| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some Kconfig dependency fixes"
* tag 'media/v6.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: cec: tda9950: add back i2c dependency
media: i2c: lt6911uxe: add two selects to Kconfig
media: platform: synopsys: VIDEO_SYNOPSYS_HDMIRX should depend on ARCH_ROCKCHIP
media: i2c: lt6911uxe: Fix Kconfig dependencies:
media: vivid: fix FB dependency
|
|
Multishot normally uses io_req_post_cqe() to post completions, but when
stopping it, it may finish up with a deferred completion. This is fine,
except if another multishot event triggers before the deferred completions
get flushed. If this occurs, then CQEs may get reordered in the CQ ring,
as new multishot completions get posted before the deferred ones are
flushed. This can cause confusion on the application side, if strict
ordering is required for the use case.
When multishot posting via io_req_post_cqe(), flush any pending deferred
completions first, if any.
Cc: stable@vger.kernel.org # 6.1+
Reported-by: Norman Maurer <norman_maurer@apple.com>
Reported-by: Christian Mazakas <christian.mazakas@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Xen swiotlb support was missed when the patch set starting with
4ab5f8ec7d71 ("mm/slab: decouple ARCH_KMALLOC_MINALIGN from
ARCH_DMA_MINALIGN") was merged.
When running Xen on iMX8QXP, a SoC without IOMMU, the effect was that USB
transfers ended up corrupted when there was more than one URB inflight at
the same time.
Add a call to dma_kmalloc_needs_bounce() to make sure that allocations too
small for DMA get bounced via swiotlb.
Closes: https://lore.kernel.org/linux-usb/ab2776f0-b838-4cf6-a12a-c208eb6aad59@actia.se/
Fixes: 4ab5f8ec7d71 ("mm/slab: decouple ARCH_KMALLOC_MINALIGN from ARCH_DMA_MINALIGN")
Cc: stable@kernel.org # v6.5+
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Message-ID: <20250502114043.1968976-2-john.ernberg@actia.se>
|
|
The wlan_ctrl_by_user detection was introduced by commit a50bd128f28c
("asus-wmi: record wlan status while controlled by userapp").
Quoting from that commit's commit message:
"""
When you call WMIMethod(DSTS, 0x00010011) to get WLAN status, it may return
(1) 0x00050001 (On)
(2) 0x00050000 (Off)
(3) 0x00030001 (On)
(4) 0x00030000 (Off)
(5) 0x00000002 (Unknown)
(1), (2) means that the model has hardware GPIO for WLAN, you can call
WMIMethod(DEVS, 0x00010011, 1 or 0) to turn WLAN on/off.
(3), (4) means that the model doesn’t have hardware GPIO, you need to use
API or driver library to turn WLAN on/off, and call
WMIMethod(DEVS, 0x00010012, 1 or 0) to set WLAN LED status.
After you set WLAN LED status, you can see the WLAN status is changed with
WMIMethod(DSTS, 0x00010011). Because the status is recorded lastly
(ex: Windows), you can use it for synchronization.
(5) means that the model doesn’t have WLAN device.
WLAN is the ONLY special case with upper rule.
"""
The wlan_ctrl_by_user flag should be set on 0x0003000? ((3), (4) above)
return values, but the flag mistakenly also gets set on laptops with
0x0005000? ((1), (2)) return values. This is causing rfkill problems on
laptops where 0x0005000? is returned.
Fix the check to only set the wlan_ctrl_by_user flag for 0x0003000?
return values.
Fixes: a50bd128f28c ("asus-wmi: record wlan status while controlled by userapp")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219786
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20250501131702.103360-2-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
(GX4HRXL)
MECHREVO Wujie 14XA (GX4HRXL) wakes up immediately after s2idle entry.
This happens regardless of whether the laptop is plugged into AC power,
or whether any peripheral is plugged into the laptop.
Similar to commit a55bdad5dfd1 ("platform/x86/amd/pmc: Disable keyboard
wakeup on AMD Framework 13"), the MECHREVO Wujie 14XA wakes up almost
instantly after s2idle suspend entry (IRQ1 is the keyboard):
2025-04-18 17:23:57,588 DEBUG: PM: Triggering wakeup from IRQ 9
2025-04-18 17:23:57,588 DEBUG: PM: Triggering wakeup from IRQ 1
Add this model to the spurious_8042 quirk to workaround this.
This patch does not affect the wake-up function of the built-in keyboard.
Because the firmware of this machine adds an insurance for keyboard
wake-up events, as it always triggers an additional IRQ 9 to wake up the
system.
Suggested-by: Mingcong Bai <jeffbai@aosc.io>
Suggested-by: Xinhui Yang <cyan@cyano.uk>
Suggested-by: Rong Zhang <i@rong.moe>
Fixes: a55bdad5dfd1 ("platform/x86/amd/pmc: Disable keyboard wakeup on AMD Framework 13")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4166
Cc: Mario Limonciello <mario.limonciello@amd.com>
Link: https://zhuanldan.zhihu.com/p/730538041
Tested-by: Yemu Lu <prcups@krgm.moe>
Signed-off-by: Runhua He <hua@aosc.io>
Link: https://lore.kernel.org/r/20250507100103.995395-1-hua@aosc.io
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Change get_thinkpad_model_data() to check for additional vendor name
"NEC" in order to support NEC Lavie X1475JAS notebook (and perhaps
more).
The reason of this works with minimal changes is because NEC Lavie
X1475JAS is a Thinkpad inside. ACPI dumps reveals its OEM ID to be
"LENOVO", BIOS version "R2PET30W" matches typical Lenovo BIOS version,
the existence of HKEY of LEN0268, with DMI fw string is "R2PHT24W".
I compiled and tested with my own machine, attached the dmesg
below as proof of work:
[ 6.288932] thinkpad_acpi: ThinkPad ACPI Extras v0.26
[ 6.288937] thinkpad_acpi: http://ibm-acpi.sf.net/
[ 6.288938] thinkpad_acpi: ThinkPad BIOS R2PET30W (1.11 ), EC R2PHT24W
[ 6.307000] thinkpad_acpi: radio switch found; radios are enabled
[ 6.307030] thinkpad_acpi: This ThinkPad has standard ACPI backlight brightness control, supported by the ACPI video driver
[ 6.307033] thinkpad_acpi: Disabling thinkpad-acpi brightness events by default...
[ 6.320322] thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is unblocked
[ 6.371963] thinkpad_acpi: secondary fan control detected & enabled
[ 6.391922] thinkpad_acpi: battery 1 registered (start 0, stop 85, behaviours: 0x7)
[ 6.398375] input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input13
Signed-off-by: John Chau <johnchau@0atlas.com>
Link: https://lore.kernel.org/r/20250504165513.295135-1-johnchau@0atlas.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Oleksij Rempel says:
====================
lan78xx: preparation for PHYLINK conversion
This patch series contains the first part of the LAN78xx driver
refactoring in preparation for converting the driver to use the PHYLINK
framework.
The goal of this initial part is to reduce the size and complexity of
the final PHYLINK conversion by introducing incremental cleanups and
logical separation of concerns, such as:
- Improving error handling in the PHY initialization path
- Refactoring PHY detection and MAC-side configuration
- Moving LED DT configuration to a dedicated helper
- Separating USB link power and flow control setup from the main probe logic
- Extracting PHY interrupt acknowledgment logic
Each patch is self-contained and moves non-PHYLINK-specific logic out of
the way, setting the stage for the actual conversion in a follow-up
patch series.
changes v8 (as split from full v7 00/12 series):
- Split the original series to make review easier
- This part includes only preparation patches; actual PHYLINK
integration will follow
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move flow control register configuration from
lan78xx_update_flowcontrol() into a new helper function
lan78xx_configure_flowcontrol(). This separates hardware-specific
programming from policy logic and simplifies the upcoming phylink
integration.
The values used in this initial version of
lan78xx_configure_flowcontrol() are taken over as-is from the original
implementation to avoid functional changes. While they may not be
optimal for all USB and link speed combinations, they are known to work
reliably. Optimization of pause time and thresholds based on runtime
conditions can be done in a separate follow-up patch.
The forward declaration of lan78xx_configure_flowcontrol() will also be
removed later during the phylink conversion.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the USB link power configuration logic from lan78xx_link_reset()
to a new helper function lan78xx_configure_usb(). This simplifies the
main link reset path and isolates USB-specific logic.
The new function handles U1/U2 enablement based on Ethernet link speed,
but only for SuperSpeed-capable devices (LAN7800 and LAN7801). LAN7850,
a High-Speed-only device, is explicitly excluded. A warning is logged
if SuperSpeed is reported unexpectedly for LAN7850.
Add a forward declaration for lan78xx_configure_usb() as preparation for
the upcoming phylink conversion, where it will also be used from the
mac_link_up() callback.
Open questions remain:
- Why is the 1000 Mbps configuration split into two steps (U2 disable,
then U1 enable), unlike the single-step config used for 10/100 Mbps?
- U1/U2 behavior appears to depend on proper EEPROM configuration.
There are known devices in the field without EEPROM. Should the driver
enforce safe defaults in such cases?
Due to lack of USB subsystem expertise, no changes were made to this logic
beyond structural refactoring.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the PHY interrupt acknowledgment logic from lan78xx_link_reset()
to a new helper function lan78xx_phy_int_ack(). This simplifies the
code and prepares for reusing the acknowledgment logic independently
from the full link reset process, such as when using phylink.
No functional change intended.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract the LED enable logic based on the "microchip,led-modes"
property into a new helper function lan78xx_configure_leds_from_dt().
This simplifies lan78xx_phy_init() and improves modularity.
No functional changes intended.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Split out PHY detection into lan78xx_get_phy() and MAC-side setup into
lan78xx_mac_prepare_for_phy(), making the main lan78xx_phy_init() cleaner
and easier to follow.
This improves separation of concerns and prepares the code for a future
transition to phylink. Fixed PHY registration and interface selection
are now handled in lan78xx_get_phy(), while MAC-side delay configuration
is done in lan78xx_mac_prepare_for_phy().
The fixed PHY fallback is preserved for setups like EVB-KSZ9897-1,
where LAN7801 connects directly to a KSZ switch without a standard PHY
or device tree support.
No functional changes intended.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RGMII timing correctness relies on the PHY providing internal delays.
This is typically ensured via PHY driver, strap pins, or PCB layout.
Explicitly checking for a PHY driver here is unnecessary and non-standard.
This logic applies to all MACs, not just LAN78xx, and should be left to
phylib, phylink, or platform configuration.
Drop the check and rely on standard subsystem behavior.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ensure that return values from `lan78xx_write_reg()`,
`lan78xx_read_reg()`, and `phy_find_first()` are properly checked and
propagated. Use `ERR_PTR(ret)` for error reporting in
`lan7801_phy_init()` and replace `-EIO` with `-ENODEV` where appropriate
to provide more accurate error codes.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With commit bcb5d6c76903 ("s390/pci: introduce lock to synchronize state
of zpci_dev's") the code to ignore power off of a PF that has child VFs
was changed from a direct return to a goto to the unlock and
pci_dev_put() section. The change however left the existing pci_dev_put()
untouched resulting in a doubple put. This can subsequently cause a use
after free if the struct pci_dev is released in an unexpected state.
Fix this by removing the extra pci_dev_put().
Cc: stable@vger.kernel.org
Fixes: bcb5d6c76903 ("s390/pci: introduce lock to synchronize state of zpci_dev's")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The zpci_create_device() function returns an error pointer that needs to
be checked before dereferencing it as a struct zpci_dev pointer. Add the
missing check in __clp_add() where it was missed when adding the
scan_list in the fixed commit. Simply not adding the device to the scan
list results in the previous behavior.
Cc: stable@vger.kernel.org
Fixes: 0467cdde8c43 ("s390/pci: Sort PCI functions prior to creating virtual busses")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
UDF maintains total length of all extents in i_lenExtents. Generally we
keep extent lengths (and thus i_lenExtents) block aligned because it
makes the file appending logic simpler. However the standard mandates
that the inode size must match the length of all extents and thus we
trim the last extent when closing the file. To catch possible bugs we
also verify that i_lenExtents matches i_size when evicting inode from
memory. Commit b405c1e58b73 ("udf: refactor udf_next_aext() to handle
error") however broke the code updating i_lenExtents and thus
udf_evict_inode() ended up spewing lots of errors about incorrectly
sized extents although the extents were actually sized properly. Fix the
updating of i_lenExtents to silence the errors.
Fixes: b405c1e58b73 ("udf: refactor udf_next_aext() to handle error")
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
I found this simple bug while preparing some patches for pKVM.
AFAICT, it should be harmless (besides crashing the kernel if it
was misbehaving)
Fixes: e94a7dea2972 ("KVM: arm64: Move host page ownership tracking to the hyp vmemmap")
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Link: https://lore.kernel.org/r/20250501162450.2784043-1-smostafa@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
HCRX_HOST_FLAGS, like most of these hardcoded setups, are not
a good match for options that can be selectively enabled or
disabled.
Nothing but the early setup is relying on it now, so kill the
macro and move the bag of bits where they belong.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20250430105916.3815157-3-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
Rather than restoring HCRX_EL2 to a fixed value on vcpu exit,
perform a full save/restore of the register, ensuring that
we don't lose bits that would have been set at some point in
the host kernel lifetime, such as the GCSEn bit.
Fixes: ff5181d8a2a82 ("arm64/gcs: Provide basic EL2 setup to allow GCS usage at EL0 and EL1")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20250430105916.3815157-2-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
The original nvme subsystem design didn't have a CONNECTING state; the
state machine allowed transitions from RESETTING to LIVE directly.
With the introduction of nvme fabrics the CONNECTING state was
introduce. Over time the nvme-pci started to use the CONNECTING state as
well.
Eventually, a bug fix for the nvme-fc started to depend that the only
valid transition to LIVE was from CONNECTING. Though this change didn't
update the firmware update handler which was still depending on
RESETTING to LIVE transition.
The simplest way to address it for the time being is to switch into
CONNECTING state before going to LIVE state.
Fixes: d2fe192348f9 ("nvme: only allow entering LIVE from CONNECTING state")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Closes: https://lore.kernel.org/all/0134ea15-8d5f-41f7-9e9a-d7e6d82accaa@roeck-us.net
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
|
|
For UHR, a version 3 of the rate API is being added, which
increases the number of bits used for MCSes by shifting the
NSS bit up. Handle that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250505215513.84cde65a603f.Ic3119ef77cbc6461abd2a6bda104c0d236adcc8d@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Add RFI_CONFIG_CMD into the names array to facilitate the
display of this command name when sending it to the firmware.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Somashekhar Puttagangaiah <somashekhar.puttagangaiah@intel.com>
Link: https://patch.msgid.link/20250505215513.da89484cb838.I755709232f5e441ca159bdc5a151bac73d9744d3@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
That mask should never have been 0xFFFF (mask also doesn't
make sense in that case) but rather 0xF000 since I combined
a few entries with 0xC___.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250505215513.63bdbd67b72d.Id9b93b695c91117967dfd339c76bdfcd2872bee6@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
This sets both fwrt->uats_valid and returns 0, but in the
static inline it returns 0 without setting uats_valid,
which is confusing and the iwlmvm code misbehaves in this
case.
Since it already sets uats_valid, just remove the extra
return value.
Reported-by: Bjoern A. Zeeb <bz@FreeBSD.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250505215513.e981a7911228.Ic94b5e03e2053a08b84cabeb58ce3b6598fd9fc6@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
This RF module is now a product. No need to support the test chip
anymore.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250505215513.01fb866e7c38.I23611aa4abb8fd031a6d63a21f4b87b0d38a36a1@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
This is a new RF module and of course the firmware name for this new RF
module is different.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250505215513.c3481b1a4124.Id94c680636be2f59c9172919c79d80a48c7d1322@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
In order to set the CDB indication in the dump meta data, we read it from
a specific prph register.
There is a known issue with that register in Xnj setups - in that case it
will always indicate CDB.
Instead of detecting the jacket case and then hardcode whether the CDB
indication should or shouldn't be set (according the CRF),
we can retrieve the CDB bit from the hw_rf_id (CSR_HW_RF_ID).
There is also no reason to do it conditionally only for ax210 / BnJ.
Cleanup the code a bit.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250505215513.ea542a6c189e.I3d8cf5103b3747dfdd89985b45b592e419f97b63@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
The beacon CCK flag should be set for any CCK rate, not
just for 1 Mbps. Fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Link: https://patch.msgid.link/20250505215513.fe18b7d92d7d.I7bb40a92cea102677b695beb1e2a62a5ea72678b@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
This was used for debug/bringup of 8000 devices, to be able to
unify between all 8000 devices with NVM override. However, this
is really no longer used, those are ancient devices by now, so
we can remove the logic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250505215513.6210ac6cda09.I83cc3e68f0ed99a922d435c203fef840a28eb0de@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
These should be zero, but we might as well be explicit about it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250505215513.1e943bf696f4.Id2d7a413dc594c4525ac7ad0650ec8a50e1970ca@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Add a debugfs option to use the ptp clock time for Rx device
timestamps on a monitor interface. This can be useful for e.g.
synchronizing multiple NICs or reporting the timestamp in the
system clock instead of the GP2.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Link: https://patch.msgid.link/20250505215513.fffe6718fbca.I75f034005851a2d0c8ba5b015b9fdcad8a7c550d@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
Currently, there are two log messages at INFO level for
synchronous commands:
Attempting to send sync command ...
Setting HCMD_ACTIVE for command ...
and unfortunately none at all for async ones. Add one
for async commands as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250505215512.cc4457285889.I633fae8828e8a37bbebc578166f388dcf893f592@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
If there is an ongoing scan that lasts long, the MPDU counters may not
increase enough due the device being busy with scanning and not
because we are in a low throughput scenario.
In that case we don't want to block EMLSR.
Instead, stop checking the counters from the moment we started
scanning, and when the scan ends - clear the counters and schedule a
check in 5 seconds, as usual.
Note that this is only done for regular scan since MLO scan is too short
to affect the counters, and scheduled scan is mainly used when we are
not connected.
Also note that we only stop checking whether to block EMLSR, and not if to
unblock.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250505215512.330ea440d19c.Ib10dae0b7a0cb0e10c59a9edf5ff7af0f065ac60@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
We have such a print for ACPI, add one for UEFI.
This is needed for testing
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250505215512.f419c18c064e.I870a4537a4bfa3c54b03ec7ec29bb246e6aa75cb@changeid
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
|
|
If there's a failure and the op-mode didn't actually fully
initialize, it should leave the transport again. Fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.714c3517548b.I49557e7ba8c03be2b558cc9fb5efa2a9fbab890e@changeid
|
|
There's no need to build a list of individual configs
first and then compare them, we can just go through all
of them and compare if the pointers aren't the same.
The complexity (in terms of number of comparisons) is a
bit higher that way, but it's just a test and the code
complexity is much lower without that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.85911c59d96a.I540f464229da3566d1726dfb61b46002fbb73bde@changeid
|
|
For Sc 97 might get used (at least for now) and for Dr
the older 96 won't get used. Change them both to 97.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.2ab49f2265ce.I45623943fdcac3462d96e54dbb7fdad68bdf3693@changeid
|
|
For different MACs we maintain the configs in different
files, and while it's a small waste of space, this is a
worthwhile trade-off for maintenance and simplicity. So
allow different MAC types to have the same config. This
could allow the same config for two MACs in the same MAC
family, but that's not hugely important. Also simplify
the test to not build a config list, there's no good
reason to do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.27f5d570eb32.I1649309a0e54a1d446a38c5b2124a582de9f6d61@changeid
|
|
Start supporting API version 99 for those devices.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.677db25ce2c7.Ie4a7a00ff3562bfed1e8ac1fb42c1382cd24a486@changeid
|
|
No hardware that uses iwlmvm actually supports HT greenfield.
Remove the support and then clean up the v1 rate API by doing
a conversion to v2 rate API, the only thing v1 covered that
couldn't be done in v2 was HT greenfield.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.805ec090c61f.Iafd87f62ceb463b72f861a5348078999dcaace92@changeid
|
|
In EHT, we shouldn't report a legacy rate to mac80211, that
might just be confusing. Set it to zero, since it's only
really relevant for radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.325d7ba6905f.I3bdd8854e1a784856a4973ff4d532c74f992af00@changeid
|
|
In EHT, we shouldn't report a legacy rate to mac80211, that
might just be confusing. Set it to zero, since it's only
really relevant for radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.8baf4efec182.Idc0cabf1919c05b35dc2341c08ea88a7157614c4@changeid
|
|
Instead of building the injected rate in version 1 of the
format and then converting, build it in version 2 directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.0e6e4ae4469f.Ib49eda9a3083b2e0f0bcaff08ad784e151978307@changeid
|
|
The modulation type values aren't masks, they're just values.
Rename them from RATE_MCS_CCK_* to RATE_MCS_MOD_TYPE_*.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.aa79635dd4e6.Ie97a01fee1ef4aedf8a2e5447489793ce8c15ca0@changeid
|
|
We can use u32_{get,encode}_bits() instead of manual shifts
and remove RATE_MCS_NSS_POS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.b6da6048f8b8.Ib6d78ed6ffb7e99c42c2dd2ca4706a6bf73d3066@changeid
|
|
This is ephemeral data that's passed from the alive
response to the PNVM loading, so it doesn't need to
be stored. Pass it around instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.fe8be4454007.I24824f35620b21fe49e9243818c7188e431af48e@changeid
|
|
This value is used for the device start, so it's really
part of the configuration.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.637ed7514587.I6c8fdeb3e2078a5fe9b755391e3ef7258ef2b279@changeid
|
|
This really belongs there, it's needed early, so move it. Remove
the related but dead iwl_trans_pcie_ctx_info_gen3_set_step() while
at it. In iwlmld move the calls since they do part of the trans
configuration.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.a4681ee11dd7.I6434a13d51932e984bb07695bc1cb931ebdcd27c@changeid
|
|
Instead of having a trans_configure method that copies all
the data, just have the users set up the configuration in
the transport directly. This simplifies the code on both
sides. While doing so also move some value from the trans
struct into the conf struct because they are configuration.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250504132447.e2a2535ecfd0.I21653103ff02afc5a4d97a41b68021f053985e37@changeid
|
