summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-03-16ARM: ux500: Enable PL011 AMBA UART Controller for Device TreeLee Jones
Enables the 3 UARTs found on a u8500 using DT. Acked-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-03-16ARM: ux500: Enable Cortex-A9 GIC (Generic Interrupt Controller) in Device TreeLee Jones
This enables the embedded GIC on all u8500 based hardware using DT. Acked-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-03-16ARM: ux500: db8500: list most devices in the snowball device treeLee Jones
This adds all devices that are normally present through the u8500_init_machine function in the device tree as well, which will duplicate the devices that are visible. This will not do much by itself because the device from the device tree are not matched by any device driver until they are converted as well. The next step is to move over one device at a time to actually be used from the device tree instead of the hardcoded device using auxdata to pass the correct platform_data. Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-03-16ARM: ux500: split dts file for snowball into generic partArnd Bergmann
db8500.dtsi can be used by all systems with a db8500 or db9500 SoC, while snowball.dts is board specific. Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-03-16ARM: ux500: combine the board init functions for DT bootArnd Bergmann
This lets us move over evertything to device tree one by one. Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-03-16ARM: ux500: Initial Device Tree support for SnowballArnd Bergmann
This provides very basic Device Tree support for ST-Ericsson's low-cost development platform, Snowball. If Device Tree for ux500 is enabled and the correct board is configured within the Device Tree blob, the correct *_init_machine() will be called. This patch is based on some original work completed by: Niklas Hernaeus <niklas.hernaeus@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Niklas Hernaeus <niklas.hernaeus@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-03-16ARM: ux500: CONFIG: Enable Device Tree support for future endeavoursLee Jones
Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-03-16mfd: Use DIV_ROUND_CLOSEST for sm501 clockAxel Lin
Use DIV_ROUND_CLOSEST to replace sm501fb_round_div function. Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-03-16powerpc/83xx: mpc836x - fix failed phy detection for ucc ethernet on MDSPaul Gortmaker
The mpc836x_mds platform has been broken since the commit 6fe3264945ee63292cdfb27b6e95bc52c603bb09 "netdev/phy: Use mdiobus_read() so that proper locks are taken" which caused the fsl_pq_mdio TBI autoprobe to oops. The oops was "fixed" in commit 28d8ea2d568534026ccda3e8936f5ea1e04a86a1 "fsl_pq_mdio: Clean up tbi address configuration" by simply removing the the autoscan code, and making tbi nodes mandatory. Some of the newer reference platforms were updated to have tbi nodes in 220669495bf8b68130a8218607147c7b74c28d2b "powerpc: Add TBI PHY node to first MDIO bus" but the older mpc836x didn't get one and hence was just failing with -EBUSY as follows: fsl-pq_mdio: probe of e0102120.mdio failed with error -16 ... net eth0: Could not attach to PHY eth0: Cannot initialize PHY, aborting. Add a TBI node and use the 1st free address for it. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16regulator: Fix up a confusing dev_warn when DT lookup failsRajendra Nayak
of_parse_phandle() returns NULL either if the property name itself does not exist or if it (exists and) does not reference a valid phandle. Giving out a warn like the one below (that the property references an invalid phandle) can be confusing when the property itself does not exist in the node. Fix it with a more sensible message and make it a dev_dbg instead of a dev_warn. Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-03-16Merge branch 'depends/driver-core' into ux500/dtArnd Bergmann
Conflicts: drivers/base/cpu.c
2012-03-16Merge branch 'ux500/soc' into ux500/dtArnd Bergmann
2012-03-16mfd: Add support for RICOH PMIC RC5T583Laxman Dewangan
Ricoh power management IC RC5T583 contains is multi functional device having multiple sub devices inside this. This device has multiple dcdc/ldo regulators, gpios, interrupt controllers, on-key, RTCs, ADCs. This device have 4 DCDCs, 8 LDOs, 8 GPIOs, 6 ADCs, 3 RTCs etc. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-03-16ASoC: Samsung: Added to support mono recordingSangsu Park
The dma size will be changed by requested number of channel(mono/stereo) from platform. For mono recording, channels_min value should be 1. Signed-off-by: Sangsu Park <sangsu4u.park@samsung.com> Signed-off-by: Sangbeom Kim <sbkim73@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-03-16mfd: Make use of the ab8500 firmware read-modify-write serviceMattias Nilsson
This patch updates the AB8500 driver to make use of the I2C read-modify-write service in the PRCMU firmware. Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com> Reviewed-by: Mattias Wallin <mattias.wallin@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-03-16mfd: Add a prcmu_abb_write_masked routine to db8500-prcmuMattias Nilsson
This patch adds driver support for the I2C read-modify-write service in the U8500 PRCMU firmware. Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com> Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-03-16mfd: Support for the AB8500 AB8505 variantBengt Jonsson
This builds upon the changes done to support AB9540 so as also to support the AB8505 derivative of the AB8500 circuit. Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-03-16mfd: Don't use mutex_lock_interruptible in ab8500-coreRabin Vincent
This disadvantage of having it interruptible is that it would appear to work OK in most situations, but in the rare case that this call does fail, it can lead to misconfiguration of the AB, such as a regulator not being turned off and leading to a platform power consumption increase. There's no real benefit to having this interruptible. Make it a plain mutex_lock. The non-interruptability matches other low-level I/O functions such as SPI and I2C. Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-03-16ARM: S3C64XX: Hook up supply for WM8994 LDOs on LittlemillMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-03-16mfd: Remove unused LDO supply field from WM8994 pdataMark Brown
It's causing confusion with the regulator level field of the same name and serves no useful function. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-03-16mfd: Use correct variable name for tps65910 regmap configLaxman Dewangan
This was the copy-paste issue in reg cache support code where variable name for regmap config was not really starting from the device name, it was starting from some other device name. Fixing this so that variable name contains actual device name. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-03-16Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem Conflicts: drivers/net/wireless/ath/ath9k/hw.c
2012-03-16mfd: Add platform data for MAX8997 haptic driverChanwoo Choi
MAX8997 device does not support haptic function of it. This patch adds platform data for for MAX8997 haptic driver. Signed-off-by: Donggeun Kim <dg77.kim@samsung.com> Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-03-16mfd: wm8994: Fix register default for WM1811 AntiPOP2Mark Brown
Should be all bits clear. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-03-16mfd: wm8994: Remove defaults for volatile registersMark Brown
Some volatile registers accidentally had defaults added, though there were no harmful side effects other than increased memory consumption. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-03-16powerpc/85xx: p1022ds: enable monitor switching via pixis indirect modeTimur Tabi
When the P1022's DIU video controller is active, the pixis must be accessed in "indirect" mode, which uses localbus chip select addresses. Switching between the DVI and LVDS monitor ports is handled by the pixis, so that switching needs to be done via indirect mode. This has the side-effect of no longer requiring U-Boot to enable the DIU. Now Linux can enable the DIU all by itself. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/85xx: Board support for GE IMP3AMartyn Welch
Initial board support for the GE IMP3A, a 3U compactPCI card with a p2020 processor. Signed-off-by: Martyn Welch <martyn.welch@ge.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc: Move GE PIC driversMartyn Welch
Move the GE PIC drivers to allow these to be used by non-86xx boards. Signed-off-by: Martyn Welch <martyn.welch@ge.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16gpio: Move GE GPIO driver to reside within GPIO subsystemMartyn Welch
The GE GPIO driver provides basic support (set direction, read/write state) for the GPIO provided on some GE single board computers. This patch moves the driver from the 86xx specific platform directrory to the GPIO subsystem so that it can be used on non-86xx boards. Signed-off-by: Martyn Welch <martyn.welch@ge.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc: Add GE FPGA config optionMartyn Welch
This patch adds the GE_FPGA configuration option. This is being carried out as ground work to allow the PIC and GPIO drivers to be move from the powerpc 86xx platform directory to more general locations to allow them to be used on non-86xx boards and to reduce churn when further boards using these drivers are added. Signed-off-by: Martyn Welch <martyn.welch@ge.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/85xx: Add dts for p1020rdb-pc boardZhicheng Fan
P1020RDB-PC Overview ------------------ 1Gbyte DDR3 SDRAM 32 Mbyte NAND flash 10 16Mbyte NOR flash 16 Mbyte SPI flash SD connector to interface with the SD memory card Real-time clock on I2C bus PCIe: - x1 PCIe slot - x1 mini-PCIe slot 10/100/1000 BaseT Ethernet ports: - eTSEC1, RGMII: one 10/100/1000 port using VitesseTM VSC7385 L2 switch - eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221 - eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021 USB 2.0 port: - Two USB2.0 Type A receptacles - One USB2.0 signal to Mini PCIe slot Dual RJ45 UART ports: - DUART interface: supports two UARTs up to 115200 bps for console display Signed-off-by: Zhicheng Fan <b32736@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/85xx: Add p1020rdb-pc platform supportZhicheng Fan
Signed-off-by: Zhicheng Fan <b32736@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/85xx: add P1020UTM-PC platform supportJerry Huang
The p1020utm-pc has the similar feature as the p1020rdb. Therefore, p1020utm-pc use the same platform file as the p1/p2 rdb board. Overview of P1020UTM-PC platform: - DDR3 1GB - NOR flash 32MB - I2C EEPROM 256Kb - eTSEC1 (RGMII PHY Atheros AR8021) - eTSEC2 (SGMII PHY Vitesse VSC8221) - eTSEC3 (RGMII PHY Atheros AR8021) - SDHC - 2 USB ports - PCIe (Lane1 to dual SATA controller) Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/85xx: add P1020MBG-PC platform supportJerry Huang
The p1020mbg-pc has the similar feature as the p1020rdb. Therefore, p1020mbg-pc use the same platform file as the p1/p2 rdb board. Overview of P1020MBG-PC platform: - DDR3 2GB - NOR flash 64MB - I2C EEPROM 256Kb - eTSEC1 (RGMII PHY) connected to VSC7385 L2 switch - eTSEC2 (SGMII PHY) - eTSEC3 (RGMII PHY) - SDHC - 2 USB ports - 4 TDM ports - PCIe (Lane1 to dual SATA controller) Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16NAND Machine support for Integrated Flash ControllerPrabhakar Kushwaha
Integrated Flash Controller(IFC) can be used to hook NAND Flash chips using NAND Flash Machine available on it. Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Liu Shuo <b35362@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/85xx: Clean up partition nodes in dts for MPC8572DSJia Hongtao
Signed-off-by: Jin Qing <b24347@freescale.com> Signed-off-by: Jia Hongtao <B38951@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/85xx: p1022ds: disable the NOR flash node if video is enabledTimur Tabi
The Freescale P1022 has a unique pin muxing "feature" where the DIU video controller's video signals are muxed with 24 of the local bus address signals. When the DIU is enabled, the bulk of the local bus is disabled, preventing access to memory-mapped devices like NOR flash and the pixis FPGA. Therefore, if the DIU is going to be enabled, then memory-mapped devices on the localbus, like NOR flash, need to be disabled. This also means that the localbus is not a 'simple-bus' any more, so remove that string from the compatible node. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/85xx: create 32-bit DTS for the P1022DSTimur Tabi
Create a 32-bit address space version of p1022ds.dts. To avoid confusion, p1022ds.dts is renamed to p1022ds_36b.dts. We also create p1022ds.dtsi to store some common nodes. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/85xx: Add magic-packet properties for etsecXie Xiaobo
The properties indicates that the hardware supports waking up via magic packet. Signed-off-by: Xie Xiaobo <X.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/85xx: Add some DTS nodes and attributes for mpc8536dsXie Xiaobo
Add partitions for NOR and NAND Flash. Signed-off-by: Xie Xiaobo <X.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/fsl_msi: return proper error value when ioremap failed.Liu Shuo
Signed-off-by: Liu Shuo <soniccat.liu@gmail.com> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/85xx: fix typo in p1010rdb.dtsiGustavo Zacarias
Fix typo introduced by "powerpc: Add TBI PHY node to first MDIO bus" from Andy Fleming. It's device_type rather than device-type, which causes the mdio probe to fail thus making all gianfar ethernet interfaces unusable. Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/85xx: p2020rdb & p1010rdb - lower spi flash freq to 40MhzSebastian Andrzej Siewior
This is here most likely since the FSL bsp. Back in the FSL bsp it was set to 50Mhz and working. However the driver divided the SoC freq. only by 2. According to the TRM the platform clock (which the manual refers in its formula) is the system clock divided by two. So in the end it has to divide by 4 and this is what the fsl-spi driver in tree is doing. Since then the flash is not wokring I guess. After chaning the freq from 50Mhz to 40Mhz like others do then I can access the flash. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/85xx: p2020rdb - move the NAND address.Sebastian Andrzej Siewior
It is not at 0xffa00000. According to current u-boot source the NAND controller is always at 0xff800000 and it is either at CS0 or CS1 depending on NAND or NAND+NOR mode. In 36bit mode it is shifted to 0xfff800000 but it has always an eight there and never an A. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/srio: Fix the compile errors when building with 64bitLiu Gang
For the file "arch/powerpc/sysdev/fsl_rmu.c", there will be some compile errors while using the corenet64_smp_defconfig: .../fsl_rmu.c:315: error: cast from pointer to integer of different size .../fsl_rmu.c:320: error: cast to pointer from integer of different size .../fsl_rmu.c:320: error: cast to pointer from integer of different size .../fsl_rmu.c:320: error: cast to pointer from integer of different size .../fsl_rmu.c:330: error: cast to pointer from integer of different size .../fsl_rmu.c:332: error: cast to pointer from integer of different size .../fsl_rmu.c:339: error: cast to pointer from integer of different size .../fsl_rmu.c:340: error: cast to pointer from integer of different size .../fsl_rmu.c:341: error: cast to pointer from integer of different size .../fsl_rmu.c:348: error: cast to pointer from integer of different size .../fsl_rmu.c:348: error: cast to pointer from integer of different size .../fsl_rmu.c:348: error: cast to pointer from integer of different size .../fsl_rmu.c:659: error: cast from pointer to integer of different size .../fsl_rmu.c:659: error: format '%8.8x' expects type 'unsigned int', but argument 5 has type 'size_t' .../fsl_rmu.c:985: error: cast from pointer to integer of different size .../fsl_rmu.c:997: error: cast to pointer from integer of different size Rewrote the corresponding code with the support of 64bit building. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/srio: Fix the relocation errors when building with 64bitLiu Gang
For the file "arch/powerpc/sysdev/fsl_rio.c", there will be some relocation errors while using the corenet64_smp_defconfig: WARNING: modpost: Found 6 section mismatch(es). To see full details build your kernel with: 'make CONFIG_DEBUG_SECTION_MISMATCH=y' GEN .version CHK include/generated/compile.h UPD include/generated/compile.h CC init/version.o LD init/built-in.o LD .tmp_vmlinux1 arch/powerpc/sysdev/built-in.o:(__ex_table+0x0): relocation truncated to fit: R_PPC64_ADDR16 against `.text'+3208 arch/powerpc/sysdev/built-in.o:(__ex_table+0x2): relocation truncated to fit: R_PPC64_ADDR16 against `.fixup' arch/powerpc/sysdev/built-in.o:(__ex_table+0x4): relocation truncated to fit: R_PPC64_ADDR16 against `.text'+3230 arch/powerpc/sysdev/built-in.o:(__ex_table+0x6): relocation truncated to fit: R_PPC64_ADDR16 against `.fixup'+c arch/powerpc/sysdev/built-in.o:(__ex_table+0x8): relocation truncated to fit: R_PPC64_ADDR16 against `.text'+3250 arch/powerpc/sysdev/built-in.o:(__ex_table+0xa): relocation truncated to fit: R_PPC64_ADDR16 against `.fixup'+18 Rewrote the corresponding code with the support of 64bit building. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/85xx: Add dts for p1025rdb boardZhicheng Fan
P1025RDB Overview ------------------ 1Gbyte DDR3 SDRAM 32 Mbyte NAND flash 16Mbyte NOR flash 16 Mbyte SPI flash SD connector to interface with the SD memory card Real-time clock on I2C bus PCIe: - x1 PCIe slot - x1 mini-PCIe slot 10/100/1000 BaseT Ethernet ports: - eTSEC1, RGMII: one 10/100/1000 port using AtherosTM AR8021 - eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221 - eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021 USB 2.0 port: - Two USB2.0 Type A receptacles - One USB2.0 signal to Mini PCIe slot Dual RJ45 UART ports: - DUART interface: supports two UARTs up to 115200 bps for console display Signed-off-by: Zhicheng Fan <b32736@freescale.com> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/85xx: Add p1025rdb platform supportZhicheng Fan
Signed-off-by: Zhicheng Fan <b32736@freescale.com> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/85xx: Add usb controller version infoRamneek Mehresh
Add usb controller version info for the following: MPC8536, P1010, P1020, P1021, P1022, P1023, P2020, P2041, P3041, P3060, P5020 Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-03-16powerpc/85xx: Add p2020rdb-pc dts supportTang Yuantian
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Tang Yuantian <b29983@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit (git 2.34.1) at 2025-09-22 21:24:40 +0000