x1c/0x28
gic_handle_irq+0x4c/0x120
do_interrupt_handler+0x50/0x84
el1_interrupt+0x34/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
regmap_mmio_read32le+0xc/0x20 (P)
_regmap_bus_reg_read+0x6c/0xac
_regmap_read+0x60/0xdc
regmap_read+0x4c/0x80
mtk_star_rx_poll+0x2f4/0x39c [mtk_star_emac]
__napi_poll+0x38/0x188
net_rx_action+0x164/0x2c0
handle_softirqs+0x100/0x244
__do_softirq+0x14/0x20
____do_softirq+0x10/0x20
call_on_irq_stack+0x24/0x64
do_softirq_own_stack+0x1c/0x40
__irq_exit_rcu+0xd4/0x10c
irq_exit_rcu+0x10/0x1c
el1_interrupt+0x38/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
cpuidle_enter_state+0xac/0x320 (P)
cpuidle_enter+0x38/0x50
do_idle+0x1e4/0x260
cpu_startup_entry+0x34/0x3c
rest_init+0xdc/0xe0
console_on_rootfs+0x0/0x6c
__primary_switched+0x88/0x90
```
The second patch is a cleanup patch to fix a inconsistency in the
mtk_star_rx_poll function between the napi_complete_done api usage and
its description in documentation.
I've tested this patchset on Mediatek Genio 350-EVK board with a kernel
based on linux-next (tag: next-20250422).
v1: https://lore.kernel.org/20250422-mtk_star_emac-fix-spinlock-recursion-issue-v1-0-1e94ea430360@collabora.com
====================
Link: https://patch.msgid.link/20250424-mtk_star_emac-fix-spinlock-recursion-issue-v2-0-f3fde2e529d8@collabora.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In mtk_star_rx_poll function, on event processing completion, the
mtk_star_emac driver calls napi_complete_done but ignores its return
code and enable RX DMA interrupts inconditionally. This return code
gives the info if a device should avoid rearming its interrupts or not,
so fix this behaviour by taking it into account.
Fixes: 8c7bd5a454ff ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20250424-mtk_star_emac-fix-spinlock-recursion-issue-v2-2-f3fde2e529d8@collabora.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use spin_lock_irqsave and spin_unlock_irqrestore instead of spin_lock
and spin_unlock in mtk_star_emac driver to avoid spinlock recursion
occurrence that can happen when enabling the DMA interrupts again in
rx/tx poll.
```
BUG: spinlock recursion on CPU#0, swapper/0/0
lock: 0xffff00000db9cf20, .magic: dead4ead, .owner: swapper/0/0,
.owner_cpu: 0
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted
6.15.0-rc2-next-20250417-00001-gf6a27738686c-dirty #28 PREEMPT
Hardware name: MediaTek MT8365 Open Platform EVK (DT)
Call trace:
show_stack+0x18/0x24 (C)
dump_stack_lvl+0x60/0x80
dump_stack+0x18/0x24
spin_dump+0x78/0x88
do_raw_spin_lock+0x11c/0x120
_raw_spin_lock+0x20/0x2c
mtk_star_handle_irq+0xc0/0x22c [mtk_star_emac]
__handle_irq_event_percpu+0x48/0x140
handle_irq_event+0x4c/0xb0
handle_fasteoi_irq+0xa0/0x1bc
handle_irq_desc+0x34/0x58
generic_handle_domain_irq+0x1c/0x28
gic_handle_irq+0x4c/0x120
do_interrupt_handler+0x50/0x84
el1_interrupt+0x34/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
regmap_mmio_read32le+0xc/0x20 (P)
_regmap_bus_reg_read+0x6c/0xac
_regmap_read+0x60/0xdc
regmap_read+0x4c/0x80
mtk_star_rx_poll+0x2f4/0x39c [mtk_star_emac]
__napi_poll+0x38/0x188
net_rx_action+0x164/0x2c0
handle_softirqs+0x100/0x244
__do_softirq+0x14/0x20
____do_softirq+0x10/0x20
call_on_irq_stack+0x24/0x64
do_softirq_own_stack+0x1c/0x40
__irq_exit_rcu+0xd4/0x10c
irq_exit_rcu+0x10/0x1c
el1_interrupt+0x38/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
cpuidle_enter_state+0xac/0x320 (P)
cpuidle_enter+0x38/0x50
do_idle+0x1e4/0x260
cpu_startup_entry+0x34/0x3c
rest_init+0xdc/0xe0
console_on_rootfs+0x0/0x6c
__primary_switched+0x88/0x90
```
Fixes: 0a8bd81fd6aa ("net: ethernet: mtk-star-emac: separate tx/rx handling with two NAPIs")
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20250424-mtk_star_emac-fix-spinlock-recursion-issue-v2-1-f3fde2e529d8@collabora.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
rtase_calc_time_mitigation
Fix the following compile error reported by the kernel test
robot by modifying the condition used to detect overflow in
rtase_calc_time_mitigation.
In file included from include/linux/mdio.h:10:0,
from drivers/net/ethernet/realtek/rtase/rtase_main.c:58:
In function 'u16_encode_bits',
inlined from 'rtase_calc_time_mitigation.constprop' at drivers/net/
ethernet/realtek/rtase/rtase_main.c:1915:13,
inlined from 'rtase_init_software_variable.isra.41' at drivers/net/
ethernet/realtek/rtase/rtase_main.c:1961:13,
inlined from 'rtase_init_one' at drivers/net/ethernet/realtek/
rtase/rtase_main.c:2111:2:
>> include/linux/bitfield.h:178:3: error: call to '__field_overflow'
declared with attribute error: value doesn't fit into mask
__field_overflow(); \
^~~~~~~~~~~~~~~~~~
include/linux/bitfield.h:198:2: note: in expansion of macro
'____MAKE_OP'
____MAKE_OP(u##size,u##size,,)
^~~~~~~~~~~
include/linux/bitfield.h:200:1: note: in expansion of macro
'__MAKE_OP'
__MAKE_OP(16)
^~~~~~~~~
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202503182158.nkAlbJWX-lkp@intel.com/
Fixes: a36e9f5cfe9e ("rtase: Add support for a pci table in this module")
Signed-off-by: Justin Lai <justinlai0215@realtek.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250424040444.5530-1-justinlai0215@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In function kvm_pre_enter_guest(), it prepares to enter guest and check
whether there are pending signals or events. And it will not enter guest
if there are, PMU pass-through preparation for guest should be cancelled
and host should own PMU hardware.
Cc: stable@vger.kernel.org
Fixes: f4e40ea9f78f ("LoongArch: KVM: Add PMU support for guest")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
