| Age | Commit message (Collapse) | Author |
|---|
|
Use newly defined 'active-high' property to set the
VEND1_GLOBAL_LED_DRIVE_VDD bit and let 'active-low' clear that bit. This
reflects the technical reality which was inverted in the previous
description in which the 'active-low' property was used to actually set
the VEND1_GLOBAL_LED_DRIVE_VDD bit, which means that VDD (ie. supply
voltage) of the LED is driven rather than GND.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/86a413b4387c42dcb54f587cc2433a06f16aae83.1728558223.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In addition to 'active-low' and 'inactive-high-impedance' also
support 'active-high' property for PHY LED pin configuration.
As only either 'active-high' or 'active-low' can be set at the
same time, WARN and return an error in case both are set.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/91598487773d768f254d5faf06cf65b13e972f0e.1728558223.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Wei Fang says:
====================
make PHY output RMII reference clock
The TJA11xx PHYs have the capability to provide 50MHz reference clock
in RMII mode and output on REF_CLK pin. Therefore, add the new property
"nxp,rmii-refclk-output" to support this feature. This property is only
available for PHYs which use nxp-c45-tja11xx driver, such as TJA1103,
TJA1104, TJA1120 and TJA1121.
====================
Link: https://patch.msgid.link/20241010061944.266966-1-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
For TJA11xx PHYs, they have the capability to output 50MHz reference
clock on REF_CLK pin in RMII mode, which is called "revRMII" mode in
the PHY data sheet.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Per the RMII specification, the REF_CLK is sourced from MAC to PHY
or from an external source. But for TJA11xx PHYs, they support to
output a 50MHz RMII reference clock on REF_CLK pin. Previously the
"nxp,rmii-refclk-in" was added to indicate that in RMII mode, if
this property present, REF_CLK is input to the PHY, otherwise it
is output. This seems inappropriate now. Because according to the
RMII specification, the REF_CLK is originally input, so there is
no need to add an additional "nxp,rmii-refclk-in" property to
declare that REF_CLK is input.
Unfortunately, because the "nxp,rmii-refclk-in" property has been
added for a while, and we cannot confirm which DTS use the TJA1100
and TJA1101 PHYs, changing it to switch polarity will cause an ABI
break. But fortunately, this property is only valid for TJA1100 and
TJA1101. For TJA1103/TJA1104/TJA1120/TJA1121 PHYs, this property is
invalid because they use the nxp-c45-tja11xx driver, which is a
different driver from TJA1100/TJA1101. Therefore, for PHYs using
nxp-c45-tja11xx driver, add "nxp,rmii-refclk-out" property to
support outputting RMII reference clock on REF_CLK pin.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Previously, the domain_context_clear() function incorrectly called
pci_for_each_dma_alias() to set up context entries for non-PCI devices.
This could lead to kernel hangs or other unexpected behavior.
Add a check to only call pci_for_each_dma_alias() for PCI devices. For
non-PCI devices, domain_context_clear_one() is called directly.
Reported-by: Todd Brandt <todd.e.brandt@intel.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219363
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219349
Fixes: 9a16ab9d6402 ("iommu/vt-d: Make context clearing consistent with context mapping")
Cc: stable@vger.kernel.org
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20241014013744.102197-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into fixes
Arm SMMU fixes for 6.12
- Clarify warning message when failing to disable the MMU-500 prefetcher
- Fix undefined behaviour in calculation of L1 stream-table index when
32-bit StreamIDs are implemented
- Replace a rogue comma with a semicolon
|
|
The DisCo for SoundWire 2.0 spec adds support for a new
sdw-manager-list property. Add it in backwards-compatible mode with
'sdw-master-count', which assumed that all links between 0..count-1
exist.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20241001070611.63288-5-yung-chuan.liao@linux.intel.com
|
|
For some reason we used an array of one u8 when the specification
requires a u32.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20241001070611.63288-4-yung-chuan.liao@linux.intel.com
|
|
Optimize a bit by using an intermediate 'fwnode' variable.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20241001070611.63288-3-yung-chuan.liao@linux.intel.com
|
|
Remove unnecessary initialization and un-shadow return code.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20241001070611.63288-2-yung-chuan.liao@linux.intel.com
|
|
Commit b3e992f69c23 ("hwmon: (jc42) Strengthen detect function")
attempted to make the detect function more robust for
TSE2004-compliant devices by checking capability bits which, according
to the JEDEC 21-C specification, should always be set. Unfortunately,
not all real-world implementations fully adhere to this specification,
so this change caused a regression.
Stop testing bit 7 (EVSD) of the Capabilities register, as it was
found to be 0 on one real-world device.
Also stop testing bits 0 (EVENT) and 2 (RANGE) as vendor datasheets
(Renesas TSE2004GB2B0, ST STTS2004) suggest that they may not always
be set either.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Message-ID: <20241014141204.026f4641@endymion.delvare>
Fixes: b3e992f69c23 ("hwmon: (jc42) Strengthen detect function")
Message-ID: <20241014220426.0c8f4d9c@endymion.delvare>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Commit 1fd9e4f25782 ("selftests: make kselftest-clean remove libynl outputs")
added EXTRA_CLEAN of YNL generated files to ynl.mk. We already had
a EXTRA_CLEAN in the file including the snippet. Consolidate them.
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20241011230311.2529760-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Try to rebuild YNL if either user added a new family or the specs
of the families have changed. Stanislav's ncdevmem cause a false
positive build failure in NIPA because libynl.a isn't rebuilt
after ethtool is added to YNL_GENS.
Note that sha1sum is already used in other parts of the build system.
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20241011230311.2529760-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allows simplifying get_strings and avoids manual pointer manipulation.
Tested on Belkin RT1800.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://patch.msgid.link/20241011200225.7403-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allows simplifying get_strings and avoids manual pointer manipulation.
Tested on Turris Omnia.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://patch.msgid.link/20241011195955.7065-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Joe Damato says:
====================
Add support for per-NAPI config via netlink
Greetings:
Welcome to v6. Minor changes from v5 [1], please see changelog below.
There were no explicit comments from reviewers on the call outs in my
v5, so I'm retaining them from my previous cover letter just in case :)
A few important call outs for reviewers:
1. This revision seems to work (see below for a full walk through). I
think this is the behavior we talked about, but please let me know if
a use case is missing.
2. Re a previous point made by Stanislav regarding "taking over a NAPI
ID" when the channel count changes: mlx5 seems to call napi_disable
followed by netif_napi_del for the old queues and then calls
napi_enable for the new ones. In this RFC, the NAPI ID generation is
deferred to napi_enable. This means we won't end up with two of the
same NAPI IDs added to the hash at the same time.
Can we assume all drivers will napi_disable the old queues before
napi_enable the new ones?
- If yes: we might not need to worry about a NAPI ID takeover
function.
- If no: I'll need to make a change so that the NAPI ID generation
is deferred only for drivers which have opted into the config
space via calls to netif_napi_add_config
3. I made the decision to remove the WARN_ON_ONCE that (I think?)
Jakub previously suggested in alloc_netdev_mqs (WARN_ON_ONCE(txqs
!= rxqs);) because this was triggering on every kernel boot with my
mlx5 NIC.
4. I left the "maxqs = max(txqs, rxqs);" in alloc_netdev_mqs despite
thinking this is a bit strange. I think it's strange that we might
be short some number of NAPI configs, but it seems like most people
are in favor of this approach, so I've left it.
I'd appreciate thoughts from reviewers on the above items, if at all
possible.
Now, on to the implementation.
Firstly, this implementation moves certain settings to napi_struct so that
they are "per-NAPI", while taking care to respect existing sysfs
parameters which are interface wide and affect all NAPIs:
- NAPI ID
- gro_flush_timeout
- defer_hard_irqs
Furthermore:
- NAPI ID generation and addition to the hash is now deferred to
napi_enable, instead of during netif_napi_add
- NAPIs are removed from the hash during napi_disable, instead of
netif_napi_del.
- An array of "struct napi_config" is allocated in net_device.
IMPORTANT: The above changes affect all network drivers.
Optionally, drivers may opt-in to using their config space by calling
netif_napi_add_config instead of netif_napi_add.
If a driver does this, the NAPI being added is linked with an allocated
"struct napi_config" and the per-NAPI settings (including NAPI ID) are
persisted even as hardware queues are destroyed and recreated.
To help illustrate how this would end up working, I've added patches for
3 drivers, of which I have access to only 1:
- mlx5 which is the basis of the examples below
- mlx4 which has TX only NAPIs, just to highlight that case. I have
only compile tested this patch; I don't have this hardware.
- bnxt which I have only compiled tested. I don't have this
hardware.
NOTE: I only tested this on mlx5; I have no access to the other hardware
for which I provided patches. Hopefully other folks can help test :)
Here's how it works when I test it on my mlx5 system:
$ ethtool -l eth4 | grep Combined | tail -1
Combined: 2
First, output the current NAPI settings:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump napi-get --json='{"ifindex": 7}'
[{'defer-hard-irqs': 0,
'gro-flush-timeout': 0,
'id': 345,
'ifindex': 7,
'irq': 527},
{'defer-hard-irqs': 0,
'gro-flush-timeout': 0,
'id': 344,
'ifindex': 7,
'irq': 327}]
Now, set the global sysfs parameters:
$ sudo bash -c 'echo 20000 >/sys/class/net/eth4/gro_flush_timeout'
$ sudo bash -c 'echo 100 >/sys/class/net/eth4/napi_defer_hard_irqs'
Output current NAPI settings again:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump napi-get --json='{"ifindex": 7}'
[{'defer-hard-irqs': 100,
'gro-flush-timeout': 20000,
'id': 345,
'ifindex': 7,
'irq': 527},
{'defer-hard-irqs': 100,
'gro-flush-timeout': 20000,
'id': 344,
'ifindex': 7,
'irq': 327}]
Now set NAPI ID 345, via its NAPI ID to specific values:
$ sudo ./tools/net/ynl/cli.py \
--spec Documentation/netlink/specs/netdev.yaml \
--do napi-set \
--json='{"id": 345,
"defer-hard-irqs": 111,
"gro-flush-timeout": 11111}'
None
Now output current NAPI settings again to ensure only NAPI ID 345
changed:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump napi-get --json='{"ifindex": 7}'
[{'defer-hard-irqs': 111,
'gro-flush-timeout': 11111,
'id': 345,
'ifindex': 7,
'irq': 527},
{'defer-hard-irqs': 100,
'gro-flush-timeout': 20000,
'id': 344,
'ifindex': 7,
'irq': 327}]
Now, increase gro-flush-timeout only:
$ sudo ./tools/net/ynl/cli.py \
--spec Documentation/netlink/specs/netdev.yaml \
--do napi-set --json='{"id": 345,
"gro-flush-timeout": 44444}'
None
Now output the current NAPI settings once more:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump napi-get --json='{"ifindex": 7}'
[{'defer-hard-irqs': 111,
'gro-flush-timeout': 44444,
'id': 345,
'ifindex': 7,
'irq': 527},
{'defer-hard-irqs': 100,
'gro-flush-timeout': 20000,
'id': 344,
'ifindex': 7,
'irq': 327}]
Now set NAPI ID 345 to have gro_flush_timeout of 0:
$ sudo ./tools/net/ynl/cli.py \
--spec Documentation/netlink/specs/netdev.yaml \
--do napi-set --json='{"id": 345,
"gro-flush-timeout": 0}'
None
Check that NAPI ID 345 has a value of 0:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump napi-get --json='{"ifindex": 7}'
[{'defer-hard-irqs': 111,
'gro-flush-timeout': 0,
'id': 345,
'ifindex': 7,
'irq': 527},
{'defer-hard-irqs': 100,
'gro-flush-timeout': 20000,
'id': 344,
'ifindex': 7,
'irq': 327}]
Change the queue count, ensuring that NAPI ID 345 retains its settings:
$ sudo ethtool -L eth4 combined 4
Check that the new queues have the system wide settings but that NAPI ID
345 remains unchanged:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump napi-get --json='{"ifindex": 7}'
[{'defer-hard-irqs': 100,
'gro-flush-timeout': 20000,
'id': 347,
'ifindex': 7,
'irq': 529},
{'defer-hard-irqs': 100,
'gro-flush-timeout': 20000,
'id': 346,
'ifindex': 7,
'irq': 528},
{'defer-hard-irqs': 111,
'gro-flush-timeout': 0,
'id': 345,
'ifindex': 7,
'irq': 527},
{'defer-hard-irqs': 100,
'gro-flush-timeout': 20000,
'id': 344,
'ifindex': 7,
'irq': 327}]
Now reduce the queue count below where NAPI ID 345 is indexed:
$ sudo ethtool -L eth4 combined 1
Check the output:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump napi-get --json='{"ifindex": 7}'
[{'defer-hard-irqs': 100,
'gro-flush-timeout': 20000,
'id': 344,
'ifindex': 7,
'irq': 327}]
Re-increase the queue count to ensure NAPI ID 345 is re-assigned the same
values:
$ sudo ethtool -L eth4 combined 2
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump napi-get --json='{"ifindex": 7}'
[{'defer-hard-irqs': 111,
'gro-flush-timeout': 0,
'id': 345,
'ifindex': 7,
'irq': 527},
{'defer-hard-irqs': 100,
'gro-flush-timeout': 20000,
'id': 344,
'ifindex': 7,
'irq': 327}]
Create new queues to ensure the sysfs globals are used for the new NAPIs
but that NAPI ID 345 is unchanged:
$ sudo ethtool -L eth4 combined 8
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump napi-get --json='{"ifindex": 7}'
[...]
{'defer-hard-irqs': 100,
'gro-flush-timeout': 20000,
'id': 346,
'ifindex': 7,
'irq': 528},
{'defer-hard-irqs': 111,
'gro-flush-timeout': 0,
'id': 345,
'ifindex': 7,
'irq': 527},
{'defer-hard-irqs': 100,
'gro-flush-timeout': 20000,
'id': 344,
'ifindex': 7,
'irq': 327}]
Last, but not least, let's try writing the sysfs parameters to ensure
all NAPIs are rewritten:
$ sudo bash -c 'echo 33333 >/sys/class/net/eth4/gro_flush_timeout'
$ sudo bash -c 'echo 222 >/sys/class/net/eth4/napi_defer_hard_irqs'
Check that worked:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
--dump napi-get --json='{"ifindex": 7}'
[...]
{'defer-hard-irqs': 222,
'gro-flush-timeout': 33333,
'id': 346,
'ifindex': 7,
'irq': 528},
{'defer-hard-irqs': 222,
'gro-flush-timeout': 33333,
'id': 345,
'ifindex': 7,
'irq': 527},
{'defer-hard-irqs': 222,
'gro-flush-timeout': 33333,
'id': 344,
'ifindex': 7,
'irq': 327}]
[1]: https://lore.kernel.org/20241009005525.13651-1-jdamato@fastly.com
v5: https://lore.kernel.org/20241009005525.13651-1-jdamato@fastly.com
rfcv4: https://lore.kernel.org/lkml/20241001235302.57609-1-jdamato@fastly.com
rfcv3: https://lore.kernel.org/20240912100738.16567-8-jdamato@fastly.com
rfcv2: https://lore.kernel.org/20240908160702.56618-1-jdamato@fastly.com
====================
Link: https://patch.msgid.link/20241011184527.16393-1-jdamato@fastly.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use netif_napi_add_config to assign persistent per-NAPI config when
initializing RX CQ NAPIs.
Presently, struct napi_config only has support for two fields used for
RX, so there is no need to support them with TX CQs, yet.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20241011184527.16393-10-jdamato@fastly.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use netif_napi_add_config to assign persistent per-NAPI config when
initializing NAPIs.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20241011184527.16393-9-jdamato@fastly.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use netif_napi_add_config to assign persistent per-NAPI config when
initializing NAPIs.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20241011184527.16393-8-jdamato@fastly.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support to set per-NAPI defer_hard_irqs and gro_flush_timeout.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241011184527.16393-7-jdamato@fastly.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a persistent NAPI config area for NAPI configuration to the core.
Drivers opt-in to setting the persistent config for a NAPI by passing an
index when calling netif_napi_add_config.
napi_config is allocated in alloc_netdev_mqs, freed in free_netdev
(after the NAPIs are deleted).
Drivers which call netif_napi_add_config will have persistent per-NAPI
settings: NAPI IDs, gro_flush_timeout, and defer_hard_irq settings.
Per-NAPI settings are saved in napi_disable and restored in napi_enable.
Co-developed-by: Martin Karsten <mkarsten@uwaterloo.ca>
Signed-off-by: Martin Karsten <mkarsten@uwaterloo.ca>
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241011184527.16393-6-jdamato@fastly.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support dumping gro_flush_timeout for a NAPI ID.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20241011184527.16393-5-jdamato@fastly.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allow per-NAPI gro_flush_timeout setting.
The existing sysfs parameter is respected; writes to sysfs will write to
all NAPI structs for the device and the net_device gro_flush_timeout
field. Reads from sysfs will read from the net_device field.
The ability to set gro_flush_timeout on specific NAPI instances will be
added in a later commit, via netdev-genl.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20241011184527.16393-4-jdamato@fastly.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support dumping defer_hard_irqs for a NAPI ID.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20241011184527.16393-3-jdamato@fastly.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add defer_hard_irqs to napi_struct in preparation for per-NAPI
settings.
The existing sysfs parameter is respected; writes to sysfs will write to
all NAPI structs for the device and the net_device defer_hard_irq field.
Reads from sysfs show the net_device field.
The ability to set defer_hard_irqs on specific NAPI instances will be
added in a later commit, via netdev-genl.
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20241011184527.16393-2-jdamato@fastly.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PHYs performing rate-matching using MAC-side flow-control always
perform duplex-matching as well in case they are supporting
half-duplex modes at all.
No longer remove half-duplex modes from their capabilities.
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/b157c0c289cfba024039a96e635d037f9d946745.1728617993.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Eric Dumazet says:
====================
tcp: add skb->sk to more control packets
Currently, TCP can set skb->sk for a variety of transmit packets.
However, packets sent on behalf of a TIME_WAIT sockets do not
have an attached socket.
Same issue for RST packets.
We want to change this, in order to increase eBPF program
capabilities.
This is slightly risky, because various layers could
be confused by TIME_WAIT sockets showing up in skb->sk.
v2: audited all sk_to_full_sk() users and addressed Martin feedback.
====================
Link: https://patch.msgid.link/20241010174817.1543642-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ip_send_unicast_reply() send orphaned 'control packets'.
These are RST packets and also ACK packets sent from TIME_WAIT.
Some eBPF programs would prefer to have a meaningful skb->sk
pointer as much as possible.
This means that TCP can now attach TIME_WAIT sockets to outgoing
skbs.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Brian Vazquez <brianvv@google.com>
Link: https://patch.msgid.link/20241010174817.1543642-6-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tcp_v6_send_response() send orphaned 'control packets'.
These are RST packets and also ACK packets sent from TIME_WAIT.
Some eBPF programs would prefer to have a meaningful skb->sk
pointer as much as possible.
This means that TCP can now attach TIME_WAIT sockets to outgoing
skbs.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Brian Vazquez <brianvv@google.com>
Link: https://patch.msgid.link/20241010174817.1543642-5-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This can be used to attach a socket to an skb,
taking a reference on sk->sk_refcnt.
This helper might be a NOP if sk->sk_refcnt is zero.
Use it from tcp_make_synack().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Brian Vazquez <brianvv@google.com>
Link: https://patch.msgid.link/20241010174817.1543642-4-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
TCP stack is not attaching skb to TIME_WAIT sockets yet,
but we would like to allow this in the future.
Add sk_listener_or_tw() helper to detect the three states
that FQ needs to take care.
Like NEW_SYN_RECV, TIME_WAIT are not full sockets and
do not contain sk->sk_pacing_status, sk->sk_pacing_rate.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Brian Vazquez <brianvv@google.com>
Link: https://patch.msgid.link/20241010174817.1543642-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
TCP will soon attach TIME_WAIT sockets to some ACK and RST.
Make sure sk_to_full_sk() detects this and does not return
a non full socket.
v3: also changed sk_const_to_full_sk()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Brian Vazquez <brianvv@google.com>
Link: https://patch.msgid.link/20241010174817.1543642-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch adds missing percpu_ref_exit when releasing percpu refs.
When releasing percpu refs, percpu_ref_exit should be called.
Otherwise, memory leak happens.
Fixes: 79a22238b4f2 ("net/smc: Use percpu ref for wr tx reference")
Signed-off-by: Kai Shen <KaiShen@linux.alibaba.com>
Reviewed-by: Dust Li <dust.li@linux.alibaba.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Link: https://patch.msgid.link/20241010115624.7769-1-KaiShen@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Address byte-order miss-matches flagged by Sparse.
In tg3_load_firmware_cpu() and tg3_get_device_address()
this is done using appropriate types to store big endian values.
In the cases of tg3_test_nvram(), where buf is an array which
contains values of several different types, cast to __le32
before converting values to host byte order.
Reported by Sparse as:
.../tg3.c:3745:34: warning: cast to restricted __be32
.../tg3.c:13096:21: warning: cast to restricted __le32
.../tg3.c:13096:21: warning: cast from restricted __be32
.../tg3.c:13101:21: warning: cast to restricted __le32
.../tg3.c:13101:21: warning: cast from restricted __be32
.../tg3.c:17070:63: warning: incorrect type in argument 3 (different base types)
.../tg3.c:17070:63: expected restricted __be32 [usertype] *val
.../tg3.c:17070:63: got unsigned int *
dr.../tg3.c:17071:63: warning: incorrect type in argument 3 (different base types)
.../tg3.c:17071:63: expected restricted __be32 [usertype] *val
.../tg3.c:17071:63: got unsigned int *
Also, address white-space issues on lines modified for the above.
And, for consistency, lines adjacent to them.
Compile tested only.
No functional change intended.
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241009-tg3-sparse-v1-1-6af38a7bf4ff@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jinjie Ruan says:
====================
posix-clock: Fix missing timespec64 check for PTP clock
Check timespec64 in pc_clock_settime() for PTP clock as
the man manual of clock_settime() said.
====================
Link: https://patch.msgid.link/20241009072302.1754567-1-ruanjinjie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since timespec64_valid() has been checked in higher layer
pc_clock_settime(), the duplicate check in lan743x_ptpci_settime64()
can be removed.
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20241009072302.1754567-3-ruanjinjie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As Andrew pointed out, it will make sense that the PTP core
checked timespec64 struct's tv_sec and tv_nsec range before calling
ptp->info->settime64().
As the man manual of clock_settime() said, if tp.tv_sec is negative or
tp.tv_nsec is outside the range [0..999,999,999], it should return EINVAL,
which include dynamic clocks which handles PTP clock, and the condition is
consistent with timespec64_valid(). As Thomas suggested, timespec64_valid()
only check the timespec is valid, but not ensure that the time is
in a valid range, so check it ahead using timespec64_valid_strict()
in pc_clock_settime() and return -EINVAL if not valid.
There are some drivers that use tp->tv_sec and tp->tv_nsec directly to
write registers without validity checks and assume that the higher layer
has checked it, which is dangerous and will benefit from this, such as
hclge_ptp_settime(), igb_ptp_settime_i210(), _rcar_gen4_ptp_settime(),
and some drivers can remove the checks of itself.
Cc: stable@vger.kernel.org
Fixes: 0606f422b453 ("posix clocks: Introduce dynamic clocks")
Acked-by: Richard Cochran <richardcochran@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://patch.msgid.link/20241009072302.1754567-2-ruanjinjie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As described in commit b07996c7abac ("sched_ext: Don't hold
scx_tasks_lock for too long"), we're doing a cond_resched() every 32
calls to scx_task_iter_next() to avoid RCU and other stalls. That commit
also added a cpu_relax() to the codepath where we drop and reacquire the
lock, but as Waiman described in [0], cpu_relax() should only be
necessary in busy loops to avoid pounding on a cacheline (or to allow a
hypertwin to more fully utilize a core).
Let's remove the unnecessary cpu_relax().
[0]: https://lore.kernel.org/all/35b3889b-904a-4d26-981f-c8aa1557a7c7@redhat.com/
Cc: Waiman Long <llong@redhat.com>
Signed-off-by: David Vernet <void@manifault.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
send_message() does not block in the MBOX implementation. This is
because the mailbox layer has its own queue. However, this confuses
the per xfer timeouts as they all start their timeout ticks in
parallel.
Consider a case where the xfer timeout is 30ms and a SCMI transaction
takes 25ms:
| 0ms: Message #0 is queued in mailbox layer and sent out, then sits
| at scmi_wait_for_message_response() with a timeout of 30ms
| 1ms: Message #1 is queued in mailbox layer but not sent out yet.
| Since send_message() doesn't block, it also sits at
| scmi_wait_for_message_response() with a timeout of 30ms
| ...
| 25ms: Message #0 is completed, txdone is called and message #1 is sent
| 31ms: Message #1 times out since the count started at 1ms. Even though
| it has only been inflight for 6ms.
Fixes: 5c8a47a5a91d ("firmware: arm_scmi: Make scmi core independent of the transport type")
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Message-Id: <20241014160717.1678953-1-justin.chen@broadcom.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
With the "drm/msm: add a display mmu fault handler" series [1] we saw
issues in the field where memory allocation was failing when
allocating space for registers in msm_disp_state_dump_regs().
Specifically we were seeing an order 5 allocation fail. It's not
surprising that order 5 allocations will sometimes fail after the
system has been up and running for a while.
There's no need here for contiguous memory. Change the allocation to
kvzalloc() which should make it much less likely to fail.
[1] https://lore.kernel.org/r/20240628214848.4075651-1-quic_abhinavk@quicinc.com/
Fixes: 98659487b845 ("drm/msm: add support to take dpu snapshot")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/619658/
Link: https://lore.kernel.org/r/20241014093605.2.I72441365ffe91f3dceb17db0a8ec976af8139590@changeid
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
If the allocation in msm_disp_state_dump_regs() failed then
`block->state` can be NULL. The msm_disp_state_print_regs() function
_does_ have code to try to handle it with:
if (*reg)
dump_addr = *reg;
...but since "dump_addr" is initialized to NULL the above is actually
a noop. The code then goes on to dereference `dump_addr`.
Make the function print "Registers not stored" when it sees a NULL to
solve this. Since we're touching the code, fix
msm_disp_state_print_regs() not to pointlessly take a double-pointer
and properly mark the pointer as `const`.
Fixes: 98659487b845 ("drm/msm: add support to take dpu snapshot")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/619657/
Link: https://lore.kernel.org/r/20241014093605.1.Ia1217cecec9ef09eb3c6d125360cc6c8574b0e73@changeid
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
When (mode->clock * 1000) is larger than (1<<31), int to unsigned long
conversion will sign extend the int to 64 bits and the pclk_rate value
will be incorrect.
Fix this by making the result of the multiplication unsigned.
Note that above (1<<32) would still be broken and require more changes, but
its unlikely anyone will need that anytime soon.
Fixes: c4d8cfe516dc ("drm/msm/dsi: add implementation for helper functions")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/618434/
Link: https://lore.kernel.org/r/20241007050157.26855-2-jonathan@marek.ca
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
drm_mode_vrefresh() can introduce a large rounding error, avoid it.
Fixes: 7c9e4a554d4a ("drm/msm/dsi: Reduce pclk rate for compression")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/618432/
Link: https://lore.kernel.org/r/20241007050157.26855-1-jonathan@marek.ca
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
The pll_cmp_to_fdata() was never used by the working code. Drop it to
prevent warnings with W=1 and clang.
Reported-by: Jani Nikula <jani.nikula@intel.com>
Closes: https://lore.kernel.org/dri-devel/3553b1db35665e6ff08592e35eb438a574d1ad65.1725962479.git.jani.nikula@intel.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Fixes: caedbf17c48d ("drm/msm: add msm8998 hdmi phy/pll support")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/615348/
Link: https://lore.kernel.org/r/20240922-msm-drop-unused-func-v1-1-c5dc083415b8@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
Make _dpu_crtc_setup_lm_bounds() check that CRTC width is not
overflowing LM requirements. Rename the function accordingly.
Fixes: 25fdd5933e4c ("drm/msm: Add SDM845 DPU support")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Tested-by: Abhinav Kumar <quic_abhinavk@quicinc.com> # sc7280
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/612237/
Link: https://lore.kernel.org/r/20240903-dpu-mode-config-width-v6-3-617e1ecc4b7a@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
Historically CRTC resources (LMs and CTLs) were assigned in
dpu_crtc_atomic_begin(). The commit 9222cdd27e82 ("drm/msm/dpu: move hw
resource tracking to crtc state") simply moved resources to
struct dpu_crtc_state, without changing the code sequence. Later on the
commit b107603b4ad0 ("drm/msm/dpu: map mixer/ctl hw blocks in encoder
modeset") rearanged the code, but still kept the cstate->num_mixers
assignment to happen during commit phase. This makes dpu_crtc_state
inconsistent between consequent atomic_check() calls.
Move CRTC resource assignment to happen at the end of
dpu_encoder_virt_atomic_check().
Fixes: b107603b4ad0 ("drm/msm/dpu: map mixer/ctl hw blocks in encoder modeset")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/612235/
Link: https://lore.kernel.org/r/20240903-dpu-mode-config-width-v6-2-617e1ecc4b7a@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
The commit b954fa6baaca ("drm/msm/dpu: Refactor rm iterator") removed
zero-init of the hw_ctl array, but didn't change the error condition,
that checked for hw_ctl[i] being NULL. At the same time because of the
early returns in case of an error dpu_encoder_phys might be left with
the resources assigned in the previous state. Rework assigning of hw_pp
/ hw_ctl to the dpu_encoder_phys in order to make sure they are always
set correctly.
Fixes: b954fa6baaca ("drm/msm/dpu: Refactor rm iterator")
Suggested-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/612233/
Link: https://lore.kernel.org/r/20240903-dpu-mode-config-width-v6-1-617e1ecc4b7a@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
|
|
Copying to a 16 byte structure into an 8-byte struct member
causes a compile-time warning:
| In file included from drivers/firmware/arm_ffa/driver.c:25:
| In function 'fortify_memcpy_chk',
| inlined from 'export_uuid' at include/linux/uuid.h:88:2,
| inlined from 'ffa_msg_send_direct_req2' at drivers/firmware/arm_ffa/driver.c:488:2:
| include/linux/fortify-string.h:571:25: error: call to '__write_overflow_field'
| declared with attribute warning: detected write beyond size of field
| (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
| __write_overflow_field(p_size_field, size);
Use a union for the conversion instead and make sure the byte order
is fixed in the process.
Fixes: aaef3bc98129 ("firmware: arm_ffa: Add support for FFA_MSG_SEND_DIRECT_{REQ,RESP}2")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Message-Id: <20240909110938.247976-1-arnd@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
A ring buffer which has its buffered mapped at boot up to fixed memory
should not be freed. Other buffers can be. The ref counting setup was
wrong for both. It made the not mapped buffers ref count have zero, and the
boot mapped buffer a ref count of 1. But an normally allocated buffer
should be 1, where it can be removed.
Keep the ref count of a normal boot buffer with its setup ref count (do
not decrement it), and increment the fixed memory boot mapped buffer's ref
count.
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Link: https://lore.kernel.org/20241011165224.33dd2624@gandalf.local.home
Fixes: e645535a954ad ("tracing: Add option to use memmapped memory for trace boot instance")
Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
