| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C driver bugfixes for mlxbf and imx, a few documentation fixes after
the rework this cycle, and one hardening for the i2c-mux core"
* tag 'i2c-for-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mux: harden i2c_mux_alloc() against integer overflows
i2c: mlxbf: Fix frequency calculation
i2c: mlxbf: prevent stack overflow in mlxbf_i2c_smbus_start_transaction()
i2c: mlxbf: incorrect base address passed during io write
Documentation: i2c: fix references to other documents
MAINTAINERS: remove Nehal Shah from AMD MP2 I2C DRIVER
i2c: imx: If pm_runtime_get_sync() returned 1 device access is possible
|
|
Since commit edc6afc54968 ("tty: switch to ktermios and new framework")
termios speed is no longer stored only in c_cflag member but also in new
additional c_ispeed and c_ospeed members. If BOTHER flag is set in c_cflag
then termios speed is stored only in these new members.
Since commit 027b57170bf8 ("serial: core: Fix initializing and restoring
termios speed") termios speed is available also in struct console.
So properly restore also c_ispeed and c_ospeed members after suspend to fix
restoring termios speed which is not represented by Bnnn constant.
Fixes: 4516d50aabed ("serial: 8250: Use canary to restart console after suspend")
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220924104324.4035-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a UART port is newly registered, uart_configure_port() seeks to
deassert RS485 Transmit Enable by setting the RTS bit in port->mctrl.
However a number of UART drivers interpret a set RTS bit as *assertion*
instead of deassertion: Affected drivers include those using
serial8250_em485_config() (except 8250_bcm2835aux.c) and some using
mctrl_gpio (e.g. imx.c).
Since the interpretation of the RTS bit is driver-specific, it is not
suitable as a means to centrally deassert Transmit Enable in the serial
core. Instead, the serial core must call on drivers to deassert it in
their driver-specific way. One way to achieve that is to call
->rs485_config(). It implicitly deasserts Transmit Enable.
So amend uart_configure_port() and uart_resume_port() to invoke
uart_rs485_config(). That allows removing calls to uart_rs485_config()
from drivers' ->probe() hooks and declaring the function static.
Skip any invocation of ->set_mctrl() if RS485 is enabled. RS485 has no
hardware flow control, so the modem control lines are irrelevant and
need not be touched. When leaving RS485 mode, reset the modem control
lines to the state stored in port->mctrl. That way, UARTs which are
muxed between RS485 and RS232 transceivers drive the lines correctly
when switched to RS232. (serial8250_do_startup() historically raises
the OUT1 modem signal because otherwise interrupts are not signaled on
ancient PC UARTs, but I believe that no longer applies to modern,
RS485-capable UARTs and is thus safe to be skipped.)
imx.c modifies port->mctrl whenever Transmit Enable is asserted and
deasserted. Stop it from doing that so port->mctrl reflects the RS232
line state.
8250_omap.c deasserts Transmit Enable on ->runtime_resume() by calling
->set_mctrl(). Because that is now a no-op in RS485 mode, amend the
function to call serial8250_em485_stop_tx().
fsl_lpuart.c retrieves and applies the RS485 device tree properties
after registering the UART port. Because applying now happens on
registration in uart_configure_port(), move retrieval of the properties
ahead of uart_add_one_port().
Link: https://lore.kernel.org/all/20220329085050.311408-1-matthias.schiffer@ew.tq-group.com/
Link: https://lore.kernel.org/all/8f538a8903795f22f9acc94a9a31b03c9c4ccacb.camel@ginzinger.com/
Fixes: d3b3404df318 ("serial: Fix incorrect rs485 polarity on uart open")
Cc: stable@vger.kernel.org # v4.14+
Reported-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reported-by: Roosen Henri <Henri.Roosen@ginzinger.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/2de36eba3fbe11278d5002e4e501afe0ceaca039.1663863805.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
uart_xmit_advance() provides a common way on how to advance
the Tx queue. Use it for the sake of unification and robustness.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220909091102.58941-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
uart_xmit_advance() provides a common way on how to advance
the Tx queue. Use it for the sake of unification and robustness.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220909091258.68886-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty") into tty-next
We need the tty fixes and api additions in this branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since intertouch was enabled for the T14 and P14s AMD G1 laptops there
have been a number of reports of touchpads not working well.
Debugging this with Synaptics they noted that intertouch should not be
enabled as SMBUS host notify is not available on these laptops.
Reverting the previous commit (e4ce4d3a939d97bea045eafa13ad1195695f91ce)
to restore functionality back to what it was.
Note - we are working with Synaptics to see if there is a better
solution, but nothing is confirmed as yet.
Signed-off-by: Mark Pearson <markpearson@lenovo.com>
Link: https://lore.kernel.org/r/20220920193936.8709-1-markpearson@lenovo.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Each call to device/fwnode_get_named_child_node() must be matched
with a call to fwnode_handle_put() once the corresponding node is
no longer in use. This ensures a reference count remains balanced
in the case of dynamic device tree support.
Currently, the driver never calls fwnode_handle_put(). This patch
adds the missing calls.
Fixes: ce1cb0eec85b ("input: keyboard: Add support for Azoteq IQS620A/621/622/624/625")
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/YyYbYvlkq5cy55dc@nixie71
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
devm_gpiod_get_optional() may return ERR_PTR(-EPROBE_DEFER),
add a minus sign to fix it.
Fixes: 6ccb1d8f78bd ("Input: add MELFAS MIP4 Touchscreen driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220924030715.1653538-1-yangyingliang@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Pick up another "Soft Reservation" fix for v6.0-final on top of some
straggling nvdimm fixes that missed v5.19.
|
|
The "hmem" platform-devices that are created to represent the
platform-advertised "Soft Reserved" memory ranges end up inserting a
resource that causes the iomem_resource tree to look like this:
340000000-43fffffff : hmem.0
340000000-43fffffff : Soft Reserved
340000000-43fffffff : dax0.0
This is because insert_resource() reparents ranges when they completely
intersect an existing range.
This matters because code that uses region_intersects() to scan for a
given IORES_DESC will only check that top-level 'hmem.0' resource and
not the 'Soft Reserved' descendant.
So, to support EINJ (via einj_error_inject()) to inject errors into
memory hosted by a dax-device, be sure to describe the memory as
IORES_DESC_SOFT_RESERVED. This is a follow-on to:
commit b13a3e5fd40b ("ACPI: APEI: Fix _EINJ vs EFI_MEMORY_SP")
...that fixed EINJ support for "Soft Reserved" ranges in the first
instance.
Fixes: 262b45ae3ab4 ("x86/efi: EFI soft reservation to E820 enumeration")
Reported-by: Ricardo Sandoval Torres <ricardo.sandoval.torres@intel.com>
Tested-by: Ricardo Sandoval Torres <ricardo.sandoval.torres@intel.com>
Cc: <stable@vger.kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Omar Avelar <omar.avelar@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mark Gross <markgross@kernel.org>
Link: https://lore.kernel.org/r/166397075670.389916.7435722208896316387.stgit@dwillia2-xfh.jf.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Fix build error for the combination of SYSTEM_TRUSTED_KEYRING=y and
X509_CERTIFICATE_PARSER=m
- Fix DEBUG_INFO_SPLIT to generate debug info for GCC 11+ and Clang 12+
- Revive debug info for assembly files
- Remove unused code
* tag 'kbuild-fixes-v6.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
Makefile.debug: re-enable debug info for .S files
Makefile.debug: set -g unconditional on CONFIG_DEBUG_INFO_SPLIT
certs: make system keyring depend on built-in x509 parser
Kconfig: remove unused function 'menu_get_root_menu'
scripts/clang-tools: remove unused module
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fix from Vasily Gorbik:
- Fix potential hangs in VFIO AP driver
* tag 's390-6.0-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/vfio-ap: bypass unnecessary processing of AP resources
|
|
Intel Xeon servers used to use a fixed energy resolution (15.3uj) for
Dram RAPL domain. But on SPR, Dram RAPL domain follows the standard
energy resolution as described in MSR_RAPL_POWER_UNIT.
Remove the SPR dram_domain_energy_unit quirk.
Fixes: 2d798d9f5967 ("powercap: intel_rapl: add support for Sapphire Rapids")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Wang Wendy <wendy.wang@intel.com>
Cc: 5.9+ <stable@vger.kernel.org> # 5.9+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The prospective callers of rpm_resume() passing RPM_NOWAIT to it may
be confused when it returns 0 without actually resuming the device
which may happen if the device is suspending at the given time and it
will only resume when the suspend in progress has completed. To avoid
that confusion, return -EINPROGRESS from rpm_resume() in that case.
Since none of the current callers passing RPM_NOWAIT to rpm_resume()
check its return value, this change has no functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Since PCI provides helper macro module_pci_driver(), the
module_init/exit code can be replaced with it.
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add the board data describing the regulators for the Microsoft
Surface Go line's IR camera.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently, we only support passing a single gpiod_lookup_table as part
of the board data for the tps68470 driver. This carries the implicit
assumption that each TPS68470 device will only support a single
sensor, which does not hold true.
Extend the code to support the possibility of multiple sensors each
having a gpiod_lookup_table, and opportunistically add the lookup
table for the Surface Go line's IR camera.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
At present, the tps68470.c only supports a single clock consumer when
passing platform data to the clock driver. In some devices multiple
sensors depend on the clock provided by a single TPS68470 and so all
need to be able to acquire the clock. Support passing multiple
consumers as platform data.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add a helper macro to iterate over ACPI devices that are flagged
as consumers of an initial supplier ACPI device.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In commit b83e2b306736 ("ACPI: scan: Add function to fetch dependent
of ACPI device") we added a means of fetching the first device to
declare itself dependent on another ACPI device in the _DEP method.
One assumption in that patch was that there would only be a single
consuming device, but this has not held.
Replace that function with a new function that fetches the next consumer
of a supplier device. Where no "previous" consumer is passed in, it
behaves identically to the original function.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The Asus Vivobook S5402ZA has the same keyboard issue as Asus Vivobook
K3402ZA/K3502ZA. The kernel overrides IRQ 1 to Edge_High when it
should be Active_Low.
This patch adds the S5402ZA model to the quirk list.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216158
Tested-by: Kellen Renshaw <kellen.renshaw@canonical.com>
Signed-off-by: Kellen Renshaw <kellen.renshaw@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add ACPI ID for ARM DMA-330 controller to AMBA id supported list to
allow the probing of the device.
Signed-off-by: Vijayenthiran Subramaniam <vijayenthiran.subramaniam@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Return the erst_get_record_id_begin() and apei_exec_write_register()
return values directly instead of storing them in redundant local
variables.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Having the driver struct at the end of the file isn't only more usual, it
also allows to drop a few forward declarations which are just useless
repetition.
While at it also move the MODULE_... macros to the end of the file.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
PCC regions utilize a mailbox to set/retrieve register values used by
the CPPC code. This is fine as long as the operations are
infrequent. With the FIE code enabled though the overhead can range
from 2-11% of system CPU overhead (ex: as measured by top) on Arm
based machines.
So, before enabling FIE assure none of the registers used by
cppc_get_perf_ctrs() are in the PCC region. Finally, add a module
parameter which can override the PCC region detection at boot or
module reload.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Use _DMA defined in ACPI spec for translation between
DMA address and CPU address, and implement acpi_arch_dma_setup
for initializing dev->dma_range_map, where acpi_dma_get_range
is called for parsing _DMA.
e.g.
If we have two dma ranges:
cpu address dma address size offset
0x200080000000 0x2080000000 0x400000000 0x1fe000000000
0x400080000000 0x4080000000 0x400000000 0x3fc000000000
_DMA for pci devices should be declared in host bridge as
flowing:
Name (_DMA, ResourceTemplate() {
QWordMemory (ResourceProducer,
PosDecode,
MinFixed,
MaxFixed,
NonCacheable,
ReadWrite,
0x0,
0x4080000000,
0x447fffffff,
0x3fc000000000,
0x400000000,
,
,
)
QWordMemory (ResourceProducer,
PosDecode,
MinFixed,
MaxFixed,
NonCacheable,
ReadWrite,
0x0,
0x2080000000,
0x247fffffff,
0x1fe000000000,
0x400000000,
,
,
)
})
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In DT systems configurations, of_dma_get_range() returns struct
bus_dma_region DMA regions; they are used to set-up devices
DMA windows with different offset available for translation between DMA
address and CPU address.
In ACPI systems configuration, acpi_dma_get_range() does not return
DMA regions yet and that precludes setting up the dev->dma_range_map
pointer and therefore DMA regions with multiple offsets.
Update acpi_dma_get_range() to return struct bus_dma_region
DMA regions like of_dma_get_range() does.
After updating acpi_dma_get_range(), acpi_arch_dma_setup() is changed for
ARM64, where the original dma_addr and size are removed as these
arguments are now redundant, and pass 0 and U64_MAX for dma_base
and size of arch_setup_dma_ops; this is a simplification consistent
with what other ACPI architectures also pass to iommu_setup_dma_ops().
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Reviewed-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In commit 57a183222271 ("ACPI / x86: Introduce an
acpi_quirk_skip_acpi_ac_and_battery() helper"), the usage of struct
acpi_ac_bl was removed, but left the definition of the struct in
the file, so remove the useless code.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Dell Inspiron 14 2-in-1 has two ACPI nodes under GPP1 both with _ADR of
0, both without _HID. It's ambiguous which the kernel should take, but
it seems to take "DEV0". Unfortunately "DEV0" is missing the device
property `StorageD3Enable` which is present on "NVME".
To avoid this causing problems for suspend, add a quirk for this system
to behave like `StorageD3Enable` property was found.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216440
Reported-and-tested-by: Luya Tshimbalanga <luya@fedoraproject.org>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
All uses of pnpid32_to_pnpid() were removed by
commit 25eb846189d2 ("PNP: add pnp_eisa_id_to_string()"),
so remove the declaration, too.
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix an uninitialized variable usage in the operating performance
points code and add missing DT bindings for it.
Specifics:
- Fix uninitialized variable usage in dev_pm_opp_config_clks_simple()
(Christophe JAILLET)
- Add missing OPP DT properties (Rob Herring)"
* tag 'pm-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
dt-bindings: opp: Add missing (unevaluated|additional)Properties on child nodes
OPP: Fix an un-initialized variable usage
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are three tiny driver fixes for 6.0-rc7. They include:
- phy driver reset bugfix
- fpga memleak bugfix
- counter irq config bugfix
The first two have been in linux-next for a while, the last one has
only been added to my tree in the past few days, but was in linux-next
under a different commit id. I couldn't pull directly from the counter
tree due to some gpg key propagation issue, so I took the commit
directly from email instead"
* tag 'char-misc-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
counter: 104-quad-8: Fix skipped IRQ lines during events configuration
fpga: m10bmc-sec: Fix possible memory leak of flash_buf
phy: marvell: phy-mvebu-a3700-comphy: Remove broken reset support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small, and late, serial driver fixes for 6.0-rc7 to
resolve some reported problems.
Included in here are:
- tegra icount accounting fixes, including a framework function that
other drivers will be converted over to using in 6.1-rc1.
- fsl_lpuart reset bugfix
- 8250 omap 485 bugfix
- sifive serial clock bugfix
The last three patches have not shown up in linux-next due to them
being added to my tree only 2 days ago, but they are tiny and
self-contained and the developers say they resolve issues that they
have with 6.0-rc. The other three have been in linux-next for a while
with no reported issues"
* tag 'tty-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sifive: enable clocks for UART when probed
serial: 8250: omap: Use serial8250_em485_supported
serial: fsl_lpuart: Reset prior to registration
serial: tegra-tcu: Use uart_xmit_advance(), fixes icount.tx accounting
serial: tegra: Use uart_xmit_advance(), fixes icount.tx accounting
serial: Create uart_xmit_advance()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
- Add Waiman Long as a cpuset maintainer
- cgroup_get_from_id() could be fed a kernfs ID which doesn't point to
a cgroup directory but a knob file and then crash. Error out if the
lookup kernfs_node isn't a directory.
* tag 'cgroup-for-6.0-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: cgroup_get_from_id() must check the looked-up kn is a directory
cpuset: Add Waiman Long as a cpuset maintainer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fix from Tejun Heo:
"Just one patch to improve flush lockdep coverage"
* tag 'wq-for-6.0-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: don't skip lockdep work dependency in cancel_work_sync()
|
|
Pull io_uring fix from Jens Axboe:
"Just a single fix for an issue with un-reaped IOPOLL requests on ring
exit"
* tag 'io_uring-6.0-2022-09-23' of git://git.kernel.dk/linux:
io_uring: ensure that cached task references are always put on exit
|
|
Pull block fixes from Jens Axboe:
"Fix a regression that's been plaguing us by reverting the offending
commit, as attempts to both reproduce the issue and fix it in a saner
fashion have failed.
Fix for a potential oops condition in the s390 dasd block driver"
* tag 'block-6.0-2022-09-22' of git://git.kernel.dk/linux:
Revert "block: freeze the queue earlier in del_gendisk"
s390/dasd: fix Oops in dasd_alias_get_start_dev due to missing pavgroup
|
|
High-performance NVMe devices usually support a large hw queues, which
ensures a 1:1 mapping of hctx and ctx. In this case there will be no
remote request, so we don't need to care about it.
Signed-off-by: Liu Song <liusong@linux.alibaba.com>
Link: https://lore.kernel.org/r/1663731123-81536-1-git-send-email-liusong@linux.alibaba.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
"tg->has_rules" is extended to "tg->has_rules_iops/bps", thus bios that
don't need to be throttled can be checked accurately.
With this patch, bio will be throttled if:
1) Bio is read/write, and corresponding read/write iops limit exist.
2) If corresponding doesn't exist, corresponding bps limit exist and
bio is not throttled before.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20220921095309.1481289-3-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently, "tg->has_rules" and "tg->flags & THROTL_TG_HAS_IOPS_LIMIT"
both try to bypass bios that don't need to be throttled, however, they are
a little redundant and both not perfect:
1) "tg->has_rules" only distinguish read and write, but not iops and bps
limit.
2) "tg->flags & THROTL_TG_HAS_IOPS_LIMIT" only check if iops limit
exist, read and write is not distinguished, and bps limit is not
checked.
tg->has_rules will extended to distinguish bps and iops in the following
patch. There is no need to keep the flag.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20220921095309.1481289-2-yukuai1@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Kernel test robot throws below warning ->
drivers/pcmcia/omap_cf.c:127:7: warning: variable 'control'
set but not used [-Wunused-but-set-variable]
Removed unused variable control.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Souptick Joarder (HPE) <jrdr.linux@gmail.com>
[linux@dominikbrodowski.net: retain omap_readw() call, as it might be required]
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
This patch try to fix the following error.
Wed Jun 1 22:19:30 2022 kern.warn kernel: [ 119.561227] ath11k c000000.wifi: peer already added vdev id 0 req, vdev id 1 present
Wed Jun 1 22:19:30 2022 kern.warn kernel: [ 119.561282] ath11k c000000.wifi: Failed to add peer: 28:c2:1f:xx:xx:xx for VDEV: 0
Wed Jun 1 22:19:30 2022 kern.warn kernel: [ 119.568053] ath11k c000000.wifi: Failed to add station: 28:c2:1f:xx:xx:xx for VDEV: 0
Wed Jun 1 22:19:31 2022 daemon.notice hostapd: wlan2: STA 28:c2:1f:xx:xx:xx IEEE 802.11: Could not add STA to kernel driver
Wed Jun 1 22:19:31 2022 daemon.notice hostapd: wlan2: STA 28:c2:1f:xx:xx:xx IEEE 802.11: did not acknowledge authentication response
Wed Jun 1 22:19:31 2022 daemon.notice hostapd: wlan1: AP-STA-DISCONNECTED 28:c2:1f:xx:xx:xx
Wed Jun 1 22:19:31 2022 daemon.info hostapd: wlan1: STA 28:c2:1f:xx:xx:xx IEEE 802.11: disassociated due to inactivity
Wed Jun 1 22:19:32 2022 daemon.info hostapd: wlan1: STA 28:c2:1f:xx:xx:xx IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
To repro this:
- Have 2 Wifi with the same bssid and pass on different band (2.4 and
5GHz)
- Enable 802.11r Fast Transaction with same mobility domain
- FT Protocol: FT over the Air
From a openwrt system issue the command (with the correct mac)
ubus call hostapd.wlan1 wnm_disassoc_imminent '{"addr":"28:C2:1F:xx:xx:xx"}'
Notice the log printing the errors.
The cause of this error has been investigated and we found that this is
related to the WiFi Fast Transaction feature. We observed that this is
triggered when the router tells the device to change band. In this case
the device first auth to the other band and then the disconnect path
from the prev band is triggered.
This is problematic with the current rhash implementation since the
addrs is used as key and the logic of "adding first, delete later"
conflicts with the rhash logic.
In fact peer addition will fail since the peer is already added and with
that fixed a peer deletion will cause unitended effect by removing the
peer just added.
Current solution to this is to add additional logic to the peer delete,
make sure we are deleting the correct peer taken from the rhash
table (and fallback to the peer list) and for the peer add logic delete
the peer entry for the rhash list before adding the new one (counting as
an error only when a peer with the same vlan_id is asked to be added).
With this change, a sta can correctly transition from 2.4GHz and 5GHZ
with no drop and no error are printed.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Fixes: 7b0c70d92a43 ("ath11k: Add peer rhash table support")
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220603164559.27769-1-ansuelsmth@gmail.com
|
|
Add const qualifier to the device_get_match_data() parameter.
Some of the future users may utilize this function without
forcing the type.
All the same, dev_fwnode() may be used with a const qualifier.
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220922135410.49694-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
upgrade the callchain to drm_dbg() and drm_dev_dbg(); add a struct
_ddebug ptr parameter to them, and supply that additional param by
replacing the '_no_desc' flavor of dyndbg Factory macro currently used
with the flavor that supplies the descriptor.
NOTES:
The descriptor gives these fns access to the decorator flags, but they
do none of the dynamic-prefixing done by dynamic_emit_prefix(), which
is currently static.
DRM already has conventions for logging/messaging; just tossing
optional decorations on top probably wouldn't help. Instead, existing
flags (or new ones, perhaps 'sd' ala lspci) can be used to make
current message conventions optional. This suggests a new
drmdbg_prefix_emit() to handle prefixing locally.
For CONFIG_DRM_USE_DYNAMIC_DEBUG=N, just pass null descriptor.
desc->class_id is redundant with category parameter, but its
availability is dependent on desc.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Link: https://lore.kernel.org/r/20220912052852.1123868-10-jim.cromie@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
drm_print.c calls pr_debug() just once, from __drm_printfn_debug(),
which is a generic/service fn. The callsite is compile-time enabled
by DEBUG in both DYNAMIC_DEBUG=y/n builds.
For dyndbg builds, reverting this callsite back to bare printk is
correcting a few anti-features:
1- callsite is generic, serves multiple drm users.
it is soft-wired on currently by #define DEBUG
could accidentally: #> echo -p > /proc/dynamic_debug/control
2- optional "decorations" by dyndbg are unhelpful/misleading here,
they describe only the generic site, not end users
IOW, 1,2 are unhelpful at best, and possibly confusing.
reverting yields a nominal data and text shrink:
text data bss dec hex filename
462583 36604 54592 553779 87333 /kernel/drivers/gpu/drm/drm.ko
462515 36532 54592 553639 872a7 -dirty/kernel/drivers/gpu/drm/drm.ko
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Link: https://lore.kernel.org/r/20220912052852.1123868-9-jim.cromie@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When CONFIG_DRM_USE_DYNAMIC_DEBUG=y, the drm.debug API (a macro stack,
calling _+drm_*dbg() eventually) invokes a dyndbg Factory macro to
create a descriptor for each callsite, thus making them individually
>control-able.
In this case, the calls to _drm_*dbg are unreachable unless the
callsite is enabled. So those calls can short-circuit their early
do-nothing returns. Provide and use __drm_debug_enabled(), to do this
when config'd, or the _raw flags-check otherwize.
And since dyndbg is in use, lets also instrument the remaining users
of drm_debug_enabled, by wrapping the _raw in a macro with a:
pr_debug("todo: is this frequent enough to optimize ?\n");
For CONFIG_DRM_USE_DYNAMIC_DEBUG=n, do no site instrumenting at all,
since JUMP_LABEL might be off, and we don't want to make work.
With drm, amdgpu, i915, nouveau loaded, heres remaining uses of
drm_debug_enabled(), which costs ~1.5kb data to control the
pr_debug("todo:..")s.
Some of those uses might be ok to use __drm_debug_enabled() by
inspection, others might warrant conversion to use dyndbg Factory
macros, and that would want callrate data to estimate the savings
possible. TBH, any remaining savings are probably small; drm.debug
covers the vast bulk of the uses. Maybe "vblank" is the exception.
:#> grep todo /proc/dynamic_debug/control | wc
21 168 2357
:#> grep todo /proc/dynamic_debug/control
drivers/gpu/drm/drm_edid_load.c:178 [drm]edid_load =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/drm_vblank.c:410 [drm]drm_crtc_accurate_vblank_count =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/drm_vblank.c:787 [drm]drm_crtc_vblank_helper_get_vblank_timestamp_internal =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/drm_vblank.c:1491 [drm]drm_vblank_restore =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/drm_vblank.c:1433 [drm]drm_vblank_enable =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/drm_plane.c:2168 [drm]drm_mode_setplane =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/display/drm_dp_mst_topology.c:1359 [drm_display_helper]drm_dp_mst_wait_tx_reply =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/display/drm_dp_mst_topology.c:2864 [drm_display_helper]process_single_tx_qlock =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/display/drm_dp_mst_topology.c:2909 [drm_display_helper]drm_dp_queue_down_tx =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/display/drm_dp_mst_topology.c:1686 [drm_display_helper]drm_dp_mst_update_slots =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/i915/display/intel_dp.c:1111 [i915]intel_dp_print_rates =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/i915/display/intel_backlight.c:5434 [i915]cnp_enable_backlight =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/i915/display/intel_backlight.c:5459 [i915]intel_backlight_device_register =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/i915/display/intel_opregion.c:43 [i915]intel_opregion_notify_encoder =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/i915/display/intel_opregion.c:53 [i915]asle_set_backlight =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/i915/display/intel_bios.c:1088 [i915]intel_bios_is_dsi_present =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/i915/display/intel_display_debugfs.c:6153 [i915]i915_drrs_ctl_set =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/i915/intel_pcode.c:26 [i915]snb_pcode_read =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/i915/i915_getparam.c:785 [i915]i915_getparam_ioctl =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/amd/amdgpu/vcn_v2_5.c:282 [amdgpu]vcn_v2_5_process_interrupt =_ "todo: maybe avoid via dyndbg\n"
drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:433 [amdgpu]vcn_v2_0_process_interrupt =_ "todo: maybe avoid via dyndbg\n"
:#>
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Link: https://lore.kernel.org/r/20220912052852.1123868-8-jim.cromie@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
drm_print defines all of these:
drm_dbg_{core,kms,prime,atomic,vbl,lease,_dp,_drmres}
but not drm_dbg_driver itself, since it was the original drm_dbg.
To improve namespace symmetry, change the drm_dbg defn to
drm_dbg_driver, and redef grandfathered name to symmetric one.
This will help with nouveau, which uses its own stack of macros to
construct calls to dev_info, dev_dbg, etc, for which adaptation means
drm_dbg_##driver constructs.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Link: https://lore.kernel.org/r/20220912052852.1123868-7-jim.cromie@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
lkp robot told me:
>> drivers/gpu/drm/drm_ioc32.c:989:2:
error: call to undeclared function '_dynamic_func_call_cls';
ISO C99 and later do not support implicit function declarations
[-Wimplicit-function-declaration]
DRM_DEBUG("comm=\"%s\", pid=%d, dev=0x%lx, auth=%d, %s\n",
Since that macro is defined in drm_print.h, and under DRM_USE_DYN*=y
configs, invokes dyndbg-factory macros, include dynamic_debug.h from
there too, so that those configs have the definitions of all the
macros in the callchain.
This is done as a separate patch mostly to see how lkp sorts it.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Link: https://lore.kernel.org/r/20220912052852.1123868-6-jim.cromie@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For CONFIG_DRM_USE_DYNAMIC_DEBUG=y, wrap __drm_dbg() & __drm_dev_dbg()
in one of dyndbg's Factory macros: _dynamic_func_call_no_desc().
This adds the callsite descriptor into the code, and an entry for each
into /proc/dynamic_debug/control.
#> echo class DRM_UT_ATOMIC +p > /proc/dynamic_debug/control
CONFIG_DRM_USE_DYNAMIC_DEBUG=y/n is configurable because of the .data
footprint cost of per-callsite control; 56 bytes/site * ~2k for i915,
~4k callsites for amdgpu. This is large enough that a kernel builder
might not want it.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Link: https://lore.kernel.org/r/20220912052852.1123868-5-jim.cromie@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
