| Age | Commit message (Collapse) | Author |
|---|
|
Reset the transmit and receive FIFOs before enabling the UARTs as part
of open() in order to flush any stale data.
Note that the XR21V141X needs a type-specific implementation due to its
UART Manager registers.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The XR22801, XR22802 and XR22804 are compound devices with an embedded
hub and up to seven downstream USB devices including one, two or four
UARTs respectively.
The UART function is similar to XR21B142X but most registers are offset
by 0x40, the register requests are different and are directed at the
device rather than interface, and 5 and 6-bit words are not supported.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The single-port XR21B1411 is similar to the XR21B142X type but uses
12-bit registers and 16-bit register addresses, the register requests
are different and are directed at the device rather than interface, and
5 and 6-bit words are not supported.
The register layout is very similar to XR21B142X except that most
registers are offset by 0xc00 (corresponding to a channel index of 12 in
the MSB of wIndex). As the device is single-port so that the derived
channel index is 0, the current register accessors can be reused after
simply changing the address width.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The XR21B1421, XR21B1422 and XR21B1424 are the one-, two- and four-port
models of a second XR21B142X type of the Maxlinear/Exar USB UARTs.
The XR21B142X type differs from XR21V141X in several ways, including:
- register layout
- register width (16-bit instead of 8-bit)
- vendor register requests
- UART enable/disable sequence
- custom-driver mode flag
- three additional GPIOs (9 instead of 6)
As for XR21V141X, the XR21B142X vendor requests encode the channel index
in the MSB of wIndex, but it lacks the UART Manager registers which
have been replaced by regular UART registers. The new type also uses the
interface number of the control interface (0, 2, 4, 6) as channel index
instead of the channel number (0, 1, 2, 3).
The XR21B142X lacks the divisor and format registers used by XR21V141X
and instead uses the CDC SET_LINE_CONTROL request to configure the line
settings.
Note that the currently supported XR21V141X type lacks the custom-driver
mode flag that prevents the device from entering CDC-ACM mode when a CDC
requests is received. This specifically means that the SET_LINE_CONTROL
request cannot be used with XR21V141X even though it is otherwise
supported.
The UART enable sequence for XR21B142X does not involve explicitly
enabling the FIFOs, but according to datasheet the UART must be disabled
when writing any register but GPIO_SET, GPIO_CLEAR, TX_BREAK and
ERROR_STATUS.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
There are at least four types of Maxlinear/Exar USB UARTs which differ
in various ways such as in their register layouts:
XR21V141X
XR21B142X
XR21B1411
XR22804
It is not clear whether the device type can be inferred from the
descriptors so encode it in the device-id table for now.
Add a type structure that can be used to abstract the register layout
and other features, and use it when accessing the XR21V141X UART
registers that are shared by all types.
Note that the currently supported XR21V141X type is the only type that
has a set of UART Manager registers and that these will need to be
handled specifically.
Similarly, XR21V141X is the only type which has the divisor registers
and that needs to use the format register when configuring the line
settings.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
In preparation for adding support for further types, drop the type
prefix from defines that are not specific to XR21V141X.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
There's no need to configure the pins on every open and judging from the
vendor driver and datasheet it can be done before enabling the UART.
Move pin configuration from open() to port probe and make sure to
deassert DTR and RTS after configuring all pins as GPIO.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Rename the GPIO-pin defines so that they reflect how they are used.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Rename the GPIO mode defines so that they reflect the datasheet and how
they are used.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add support for the two- and four-port variants of XR21V1410.
Use the interface number of each control interface (e.g. 0, 2, 4, 6) to
derive the zero-based channel index:
XR21V1410 0
XR21V1412 0, 1
XR21V1414 0, 1, 2, 3
Note that the UART registers reside in separate blocks per channel,
while the UART Manager functionality is implemented using per-channel
registers.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The kernel does not use any keys besides IA so we don't need to
install IB/DA/DB/GA on kernel exit if we arrange to install them
on task switch instead, which we can expect to happen an order of
magnitude less often.
Furthermore we can avoid installing the user IA in the case where the
user task has IA disabled and just leave the kernel IA installed. This
also lets us avoid needing to install IA on kernel entry.
On an Apple M1 under a hypervisor, the overhead of kernel entry/exit
has been measured to be reduced by 15.6ns in the case where IA is
enabled, and 31.9ns in the case where IA is disabled.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Link: https://linux-review.googlesource.com/id/Ieddf6b580d23c9e0bed45a822dabe72d2ffc9a8e
Link: https://lore.kernel.org/r/2d653d055f38f779937f2b92f8ddd5cf9e4af4f4.1616123271.git.pcc@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This change introduces a prctl that allows the user program to control
which PAC keys are enabled in a particular task. The main reason
why this is useful is to enable a userspace ABI that uses PAC to
sign and authenticate function pointers and other pointers exposed
outside of the function, while still allowing binaries conforming
to the ABI to interoperate with legacy binaries that do not sign or
authenticate pointers.
The idea is that a dynamic loader or early startup code would issue
this prctl very early after establishing that a process may load legacy
binaries, but before executing any PAC instructions.
This change adds a small amount of overhead to kernel entry and exit
due to additional required instruction sequences.
On a DragonBoard 845c (Cortex-A75) with the powersave governor, the
overhead of similar instruction sequences was measured as 4.9ns when
simulating the common case where IA is left enabled, or 43.7ns when
simulating the uncommon case where IA is disabled. These numbers can
be seen as the worst case scenario, since in more realistic scenarios
a better performing governor would be used and a newer chip would be
used that would support PAC unlike Cortex-A75 and would be expected
to be faster than Cortex-A75.
On an Apple M1 under a hypervisor, the overhead of the entry/exit
instruction sequences introduced by this patch was measured as 0.3ns
in the case where IA is left enabled, and 33.0ns in the case where
IA is disabled.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Link: https://linux-review.googlesource.com/id/Ibc41a5e6a76b275efbaa126b31119dc197b927a5
Link: https://lore.kernel.org/r/d6609065f8f40397a4124654eb68c9f490b4d477.1616123271.git.pcc@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
In an upcoming change we are going to introduce per-task SCTLR_EL1
bits for PAC. Move the existing per-task SCTLR_EL1 field out of the
MTE-specific code so that we will be able to use it from both the
PAC and MTE code paths and make the task switching code more efficient.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Link: https://linux-review.googlesource.com/id/Ic65fac78a7926168fa68f9e8da591c9e04ff7278
Link: https://lore.kernel.org/r/13d725cb8e741950fb9d6e64b2cd9bd54ff7c3f9.1616123271.git.pcc@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
We must free 'argv' before returning, as already done in all the other
paths of this function.
Link: https://lkml.kernel.org/r/21e3594ccd7fc88c5c162c98450409190f304327.1618136448.git.christophe.jaillet@wanadoo.fr
Fixes: d262271d0483 ("tracing/dynevent: Delegate parsing to create function")
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
Remove the random white space from the CSIZE switch.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Replace the remaining uses of user-space __XX types.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add two port-command helpers to handle the UART module-id parameter
instead of open coding.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Make the vendor-request helpers data parameters be void pointers and
drop the caller casts.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Drop unnecessary packed attributes from structures that don't need it.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Drop unnecessary packed attributes from structures that don't need it
and use the __packed macro consistently.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Use kernel types consistently by replacing the remaining __uXX types.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add a read-port-command helper analogous to the send-port-command
helper to take care of the UART module id instead of open coding.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add a send-port-command helper which takes care of determining the UART
module id when sending commands instead of doing so at every call site.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Clean up the vendor-request helpers by using kernel-types consistently
and using void pointers for the data arguments, which allows removing
a cast from one caller.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Unlike the TUSB5052, the TUSB3410 has an LSR TEMT bit to tell if both
the transmitter data and shift registers are empty.
Make sure to check also the shift register on TUSB3410 when waiting for
the transmit buffer to drain during close and drop the time-based
one-char delay which is otherwise needed (e.g. 90 ms at 110 bps).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The three-character drain delay was added by commit f1175daa5312 ("USB:
ti_usb_3410_5052: kill custom closing_wait") when removing the custom
closing-wait implementation, which used a fixed 20 ms poll period and
drain delay.
This was likely a bit too conservative as a one-character timeout (e.g.
33 ms at 300 bps) should be enough to compensate for the lack of a
transmitter empty bit in the TUSB5052 line-status register.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Document that the device line-status register doesn't tell when the
transmitter shift register has emptied and that this is why the
one-character drain delay is needed.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The f81232 driver now waits for the transmit FIFO to drain during close
so there is no need to keep the time-based drain delay, which would add
up to two seconds on every close for low line speeds.
Fixes: 98405f81036d ("USB: serial: f81232: add tx_empty function")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Normally, If the smi-larb HW need work, we should enable the smi-common
HW power and clock firstly.
This patch adds device-link between the smi-larb dev and the smi-common
dev. then If pm_runtime_get_sync(smi-larb-dev), the pm_runtime_get_sync
(smi-common-dev) will be called automatically.
Also, Add DL_FLAG_STATELESS to avoid the smi-common clocks be gated when
probe.
CC: Matthias Brugger <matthias.bgg@gmail.com>
Suggested-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210410091128.31823-5-yong.wu@mediatek.com
|
|
clk_set_parent() can fail and ignoring such case could lead to invalid
clock setup for given frequency.
Addresses-Coverity: Unchecked return value
Fixes: 6e7674c3c6df ("memory: Add DMC driver for Exynos5422")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20210407154535.70756-1-krzysztof.kozlowski@canonical.com
|
|
The platform_get_resource_byname() can return NULL which would be
immediately dereferenced by resource_size(). Instead dereference it
after validating the resource.
Addresses-Coverity: Dereference null return value
Fixes: ca7d8b980b67 ("memory: add Renesas RPC-IF driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210407154357.70200-1-krzysztof.kozlowski@canonical.com
|
|
When mmaping an extra device region verify that the region index
derived from the mmap offset is valid.
Fixes: a15b1883fee1 ("vfio_pci: Allow mapping extra regions")
Cc: stable@vger.kernel.org
Signed-off-by: Christian A. Ehrhardt <lk@c--e.de>
Message-Id: <20210412214124.GA241759@lisa.in-ulm.de>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Commit 1a1c130ab757 ("ACPI: tables: x86: Reserve memory occupied by
ACPI tables") attempted to address an issue with reserving the memory
occupied by ACPI tables, but it broke the initrd-based table override
mechanism relied on by multiple users.
To restore the initrd-based ACPI table override functionality, move
the acpi_boot_table_init() invocation in setup_arch() on x86 after
the acpi_table_upgrade() one.
Fixes: 1a1c130ab757 ("ACPI: tables: x86: Reserve memory occupied by ACPI tables")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The DSDT and ACPI should be capitalized.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The macro requires to call acpi_dev_put() on each iteration.
Due to this it doesn't tolerate sudden disappearence of the devices.
Document all these nuances to prevent users blindly call it without
understanding the possible issues.
While at it, add the note to the acpi_dev_get_next_match_dev() and
advertise acpi_dev_put() instead of put_device() in the whole family
of the helper functions.
Fixes: bf263f64e804 ("media: ACPI / bus: Add acpi_dev_get_next_match_dev() and helper macro")
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Introduce acpi_dev_get() to have a symmetrical API with acpi_dev_put()
and reuse both in ACPI code in drivers/acpi/.
While at it, use acpi_bus_put_acpi_device() in one place instead of
the above.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently there are a number of places in the SVE code where we check both
system_supports_sve() and TIF_SVE. This is a bit redundant given that we
should never get into a situation where we have set TIF_SVE without having
SVE support and it is not clear that silently ignoring a mistakenly set
TIF_SVE flag is the most sensible error handling approach. For now let's
just drop the system_supports_sve() checks since this will at least reduce
overhead a little.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210412172320.3315-1-broonie@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Function parameter 'cmd' is rewritten with unused value at locks.c
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
|
|
When updating pin names for Intel Lewisburg, the numbers of pins were
left behind. Update them accordingly.
Fixes: e66ff71fd0db ("pinctrl: lewisburg: Update pin list according to v1.1v6")
Signed-off-by: Yuanyuan Zhong <yzhong@purestorage.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
When dwc2 core is in clock gating mode loading driver
again causes driver fail. Because in that mode
registers are not accessible.
Added a flow of exiting clock gating mode
to avoid the driver reload failure.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073731.3C81BA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If not hibernation nor partial power down are supported,
port resume is done using the clock gating programming flow.
Adds a new flow of exiting clock gating when PC is
resumed.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073723.BA0FEA022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If not hibernation nor partial power down are supported,
clock gating is used to save power.
Adds a new flow of entering clock gating when PC is
suspended.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073716.30C13A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When core is in clock gating state and an external
hub is connected, upper layer sends URB enqueue request,
which results in port reset issue.
Added exit from clock gating state to avoid port
reset issue and process upper layer request properly.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073708.ADFC6A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Updates the implementation of exiting clock gating mode
when core receives port resume.
Instead of setting the required bit fields of the registers
inline, called the "dwc2_host_exit_clock_gating()" function.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073701.367E0A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Updates the implementation of entering clock gating mode
when core receives port suspend.
Instead of setting the required bit fields of the registers
inline, called the "dwc2_host_enter_clock_gating()" function.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073653.9F493A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adds clock gating exit flow when set port feature
reset is received in suspended state.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073646.27217A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Added clock gating exit flow from session
request interrupt handler according programming guide.
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073638.921E8A0099@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Added exit from clock gating mode when wakeup interrupt
is detected. To exit from the clock gating
in device mode "dwc2_gadget_exit_clock_gating()"
function is used with rem_wakeup parameter 0. To exit
clock gating in host mode "dwc2_host_exit_clock_gating()"
with rem_wakeup parameter 1.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073630.EF2CEA0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If core doesn't support hibernation or partial power
down power saving options, power can still be saved
using clock gating on all the clocks.
- Added entering clock gating state from USB_SUSPEND
interrupt.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073623.65355A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Added host clock gating support functions according
programming guide.
Added function names:
dwc2_host_enter_clock_gating()
dwc2_host_exit_clock_gating()
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210413073615.B3E84A022E@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
