| Age | Commit message (Collapse) | Author |
|---|
|
responses
Driver has following initialization sequence for Target mode
1. Driver initialization starts
2. ISP Abort is scheduled when the target is enabled.
qla2xxx [0000:04:00.0]-4807:25: ISP abort scheduled
qla2xxx [0000:04:00.0]-00af:25: Performing ISP error recovery - ha=ffff880caa9e0000.
3. DPC thread starts the ISP Abort
4. While DPC is resetting the chip and initializing the firmware, we get
async events from the firmware about P2P mode, LOOP UP and PORT UPDATE.
5. PRLI from a initiator is delivered to us followed by a PLOGI and then a
SCSI command which creates a session.
6. If the SCSI command is a WRITE in this case, we issue XFR RDY and it
gets dropped as can be seen with messages RESET-XFR because ISP Abort
is still active
qla2xxx [0000:04:00.0]-e902:25: RESET-XFR active/old-count/new-count = 1/1/1.
7. If the SCSI command is a READ, we issue RESPONSE and they get dropped
as well because Abort is still active.
qla2xxx [0000:04:00.0]-e901:25: RESET-RSP active/old-count/new-count = 1/1/1
8. Now eventually, ISP Abort finishes clearing the DPC flags.
qla2xxx [0000:04:00.0]-8822:25: qla2x00_abort_isp succeeded.
qla2xxx [0000:04:00.0]-4808:25: ISP abort end.
9. Since we dropped SCSI commands silently (without any responses sent
to the initiator) initiator waits for a SCSI timeout (which is 60
seconds in our case), Sends an ABTS which fails since there
no se_cmd found for the tag that ABTS is referencing as the
commands were cleaned up in Step 6 and 7.
10. Initiator send an IO after the ABTS which succeed fine.
To fix the above case, the following changes have been made:
- To prevent target from dropping commands silently, use the online flag
instead to check for an active chip reset. Once the port is online during
a chip reset phase, we are good to process the commands.
- Clean up qla2x00_restart_isp to not set the online flag and process ATIO
as it is unnecessary. During a chip reset, interrupts are enabled only
after setting the online flag to 1, so ATIO's won't be missed and hence
no need to process ATIO's after setting the online flag.
Signed-off-by: Dilip Kumar Uppugandla <dilip@purestorage.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
set ATIO/Request/Response Queues and Default number
of outstanding command to 4k.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
99% of the time the ATIOQ has SCSI command. The other 1% of time
is something else. Most of the time this interrupt does not need
to hold the hardware_lock. We're moving the ATIO interrupt thread
to a different lock to reduce lock contention.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
queue work element to specific process lessen cache miss
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Register to receive notification of when irq setting change
occured.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Sessions management (add, deleted, modify) currently are serialized
through the hardware_lock. Hardware_lock is a high traffic lock.
This lock is accessed by both the transmit & receive sides.
Sessions management is now moved off to another lock call sess_lock.
This is done to reduce lock contention and increase traffic throughput.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Replace QLA_TGT_STATE_ABORTED state with a bit because
the current state of the command is lost when an abort
is requested by upper layer.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Until now ack'ing of a new PLOGI has only been delayed if there
was an existing session for the same WWN. Ack was released when
the session deletion completed.
If there was another WWN session with the same fc_id/loop_id pair
(aka "conflicting session"), PLOGI was still ack'ed immediately.
This potentially caused a problem when old session deletion logged
fc_id/loop_id out of FW after new session has been established.
Two work-arounds were attempted before:
1. Dropping PLOGIs until conflicting session goes away.
2. Detecting initiator being logged out of FW and issuing LOGO
to force re-login.
This patch introduces proper solution to the problem where PLOGI
is held until either existing session with same WWN or any
conflicting session goes away. Mechanism supports one session holding
two PLOGI acks as well as one PLOGI ack being held by many sessions.
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Acked-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
1. Initiator A is logged in with fc_id(1)/loop_id(1)
2. Initiator A re-logs in with fc_id(2)/loop_id(2)
3. Part of old session deletion async logoout for 1/1 is queued
4. Initiator B logs in with fc_id(1)/loop_id(1), starts
passing data and creates session.
5. Async logo from 3 is processed by DPC and sent to FW
Now initiator B has the session but is logged out from FW.
This condition is detected first with CTIO error 29 at which
point we should delete current session. During session
deletion we will send LOGO to initiator to force re-login.
Under rare circumstances initiator might be logged out of FW,
not have driver session, but still think it's logged in.
E.g. the above sequence plus session deletion due to re-config.
Incoming commands will fail to create local session because
initiator is not found in FW. In this case we also issue LOGO
to initiator to force him re-login.
Finally this patch fixes exchange leak when commands where
received in logged out state. In this case loop_id must be
set to FFFF when corresponding exchange is terminated. The
patch modifies exchange termination to always use FFFF,
since in certain scenarios it's impossible to tell whether
command was received in logged in or logged out state.
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Acked-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds interface to send explicit LOGO
explicit LOGO using using ELS commands from driver.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
DebugFS now will show fw_resource_count node.
FW Resource count
Original TGT exchg count[0]
current TGT exchg count[0]
original Initiator Exchange count[2048]
Current Initiator Exchange count[2048]
Original IOCB count[2078]
Current IOCB count[2067]
MAX VP count[254]
MAX FCF count[0]
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Following counters are added in target mode to help debugging efforts.
Target Counters
qla_core_sbt_cmd = 0
qla_core_ret_sta_ctio = 0
qla_core_ret_ctio = 0
core_qla_que_buf = 0
core_qla_snd_status = 0
core_qla_free_cmd = 0
num alloc iocb failed = 0
num term exchange sent = 0
num Q full sent = 0
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch enables Exchange offload support in Qlogic ISP.
To enable exchange offload with Qlogic ISP24XX/25XX/26XX,
set module parameter ql2xexchoffld to any non-zero number.
This will alow ISP firmware to store exchange data structures
used by firmware to host memory provided by driver. ISP firmware
can supports upto 32k total active exchanges.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch enables Extended Logins support in Qlogic ISP.
To enable extended login with Qlogic ISP24XX/25XX/26XX,
set module parameter ql2xexlogins to any non-zero number.
This will alow ISP firmware to store port database structure
information of remote login sessions to host memory provided
by driver. ISP firmware supports upto 16k total logins.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Now that we've added a 'trigger_async_request' knob to test the
request_firmware_nowait() API, let's use it. Also add tests for the
empty ("") string, since there have been a couple errors in that
handling already.
Since we now have real ways that the sysfs write might fail, let's add
the appropriate check on the 'echo' lines too.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
This patch fixes a bug writing to EEPROM in lan78xx_ethtool_set_eeprom()
when asked to write to OTP.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Neil Armstrong says:
====================
Add new capability and macb DT variant
The first patch introduces a new capability bit to disable usage of the
USRIO register on platform not implementing it thus avoiding some external
imprecise aborts on ARM based platforms.
The two last patchs adds a new macb variant compatible name using the
capability, the NP4 SoC uses this particular hardware configuration.
v1: http://lkml.kernel.org/r/1449485914-12883-1-git-send-email-narmstrong@baylibre.com
v2: http://lkml.kernel.org/r/1449582726-6148-1-git-send-email-narmstrong@baylibre.com
v3: http://lkml.kernel.org/r/1451898103-21868-1-git-send-email-narmstrong@baylibre.com
v4: http://lkml.kernel.org/r/1451900573-22657-1-git-send-email-narmstrong@baylibre.com
v5: switch SoC name to non-generic NP4 name
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add NP4 macb SoC variant.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Declare a new NP4 SoC variant having USRIO_DISABLED as capability bit.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some platforms, the macb integration does not use the USRIO
register to configure the (R)MII port and clocks.
When the register is not implemented and the MACB error signal
is connected to the bus error, reading or writing to the USRIO
register can trigger some Imprecise External Aborts on ARM platforms.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As of the 4.3 kernel release, the fitrim ioctl can now discard any region
of a disk that is not allocated to any chunk/block group, including the
first megabyte which is used for our primary superblock and by the boot
loader (grub for example).
Fix this by not allowing to trim/discard any region in the device starting
with an offset not greater than min(alloc_start_mount_option, 1Mb), just
as it was not possible before 4.3.
A reproducer test case for xfstests follows.
seq=`basename $0`
seqres=$RESULT_DIR/$seq
echo "QA output created by $seq"
tmp=/tmp/$$
status=1 # failure is the default!
trap "_cleanup; exit \$status" 0 1 2 3 15
_cleanup()
{
cd /
rm -f $tmp.*
}
# get standard environment, filters and checks
. ./common/rc
. ./common/filter
# real QA test starts here
_need_to_be_root
_supported_fs btrfs
_supported_os Linux
_require_scratch
rm -f $seqres.full
_scratch_mkfs >>$seqres.full 2>&1
# Write to the [0, 64Kb[ and [68Kb, 1Mb[ ranges of the device. These ranges are
# reserved for a boot loader to use (GRUB for example) and btrfs should never
# use them - neither for allocating metadata/data nor should trim/discard them.
# The range [64Kb, 68Kb[ is used for the primary superblock of the filesystem.
$XFS_IO_PROG -c "pwrite -S 0xfd 0 64K" $SCRATCH_DEV | _filter_xfs_io
$XFS_IO_PROG -c "pwrite -S 0xfd 68K 956K" $SCRATCH_DEV | _filter_xfs_io
# Now mount the filesystem and perform a fitrim against it.
_scratch_mount
_require_batched_discard $SCRATCH_MNT
$FSTRIM_PROG $SCRATCH_MNT
# Now unmount the filesystem and verify the content of the ranges was not
# modified (no trim/discard happened on them).
_scratch_unmount
echo "Content of the ranges [0, 64Kb] and [68Kb, 1Mb[ after fitrim:"
od -t x1 -N $((64 * 1024)) $SCRATCH_DEV
od -t x1 -j $((68 * 1024)) -N $((956 * 1024)) $SCRATCH_DEV
status=0
exit
Reported-by: Vincent Petry <PVince81@yahoo.fr>
Reported-by: Andrei Borzenkov <arvidjaar@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=109341
Fixes: 499f377f49f0 (btrfs: iterate over unused chunk space in FITRIM)
Cc: stable@vger.kernel.org # 4.3+
Signed-off-by: Filipe Manana <fdmanana@suse.com>
|
|
Commit e330eb86ba ("ARM: multi_v7_defconfig: enable Rockchip io-domain
driver") turns on a driver that was broken on 4.4-rc3 and fixed in 4.4-rc4.
This backmerges in the bugfix from mainline to keep the defconfig branch
testable by itself.
* commit 'd7b53fd9e37a':
drm/rockchip: vop: Correct enabled clocks during setup
drm/i915: Don't override output type for DDI HDMI
drm/i915: Don't compare has_drrs strictly in pipe config
drm/i915: Mark uneven memory banks on gen4 desktop as unknown swizzling
|
|
Pull drm nouveau fix from Dave Airlie:
"Still not back to work, but I decided to forward this fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/gr/nv40: fix oops in interrupt handler
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* bug fixes and improvements for firmware debug system (Golan and myself)
* fixes for D0i3 (Eliad)
* prevent muliple stations with the same MAC address
* advertise support for Rx A-MSDU in A-MPDU
* scan related fixes
* support -20.ucode
* fix WoWLAN for iwldvm
* preparations towards multiple Rx queues
* platform power improvements for GO mode when no clients are associated
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- Two build issues, one in the ipmmu-vmsa driver and one for the new
generic dma-api implemention used on arm64
- A performance fix for said dma-api implemention
- An issue caused by a wrong offset in map_sg in the same code as above
* tag 'iommu-fixes-v4.4-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/dma: Use correct offset in map_sg
iommu/ipmmu-vmsa: Don't truncate ttbr if LPAE is not enabled
iommu/dma: Avoid unlikely high-order allocations
iommu/dma: Add some missing #includes
|
|
We hit ftrace_bug report when booting Android on a 64bit ATOM SOC chip.
Basically, there is a race between insmod and ftrace_run_update_code.
After load_module=>ftrace_module_init, another thread jumps in to call
ftrace_run_update_code=>ftrace_arch_code_modify_prepare
=>set_all_modules_text_rw, to change all modules
as RW. Since the new module is at MODULE_STATE_UNFORMED, the text attribute
is not changed. Then, the 2nd thread goes ahead to change codes.
However, load_module continues to call complete_formation=>set_section_ro_nx,
then 2nd thread would fail when probing the module's TEXT.
The patch fixes it by using notifier to delay the enabling of ftrace
records to the time when module is at state MODULE_STATE_COMING.
Link: http://lkml.kernel.org/r/567CE628.3000609@intel.com
Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com>
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
No major changes to list.
|
|
The kerneldoc for request_firmware_nowait() says that it may call the
provided cont() callback with @fw == NULL, if the firmware request
fails. However, this is not the case when called with an empty string
(""). This case is short-circuited by the 'name[0] == '\0'' check
introduced in commit 471b095dfe0d ("firmware_class: make sure fw requests
contain a name"), so _request_firmware() never gets to set the fw to
NULL.
Noticed while using the new 'trigger_async_request' testing hook:
# printf '\x00' > /sys/devices/virtual/misc/test_firmware/trigger_async_request
[10553.726178] test_firmware: loading ''
[10553.729859] test_firmware: loaded: 995209091
# printf '\x00' > /sys/devices/virtual/misc/test_firmware/trigger_async_request
[10733.676184] test_firmware: loading ''
[10733.679855] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[10733.687951] pgd = ec188000
[10733.690655] [00000004] *pgd=00000000
[10733.694240] Internal error: Oops: 5 [#1] SMP ARM
[10733.698847] Modules linked in: btmrvl_sdio btmrvl bluetooth sbs_battery nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter ip6_tables asix usbnet mwifiex_sdio mwifiex cfg80211 jitterentropy_rng drbg joydev snd_seq_midi snd_seq_midi_event snd_rawmidi snd_seq snd_seq_device ppp_async ppp_generic slhc tun
[10733.725670] CPU: 0 PID: 6600 Comm: bash Not tainted 4.4.0-rc4-00351-g63d0877 #178
[10733.733137] Hardware name: Rockchip (Device Tree)
[10733.737831] task: ed24f6c0 ti: ee322000 task.ti: ee322000
[10733.743222] PC is at do_raw_spin_lock+0x18/0x1a0
[10733.747831] LR is at _raw_spin_lock+0x18/0x1c
[10733.752180] pc : [<c00653a0>] lr : [<c054c204>] psr: a00d0013
[10733.752180] sp : ee323df8 ip : ee323e20 fp : ee323e1c
[10733.763634] r10: 00000051 r9 : b6f18000 r8 : ee323f80
[10733.768847] r7 : c089cebc r6 : 00000001 r5 : 00000000 r4 : ec0e6000
[10733.775360] r3 : dead4ead r2 : c06bd140 r1 : eef913b4 r0 : 00000000
[10733.781874] Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[10733.788995] Control: 10c5387d Table: 2c18806a DAC: 00000051
[10733.794728] Process bash (pid: 6600, stack limit = 0xee322218)
[10733.800549] Stack: (0xee323df8 to 0xee324000)
[10733.804896] 3de0: ec0e6000 00000000
[10733.813059] 3e00: 00000001 c089cebc ee323f80 b6f18000 ee323e2c ee323e20 c054c204 c0065394
[10733.821221] 3e20: ee323e44 ee323e30 c02fec60 c054c1f8 ec0e7ec0 ec3fcfc0 ee323e5c ee323e48
[10733.829384] 3e40: c02fed08 c02fec48 c07dbf74 eeb05a00 ee323e8c ee323e60 c0253828 c02fecac
[10733.837547] 3e60: 00000001 c0116950 ee323eac ee323e78 00000001 ec3fce00 ed2d9700 ed2d970c
[10733.845710] 3e80: ee323e9c ee323e90 c02e873c c02537d4 ee323eac ee323ea0 c017bd40 c02e8720
[10733.853873] 3ea0: ee323ee4 ee323eb0 c017b250 c017bd00 00000000 00000000 f3e47a54 ec128b00
[10733.862035] 3ec0: c017b10c ee323f80 00000001 c000f504 ee322000 00000000 ee323f4c ee323ee8
[10733.870197] 3ee0: c011b71c c017b118 ee323fb0 c011bc90 becfa8d9 00000001 ec128b00 00000001
[10733.878359] 3f00: b6f18000 ee323f80 ee323f4c ee323f18 c011bc90 c0063950 ee323f3c ee323f28
[10733.886522] 3f20: c0063950 c0549138 00000001 ec128b00 00000001 ec128b00 b6f18000 ee323f80
[10733.894684] 3f40: ee323f7c ee323f50 c011bed8 c011b6ec c0135fb8 c0135f24 ec128b00 ec128b00
[10733.902847] 3f60: 00000001 b6f18000 c000f504 ee322000 ee323fa4 ee323f80 c011c664 c011be24
[10733.911009] 3f80: 00000000 00000000 00000001 b6f18000 b6e79be0 00000004 00000000 ee323fa8
[10733.919172] 3fa0: c000f340 c011c618 00000001 b6f18000 00000001 b6f18000 00000001 00000000
[10733.927334] 3fc0: 00000001 b6f18000 b6e79be0 00000004 00000001 00000001 8068a3f1 b6e79c84
[10733.935496] 3fe0: 00000000 becfa7dc b6de194d b6e20246 400d0030 00000001 7a4536e8 49bda390
[10733.943664] [<c00653a0>] (do_raw_spin_lock) from [<c054c204>] (_raw_spin_lock+0x18/0x1c)
[10733.951743] [<c054c204>] (_raw_spin_lock) from [<c02fec60>] (fw_free_buf+0x24/0x64)
[10733.959388] [<c02fec60>] (fw_free_buf) from [<c02fed08>] (release_firmware+0x68/0x74)
[10733.967207] [<c02fed08>] (release_firmware) from [<c0253828>] (trigger_async_request_store+0x60/0x124)
[10733.976501] [<c0253828>] (trigger_async_request_store) from [<c02e873c>] (dev_attr_store+0x28/0x34)
[10733.985533] [<c02e873c>] (dev_attr_store) from [<c017bd40>] (sysfs_kf_write+0x4c/0x58)
[10733.993437] [<c017bd40>] (sysfs_kf_write) from [<c017b250>] (kernfs_fop_write+0x144/0x1a8)
[10734.001689] [<c017b250>] (kernfs_fop_write) from [<c011b71c>] (__vfs_write+0x3c/0xe4)
After this patch:
# printf '\x00' > /sys/devices/virtual/misc/test_firmware/trigger_async_request
[ 32.126322] test_firmware: loading ''
[ 32.129995] test_firmware: failed to async load firmware
-bash: printf: write error: No such device
Fixes: 471b095dfe0d ("firmware_class: make sure fw requests contain a name")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
We might want to test for bugs like that found in commit f9692b2699bd
("firmware: fix possible use after free on name on asynchronous
request"), where the asynchronous request API had race conditions.
Let's add a simple file that will launch the async request, then wait
until it's complete and report the status. It's not a true async test
(we're using a mutex + wait_for_completion(), so we can't get more than
one going at the same time), but it does help make sure the basic API is
sane, and it can catch some class of bugs.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
We're essentially just doing an open-coded kstrndup(). The only
differences are with what happens after the first '\0' character, but
request_firmware() doesn't care about that.
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace fix from Steven Rostedt:
"PeiyangX Qiu reported that if a module fails to load between calling
ftrace_module_init() and do_init_module() that the allocations made in
ftrace_module_init() will not be freed, resulting in a memory leak.
The solution is to call ftrace_release_mod() on the failing module in
the fail path befor do_init_module() is called. This will remove any
allocations made for that module, and nothing if ftrace_module_init()
wasn't called yet for that module.
Note, once do_init_module() is called, the MODULE_GOING notifiers are
called for the failed module, which calls into the ftrace code to do
the proper clean up (basically calling ftrace_release_mod())"
* tag 'trace-v4.4-rc4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace/module: Call clean up function when module init fails early
|
|
request_firmware() failures currently won't get reported at all (the
error code is discarded). What's more, we get confusing messages, like:
# echo -n notafile > /sys/devices/virtual/misc/test_firmware/trigger_request
[ 8280.311856] test_firmware: loading 'notafile'
[ 8280.317042] test_firmware: load of 'notafile' failed: -2
[ 8280.322445] test_firmware: loaded: 0
# echo $?
0
Report the failures via write() errors, and don't say we "loaded"
anything.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
The casting was done incorrectly for 32-bit builds. Fixed to use uintptr_t.
Reported-by: Eric Adams <adamse@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
Qiu Peiyang pointed out that there's a race when enabling function tracing
and loading a module. In order to make the modifications of converting nops
in the prologue of functions into callbacks, the text needs to be converted
from read-only to read-write. When enabling function tracing, the text
permission is updated, the functions are modified, and then they are put
back.
When loading a module, the updates to convert function calls to mcount is
done before the module text is set to read-only. But after it is done, the
module text is visible by the function tracer. Thus we have the following
race:
CPU 0 CPU 1
----- -----
start function tracing
set text to read-write
load_module
add functions to ftrace
set module text read-only
update all functions to callbacks
modify module functions too
< Can't it's read-only >
When this happens, ftrace detects the issue and disables itself till the
next reboot.
To fix this, a new DISABLED flag is added for ftrace records, which all
module functions get when they are added. Then later, after the module code
is all set, the records will have the DISABLED flag cleared, and they will
be enabled if any callback wants all functions to be traced.
Note, this doesn't add the delay to later. It simply changes the
ftrace_module_init() to do both the setting of DISABLED records, and then
immediately calls the enable code. This helps with testing this new code as
it has the same behavior as previously. Another change will come after this
to have the ftrace_module_enable() called after the text is set to
read-only.
Cc: Qiu Peiyang <peiyangx.qiu@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Signed-off-by: Yuan Sun <sunyuan3@huawei.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
Signed-off-by: Yuan Sun <sunyuan3@huawei.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
Signed-off-by: Yuan Sun <sunyuan3@huawei.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
Signed-off-by: Yuan Sun <sunyuan3@huawei.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
|
|
Commit d699ed250c07 ("mtd: nand: make use of
nand_set/get_controller_data() helpers") overlooked some uses of
nand_chip::priv.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
As of commit 2d3b77bac34b ("mtd: nand: update mtd_to_nand()"), this
assignment isn't necessary, since struct mtd_info is embedded in struct
nand_chip.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: Alex Smith <alex@alex-smith.me.uk>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Before:
$ perf test -v cqm
48: Test intel cqm nmi context read :
--- start ---
test child forked, pid 1681
parse_events failed
test child finished with -2
---- end ----
Test intel cqm nmi context read: Skip
$
After:
$ perf test -v cqm
48: Test intel cqm nmi context read :
--- start ---
test child forked, pid 1681
parse_events failed, is "intel_cqm/llc_occupancy/" available?
test child finished with -2
---- end ----
Test intel cqm nmi context read: Skip
$
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-eidpiv5x4nkbsx37xwikbnir@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
We were asking for a 4kHz sample_freq, making the test fail needlessly
when the system reduced /proc/sys/kernel/perf_event_max_sample_rate
below that.
Before:
# perf test -vv dummy
23: Test using a dummy software event to keep tracking :
--- start ---
test child forked, pid 32421
------------------------------------------------------------
perf_event_attr:
type 1
size 112
config 0x9
{ sample_period, sample_freq } 4000
sample_type IP|TID|ID|PERIOD
<SNIP>
sys_perf_event_open failed, error -22
Unable to open dummy and cycles event
test child finished with -2
---- end ----
Test using a dummy software event to keep tracking: Skip
#
[root@zoo ~]# cat /proc/sys/kernel/perf_event_max_sample_rate
1000
After:
[root@zoo ~]# perf test dummy
23: Test using a dummy software event to keep tracking : Ok
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-487iquegrs2379e5n0pi0tcp@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Fixing this problem, introduced recently:
$ perf test python
16: Try 'import perf' in python, checking link problems : FAILED!
In verbose mode we find out what is missing:
$ perf test -v python
16: Try 'import perf' in python, checking link problems :
--- start ---
test child forked, pid 24894
Traceback (most recent call last):
File "<stdin>", line 1, in <module>
ImportError: /tmp/build/perf/python/perf.so: undefined symbol: find_next_bit
test child finished with -1
---- end ----
Try 'import perf' in python, checking link problems: FAILED!
$
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Fixes: f77b57ad4fc4 ("perf cpu_map: Add cpu_map__new_event function")
Link: http://lkml.kernel.org/n/tip-rajx0zkz6czdrnvvwf0jp76p@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Andrew Lunn says:
====================
Support MDIO devices
The discussions about changing the way DSA probes switches resulted in
the wish to have switches attached to an MDIO bus to be represented as
an MDIO device. However the current code only supports PHYs on MDIO
busses. This patchset remedies this problem. It consists of a number
of cleanups, abstraction for accessing structure members, and
refactoring, as well as adding the concept of a generic MDIO device
and MDIO driver.
v2:
Added Reviewed-by from Florian
Made phydev_name() an inline function
Added phy_attached_info/phy_attached_print() for information about
the attached phy.
Removed now redundant irq setup from of_mdio.c
Dropped hunks from PHYMII ioctl which prevented access to any address
DSA carrier off before phy setup
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make device_free and device_remove operations in the mdio device
structure, so the core code does not need to differentiate between
phy devices and generic mdio devices.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not all devices on an MDIO bus are PHYs. Meaning not all MDIO drivers
are PHY drivers. Add support for generic MDIO drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make it clear that mdiobus_scan () will only find devices which have a
vendor/product ID in registers 2 and 3. These are typically PHY
devices. Other sort of MDIO devices, such as switches, are not
expected to be found during the scan.
Similarly, __mdiobus_register(), which calls mdiobus_scan() will only
find PHY devices, and other sorts of MDIO devices are expected to be
instantiated from device tree.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function should work with any sort of MDIO device which can be
probed on the bus, not just PHY devices. So generalise it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Matching a driver to a device has both generic parts, and parts which
are specific to PHY devices. Move the PHY specific parts into
phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
