| Age | Commit message (Collapse) | Author |
|---|
|
A recent bug report outlined that the way GICv4.1 is handled across
kexec is pretty bad. We can end-up in a situation where ITSs share
memory (this is the case when SVPET==1) and reprogram the base
registers, creating a situation where ITSs that are part of a given
affinity group see different pointers. Which is illegal. Boo.
In order to restore some sanity, reset the BASERn registers to 0
*before* probing any ITS. Although this isn't optimised at all,
this is only a once-per-boot cost, which shouldn't show up on
anyone's radar.
Cc: Jay Chen <jkchen@linux.alibaba.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20211216190315.GA14220@lpieralisi
Link: https://lore.kernel.org/r/20220124133809.1291195-1-maz@kernel.org
|
|
Lift the dsc/joiner enable up from the wonky places where it
currently sits (ddi .pre_enable() or icl_ddi_bigjoiner_pre_enable())
into hsw_crtc_enable() where we write the other per-pipe stuff
as well. Makes the transcoder vs. pipe split less confusing.
For DSI this results in slight reordering between the dsc/joiner
enable vs. transcoder timings setup, but I can't really think
why that should cause any issues since the transcoder isn't yet
enabled at that point.
v2: Take care of dsi (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220125063937.7003-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Pull the transcoder specific modeset steps into a single place.
With bigoiner we need to keep in mind wheher we're dealing with
the transcoder or the pipe, and a slightly higher level split makes
that easier.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124192638.26262-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Specify which device we're talking about when spewing
bigjoiner debugs.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124192638.26262-3-ville.syrjala@linux.intel.com
|
|
We can simplify the icl check in intel_dsc_source_support()
by noting that the only case when DSC is not supported is when
using transcoder A.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124192638.26262-2-ville.syrjala@linux.intel.com
|
|
Trying to do readout when we don't even have a cpu transcoder
is not a great idea. Don't do it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124192638.26262-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
This reverts commit 9bb7b689274b67ecb3641e399e76f84adc627df1.
This caused a regression reported to Red Hat.
Fixes: 9bb7b689274b ("drm/ast: Support 1600x900 with 108MHz PCLK")
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120040527.552068-1-airlied@gmail.com
|
|
Backmerging drm/drm-fixes into drm-misc-fixes for v5.17-rc1.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
In terms of async flip optimization we don't to allocate
extra ddb space, so lets skip it.
v2: - Extracted min ddb async flip check to separate function
(Ville Syrjälä)
- Used this function to prevent false positive WARN
to be triggered(Ville Syrjälä)
v3: - Renamed dg2_need_min_ddb to need_min_ddb thus making
it more universal.
- Also used DISPLAY_VER instead of IS_DG2(Ville Syrjälä)
- Use rate = 0 instead of just setting extra = 0, thus
letting other planes to use extra ddb and avoiding WARN
(Ville Syrjälä)
v4: - Renamed needs_min_ddb as s/needs/use/ to match
the wm0 counterpart(Ville Syrjälä)
- Added plane->async_flip check to use_min_ddb(now
passing plane as a parameter to do that)(Ville Syrjälä)
- Account for use_min_ddb also when calculating total data rate
(Ville Syrjälä)
v5:
- Use for_each_intel_plane_on_crtc instead of for_each_intel_plane_id
to get plane->async_flip check and account for all planes(Ville Syrjälä)
- Fix line wrapping(Ville Syrjälä)
- Set plane data rate conditionally, avoiding on redundant assignment
(Ville Syrjälä)
- Removed redundant whitespace(Ville Syrjälä)
- Handle use_min_ddb case in skl_plane_relative_data_rate instead of
icl_get_total_relative_data_rate(Ville Syrjälä)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124090653.14547-2-stanislav.lisovskiy@intel.com
|
|
This optimization allows to achieve higher perfomance
during async flips.
For the first async flip we have to still temporarily
switch to sync flip, in order to reprogram plane
watermarks, so this requires taking into account
old plane state's do_async_flip flag.
v2: - Removed redundant new_plane_state->do_async_flip
check from needs_async_flip_wm_override condition
(Ville Syrjälä)
- Extract dg2_async_flip_optimization to separate
function(Ville Syrjälä)
- Check for plane->async_flip instead of plane_id
(Ville Syrjälä)
v3: - Rename "needs_async_flip_wm_override" to
"intel_plane_do_async_flip" and move all the required
checks there (Ville Syrjälä)
- Rename "dg2_async_flip_optimization" to
"use_minimal_wm0_only" (Ville Syrjälä)
v4: - Swap new/old_crtc_state in intel_plane_do_async_flip
argument list(Ville Syrjälä)
- Use plane->base.dev to grab i915 pointer in
intel_plane_do_async_flip(Ville Syrjälä)
- Remove const modifier from plane parameter in
use_minimal_wm0_only(Ville Syrjälä)
- Swap also new/old_crtc_state at intel_plane_do_async_flip
call site(Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124094929.31722-1-stanislav.lisovskiy@intel.com
|
|
There might be various logical contructs when we might want
to enable async flip, so lets calculate those and set this
flag, so that there is no need in long conditions in other
places.
v2: - Set do_async_flip flag to False, if no async flip needed.
Lets not rely that it will be 0-initialized, but set
explicitly, so that the logic is clear as well.
v3: - Clear do_async_flip in intel_plane_duplicate_state(Ville Syrjälä)
- Check with do_async_flip also when calling
intel_crtc_{enable,disable}_flip_done(Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124090653.14547-3-stanislav.lisovskiy@intel.com
|
|
Sometimes we might need to change the way we calculate
watermarks, based on which particular plane it is calculated
for. Thus it would be convenient to pass plane struct to those
functions.
v2: Pass plane instead of plane_id
v3: Do not pass plane to skl_cursor_allocation(Ville Syrjälä)
v4: - Make intel_crtc_get_plane static again(Ville Syrjälä)
- s/cursor_plane/plane(Ville Syrjälä)
- Pass plane to skl_compute_wm_* instead of plane_id(Ville Syrjälä)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124090653.14547-2-stanislav.lisovskiy@intel.com
|
|
Complete the ilk pch modeset abstraction by adding ilk_pch_pre_enable().
I did the disable vs. post_disable split already for the disable
sequence, but the enable sequence was still left with the naked
ilk_fdi_pll_enable() call for some reason.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124193136.2397-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
The current implementation of HTB offload doesn't support some
parameters. Instead of ignoring them, actively return the EINVAL error
when they are set to non-defaults.
As this patch goes to stable, the driver API is not changed here. If
future drivers support more offload parameters, the checks can be moved
to the driver side.
Note that the buffer and cbuffer parameters are also not supported, but
the tc userspace tool assigns some default values derived from rate and
ceil, and identifying these defaults in sch_htb would be unreliable, so
they are still ignored.
Fixes: d03b195b5aa0 ("sch_htb: Hierarchical QoS hardware offload")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220125100654.424570-1-maximmi@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Function pcie_rmw() is not being used at all and can be deleted. Hence get
rid of it, which fixes this warning:
drivers/pci/controller/pcie-mt7621.c:112:20: warning: unused function 'pcie_rmw' [-Wunused-function]
Fixes: 2bdd5238e756 ("PCI: mt7621: Add MediaTek MT7621 PCIe host controller driver")
Link: https://lore.kernel.org/r/20220124113003.406224-3-sergio.paracuellos@gmail.com
Link: https://lore.kernel.org/all/202201241754.igtHzgHv-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
We have stubs for most OF interfaces even when CONFIG_OF is not set, so we
allow building of pcie-mt7621.c in that case for compile testing.
When CONFIG_OF is not set, "of_match_ptr(mt7621_pcie_ids)" compiles to
NULL, which leaves mt7621_pcie_ids unused:
$ make W=1
drivers/pci/controller/pcie-mt7621.c:549:34: warning: unused variable 'mt7621_pcie_ids' [-Wunused-const-variable]
Drop of_match_ptr() to avoid the unused variable warning.
[bhelgaas: commit log]
Fixes: 2bdd5238e756 ("PCI: mt7621: Add MediaTek MT7621 PCIe host controller driver")
Link: https://lore.kernel.org/r/20220124113003.406224-2-sergio.paracuellos@gmail.com
Link: https://lore.kernel.org/r/202201241754.igtHzgHv-lkp@intel.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Unused. Convert the divisions into asserts on the divisor, to
debug why it is zero. The divide by zero is suspected of causing
kernel panics.
While I have no idea where the zero is coming from I think this
patch is a positive either way.
Cc: stable@vger.kernel.org
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Mirrors the logic for dcn30. Cue lots of WARNs and some
kernel panics without this fix.
Cc: stable@vger.kernel.org
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It calls populate_dml_pipes which uses doubles to initialize the
scale_ratio_depth params. Mirrors the dcn20 logic.
Cc: stable@vger.kernel.org
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
In calculate_bandwidth(), the tag free_sclk and free_yclk are reversed,
which could lead to a memory leak of yclk.
Fix this bug by changing the location of free_sclk and free_yclk.
This bug was found by a static analyzer.
Builds with 'make allyesconfig' show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 2be8989d0fc2 ("drm/amd/display/dc/calcs/dce_calcs: Move some large variables from the stack to the heap")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Some architectures (e.g., ARM) throw an compilation error if the
udelay is too long. In general udelays of longer than 2000us are
not recommended on any architecture. Switch to msleep in these
cases.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Some architectures (e.g., ARM) have relatively low udelay limits.
On most architectures, anything longer than 2000us is not recommended.
Change the check to align with other similar checks in DC.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Older radeon boards (r2xx-r5xx) had secondary PCI functions
which we solely there for supporting multi-head on OSs with
special requirements. Add them to the unsupported list
as well so we don't attempt to bind to them. The driver
would fail to bind to them anyway, but this does so
in a cleaner way that should not confuse the user.
Cc: stable@vger.kernel.org
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
FIFO reset is only necessary for fast boot sequence, where otg is disabled
and dig fe is enabled when changing dispclk. Fast boot is only enabled
on embedded displays.
[How]
Change FIFO reset condition to "embedded display only".
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
DCN301 has seamless boot enabled. With MPC split enabled
at the same time, system will hang.
[How]
Revert MPC split policy back to "MPC_SPLIT_AVOID". Since we have
ODM combine enabled on DCN301, pipe split is not necessary here.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
During otg sync trigger, plane states are used to decide whether the otg
is already synchronized or not. There are scenarions when otgs are
disabled without plane state getting disabled and in such case the otg is
excluded from synchronization.
[How]
Introduced pipe_idx_syncd in pipe_ctx that tracks each otgs master pipe.
When a otg is disabled/enabled, pipe_idx_syncd is reset to itself.
On sync trigger, pipe_idx_syncd is checked to decide whether a otg is
already synchronized and the otg is further included or excluded from
synchronization.
v2:
Don't drop is_blanked logic
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Mustapha Ghaddar <mustapha.ghaddar@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: meenakshikumar somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Cc: torvalds@linux-foundation.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The membarrier command MEMBARRIER_CMD_QUERY allows querying the
available membarrier commands. When the membarrier-rseq fence commands
were added, a new MEMBARRIER_CMD_PRIVATE_EXPEDITED_RSEQ_BITMASK was
introduced with the intent to expose them with the MEMBARRIER_CMD_QUERY
command, the but it was never added to MEMBARRIER_CMD_BITMASK.
The membarrier-rseq fence commands are therefore not wired up with the
query command.
Rename MEMBARRIER_CMD_PRIVATE_EXPEDITED_RSEQ_BITMASK to
MEMBARRIER_PRIVATE_EXPEDITED_RSEQ_BITMASK (the bitmask is not a command
per-se), and change the erroneous
MEMBARRIER_CMD_REGISTER_PRIVATE_EXPEDITED_RSEQ_BITMASK (which does not
actually exist) to MEMBARRIER_CMD_REGISTER_PRIVATE_EXPEDITED_RSEQ.
Wire up MEMBARRIER_PRIVATE_EXPEDITED_RSEQ_BITMASK in
MEMBARRIER_CMD_BITMASK. Fixing this allows discovering availability of
the membarrier-rseq fence feature.
Fixes: 2a36ab717e8f ("rseq/membarrier: Add MEMBARRIER_CMD_PRIVATE_EXPEDITED_RSEQ")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org> # 5.10+
Link: https://lkml.kernel.org/r/20220117203010.30129-1-mathieu.desnoyers@efficios.com
|
|
Pull NFS client updates from Anna Schumaker:
"New Features:
- Basic handling for case insensitive filesystems
- Initial support for fs_locations and server trunking
Bugfixes and Cleanups:
- Cleanups to how the "struct cred *" is handled for the
nfs_access_entry
- Ensure the server has an up to date ctimes before hardlinking or
renaming
- Update 'blocks used' after writeback, fallocate, and clone
- nfs_atomic_open() fixes
- Improvements to sunrpc tracing
- Various null check & indenting related cleanups
- Some improvements to the sunrpc sysfs code:
- Use default_groups in kobj_type
- Fix some potential races and reference leaks
- A few tracepoint cleanups in xprtrdma"
[ This should have gone in during the merge window, but didn't. The
original pull request - sent during the merge window - had gotten
marked as spam and discarded due missing DKIM headers in the email
from Anna. - Linus ]
* tag 'nfs-for-5.17-1' of git://git.linux-nfs.org/projects/anna/linux-nfs: (35 commits)
SUNRPC: Don't dereference xprt->snd_task if it's a cookie
xprtrdma: Remove definitions of RPCDBG_FACILITY
xprtrdma: Remove final dprintk call sites from xprtrdma
sunrpc: Fix potential race conditions in rpc_sysfs_xprt_state_change()
net/sunrpc: fix reference count leaks in rpc_sysfs_xprt_state_change
NFSv4.1 test and add 4.1 trunking transport
SUNRPC allow for unspecified transport time in rpc_clnt_add_xprt
NFSv4 handle port presence in fs_location server string
NFSv4 expose nfs_parse_server_name function
NFSv4.1 query for fs_location attr on a new file system
NFSv4 store server support for fs_location attribute
NFSv4 remove zero number of fs_locations entries error check
NFSv4: nfs_atomic_open() can race when looking up a non-regular file
NFSv4: Handle case where the lookup of a directory fails
NFSv42: Fallocate and clone should also request 'blocks used'
NFSv4: Allow writebacks to request 'blocks used'
SUNRPC: use default_groups in kobj_type
NFS: use default_groups in kobj_type
NFS: Fix the verifier for case sensitive filesystem in nfs_atomic_open()
NFS: Add a helper to remove case-insensitive aliases
...
|
|
We need to flush TLBs before releasing backing store otherwise userspace
is able to encounter stale entries if a) it is not declaring access to
certain buffers and b) it races with the backing store release from a
such undeclared execution already executing on the GPU in parallel.
The approach taken is to mark any buffer objects which were ever bound
to the GPU and to trigger a serialized TLB flush when their backing
store is released.
Alternatively the flushing could be done on VMA unbind, at which point
we would be able to ascertain whether there is potential a parallel GPU
execution (which could race), but essentially it boils down to paying
the cost of TLB flushes potentially needlessly at VMA unbind time (when
the backing store is not known to be going away so not needed for
safety), versus potentially needlessly at backing store relase time
(since we at that point cannot tell whether there is anything executing
on the GPU which uses that object).
Thereforce simplicity of implementation has been chosen for now with
scope to benchmark and refine later as required.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reported-by: Sushma Venkatesh Reddy <sushma.venkatesh.reddy@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While all userspace tried to limit commandstreams to 64K in size,
a bug in the Mesa driver lead to command streams of up to 128K
being submitted. Allow those to avoid breaking existing userspace.
Fixes: 6dfa2fab8ddd ("drm/etnaviv: limit submit sizes")
Cc: stable@vger.kernel.org
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
|
|
The syzbot fuzzer has identified a bug in which processes hang waiting
for usb_kill_urb() to return. It turns out the issue is not unlinking
the URB; that works just fine. Rather, the problem arises when the
wakeup notification that the URB has completed is not received.
The reason is memory-access ordering on SMP systems. In outline form,
usb_kill_urb() and __usb_hcd_giveback_urb() operating concurrently on
different CPUs perform the following actions:
CPU 0 CPU 1
---------------------------- ---------------------------------
usb_kill_urb(): __usb_hcd_giveback_urb():
... ...
atomic_inc(&urb->reject); atomic_dec(&urb->use_count);
... ...
wait_event(usb_kill_urb_queue,
atomic_read(&urb->use_count) == 0);
if (atomic_read(&urb->reject))
wake_up(&usb_kill_urb_queue);
Confining your attention to urb->reject and urb->use_count, you can
see that the overall pattern of accesses on CPU 0 is:
write urb->reject, then read urb->use_count;
whereas the overall pattern of accesses on CPU 1 is:
write urb->use_count, then read urb->reject.
This pattern is referred to in memory-model circles as SB (for "Store
Buffering"), and it is well known that without suitable enforcement of
the desired order of accesses -- in the form of memory barriers -- it
is entirely possible for one or both CPUs to execute their reads ahead
of their writes. The end result will be that sometimes CPU 0 sees the
old un-decremented value of urb->use_count while CPU 1 sees the old
un-incremented value of urb->reject. Consequently CPU 0 ends up on
the wait queue and never gets woken up, leading to the observed hang
in usb_kill_urb().
The same pattern of accesses occurs in usb_poison_urb() and the
failure pathway of usb_hcd_submit_urb().
The problem is fixed by adding suitable memory barriers. To provide
proper memory-access ordering in the SB pattern, a full barrier is
required on both CPUs. The atomic_inc() and atomic_dec() accesses
themselves don't provide any memory ordering, but since they are
present, we can use the optimized smp_mb__after_atomic() memory
barrier in the various routines to obtain the desired effect.
This patch adds the necessary memory barriers.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+76629376e06e2c2ad626@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8K0QYee0Q0Nna2@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Two people have reported (and mentioned numerous other reports on the
web) that VIA's VL817 USB-SATA bridge does not work with the uas
driver. Typical log messages are:
[ 3606.232149] sd 14:0:0:0: [sdg] tag#2 uas_zap_pending 0 uas-tag 1 inflight: CMD
[ 3606.232154] sd 14:0:0:0: [sdg] tag#2 CDB: Write(16) 8a 00 00 00 00 00 18 0c c9 80 00 00 00 80 00 00
[ 3606.306257] usb 4-4.4: reset SuperSpeed Plus Gen 2x1 USB device number 11 using xhci_hcd
[ 3606.328584] scsi host14: uas_eh_device_reset_handler success
Surprisingly, the devices do seem to work okay for some other people.
The cause of the differing behaviors is not known.
In the hope of getting the devices to work for the most users, even at
the possible cost of degraded performance for some, this patch adds an
unusual_devs entry for the VL817 to block it from binding to the uas
driver by default. Users will be able to override this entry by means
of a module parameter, if they want.
CC: <stable@vger.kernel.org>
Reported-by: DocMAX <mail@vacharakis.de>
Reported-and-tested-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8IsK2sjlEv1rqU@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With some chargers, vbus might momentarily raise above VSAFE5V and fall
back to 0V causing VSAFE0V to be triggered. This will
will report a VBUS off event causing TCPM to transition to
SNK_UNATTACHED state where it should be waiting in either SNK_ATTACH_WAIT
or SNK_DEBOUNCED state. This patch makes TCPM avoid VSAFE0V events
while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state.
Stub from the spec:
"4.5.2.2.4.2 Exiting from AttachWait.SNK State
A Sink shall transition to Unattached.SNK when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
A DRP shall transition to Unattached.SRC when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."
[23.194131] CC1: 0 -> 0, CC2: 0 -> 5 [state SNK_UNATTACHED, polarity 0, connected]
[23.201777] state change SNK_UNATTACHED -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[23.209949] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[23.300579] VBUS off
[23.300668] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [rev3 NONE_AMS]
[23.301014] VBUS VSAFE0V
[23.301111] Start toggling
Fixes: 28b43d3d746b8 ("usb: typec: tcpm: Introduce vsafe0v for vbus")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220122015520.332507-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With some chargers, vbus might momentarily raise above VSAFE5V and fall
back to 0V before tcpm gets to read port->tcpc->get_vbus. This will
will report a VBUS off event causing TCPM to transition to
SNK_UNATTACHED where it should be waiting in either SNK_ATTACH_WAIT
or SNK_DEBOUNCED state. This patch makes TCPM avoid vbus off events
while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state.
Stub from the spec:
"4.5.2.2.4.2 Exiting from AttachWait.SNK State
A Sink shall transition to Unattached.SNK when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
A DRP shall transition to Unattached.SRC when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."
[23.194131] CC1: 0 -> 0, CC2: 0 -> 5 [state SNK_UNATTACHED, polarity 0, connected]
[23.201777] state change SNK_UNATTACHED -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[23.209949] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[23.300579] VBUS off
[23.300668] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [rev3 NONE_AMS]
[23.301014] VBUS VSAFE0V
[23.301111] Start toggling
Fixes: f0690a25a140b8 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220122015520.332507-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Missed adding the Icelake-D CPU to the list. It uses the same MSRs
to control and read the inventory number as all the other models.
Fixes: dc6b025de95b ("x86/mce: Add Xeon Icelake to list of CPUs that support PPIN")
Reported-by: Ailin Xu <ailin.xu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220121174743.1875294-2-tony.luck@intel.com
|
|
This fixes NULL pointer dereference that happens if
component master is registered with empty component match
list.
Fixes: 730b49aac426 ("usb: typec: port-mapper: Convert to the component framework")
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220124090228.41396-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The code that creates the links to the USB ports attached to
a connector inside the system assumed that the ACPI nodes
(fwnodes) always exist for the connectors, but it can not do
that.
There is no guarantee that every USB Type-C connector has
ACPI device node representing it in the ACPI tables, and
even if there are the nodes in the ACPI tables, the _STA
method in those nodes may still return 0 (which means the
device does not exist from ACPI PoW).
This fixes NULL pointer dereference that happens if the
nodes are missing.
Fixes: 730b49aac426 ("usb: typec: port-mapper: Convert to the component framework")
Reported-and-tested-by: Robert Święcki <robert@swiecki.net>
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220124090228.41396-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With the AMS and Collision Avoidance, tcpm often needs to change the CC's
termination. When one CC line is sourcing Vconn, if we still change its
termination, the voltage of the another CC line is likely to be fluctuant
and unstable.
Therefore, we should verify whether a CC line is sourcing Vconn before
changing its termination and only change the termination that is not
a Vconn line. This can be done by reading the Vconn Present bit of
POWER_ STATUS register. To determine the polarity, we can read the
Plug Orientation bit of TCPC_CONTROL register. Since Vconn can only be
sourced if Plug Orientation is set.
Fixes: 0908c5aca31e ("usb: typec: tcpm: AMS and Collision Avoidance")
cc: <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20220113092943.752372-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is an unused wrapper forcing kmalloc allocation for registering
nosave regions. Also, rename __register_nosave_region() to
register_nosave_region() now that there is no need for disambiguation.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
when CONFIG_USB_ROLE_SWITCH is not defined,
add usb_role_switch_find_by_fwnode() definition which return NULL.
Fixes: c6919d5e0cd1 ("usb: roles: Add usb_role_switch_find_by_fwnode()")
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/1641818608-25039-1-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The buffer handling in pm_show_wakelocks() is tricky, and hopefully
correct. Ensure it really is correct by using sysfs_emit_at() which
handles all of the tricky string handling logic in a PAGE_SIZE buffer
for us automatically as this is a sysfs file being read from.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Copy scattered mac address octets into an array then eth_hw_addr_set().
Fixes: adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lore.kernel.org/r/20220125144007.64407-1-tsbogend@alpha.franken.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With system suspend using pm_runtime_force_suspend() we can't rely on
the pm_runtime_get_if_in_use() trick to deal with devfreq callbacks
after (or racing with) suspend. So flush any pending idle or boost
work in the suspend path.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20220108180913.814448-3-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
System suspend uses pm_runtime_force_suspend(), which cheekily bypasses
the runpm reference counts. This doesn't actually work so well when the
GPU is active. So add a reasonable delay waiting for the GPU to become
idle.
Alternatively we could just return -EBUSY in this case, but that has the
disadvantage of causing system suspend to fail.
v2: s/ret/remaining [sboyd], and switch to using active_submits count
to ensure we aren't racing with submit cleanup (and devfreq idle
work getting scheduled, etc)
v3: fix inverted logic
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220108180913.814448-2-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Several fixes for defragmentation that got broken in 5.16 after
refactoring and added subpage support. The observed bugs are excessive
IO or uninterruptible ioctl.
All stable material"
* tag 'for-5.17-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: update writeback index when starting defrag
btrfs: add back missing dirty page rate limiting to defrag
btrfs: fix deadlock when reserving space during defrag
btrfs: defrag: properly update range->start for autodefrag
btrfs: defrag: fix wrong number of defragged sectors
btrfs: allow defrag to be interruptible
btrfs: fix too long loop when defragging a 1 byte file
|
|
Make kvm_vcpu_reload_apic_access_page() static
as it is no longer invoked directly by vmx
and it is also no longer exported.
No functional change intended.
Signed-off-by: Quanfa Fu <quanfafu@gmail.com>
Message-Id: <20211219091446.174584-1-quanfafu@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This selftest was accidentally removed by commit 6a58150859fd
("selftest: KVM: Add intra host migration tests"). Add it back.
Fixes: 6a58150859fd ("selftest: KVM: Add intra host migration tests")
Signed-off-by: David Matlack <dmatlack@google.com>
Message-Id: <20220120003826.2805036-1-dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Set vmcs.GUEST_PENDING_DBG_EXCEPTIONS.BS, a.k.a. the pending single-step
breakpoint flag, when re-injecting a #DB with RFLAGS.TF=1, and STI or
MOVSS blocking is active. Setting the flag is necessary to make VM-Entry
consistency checks happy, as VMX has an invariant that if RFLAGS.TF is
set and STI/MOVSS blocking is true, then the previous instruction must
have been STI or MOV/POP, and therefore a single-step #DB must be pending
since the RFLAGS.TF cannot have been set by the previous instruction,
i.e. the one instruction delay after setting RFLAGS.TF must have already
expired.
Normally, the CPU sets vmcs.GUEST_PENDING_DBG_EXCEPTIONS.BS appropriately
when recording guest state as part of a VM-Exit, but #DB VM-Exits
intentionally do not treat the #DB as "guest state" as interception of
the #DB effectively makes the #DB host-owned, thus KVM needs to manually
set PENDING_DBG.BS when forwarding/re-injecting the #DB to the guest.
Note, although this bug can be triggered by guest userspace, doing so
requires IOPL=3, and guest userspace running with IOPL=3 has full access
to all I/O ports (from the guest's perspective) and can crash/reboot the
guest any number of ways. IOPL=3 is required because STI blocking kicks
in if and only if RFLAGS.IF is toggled 0=>1, and if CPL>IOPL, STI either
takes a #GP or modifies RFLAGS.VIF, not RFLAGS.IF.
MOVSS blocking can be initiated by userspace, but can be coincident with
a #DB if and only if DR7.GD=1 (General Detect enabled) and a MOV DR is
executed in the MOVSS shadow. MOV DR #GPs at CPL>0, thus MOVSS blocking
is problematic only for CPL0 (and only if the guest is crazy enough to
access a DR in a MOVSS shadow). All other sources of #DBs are either
suppressed by MOVSS blocking (single-step, code fetch, data, and I/O),
are mutually exclusive with MOVSS blocking (T-bit task switch), or are
already handled by KVM (ICEBP, a.k.a. INT1).
This bug was originally found by running tests[1] created for XSA-308[2].
Note that Xen's userspace test emits ICEBP in the MOVSS shadow, which is
presumably why the Xen bug was deemed to be an exploitable DOS from guest
userspace. KVM already handles ICEBP by skipping the ICEBP instruction
and thus clears MOVSS blocking as a side effect of its "emulation".
[1] http://xenbits.xenproject.org/docs/xtf/xsa-308_2main_8c_source.html
[2] https://xenbits.xen.org/xsa/advisory-308.html
Reported-by: David Woodhouse <dwmw2@infradead.org>
Reported-by: Alexander Graf <graf@amazon.de>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220120000624.655815-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Full equality check of CPUID data on update (kvm_cpuid_check_equal()) may
fail for SGX enabled CPUs as CPUID.(EAX=0x12,ECX=1) is currently being
mangled in kvm_vcpu_after_set_cpuid(). Move it to
__kvm_update_cpuid_runtime() and split off cpuid_get_supported_xcr0()
helper as 'vcpu->arch.guest_supported_xcr0' update needs (logically)
to stay in kvm_vcpu_after_set_cpuid().
Cc: stable@vger.kernel.org
Fixes: feb627e8d6f6 ("KVM: x86: Forbid KVM_SET_CPUID{,2} after KVM_RUN")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20220124103606.2630588-2-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Since some interrupt states may be cleared by hardware, the driver
may receive an empty interrupt. Currently, the VF driver directly
disables the vector0 interrupt in this case. As a result, the VF
is unavailable. Therefore, the vector0 interrupt should be enabled
in this case.
Fixes: b90fcc5bd904 ("net: hns3: add reset handling for VF when doing Core/Global/IMP reset")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
