| Age | Commit message (Collapse) | Author |
|---|
|
The local bio_list may have pending bios when doing cleanup, it can
end up with memory leak if they don't get freed.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Don't populate the read-only array types on the stack, instead make
it static const. Makes the object code smaller by nearly 60 bytes:
Before:
text data bss dec hex filename
90536 6552 64 97152 17b80 fs/btrfs/ioctl.o
After:
text data bss dec hex filename
90414 6616 64 97094 17b46 fs/btrfs/ioctl.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Forward the correct return value -ENOMEM from btrfsic_dev_state_alloc()
too.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ adjust changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
We've seen the following backtrace stack in ftrace or dmesg log,
kworker/u16:10-4244 [000] 241942.480955: function: btrfs_put_ordered_extent
kworker/u16:10-4244 [000] 241942.480956: kernel_stack: <stack trace>
=> finish_ordered_fn (ffffffffa0384475)
=> btrfs_scrubparity_helper (ffffffffa03ca577) <-----"incorrect"
=> btrfs_freespace_write_helper (ffffffffa03ca98e) <-----"correct"
=> process_one_work (ffffffff81117b2f)
=> worker_thread (ffffffff81118c2a)
=> kthread (ffffffff81121de0)
=> ret_from_fork (ffffffff81d7087a)
btrfs_freespace_write_helper is actually calling normal_worker_helper
instead of btrfs_scrubparity_helper, so somehow kernel has parsed the
incorrect function address while unwinding the stack,
btrfs_scrubparity_helper really shouldn't be shown up.
It's caused by compiler doing inline for our helper function, adding a
noinline tag can fix that.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ use noinline_for_stack ]
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Since both committing transaction and writing log-tree are doing
plugging on metadata IO, we can unify to use %sync_writers to benefit
both cases, instead of checking bio_flags while writing meta blocks of
log-tree.
We can remove this bio_flags because in order to write dirty blocks,
log tree also uses btrfs_write_marked_extents(), inside which we
have enabled %sync_writers, therefore, every write goes in a
synchronous way, so does checksuming.
Please also note that, bio_flags is applied per-context while
%sync_writers is applied per-inode, so this might incur some overhead, ie.
1) while log tree is flushing its dirty blocks via
btrfs_write_marked_extents(), in which %sync_writers is increased
by one.
2) in the meantime, some writeback operations may happen upon btrfs's
metadata inode, so these writes go synchronously, too.
However, AFAICS, the overhead is not a big one while the win is that
we unify the two places that needs synchronous way and remove a
special hack/flag.
This removes the bio_flags related stuff for writing log-tree.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
We have started plug in btrfs_write_and_wait_marked_extents() but the
generated IOs actually go to device's schedule IO list where the work
is doing in another task, thus the started plug doesn't make any
sense.
And since we wait for IOs immediately after writing meta blocks, it's
the same case as writing log tree, doing sync submit can merge more
IOs.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Signed-off-by: Satoru Takeuchi <satoru.takeuchi@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
There are checks on fs_info in __btrfs_panic to avoid dereferencing a
null fs_info, however, there is a call to btrfs_crit that may also
dereference a null fs_info. Fix this by adding a check to see if fs_info
is null and only print the s_id if fs_info is non-null.
Detected by CoverityScan CID#401973 ("Dereference after null check")
Fixes: efe120a067c8 ("Btrfs: convert printk to btrfs_ and fix BTRFS prefix")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
The value of variable 'can_recover' is never used after being set, thus
it should be removed, as it was never used since the first commit
68a7342c51c95042 ("Btrfs: cleanup orphaned root orphan item").
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
If 'btrfs_alloc_path()' fails, we must free the resources already
allocated, as done in the other error handling paths in this function.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Qu Wenruo <quwenruo.btrfs@gmx.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
__link_block_group is called from only 2 places and at each call site the
space_info being passed is the same as the space info assigned to the passed
cache struct. Let's remove the redundant argument and make the function
reference the space_info from the passed block_group_cache. No functional
changes
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ renamed to link_block_group ]
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Currently the code executes add_extent_mapping and if it is successful
it links the new mapping, it then proceeds to unlock the extent mapping
tree and check for failure and handle them. Instead, rework the code to
only perform a single check if add_extent_mapping has failed and handle
it, otherwise the code continues in a linear fashion. No functional
changes
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Introduced by 5a5f79b57069 ("Btrfs: allow unaligned DIO") and never
used. The buffered fallback from unaligned DIO works as expected.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Timofey Titovets <nefelim4ag@gmail.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
btrfs_changed_cb_t represents the signature of the callback being passed
to btrfs_compare_trees. Currently there is only one such callback,
namely changed_cb in send.c. This function doesn't really uses the first
2 parameters, i.e. the roots. Since there are not other functions
implementing the btrfs_changed_cb_t let's remove the unused parameters
from the prototype and implementation.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
iterate_dir_item:found_key - introduced in 31db9f7c23fb ("Btrfs:
introduce BTRFS_IOC_SEND for btrfs send/receive"), yet never used.
record_ref:num - ditto
This is a first pass with the low-hanging fruit. There are still quite a
few unsued parameters in some function which have to abide by a callback
interface.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Src was initially part of 31ff1cd25d37 ("Btrfs: Copy into the log tree in
big batches"), however 16e7549f045d ("Btrfs: incompatible format change
to remove hole extents") changed parameters passed to copy_items which
made the src variable redundant.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Timofey Titovets <nefelim4ag@gmail.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
While we submit direct writes, if the inode is flagged with nodatasum,
there's no benefit to submit asynchronously, because
a) we don't have to calculate checksum across processors,
b) and direct IO has started a plug, but async submit makes us queue
IO on each device's scheduled IO list instead of DIO's plug list, so
that IOs get much less merges in general.
Lets use sync submit for nodatasum inodes.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
After mapping block with BTRFS_MAP_WRITE, parities have been sorted to
the end position, so this search can start from the first parity
stripe.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ copied changelog as a comment ]
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
We didn't copy fsid to struct super_block.s_uuid so Overlay disables
index feature with btrfs as the lower FS.
kernel: overlayfs: fs on '/lower' does not support file handles, falling back to index=off.
Fix this by publishing the fsid through struct super_block.s_uuid.
[ dsterba: I think that setting s_uuid is the last missing bit. Overlay
needs the file handle encoding support from the lower filesystem, which
is supported. Filling the whole filesystem id is correct, the subvolume
id is encoded in the file handle buffer from inside btrfs_encode_fh. ]
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
These aren't used outside of volumes.c.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
So that perf can show the state symbol.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Some static functions are needlessly forward declared. Let's remove those
declarations since they add no value.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Both wait_for_commit() and wait_for_writer() are checking the
condition out of the mutex lock.
This refactors code a bit to be lock safe.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Since TASK_UNINTERRUPTIBLE has been used here, wait_event() can do the
same job.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
If we're still going to wait after schedule(), we don't have to do
finish_wait() to remove our %wait_queue_entry since prepare_to_wait()
won't add the same %wait_queue_entry twice.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Block layer has a limit on plug, ie. BLK_MAX_REQUEST_COUNT == 16, so
we don't gain benefits by batching 64 bios here.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
This attempts to instill a bit of paranoia to the code dealing with
the CTO timer. It's believed that this will make the CTO timer more
robust in the case that we're having very long interrupt latencies.
Note that I originally thought that perhaps this patch was being
overly paranoid and wasn't really needed, but then while I was running
mmc_test on an rk3399 board I saw one instance of the message:
dwmmc_rockchip fe320000.dwmmc: Unexpected interrupt latency
I had debug prints in the CTO timer code and I found that it was
running CMD 13 at the time.
...so even though this patch seems like it might be overly paranoid,
maybe it really isn't?
Presumably the bad interrupt latency experienced was due to the fact
that I had serial console enabled as serial console is typically where
I place blame when I see absurdly large interrupt latencies. In this
particular case there was an (unrelated) printout to the serial
console just before I saw the "Unexpected interrupt latency" printout.
...and actually, I managed to even reproduce the problems by running
"iw mlan0 scan > /dev/null" while mmc_test was running. That not only
does a bunch of PCIe traffic but it also (on my system) outputs some
SELinux log spam.
Fixes: 03de19212ea3 ("mmc: dw_mmc: introduce timer for broken command transfer over scheme")
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In the commit 03de19212ea3 ("mmc: dw_mmc: introduce timer for broken
command transfer over scheme") we tried to calculate the expected
hardware command timeout value. Unfortunately that calculation isn't
quite correct in all cases. It used "bus_hz" but, as far as I can
tell, it's supposed to use the card clock. Let's account for the div
value, which is documented as 2x the value stored in the register, or
1 if the register is 0.
NOTE: It's not expected that this will actually fix anything important
since the 10 ms margin added by the function will pretty much dwarf
any calculations. The card clock should be 100 kHz at minimum and:
1000 ms/s * (255 * 2) / 100000 Hz.
Gives us 5.1 ms.
...so really the point of this patch is just to make the code more
"correct" in case anyone ever tries to remove the 10 ms buffer.
Fixes: 03de19212ea3 ("mmc: dw_mmc: introduce timer for broken command transfer over scheme")
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When running with the commit 03de19212ea3 ("mmc: dw_mmc: introduce
timer for broken command transfer over scheme") I found this message
in the log:
Unexpected command timeout, state 7
It turns out that we weren't properly cancelling the new CTO timer in
the case that a voltage switch was done. Let's promote the cancel
into the dw_mci_cmd_interrupt() function to fix this.
Fixes: 03de19212ea3 ("mmc: dw_mmc: introduce timer for broken command transfer over scheme")
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
mt2701/mt2712 has 12bit clock div, which is not compatible with
mt8135/mt8173. and, some additional features will be added in
mt2701/mt2712, so that need distinguish it by comatibale name.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Change the comptiable for support of multi-platform
Make compatible explicit, as MMC host of mt8173 has difference with
mt8135(mt8173 supports hs400 and hs400_tune),so that need separate
mt8173/mt8135 compatible name.
Add description for reg
Add description for source_cg
Add description for mediatek,latch-ck
Note that source_cg and mediatek,latch-ck are optional for some projects,
eg, MT2701 do not have source_cg, and MT2712 do not need
mediatek,latch-ck
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The following commit:
864c2357ca89 ("perf/core: Do not set cpuctx->cgrp for unscheduled cgroups")
made list_update_cgroup_event() skip setting cpuctx->cgrp if no cgroup event
targets %current's cgroup.
This breaks perf_event's hierarchical support because events which target one
of the ancestors get ignored.
Fix it by using cgroup_is_descendant() test instead of equality.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: David Carrillo-Cisneros <davidcc@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: kernel-team@fb.com
Cc: stable@vger.kernel.org # v4.9+
Fixes: 864c2357ca89 ("perf/core: Do not set cpuctx->cgrp for unscheduled cgroups")
Link: http://lkml.kernel.org/r/20171028164237.GA972780@devbig577.frc2.facebook.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
We keep PCI Ids in sdhci-pci.h and the O2-specific definitions belong in
sdhci-pci-o2micro.c. Move those definitions accordingly. Remove unused O2
definitions in sdhci-pci-core.c. The 3 o2micro external function
declarations might as well be in sdhci-pci.h as well, so move them there
and get rid of sdhci-pci-o2micro.h entirely.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Tidy Intel slot probe functions into one. A single function can be used
because the logic uses hid / uid as necessary to identify devices anyway.
This gets rid of some pointless comments and checks for variables that
cannot possibly be NULL, as well as giving the function a name that
identifies it as specific to Intel controllers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Make use of acpi_device_uid() instead of open coding.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Implement fallback compatibility strings for R-Car Gen 1, 2 and 3.
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, f.e. Gen 1 and 2. But beyond that its not clear what the relationship
between IP blocks might be. For example, I believe that r8a7790 is older
than r8a7791 but that doesn't imply that the latter is a descendant of the
former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme is being adopted for
drivers for Renesas SoCs.
Also, improve readability by listing the shmobile fallback compatibility
string after the more-specific compatibility strings they provide a
fallback for.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
strings
Add fallback compatibility strings for R-Car Gen 1, 2 and 3.
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, f.e. Gen 1 and 2. But beyond that its not clear what the relationship
between IP blocks might be. For example, I believe that r8a7790 is older
than r8a7791 but that doesn't imply that the latter is a descendant of the
former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme is being adopted for
drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Provide an example of the usage of the DT bindings for TMIO
in their documentation. The example given is for the r8a7790 (R-Car H2).
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Parse the new binding and store it in the host struct after doing some
sanity checks. The code is designed to support fixed SD driver type if
we ever need that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some boards may have to use a certain driver type (or drive strength) to
achieve stable eMMC communication. Describe a binding to set this up via
DT.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
