summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2023-06-09net: phy: broadcom: Rename LED registersFlorian Fainelli
These registers are common to most PHYs and are not specific to the BCM5482, renamed the constants accordingly, no functional change. Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-06-09net/sched: act_pedit: Parse L3 Header for L4 offsetMax Tottenham
Instead of relying on skb->transport_header being set correctly, opt instead to parse the L3 header length out of the L3 headers for both IPv4/IPv6 when the Extended Layer Op for tcp/udp is used. This fixes a bug if GRO is disabled, when GRO is disabled skb->transport_header is set by __netif_receive_skb_core() to point to the L3 header, it's later fixed by the upper protocol layers, but act_pedit will receive the SKB before the fixups are completed. The existing behavior causes the following to edit the L3 header if GRO is disabled instead of the UDP header: tc filter add dev eth0 ingress protocol ip flower ip_proto udp \ dst_ip 192.168.1.3 action pedit ex munge udp set dport 18053 Also re-introduce a rate-limited warning if we were unable to extract the header offset when using the 'ex' interface. Fixes: 71d0ed7079df ("net/act_pedit: Support using offset relative to the conventional network headers") Signed-off-by: Max Tottenham <mtottenh@akamai.com> Reviewed-by: Josh Hunt <johunt@akamai.com> Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202305261541.N165u9TZ-lkp@intel.com/ Reviewed-by: Pedro Tammela <pctammela@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-06-09Merge branch 'net-ncsi-refactoring-for-GMA-cmd'David S. Miller
Ivan Mikhaylov says: ==================== net/ncsi: refactoring for GMA command Make one GMA function for all manufacturers, change ndo_set_mac_address to dev_set_mac_address for notifiying net layer about MAC change which ndo_set_mac_address doesn't do. Changes from v1: 1. delete ftgmac100.txt changes about mac-address-increment 2. add convert to yaml from ftgmac100.txt 3. add mac-address-increment option for ethernet-controller.yaml Changes from v2: 1. remove DT changes from series, will be done in another one ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2023-06-09net/ncsi: change from ndo_set_mac_address to dev_set_mac_addressIvan Mikhaylov
Change ndo_set_mac_address to dev_set_mac_address because dev_set_mac_address provides a way to notify network layer about MAC change. In other case, services may not aware about MAC change and keep using old one which set from network adapter driver. As example, DHCP client from systemd do not update MAC address without notification from net subsystem which leads to the problem with acquiring the right address from DHCP server. Fixes: cb10c7c0dfd9e ("net/ncsi: Add NCSI Broadcom OEM command") Cc: stable@vger.kernel.org # v6.0+ 2f38e84 net/ncsi: make one oem_gma function for all mfr id Signed-off-by: Paul Fertser <fercerpav@gmail.com> Signed-off-by: Ivan Mikhaylov <fr0st61te@gmail.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-06-09net/ncsi: make one oem_gma function for all mfr idIvan Mikhaylov
Make the one Get Mac Address function for all manufacturers and change this call in handlers accordingly. Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Ivan Mikhaylov <fr0st61te@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-06-09usbnet: ipheth: update Kconfig descriptionFoster Snowhill
This module has for a long time not been limited to iPhone <= 3GS. Update description to match the actual state of the driver. Remove dead link from 2010, instead reference an existing userspace iOS device pairing implementation as part of libimobiledevice. Signed-off-by: Foster Snowhill <forst@pen.gy> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-06-09usbnet: ipheth: add CDC NCM supportFoster Snowhill
Recent iOS releases support CDC NCM encapsulation on RX. This mode is the default on macOS and Windows. In this mode, an iOS device may include one or more Ethernet frames inside a single URB. Freshly booted iOS devices start in legacy mode, but are put into NCM mode by the official Apple driver. When reconnecting such a device from a macOS/Windows machine to a Linux host, the device stays in NCM mode, making it unusable with the legacy ipheth driver code. To correctly support such a device, the driver has to either support the NCM mode too, or put the device back into legacy mode. To match the behaviour of the macOS/Windows driver, and since there is no documented control command to revert to legacy mode, implement NCM support. The device is attempted to be put into NCM mode by default, and falls back to legacy mode if the attempt fails. Signed-off-by: Foster Snowhill <forst@pen.gy> Tested-by: Georgi Valkov <gvalkov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-06-09usbnet: ipheth: transmit URBs without trailing paddingFoster Snowhill
The behaviour of the official iOS tethering driver on macOS is to not transmit any trailing padding at the end of URBs. This is applicable to both NCM and legacy modes, including older devices. Adapt the driver to not include trailing padding in TX URBs, matching the behaviour of the official macOS driver. Signed-off-by: Foster Snowhill <forst@pen.gy> Tested-by: Georgi Valkov <gvalkov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-06-09usbnet: ipheth: fix risk of NULL pointer deallocationGeorgi Valkov
The cleanup precedure in ipheth_probe will attempt to free a NULL pointer in dev->ctrl_buf if the memory allocation for this buffer is not successful. While kfree ignores NULL pointers, and the existing code is safe, it is a better design to rearrange the goto labels and avoid this. Signed-off-by: Georgi Valkov <gvalkov@gmail.com> Signed-off-by: Foster Snowhill <forst@pen.gy> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-06-09Merge tag 'v6.4-rc5' into v4l_for_linusMauro Carvalho Chehab
Linux 6.4-rc5 * tag 'v6.4-rc5': (303 commits) Linux 6.4-rc5 leds: qcom-lpg: Fix PWM period limits selftests/ftrace: Choose target function for filter test from samples KVM: selftests: Add test for race in kvm_recalculate_apic_map() KVM: x86: Bail from kvm_recalculate_phys_map() if x2APIC ID is out-of-bounds KVM: x86: Account fastpath-only VM-Exits in vCPU stats KVM: SVM: vNMI pending bit is V_NMI_PENDING_MASK not V_NMI_BLOCKING_MASK KVM: x86/mmu: Grab memslot for correct address space in NX recovery worker tpm, tpm_tis: correct tpm_tis_flags enumeration values Revert "ext4: remove ac->ac_found > sbi->s_mb_min_to_scan dead check in ext4_mb_check_limits" riscv: Implement missing huge_ptep_get riscv: Fix huge_ptep_set_wrprotect when PTE is a NAPOT module/decompress: Fix error checking on zstd decompression fork, vhost: Use CLONE_THREAD to fix freezer/ps regression dt-bindings: serial: 8250_omap: add rs485-rts-active-high selinux: don't use make's grouped targets feature yet riscv: perf: Fix callchain parse error with kernel tracepoint events mptcp: fix active subflow finalization mptcp: add annotations around sk->sk_shutdown accesses mptcp: fix data race around msk->first access ...
2023-06-09powerpc/64s/radix: Fix exit lazy tlb mm switch with irqs enabledNicholas Piggin
Switching mm and tinkering with current->active_mm should be done with irqs disabled. There is a path where exit_lazy_flush_tlb can be called with irqs enabled: exit_lazy_flush_tlb flush_type_needed __flush_all_mm tlb_finish_mmu exit_mmap Which results in the switching being done with irqs enabled, which is incorrect. Fixes: a665eec0a22e ("powerpc/64s/radix: Fix mm_cpumask trimming race vs kthread_use_mm") Cc: stable@vger.kernel.org # v5.10+ Reported-by: Sachin Sant <sachinp@linux.ibm.com> Link: https://lore.kernel.org/linuxppc-dev/A9A5D83D-BA70-47A4-BCB4-30C1AE19BC22@linux.ibm.com/ Tested-by: Sachin Sant <sachinp@linux.ibm.com> Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230607005601.583293-1-npiggin@gmail.com
2023-06-09xfrm: fix inbound ipv4/udp/esp packets to UDPv6 dualstack socketsMaciej Żenczykowski
Before Linux v5.8 an AF_INET6 SOCK_DGRAM (udp/udplite) socket with SOL_UDP, UDP_ENCAP, UDP_ENCAP_ESPINUDP{,_NON_IKE} enabled would just unconditionally use xfrm4_udp_encap_rcv(), afterwards such a socket would use the newly added xfrm6_udp_encap_rcv() which only handles IPv6 packets. Cc: Sabrina Dubroca <sd@queasysnail.net> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Benedict Wong <benedictwong@google.com> Cc: Yan Yan <evitayan@google.com> Fixes: 0146dca70b87 ("xfrm: add support for UDPv6 encapsulation of ESP") Signed-off-by: Maciej Żenczykowski <maze@google.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2023-06-08Merge branch ↵Jakub Kicinski
'splice-net-rewrite-splice-to-socket-fix-splice_f_more-and-handle-msg_splice_pages-in-af_tls' David Howells says: ==================== splice, net: Rewrite splice-to-socket, fix SPLICE_F_MORE and handle MSG_SPLICE_PAGES in AF_TLS Here are patches to do the following: (1) Block MSG_SENDPAGE_* flags from leaking into ->sendmsg() from userspace, whilst allowing splice_to_socket() to pass them in. (2) Allow MSG_SPLICE_PAGES to be passed into tls_*_sendmsg(). Until support is added, it will be ignored and a splice-driven sendmsg() will be treated like a normal sendmsg(). TCP, UDP, AF_UNIX and Chelsio-TLS already handle the flag in net-next. (3) Replace a chain of functions to splice-to-sendpage with a single function to splice via sendmsg() with MSG_SPLICE_PAGES. This allows a bunch of pages to be spliced from a pipe in a single call using a bio_vec[] and pushes the main processing loop down into the bowels of the protocol driver rather than repeatedly calling in with a page at a time. (4) Provide a ->splice_eof() op[2] that allows splice to signal to its output that the input observed a premature EOF and that the caller didn't flag SPLICE_F_MORE, thereby allowing a corked socket to be flushed. This attempts to maintain the current behaviour. It is also not called if we didn't manage to read any data and so didn't called the actor function. This needs routing though several layers to get it down to the network protocol. [!] Note that I chose not to pass in any flags - I'm not sure it's particularly useful to pass in the splice flags; I also elected not to return any error code - though we might actually want to do that. (5) Provide tls_{device,sw}_splice_eof() to flush a pending TLS record if there is one. (6) Provide splice_eof() for UDP, TCP, Chelsio-TLS and AF_KCM. AF_UNIX doesn't seem to pay attention to the MSG_MORE or MSG_SENDPAGE_NOTLAST flags. (7) Alter the behaviour of sendfile() and fix SPLICE_F_MORE/MSG_MORE signalling[1] such SPLICE_F_MORE is always signalled until we have read sufficient data to finish the request. If we get a zero-length before we've managed to splice sufficient data, we now leave the socket expecting more data and leave it to userspace to deal with it. (8) Make AF_TLS handle the MSG_SPLICE_PAGES internal sendmsg flag. MSG_SPLICE_PAGES is an internal hint that tells the protocol that it should splice the pages supplied if it can. Its sendpage implementations are then turned into wrappers around that. Link: https://lore.kernel.org/r/499791.1685485603@warthog.procyon.org.uk/ [1] Link: https://lore.kernel.org/r/CAHk-=wh=V579PDYvkpnTobCLGczbgxpMgGmmhqiTyE34Cpi5Gg@mail.gmail.com/ [2] Link: https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=51c78a4d532efe9543a4df019ff405f05c6157f6 # part 1 Link: https://lore.kernel.org/r/20230524153311.3625329-1-dhowells@redhat.com/ # v1 ==================== Link: https://lore.kernel.org/r/20230607181920.2294972-1-dhowells@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08tls/device: Convert tls_device_sendpage() to use MSG_SPLICE_PAGESDavid Howells
Convert tls_device_sendpage() to use sendmsg() with MSG_SPLICE_PAGES rather than directly splicing in the pages itself. With that, the tls_iter_offset union is no longer necessary and can be replaced with an iov_iter pointer and the zc_page argument to tls_push_data() can also be removed. This allows ->sendpage() to be replaced by something that can handle multiple multipage folios in a single transaction. Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Jakub Kicinski <kuba@kernel.org> cc: Chuck Lever <chuck.lever@oracle.com> cc: Boris Pismenny <borisp@nvidia.com> cc: John Fastabend <john.fastabend@gmail.com> cc: Jens Axboe <axboe@kernel.dk> cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08tls/device: Support MSG_SPLICE_PAGESDavid Howells
Make TLS's device sendmsg() support MSG_SPLICE_PAGES. This causes pages to be spliced from the source iterator if possible. This allows ->sendpage() to be replaced by something that can handle multiple multipage folios in a single transaction. Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> cc: Chuck Lever <chuck.lever@oracle.com> cc: Boris Pismenny <borisp@nvidia.com> cc: John Fastabend <john.fastabend@gmail.com> cc: Jens Axboe <axboe@kernel.dk> cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08tls/sw: Convert tls_sw_sendpage() to use MSG_SPLICE_PAGESDavid Howells
Convert tls_sw_sendpage() and tls_sw_sendpage_locked() to use sendmsg() with MSG_SPLICE_PAGES rather than directly splicing in the pages itself. [!] Note that tls_sw_sendpage_locked() appears to have the wrong locking upstream. I think the caller will only hold the socket lock, but it should hold tls_ctx->tx_lock too. This allows ->sendpage() to be replaced by something that can handle multiple multipage folios in a single transaction. Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> cc: Chuck Lever <chuck.lever@oracle.com> cc: Boris Pismenny <borisp@nvidia.com> cc: John Fastabend <john.fastabend@gmail.com> cc: Jens Axboe <axboe@kernel.dk> cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08tls/sw: Support MSG_SPLICE_PAGESDavid Howells
Make TLS's sendmsg() support MSG_SPLICE_PAGES. This causes pages to be spliced from the source iterator if possible. This allows ->sendpage() to be replaced by something that can handle multiple multipage folios in a single transaction. Signed-off-by: David Howells <dhowells@redhat.com> cc: Chuck Lever <chuck.lever@oracle.com> cc: Boris Pismenny <borisp@nvidia.com> cc: John Fastabend <john.fastabend@gmail.com> cc: Jens Axboe <axboe@kernel.dk> cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08splice, net: Fix SPLICE_F_MORE signalling in splice_direct_to_actor()David Howells
splice_direct_to_actor() doesn't manage SPLICE_F_MORE correctly[1] - and, as a result, it incorrectly signals/fails to signal MSG_MORE when splicing to a socket. The problem I'm seeing happens when a short splice occurs because we got a short read due to hitting the EOF on a file: as the length read (read_len) is less than the remaining size to be spliced (len), SPLICE_F_MORE (and thus MSG_MORE) is set. The issue is that, for the moment, we have no way to know *why* the short read occurred and so can't make a good decision on whether we *should* keep MSG_MORE set. MSG_SENDPAGE_NOTLAST was added to work around this, but that is also set incorrectly under some circumstances - for example if a short read fills a single pipe_buffer, but the next read would return more (seqfile can do this). This was observed with the multi_chunk_sendfile tests in the tls kselftest program. Some of those tests would hang and time out when the last chunk of file was less than the sendfile request size: build/kselftest/net/tls -r tls.12_aes_gcm.multi_chunk_sendfile This has been observed before[2] and worked around in AF_TLS[3]. Fix this by making splice_direct_to_actor() always signal SPLICE_F_MORE if we haven't yet hit the requested operation size. SPLICE_F_MORE remains signalled if the user passed it in to splice() but otherwise gets cleared when we've read sufficient data to fulfill the request. If, however, we get a premature EOF from ->splice_read(), have sent at least one byte and SPLICE_F_MORE was not set by the caller, ->splice_eof() will be invoked. Signed-off-by: David Howells <dhowells@redhat.com> cc: Linus Torvalds <torvalds@linux-foundation.org> cc: Jens Axboe <axboe@kernel.dk> cc: Christoph Hellwig <hch@lst.de> cc: Al Viro <viro@zeniv.linux.org.uk> cc: Matthew Wilcox <willy@infradead.org> cc: Jan Kara <jack@suse.cz> cc: Jeff Layton <jlayton@kernel.org> cc: David Hildenbrand <david@redhat.com> cc: Christian Brauner <brauner@kernel.org> cc: Chuck Lever <chuck.lever@oracle.com> cc: Boris Pismenny <borisp@nvidia.com> cc: John Fastabend <john.fastabend@gmail.com> cc: linux-mm@kvack.org Link: https://lore.kernel.org/r/499791.1685485603@warthog.procyon.org.uk/ [1] Link: https://lore.kernel.org/r/1591392508-14592-1-git-send-email-pooja.trivedi@stackpath.com/ [2] Link: https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=d452d48b9f8b1a7f8152d33ef52cfd7fe1735b0a [3] Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08kcm: Use splice_eof() to flushDavid Howells
Allow splice to undo the effects of MSG_MORE after prematurely ending a splice/sendfile due to getting an EOF condition (->splice_read() returned 0) after splice had called sendmsg() with MSG_MORE set when the user didn't set MSG_MORE. Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Link: https://lore.kernel.org/r/CAHk-=wh=V579PDYvkpnTobCLGczbgxpMgGmmhqiTyE34Cpi5Gg@mail.gmail.com/ Signed-off-by: David Howells <dhowells@redhat.com> cc: Tom Herbert <tom@herbertland.com> cc: Tom Herbert <tom@quantonium.net> cc: Cong Wang <cong.wang@bytedance.com> cc: Jens Axboe <axboe@kernel.dk> cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08chelsio/chtls: Use splice_eof() to flushDavid Howells
Allow splice to end a Chelsio TLS record after prematurely ending a splice/sendfile due to getting an EOF condition (->splice_read() returned 0) after splice had called sendmsg() with MSG_MORE set when the user didn't set MSG_MORE. Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Link: https://lore.kernel.org/r/CAHk-=wh=V579PDYvkpnTobCLGczbgxpMgGmmhqiTyE34Cpi5Gg@mail.gmail.com/ Signed-off-by: David Howells <dhowells@redhat.com> cc: Ayush Sawal <ayush.sawal@chelsio.com> cc: Jens Axboe <axboe@kernel.dk> cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08ipv4, ipv6: Use splice_eof() to flushDavid Howells
Allow splice to undo the effects of MSG_MORE after prematurely ending a splice/sendfile due to getting an EOF condition (->splice_read() returned 0) after splice had called sendmsg() with MSG_MORE set when the user didn't set MSG_MORE. For UDP, a pending packet will not be emitted if the socket is closed before it is flushed; with this change, it be flushed by ->splice_eof(). For TCP, it's not clear that MSG_MORE is actually effective. Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Link: https://lore.kernel.org/r/CAHk-=wh=V579PDYvkpnTobCLGczbgxpMgGmmhqiTyE34Cpi5Gg@mail.gmail.com/ Signed-off-by: David Howells <dhowells@redhat.com> cc: Kuniyuki Iwashima <kuniyu@amazon.com> cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com> cc: David Ahern <dsahern@kernel.org> cc: Jens Axboe <axboe@kernel.dk> cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08tls/device: Use splice_eof() to flushDavid Howells
Allow splice to end a TLS record after prematurely ending a splice/sendfile due to getting an EOF condition (->splice_read() returned 0) after splice had called TLS with a sendmsg() with MSG_MORE set when the user didn't set MSG_MORE. Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Link: https://lore.kernel.org/r/CAHk-=wh=V579PDYvkpnTobCLGczbgxpMgGmmhqiTyE34Cpi5Gg@mail.gmail.com/ Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> cc: Chuck Lever <chuck.lever@oracle.com> cc: Boris Pismenny <borisp@nvidia.com> cc: John Fastabend <john.fastabend@gmail.com> cc: Jens Axboe <axboe@kernel.dk> cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08tls/sw: Use splice_eof() to flushDavid Howells
Allow splice to end a TLS record after prematurely ending a splice/sendfile due to getting an EOF condition (->splice_read() returned 0) after splice had called TLS with a sendmsg() with MSG_MORE set when the user didn't set MSG_MORE. Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Link: https://lore.kernel.org/r/CAHk-=wh=V579PDYvkpnTobCLGczbgxpMgGmmhqiTyE34Cpi5Gg@mail.gmail.com/ Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> cc: Chuck Lever <chuck.lever@oracle.com> cc: Boris Pismenny <borisp@nvidia.com> cc: John Fastabend <john.fastabend@gmail.com> cc: Jens Axboe <axboe@kernel.dk> cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08splice, net: Add a splice_eof op to file-ops and socket-opsDavid Howells
Add an optional method, ->splice_eof(), to allow splice to indicate the premature termination of a splice to struct file_operations and struct proto_ops. This is called if sendfile() or splice() encounters all of the following conditions inside splice_direct_to_actor(): (1) the user did not set SPLICE_F_MORE (splice only), and (2) an EOF condition occurred (->splice_read() returned 0), and (3) we haven't read enough to fulfill the request (ie. len > 0 still), and (4) we have already spliced at least one byte. A further patch will modify the behaviour of SPLICE_F_MORE to always be passed to the actor if either the user set it or we haven't yet read sufficient data to fulfill the request. Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Link: https://lore.kernel.org/r/CAHk-=wh=V579PDYvkpnTobCLGczbgxpMgGmmhqiTyE34Cpi5Gg@mail.gmail.com/ Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> cc: Jens Axboe <axboe@kernel.dk> cc: Christoph Hellwig <hch@lst.de> cc: Al Viro <viro@zeniv.linux.org.uk> cc: Matthew Wilcox <willy@infradead.org> cc: Jan Kara <jack@suse.cz> cc: Jeff Layton <jlayton@kernel.org> cc: David Hildenbrand <david@redhat.com> cc: Christian Brauner <brauner@kernel.org> cc: Chuck Lever <chuck.lever@oracle.com> cc: Boris Pismenny <borisp@nvidia.com> cc: John Fastabend <john.fastabend@gmail.com> cc: linux-mm@kvack.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08splice, net: Use sendmsg(MSG_SPLICE_PAGES) rather than ->sendpage()David Howells
Replace generic_splice_sendpage() + splice_from_pipe + pipe_to_sendpage() with a net-specific handler, splice_to_socket(), that calls sendmsg() with MSG_SPLICE_PAGES set instead of calling ->sendpage(). MSG_MORE is used to indicate if the sendmsg() is expected to be followed with more data. This allows multiple pipe-buffer pages to be passed in a single call in a BVEC iterator, allowing the processing to be pushed down to a loop in the protocol driver. This helps pave the way for passing multipage folios down too. Protocols that haven't been converted to handle MSG_SPLICE_PAGES yet should just ignore it and do a normal sendmsg() for now - although that may be a bit slower as it may copy everything. Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> cc: Jens Axboe <axboe@kernel.dk> cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08tls: Allow MSG_SPLICE_PAGES but treat it as normal sendmsgDavid Howells
Allow MSG_SPLICE_PAGES to be specified to sendmsg() but treat it as normal sendmsg for now. This means the data will just be copied until MSG_SPLICE_PAGES is handled. Signed-off-by: David Howells <dhowells@redhat.com> cc: Chuck Lever <chuck.lever@oracle.com> cc: Boris Pismenny <borisp@nvidia.com> cc: John Fastabend <john.fastabend@gmail.com> cc: Jens Axboe <axboe@kernel.dk> cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08net: Block MSG_SENDPAGE_* from being passed to sendmsg() by userspaceDavid Howells
It is necessary to allow MSG_SENDPAGE_* to be passed into ->sendmsg() to allow sendmsg(MSG_SPLICE_PAGES) to replace ->sendpage(). Unblocking them in the network protocol, however, allows these flags to be passed in by userspace too[1]. Fix this by marking MSG_SENDPAGE_NOPOLICY, MSG_SENDPAGE_NOTLAST and MSG_SENDPAGE_DECRYPTED as internal flags, which causes sendmsg() to object if they are passed to sendmsg() by userspace. Network protocol ->sendmsg() implementations can then allow them through. Note that it should be possible to remove MSG_SENDPAGE_NOTLAST once sendpage is removed as a whole slew of pages will be passed in in one go by splice through sendmsg, with MSG_MORE being set if it has more data waiting in the pipe. Signed-off-by: David Howells <dhowells@redhat.com> cc: Chuck Lever <chuck.lever@oracle.com> cc: Boris Pismenny <borisp@nvidia.com> cc: John Fastabend <john.fastabend@gmail.com> cc: Jens Axboe <axboe@kernel.dk> cc: Matthew Wilcox <willy@infradead.org> Link: https://lore.kernel.org/r/20230526181338.03a99016@kernel.org/ [1] Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08net: usb: qmi_wwan: add support for Compal RXM-G1Wes Huang
Add support for Compal RXM-G1 which is based on Qualcomm SDX55 chip. This patch adds support for two compositions: 0x9091: DIAG + MODEM + QMI_RMNET + ADB 0x90db: DIAG + DUN + RMNET + DPL + QDSS(Trace) + ADB T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0 D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1 P: Vendor=05c6 ProdID=9091 Rev= 4.14 S: Manufacturer=QCOM S: Product=SDXPRAIRIE-MTP _SN:719AB680 S: SerialNumber=719ab680 C:* #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=896mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none) E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=84(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=5000 MxCh= 0 D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1 P: Vendor=05c6 ProdID=90db Rev= 4.14 S: Manufacturer=QCOM S: Product=SDXPRAIRIE-MTP _SN:719AB680 S: SerialNumber=719ab680 C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=896mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none) E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan E: Ad=84(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=8f(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=85(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms Cc: stable@vger.kernel.org Signed-off-by: Wes Huang <wes.huang@moxa.com> Acked-by: Bjørn Mork <bjorn@mork.no> Link: https://lore.kernel.org/r/20230608030141.3546-1-wes.huang@moxa.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08tcp: let tcp_mtu_probe() build headless packetsEric Dumazet
tcp_mtu_probe() is still copying payload from skbs in the write queue, using skb_copy_bits(), ignoring potential errors. Modern TCP stack wants to only deal with payload found in page frags, as this is a prereq for TCPDirect (host stack might not have access to the payload) Signed-off-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20230607214113.1992947-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08Merge tag 'mlx5-updates-2023-06-06' of ↵Jakub Kicinski
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5-updates-2023-06-06 1) Support 4 ports VF LAG, part 2/2 2) Few extra trivial cleanup patches Shay Drory Says: ================ Support 4 ports VF LAG, part 2/2 This series continues the series[1] "Support 4 ports VF LAG, part1/2". This series adds support for 4 ports VF LAG (single FDB E-Switch). This series of patches refactoring LAG code that make assumptions about VF LAG supporting only two ports and then enable 4 ports VF LAG. Patch 1: - Fix for ib rep code Patches 2-5: - Refactors LAG layer. Patches 6-7: - Block LAG types which doesn't support 4 ports. Patch 8: - Enable 4 ports VF LAG. This series specifically allows HCAs with 4 ports to create a VF LAG with only 4 ports. It is not possible to create a VF LAG with 2 or 3 ports using HCAs that have 4 ports. Currently, the Merged E-Switch feature only supports HCAs with 2 ports. However, upcoming patches will introduce support for HCAs with 4 ports. In order to activate VF LAG a user can execute: devlink dev eswitch set pci/0000:08:00.0 mode switchdev devlink dev eswitch set pci/0000:08:00.1 mode switchdev devlink dev eswitch set pci/0000:08:00.2 mode switchdev devlink dev eswitch set pci/0000:08:00.3 mode switchdev ip link add name bond0 type bond ip link set dev bond0 type bond mode 802.3ad ip link set dev eth2 master bond0 ip link set dev eth3 master bond0 ip link set dev eth4 master bond0 ip link set dev eth5 master bond0 Where eth2, eth3, eth4 and eth5 are net-interfaces of pci/0000:08:00.0 pci/0000:08:00.1 pci/0000:08:00.2 pci/0000:08:00.3 respectively. User can verify LAG state and type via debugfs: /sys/kernel/debug/mlx5/0000\:08\:00.0/lag/state /sys/kernel/debug/mlx5/0000\:08\:00.0/lag/type [1] https://lore.kernel.org/netdev/20230601060118.154015-1-saeed@kernel.org/T/#mf1d2083780970ba277bfe721554d4925f03f36d1 ================ * tag 'mlx5-updates-2023-06-06' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux: net/mlx5e: simplify condition after napi budget handling change mlx5/core: E-Switch, Allocate ECPF vport if it's an eswitch manager net/mlx5: Skip inline mode check after mlx5_eswitch_enable_locked() failure net/mlx5e: TC, refactor access to hash key net/mlx5e: Remove RX page cache leftovers net/mlx5e: Expose catastrophic steering error counters net/mlx5: Enable 4 ports VF LAG net/mlx5: LAG, block multiport eswitch LAG in case ldev have more than 2 ports net/mlx5: LAG, block multipath LAG in case ldev have more than 2 ports net/mlx5: LAG, change mlx5_shared_fdb_supported() to static net/mlx5: LAG, generalize handling of shared FDB net/mlx5: LAG, check if all eswitches are paired for shared FDB {net/RDMA}/mlx5: introduce lag_for_each_peer RDMA/mlx5: Free second uplink ib port ==================== Link: https://lore.kernel.org/r/20230607210410.88209-1-saeed@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08ethtool: ioctl: improve error checking for set_wolJustin Chen
The netlink version of set_wol checks for not supported wolopts and avoids setting wol when the correct wolopt is already set. If we do the same with the ioctl version then we can remove these checks from the driver layer. Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Justin Chen <justin.chen@broadcom.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://lore.kernel.org/r/1686179653-29750-1-git-send-email-justin.chen@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08Merge branch 'complete-lynx-mdio-device-handling'Jakub Kicinski
Russell King says: ==================== complete Lynx mdio device handling This series completes the mdio device lifetime handling for Lynx PCS users which do not create their own mdio device, but instead fetch it using a firmware description - namely the DPAA2 and FMAN_MEMAC drivers. In a previous patch set, lynx_pcs_create() was modified to increase the mdio device refcount, and lynx_pcs_destroy() to drop that refcount. The first two patches change these two drivers to put the reference which they hold immediately after lynx_pcs_create(), effectively handing the responsibility for maintaining the refcount to the Lynx PCS driver. A side effect of the first two patches is that lynx_get_mdio_device() is no longer used, so patch 3 removes it. Patch 4 adds a new helper - lynx_pcs_create_fwnode(), which creates a Lynx PCS instance from the fwnode. Patch 5 and 6 convert the two drivers to make use of this new helper, which simply has to find the mdio device, and then create the Lynx PCS from that. With those conversions done, lynx_pcs_create() is no longer required outside pcs-lynx.c, so remove it from public view. Patch 8 we changes lynx_pcs_create() to return an error-pointer rather than NULL to bring consistency to the return style, and means that we can remove the NULL-to-error-pointer conversion from both lynx_pcs_create_fwnode() and lynx_pcs_create_mdiodev(). Patch 9 adds a check for the fwnode being available, and returns an -ENODEV error pointer if unavailable. Patch 10 removes this check from DPAA2, detecting the error pointer value to continue printing the helpful message. Patch 11 removes this check from fman_memac, and in doing so fixes a bug where if the node is unavailable, the reference count is not dropped. ==================== Link: https://lore.kernel.org/r/ZIBwuw+IuGQo5yV8@shell.armlinux.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08net: fman_memac: use pcs-lynx's check for fwnode availabilityRussell King (Oracle)
Use pcs-lynx's check rather than our own when determining if the device is available. This fixes a bug where the reference gained by of_parse_phandle() is not dropped if the device is not available. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08net: dpaa2: use pcs-lynx's check for fwnode availabilityRussell King (Oracle)
Use pcs-lynx's check rather than our own when determining if the device is available. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08net: pcs: lynx: check that the fwnode is available prior to useRussell King (Oracle)
Check that the fwnode is marked as available prior to trying to lookup the PCS device, and return -ENODEV if unavailable. Document the return codes from lynx_pcs_create_fwnode(). Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08net: pcs: lynx: change lynx_pcs_create() to return error-pointersRussell King (Oracle)
Change lynx_pcs_create() to return an error-pointer on failure to allocate memory, rather than returning NULL. This allows the removal of the conversion in lynx_pcs_create_fwnode() and lynx_pcs_create_mdiodev(). Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08net: pcs: lynx: make lynx_pcs_create() staticRussell King (Oracle)
We no longer need to export lynx_pcs_create() for drivers to use as we now have all the functionality we need in the two new creation helpers. Remove the export and prototype, and make it static. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08net: fman_memac: use lynx_pcs_create_fwnode()Russell King (Oracle)
Use lynx_pcs_create_fwnode() to create a lynx PCS from a fwnode handle. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08net: dpaa2-mac: use lynx_pcs_create_fwnode()Russell King (Oracle)
Use lynx_pcs_create_fwnode() to create a lynx PCS from a fwnode handle. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08net: pcs: lynx: add lynx_pcs_create_fwnode()Russell King (Oracle)
Add a helper to create a lynx PCS from a fwnode handle. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08net: pcs: lynx: remove lynx_get_mdio_device()Russell King (Oracle)
lynx_get_mdio_device() is no longer necessary, let's remove it so the lynx PCS code is always managing the lifetime of the mdiodev. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08net: fman_memac: allow lynx PCS to handle mdiodev lifetimeRussell King (Oracle)
Put the mdiodev after lynx_pcs_create() so that the Lynx PCS driver can manage the lifetime of the mdiodev its using. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08net: dpaa2-mac: allow lynx PCS to manage mdiodev lifetimeRussell King (Oracle)
Put the mdiodev after lynx_pcs_create() so that the Lynx PCS driver can manage the lifetime of the mdiodev its using. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08net: pch_gbe: Allow build on MIPS_GENERIC kernelJiaxun Yang
MIPS Boston board, which is using MIPS_GENERIC kernel is using EG20T PCH and thus need this driver. Dependency of PCH_GBE, PTP_1588_CLOCK_PCH is also fixed for MIPS_GENERIC. Note that CONFIG_PCH_GBE is selected in arch/mips/configs/generic/ board-boston.config for a while, some how it's never wired up in Kconfig. Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230607055953.34110-1-jiaxun.yang@flygoat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08Merge tag 'drm-fixes-2023-06-09' of git://anongit.freedesktop.org/drm/drmLinus Torvalds
Pull drm fixes from Dave Airlie: "Bit busier and a bit more scattered than usual. amdgpu is the main one, with ivpu and msm having a few fixes, then i915, exynos, ast, lima, radeon with some misc bits, but overall nothing standing out. fb-helper: - Fill in fb-helper vars more correctly amdgpu: - S0ix fixes - GPU reset fixes - SMU13 fixes - SMU11 fixes - Misc Display fixes - Revert RV/RV2/PCO clock counter changes - Fix Stoney xclk value - Fix reserved vram debug info radeon: - Fix a potential use after free i915: - CDCLK voltage fix for ADL-P - eDP wake sync pulse fix - Two error handling fixes to selftests exynos: - Fix wrong return in Exynos vidi driver - Fix use-after-free issue to Exynos g2d driver ast: - resume and modeset fixes for ast ivpu: - Assorted ivpu fixes lima: - lima context destroy fix msm: - Fix max segment size to address splat on newer a6xx - Disable PSR by default w/ modparam to re-enable, since there still seems to be a lingering issue - Fix HPD issue - Fix issue with unitialized GMU mutex" * tag 'drm-fixes-2023-06-09' of git://anongit.freedesktop.org/drm/drm: (32 commits) drm/msm/a6xx: initialize GMU mutex earlier drm/msm/dp: enable HDP plugin/unplugged interrupts at hpd_enable/disable accel/ivpu: Fix sporadic VPU boot failure accel/ivpu: Do not use mutex_lock_interruptible accel/ivpu: Do not trigger extra VPU reset if the VPU is idle drm/amd/display: Reduce sdp bw after urgent to 90% drm/amdgpu: change reserved vram info print drm/amdgpu: fix xclk freq on CHIP_STONEY drm/radeon: fix race condition UAF in radeon_gem_set_domain_ioctl Revert "drm/amdgpu: switch to golden tsc registers for raven/raven2" Revert "drm/amdgpu: Differentiate between Raven2 and Raven/Picasso according to revision id" Revert "drm/amdgpu: change the reference clock for raven/raven2" drm/amd/display: add ODM case when looking for first split pipe drm/amd: Make lack of `ACPI_FADT_LOW_POWER_S0` or `CONFIG_AMD_PMC` louder during suspend path drm/amd/pm: conditionally disable pcie lane switching for some sienna_cichlid SKUs drm/amd/pm: Fix power context allocation in SMU13 drm/amdgpu: fix Null pointer dereference error in amdgpu_device_recover_vram drm/amd: Disallow s0ix without BIOS support again drm/i915/selftests: Add some missing error propagation drm/exynos: fix race condition UAF in exynos_g2d_exec_ioctl ...
2023-06-08igb: Fix extts capture value format for 82580/i354/i350Yuezhen Luan
82580/i354/i350 features circle-counter-like timestamp registers that are different with newer i210. The EXTTS capture value in AUXTSMPx should be converted from raw circle counter value to timestamp value in resolution of 1 nanosec by the driver. This issue can be reproduced on i350 nics, connecting an 1PPS signal to a SDP pin, and run 'ts2phc' command to read external 1PPS timestamp value. On i210 this works fine, but on i350 the extts is not correctly converted. The i350/i354/82580's SYSTIM and other timestamp registers are 40bit counters, presenting time range of 2^40 ns, that means these registers overflows every about 1099s. This causes all these regs can't be used directly in contrast to the newer i210/i211s. The igb driver needs to convert these raw register values to valid time stamp format by using kernel timecounter apis for i350s families. Here the igb_extts() just forgot to do the convert. Fixes: 38970eac41db ("igb: support EXTTS on 82580/i354/i350") Signed-off-by: Yuezhen Luan <eggcar.luan@gmail.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230607164116.3768175-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08ping6: Fix send to link-local addresses with VRF.Guillaume Nault
Ping sockets can't send packets when they're bound to a VRF master device and the output interface is set to a slave device. For example, when net.ipv4.ping_group_range is properly set, so that ping6 can use ping sockets, the following kind of commands fails: $ ip vrf exec red ping6 fe80::854:e7ff:fe88:4bf1%eth1 What happens is that sk->sk_bound_dev_if is set to the VRF master device, but 'oif' is set to the real output device. Since both are set but different, ping_v6_sendmsg() sees their value as inconsistent and fails. Fix this by allowing 'oif' to be a slave device of ->sk_bound_dev_if. This fixes the following kselftest failure: $ ./fcnal-test.sh -t ipv6_ping [...] TEST: ping out, vrf device+address bind - ns-B IPv6 LLA [FAIL] Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Closes: https://lore.kernel.org/netdev/b6191f90-ffca-dbca-7d06-88a9788def9c@alu.unizg.hr/ Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Fixes: 5e457896986e ("net: ipv6: Fix ping to link-local addresses.") Signed-off-by: Guillaume Nault <gnault@redhat.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/6c8b53108816a8d0d5705ae37bdc5a8322b5e3d9.1686153846.git.gnault@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08mlxsw: spectrum_nve_vxlan: Fix unsupported flag regressionIdo Schimmel
The recently added 'VXLAN_F_LOCALBYPASS' flag is set by default on VXLAN devices and denotes a behavior that is irrelevant for the hardware data path. Add it to the lists of IPv4 and IPv6 supported flags to avoid rejecting offload of VXLAN devices which have this flag set. Fixes: 69474a8a5837 ("net: vxlan: Add nolocalbypass option to vxlan.") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/5533e63643bf719bbe286fef60f749c9cad35005.1686139716.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2023-06-08Merge tag 'cgroup-for-6.4-rc5-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup Pull cgroup fixes from Tejun Heo: - Fix css_set reference leaks on fork failures - Fix CPU hotplug locking in cgroup_transfer_tasks() which is used by cgroup1 cpuset - Doc update * tag 'cgroup-for-6.4-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: cgroup: Documentation: Clarify usage of memory limits cgroup: always put cset in cgroup_css_set_put_fork cgroup: fix missing cpus_read_{lock,unlock}() in cgroup_transfer_tasks()
2023-06-09Merge tag 'drm-msm-fixes-2023-06-08' of ↵Dave Airlie
https://gitlab.freedesktop.org/drm/msm into drm-fixes A few more late fixes for v6.4-rc6 + Fix max segment size to address splat on newer a6xx + Disable PSR by default w/ modparam to re-enable, since there still seems to be a lingering issue + Fix HPD issue + Fix issue with unitialized GMU mutex Signed-off-by: Dave Airlie <airlied@redhat.com> From: Rob Clark <robdclark@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGufjVZRNT6YfQ7YUXFC7Cz95wdLF7QHAYkiGfp+3Xc3DQ@mail.gmail.com
generated by cgit (git 2.34.1) at 2025-09-23 11:27:15 +0000