summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2011-10-14rtlwifi: rtl8192ce: Add new chip revisionsChaoming Li
This patch incorporate the differences between the 06/20/2011 and 08/16/2011 Realtek releases of the rtlwifi driver. The changes include: 1. Adding new chip revisions including new firmware. Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14rtlwifi: Update to new Realtek version - Part IChaoming Li
This patch incorporate the differences between the 06/20/2011 and 08/16/2011 Realtek releases of the rtlwifi driver. The changes include: 1. Handling of IEEE80211_HW_CONNECTION_MONITOR. 2. Fix typo to get proper response to nullfunc frames. Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14rtlwifi: Change PCI drivers to use the new PM frameworkLarry Finger
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14mac80211: Populate radiotap header with MCS info for TX framesHelmut Schaa
mac80211 already filled in the MCS rate info for rx'ed frames but tx'ed frames that are sent to a monitor interface during the status callback lack this information. Add the radiotap fields for MCS info to ieee80211_tx_status_rtap_hdr and populate them when sending tx'ed frames to the monitors. The needed headroom is only extended by one byte since we don't include legacy rate information in the rtap header for HT frames. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14mac80211: Build TX radiotap header dynamicallyHelmut Schaa
Get rid of the ieee80211_tx_status_rtap_hdr struct and instead build the rtap header dynamically. This makes it easier to extend the rtap header generation in the future. Add ieee80211_tx_radiotap_len to calculate the expected size of the rtap header before generating it. Since we can't check if the rtap header fits into the requested headroom during compile time anymore add a WARN_ON_ONCE. Also move the actual rtap header generation into its own function. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: add missing include to iwl-agn-rs.hEmmanuel Grumbach
A few were missing Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: remove uneeded include to iwl-dev.hEmmanuel Grumbach
iwl-core.c and iwl-trans-pcie-tx.c don't need to include iwl-dev.h Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: move iwl_enable_rfkill_int and kill iwl-helpers.hEmmanuel Grumbach
Move iwl_enable_rfkill_int to iwl-core.h, and remove the empty iwl-helpers.h Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: move iwl_beacon_time_mask_XXX near to usageEmmanuel Grumbach
Since iwl_beacon_time_mask_[high,low] are used in iwl-core.c only, move them to there. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: remove 6000 hw headerJohannes Berg
The constants can be moved together with the similar ones for other devices and we can then remove the file. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: remove 5000 hw headerJohannes Berg
The inline function in this header is only used in a single file, so we can move it there. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: rename iwl-rx.c to iwl-agn-rx.cWey-Yi Guy
After driver split, there were no shared functions between agn and legacy; rename iwl-rx.c to iwl-agn-rx.c Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: merge station management functionsWey-Yi Guy
After driver split, no need to separate station management functions in two files, merge it Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: rename all the mac80211 callback functionsWey-Yi Guy
Use the same calling style for all the mac80211 callback functions Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: add debug for mac80211 callbackWey-Yi Guy
Add IWL_DEBUG_MAC80211 debug for all mac80211 callback function Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: don't stop rts/cts until last aggregation queue closeWey-Yi Guy
Once enable rts/cts for aggregation queue, do not disable until the last aggregation queue closed. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: more info on warning for shutdown agg queueWey-Yi Guy
When detect wrong state on shutdown aggregation queue, show more information for debugging Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlwifi: update comments on how to enable debug flagWey-Yi Guy
Modify comments on how to enable and change debug_level Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: use low retry limit for WoWLANWey-Yi Guy
When in D3 state, use low retry limit for both data and rts Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: do nothing when disable agg in wrong stateWey-Yi Guy
When disable aggregation request come in on wrong agg state. ignore it Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: warn only once if AGG state is wrongEmmanuel Grumbach
This one can be _very_ noisy. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: fix a race in the unmapping of the TFDsEmmanuel Grumbach
While inspecting the code, I saw that iwl_tx_queue_unmap modifies the read pointer of the Tx queue without taking any locks. This means that it can race with the reclaim flow. This can possibly lead to a DMA warning complaining that we unmap the same buffer twice. This is more a W/A than a fix since it is really weird to take sta_lock inside iwl_tx_queue_unmap, but it can help until we revamp the locking model in the transport layer. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: Add "_d" sku to 105 series of devicesWey-Yi Guy
Add additional sku to 105 series Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: add "_d" sku to 6005 series of devicesWey-Yi Guy
Add additional sku to 6005 series of devices Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: set rts retry limitWey-Yi Guy
setup the rts rety limit for tx command Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: remove un-necessary stepWey-Yi Guy
No need to copy twice. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: stop interrupts when suspendingJohannes Berg
Occasionally, the device will send interrupts while it is resuming, at a point where we are not set up again to handle them. This causes the core IRQ handling to completely disable the IRQ, and then the driver won't work again until it is reloaded/rebound. To fix this issue disable the IRQ on suspend, this will cause us to only get interrupts again after we've setup everything on resume. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: eliminate bus pointer from iwl_priv structureDon Fry
A pointer to the bus structure is still in iwl_priv. Finish cleanup and remove it. Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: kill hw_params.max_stationsEmmanuel Grumbach
Not needed since driver split. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: send simple LQ command for WoWLANJohannes Berg
For some reason, WoWLAN doesn't always seem to be happy with more advanced LQ commands. Since we don't need them as we're not going to send a lot of data, simply program the station with the very simple default LQ command. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: don't assign seqno to QoS Null framesJohannes Berg
802.11 says: "Sequence numbers for QoS (+)Null frames may be set to any value." However, if we use the normal counters then peers will get confused with aggregation since there'll be holes in the sequence number sequence. To avoid that, don't assign sequence numbers to QoS Null frames. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi GUy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: update beacon smarterJohannes Berg
Updating the beacon every time right after one was transmitted is pointless, most of the time we might not even have to update it. We will update it every time it changes, which includes from set_tim(), a callback iwlwifi didn't implement so far. This also reduces latency for clients, previously we would update the beacon right after the previous one was transmitted, and then a TIM change would only take effect after that again -- updating the beacon right after the TIM changes makes the TIM change go out to the air faster. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: add "echo test" command to debugfsWey-Yi Guy
For command queue testing, add "echo test" to debugfs Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: check rf kill in queue stuckWey-Yi Guy
check the RF KILL flag in queue stuck watch dog function Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: add "echo" test when command queue stuckWey-Yi Guy
When detect command queue stuck, instead of reload the firmware do the "echo" test to make sure it is really stuck before reload Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: add WARN if tx cmd complete come back lateWey-Yi Guy
For error condition, STATUS_HCMD_ACTIVE already got clear before receive tx cmd complete, give warning Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: add REPLY_ECHO host commandWey-Yi Guy
Add "echo" host command for testing and drebugging to make sure uCode still responding Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14iwlagn: add cmd queue pointer info when timeoutWey-Yi Guy
When detect cmd queue time out, display the current read/write pointer Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-14Bluetooth: rfcomm: Fix sleep in invalid context in rfcomm_security_cfmSzymon Janc
This was triggered by turning off encryption on ACL link when rfcomm was using high security. rfcomm_security_cfm (which is called from rx task) was closing DLC and this involves sending disconnect message (and locking socket). Move closing DLC to rfcomm_process_dlcs and only flag DLC for closure in rfcomm_security_cfm. BUG: sleeping function called from invalid context at net/core/sock.c:2032 in_atomic(): 1, irqs_disabled(): 0, pid: 1788, name: kworker/0:3 [<c0068a08>] (unwind_backtrace+0x0/0x108) from [<c05e25dc>] (dump_stack+0x20/0x24) [<c05e25dc>] (dump_stack+0x20/0x24) from [<c0087ba8>] (__might_sleep+0x110/0x12c) [<c0087ba8>] (__might_sleep+0x110/0x12c) from [<c04801d8>] (lock_sock_nested+0x2c/0x64) [<c04801d8>] (lock_sock_nested+0x2c/0x64) from [<c05670c8>] (l2cap_sock_sendmsg+0x58/0xcc) [<c05670c8>] (l2cap_sock_sendmsg+0x58/0xcc) from [<c047cf6c>] (sock_sendmsg+0xb0/0xd0) [<c047cf6c>] (sock_sendmsg+0xb0/0xd0) from [<c047cfc8>] (kernel_sendmsg+0x3c/0x44) [<c047cfc8>] (kernel_sendmsg+0x3c/0x44) from [<c056b0e8>] (rfcomm_send_frame+0x50/0x58) [<c056b0e8>] (rfcomm_send_frame+0x50/0x58) from [<c056b168>] (rfcomm_send_disc+0x78/0x80) [<c056b168>] (rfcomm_send_disc+0x78/0x80) from [<c056b9f4>] (__rfcomm_dlc_close+0x2d0/0x2fc) [<c056b9f4>] (__rfcomm_dlc_close+0x2d0/0x2fc) from [<c056bbac>] (rfcomm_security_cfm+0x140/0x1e0) [<c056bbac>] (rfcomm_security_cfm+0x140/0x1e0) from [<c0555ec0>] (hci_event_packet+0x1ce8/0x4d84) [<c0555ec0>] (hci_event_packet+0x1ce8/0x4d84) from [<c0550380>] (hci_rx_task+0x1d0/0x2d0) [<c0550380>] (hci_rx_task+0x1d0/0x2d0) from [<c009ee04>] (tasklet_action+0x138/0x1e4) [<c009ee04>] (tasklet_action+0x138/0x1e4) from [<c009f21c>] (__do_softirq+0xcc/0x274) [<c009f21c>] (__do_softirq+0xcc/0x274) from [<c009f6c0>] (do_softirq+0x60/0x6c) [<c009f6c0>] (do_softirq+0x60/0x6c) from [<c009f794>] (local_bh_enable_ip+0xc8/0xd4) [<c009f794>] (local_bh_enable_ip+0xc8/0xd4) from [<c05e5804>] (_raw_spin_unlock_bh+0x48/0x4c) [<c05e5804>] (_raw_spin_unlock_bh+0x48/0x4c) from [<c040d470>] (data_from_chip+0xf4/0xaec) [<c040d470>] (data_from_chip+0xf4/0xaec) from [<c04136c0>] (send_skb_to_core+0x40/0x178) [<c04136c0>] (send_skb_to_core+0x40/0x178) from [<c04139f4>] (cg2900_hu_receive+0x15c/0x2d0) [<c04139f4>] (cg2900_hu_receive+0x15c/0x2d0) from [<c0414cb8>] (hci_uart_tty_receive+0x74/0xa0) [<c0414cb8>] (hci_uart_tty_receive+0x74/0xa0) from [<c02cbd9c>] (flush_to_ldisc+0x188/0x198) [<c02cbd9c>] (flush_to_ldisc+0x188/0x198) from [<c00b2774>] (process_one_work+0x144/0x4b8) [<c00b2774>] (process_one_work+0x144/0x4b8) from [<c00b2e8c>] (worker_thread+0x198/0x468) [<c00b2e8c>] (worker_thread+0x198/0x468) from [<c00b9bc8>] (kthread+0x98/0xa0) [<c00b9bc8>] (kthread+0x98/0xa0) from [<c0061744>] (kernel_thread_exit+0x0/0x8) Signed-off-by: Szymon Janc <szymon.janc@tieto.com> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
2011-10-14pata_efar: fix register naming used in efar_set_piomode()Bartlomiej Zolnierkiewicz
Rename 'idetm_port' and 'idetm_data' variables to 'master_port' and 'master_data' respectively to match register naming used in efar_set_dmamode() and in ata_piix.c. Fix efar_set_piomode() documentation while at it. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-10-14pata_rdc: add Power Management supportBartlomiej Zolnierkiewicz
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-10-14ata_piix: unify code for programming PIO and MWDMA timingsBartlomiej Zolnierkiewicz
Besides making things noticably simpler it results in ~2% decrease in the driver LOC count and also ~2% decrease in the driver binary size (as measured on x86-32). Fix piix_set_piomode() documentation while at it. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-10-14ata_piix: SITRE handling fixBartlomiej Zolnierkiewicz
Set SITRE (separate slave timing register) bit also in master-only configurations to match other PIIX-alike drivers and make further changes easier. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-10-14libata: make ata_sff_data_xfer_noirq() work with 32-bit PIOBartlomiej Zolnierkiewicz
Always use ata_sff_data_xfer32() in ata_sff_data_xfer_noirq() so the latter can be also used for host controllers supporting 32-bit PIO operations. It is a completely safe thing to do because if 32-bit PIO is not supported or enabled ata_sff_data_xfer32() will fallback to a standard method. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-10-14pata_artop: add Power Management supportBartlomiej Zolnierkiewicz
Fixes IDE -> libata regression. There shouldn't be any problems with it as corresponding IDE's host driver (aec62xx) has been supporting PCI Power Management since Oct 10 2008 (commit feb22b7f "ide: add proper PCI PM support (v2)") and IDE PM since Jun 14 2003 (patch v2.5.73 "ide: Power Management"). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-10-14pata_sl82c105: add Power Management supportBartlomiej Zolnierkiewicz
Fixes IDE -> libata regression. There shouldn't be any problems with it as corresponding IDE's host driver (sl82c105) has been supporting PCI Power Management since Oct 10 2008 (commit feb22b7f "ide: add proper PCI PM support (v2)") and IDE PM since Jun 14 2003 (patch v2.5.73 "ide: Power Management"). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-10-14pata_pdc2027x: add Power Management supportBartlomiej Zolnierkiewicz
Fixes IDE -> libata regression. There shouldn't be any problems with it as corresponding IDE's host driver (pdc202xx_new) has been supporting PCI Power Management since Oct 10 2008 (commit feb22b7f "ide: add proper PCI PM support (v2)") and IDE PM since Jun 14 2003 (patch v2.5.73 "ide: Power Management"). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-10-14pata_legacy: use PIO mask definesBartlomiej Zolnierkiewicz
Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-10-14pata_legacy: unify QDI ->set_piomode methodsBartlomiej Zolnierkiewicz
Add controller type field to struct legacy_data and then use it to merge together all ->set_piomode methods for QDI controllers. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2011-10-14libata: remove no longer needed pata_qdi driverBartlomiej Zolnierkiewicz
QDI65x0 controllers are fully supported by pata_legacy driver so remove no longer needed pata_qdi driver. Leave PATA_QDI config option for compatibility reasons and teach pata_legacy to preserve the old behavior of pata_qdi driver. Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
generated by cgit (git 2.34.1) at 2025-09-30 19:18:34 +0000