| Age | Commit message (Collapse) | Author |
|---|
|
This adds device tree bindings to the power management controller
in the Gemini SoC.
Cc: devicetree@vger.kernel.org
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Make the syscon-poweroff driver accept value and mask instead of
just value.
Prior to this patch, the property name for the value was 'mask'. If
only the mask property is defined on a node, maintain compatibility
by using it as the value.
Signed-off-by: Guy Shapiro <guy.shapiro@mobi-wize.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
We can get quite a few interrupts when the battery is trickle charging.
Let's enable PM runtime autosuspend to avoid constantly toggling device
driver PM runtime state.
Let's use a 600 ms timeout as that's how long the USB chager detection
might take.
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Some SoCs like omap3 can configure GPIO irqs to use Linux generic
dedicated wakeirq support. If the dedicated wakeirq is configured,
the SoC will use a always-on interrupt controller to produce wake-up
events.
If bq24190 is configured for dedicated wakeirq, we need to check the
interrupt status on PM runtime resume. This is because the Linux
generic wakeirq will call pm_runtime_resume() on the device on a
wakeirq. And as the bq24190 interrupt is falling edge sensitive
and only active for 250 us, there will be no device interrupt seen
by the runtime SoC IRQ controller.
Note that this can cause spurious interrupts on omap3 devices with
bq24190 connected to gpio banks 2 - 5 as there's a glitch on those
pins waking from off mode as listed in "Advisory 1.45". Devices
with this issue should not configure the optional wakeirq interrupt
in the dts file.
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
This fixes a math error calculating the extra_vecs. The error assumed
only 1 cpu per vector, but the value needs to account for the actual
number of cpus per vector in order to get the correct remainder for
extra CPU assignment.
Fixes: 7bf8222b9bd0 ("irq/affinity: Fix CPU spread for unbalanced nodes")
Reported-by: Xiaolong Ye <xiaolong.ye@intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Link: http://lkml.kernel.org/r/1492104492-19943-1-git-send-email-keith.busch@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Current codes invoke wrongly nf_ct_netns_get in the destroy routine,
it should use nf_ct_netns_put, not nf_ct_netns_get.
It could cause some modules could not be unloaded.
Fixes: ecb2421b5ddf ("netfilter: add and use nf_ct_netns_get/put")
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This can prevent the nft utility from printing out the auto generated
seed to the user, which is unnecessary and confusing.
Fixes: cb1b69b0b15b ("netfilter: nf_tables: add hash expression")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Telit LE920A4 uses the same pid 0x1201 of LE920, but modem
implementation is different, since it requires DTR to be set for
answering to qmi messages.
This patch replaces QMI_FIXED_INTF with QMI_QUIRK_SET_DTR: tests on
LE920 have been performed in order to verify backward compatibility.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Revert commit 57707a9a7780 (ACPICA: Resources: Not a valid resource if
buffer length too long) as it is reported to prevent the TPM module
from loading on Lenovo X60 with Coreboot.
It also causes new confusing warnings to show up in the kernel log.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195311
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Two pin control fixes arriving late, these are hopefully the last pin
control fixes I send this kernel cycle. A Chromebook and an Exynos SoC
thingie.
The Exynos patch is pretty big, it is fixing unbroken a breakage
caused by yours truly when trying to figure out the merge mess with
the different Samsung platforms for this merge window. Sorry about
that. We have countered this situation by assigning a Samsung pin
control submaintainer to catch stuff earlier.
Summary:
- Make the Acer Chromebook keyboard work again with the Intel
Cherryview driver.
- Fix a merge error in the Exynos 5433 driver"
* tag 'pinctrl-v4.11-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: cherryview: Add a quirk to make Acer Chromebook keyboard work again
pinctrl: samsung: Add missing part for PINCFG_TYPE_DRV of Exynos5433
|
|
I'm hitting the BUG in nfsd4_max_reply() at fs/nfsd/nfs4proc.c:2495 when
client sends an operation the server doesn't support.
in nfsd4_max_reply() it checks for NULL rsize_bop but a non-supported
operation wouldn't have that set.
Cc: Kinglong Mee <kinglongmee@gmail.com>
Fixes: 2282cd2c05e2 "NFSD: Get response size before operation..."
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Commit ef65aaede23f ("smb2: Enforce sec= mount option") changed the
behavior of a mount command to enforce a specified security mechanism
during mounting. On another hand according to the spec if SMB3 server
doesn't respond with a security context it implies that it supports
NTLMSSP. The current code doesn't keep it in mind and fails a mount
for such servers if no security mechanism is specified. Fix this by
indicating that a server supports NTLMSSP if a security context isn't
returned during negotiate phase. This allows the code to use NTLMSSP
by default for SMB3 mounts.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <smfrench@gmail.com>
|
|
In https://lkml.org/lkml/2017/2/2/16 I reported a build error that I
believed was caused by wrong uapi includes. The synthom was fixed by
Arnaldo in:
commit 2f7db5557994 ("perf tools: Fix include of linux/mman.h")
but I was wrong attributing the problem to the uapi include.
The root cause was that I was using ARCH=x86_64, hence using the wrong
uapi include path. This explains why no one else ran into this build
problem.
Signed-off-by: David Carrillo-Cisneros <davidcc@google.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Simon Que <sque@chromium.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/20170412064919.92449-8-davidcc@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Besides memory allocation failure, tips.txt may fail to load because the
file is not found (a more likely cause).
Communicate that to the user in tips failure warning.
Signed-off-by: David Carrillo-Cisneros <davidcc@google.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Simon Que <sque@chromium.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/20170412064919.92449-5-davidcc@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
This change is a follow up of https://lkml.org/lkml/2017/2/2/16
The patch above avoided redefining CC, CXX and PKG_CONFIG in feature
detection. The patch was not merged due to a unsolved concern with the
-MD flag.
Later, commit c8c188679ccf ("tools build: Use the same CC for feature
detection and actual build") did the change for CC and CXX but not
PKG_CONFIG.
This patch makes PKG_CONFIG consistent with CC and CXX and moves the -MD
to CFLAGS, as suggested by Jiri in the thread above.
Signed-off-by: David Carrillo-Cisneros <davidcc@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Simon Que <sque@chromium.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/20170412064919.92449-3-davidcc@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The build of JVMTI depends on LIBELF (-lelf). Make Makefile.conf
check this dependendancy and notify user when not present.
v2: Comma nitpicking.
Signed-off-by: David Carrillo-Cisneros <davidcc@google.com>
Tested-by: Kim Phillips <kim.phillips@arm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Simon Que <sque@chromium.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/20170412170745.26620-1-davidcc@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
perf trace supports --no-syscalls option but it's not listed in the man
page. (Though, I see an example using --no-syscalls in EXAMPLES
section.)
Committer note:
The --no-syscalls option tells 'perf trace' not to automagically ask for
raw_syscalls:sys_{enter,exit} to then format it in a strace like way.
This become more used as 'perf trace' got support for arbitrary events,
such as tracepoints, so more and more we use:
# perf trace --no-syscalls -e nmi:*
0.000 nmi:nmi_handler:perf_event_nmi_handler() delta_ns: 36649 handled: 1)
0.019 nmi:nmi_handler:nmi_cpu_backtrace_handler() delta_ns: 2907 handled: 0)
0.676 nmi:nmi_handler:perf_event_nmi_handler() delta_ns: 9401 handled: 1)
0.680 nmi:nmi_handler:nmi_cpu_backtrace_handler() delta_ns: 288 handled: 0)
0.701 nmi:nmi_handler:perf_event_nmi_handler() delta_ns: 4977 handled: 1)
0.703 nmi:nmi_handler:nmi_cpu_backtrace_handler() delta_ns: 67 handled: 0)
0.736 nmi:nmi_handler:perf_event_nmi_handler() delta_ns: 8549 handled: 1)
^C#
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexis Berlemont <alexis.berlemont@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1492063332-5745-1-git-send-email-ravi.bangoria@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
(This is a patch has been sitting in the Intel CQM/CMT driver series for
a while, despite not depend on it. Sending it now independently since
the series is being discarded.)
When an event is in error state, read() returns 0 instead of sizeof()
buffer. In certain modes, such as interval printing, ignoring the 0
return value may cause bogus count deltas to be computed and thus
invalid results printed.
This patch fixes this problem by modifying read_counters() to mark the
event as not scaled (scaled = -1) to force the printout routine to show
<NOT COUNTED>.
Signed-off-by: Stephane Eranian <eranian@google.com>
Reviewed-by: David Carrillo-Cisneros <davidcc@google.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/20170412182301.44406-1-davidcc@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The I2C device ID entries set a .driver_data but this data is never
looked up by the driver. So don't set it and also remove the enum.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The switch that conditionally sets CPUPOWER_CAP_HAS_TURBO_RATIO and
CPUPOWER_CAP_IS_SNB flags is missing a break, so all cores get both
flags set and an assumed base clock of 100 MHz for turbo values.
Reported-by: GSR <gsr.bugs@infernal-iceberg.com>
Tested-by: GSR <gsr.bugs@infernal-iceberg.com>
References: https://bugs.debian.org/859978
Fixes: 8fb2e440b223 (cpupower: Show Intel turbo ratio support via ...)
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat utility fixes for v4.11 from Len Brown.
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: update version number
tools/power turbostat: fix impossibly large CPU%c1 value
tools/power turbostat: turbostat.8 add missing column definitions
tools/power turbostat: update HWP dump to decimal from hex
tools/power turbostat: enable package THERM_INTERRUPT dump
tools/power turbostat: show missing Core and GFX power on SKL and KBL
tools/power turbostat: bugfix: GFXMHz column not changing
|
|
There are two bugs in the follow-MAC code:
* it treats the radiotap header as the 802.11 header
(therefore it can't possibly work)
* it doesn't verify that the skb data it accesses is actually
present in the header, which is mitigated by the first point
Fix this by moving all of this out into a separate function.
This function copies the data it needs using skb_copy_bits()
to make sure it can be accessed if it's paged, and offsets
that by the possibly present vendor radiotap header.
This also makes all those conditions more readable.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The snd_use_lock_sync() (thus its implementation
snd_use_lock_sync_helper()) has the 5 seconds timeout to break out of
the sync loop. It was introduced from the beginning, just to be
"safer", in terms of avoiding the stupid bugs.
However, as Ben Hutchings suggested, this timeout rather introduces a
potential leak or use-after-free that was apparently fixed by the
commit 2d7d54002e39 ("ALSA: seq: Fix race during FIFO resize"):
for example, snd_seq_fifo_event_in() -> snd_seq_event_dup() ->
copy_from_user() could block for a long time, and snd_use_lock_sync()
goes timeout and still leaves the cell at releasing the pool.
For fixing such a problem, we remove the break by the timeout while
still keeping the warning.
Suggested-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch utilizes the new PLL clk notifier to gate then ungate the
PLL CPU clock after rate changes. This should mitigate the system
hangs observed after the introduction of cpufreq for the A33.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
In common PLL designs, changes to the dividers take effect almost
immediately, while changes to the multipliers (implemented as
dividers in the feedback loop) take a few cycles to work into
the feedback loop for the PLL to stablize.
Sometimes when the PLL clock rate is changed, the decrease in the
divider is too much for the decrease in the multiplier to catch up.
The PLL clock rate will spike, and in some cases, might lock up
completely. This is especially the case if the divider changed is
the pre-divider, which affects the reference frequency.
This patch introduces a clk notifier callback that will gate and
then ungate a clk after a rate change, effectively resetting it,
so it continues to work, despite any possible lockups. Care must
be taken to reparent any consumers to other temporary clocks during
the rate change, and that this notifier callback must be the first
to be registered.
This is intended to fix occasional lockups with cpufreq on newer
Allwinner SoCs, such as the A33 and the H3. Previously it was
thought that reparenting the cpu clock away from the PLL while
it stabilized was enough, as this worked quite well on the A31.
On the A33, hangs have been observed after cpufreq was recently
introduced. With the H3, a more thorough test [1] showed that
reparenting alone isn't enough. The system still locks up unless
the dividers are limited to 1.
A hunch was if the PLL was stuck in some unknown state, perhaps
gating then ungating it would bring it back to normal. Tests
done by Icenowy Zheng using Ondrej's test firmware shows this
to be a valid solution.
[1] http://www.spinics.net/lists/arm-kernel/msg552501.html
Reported-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The ccu-sun9i-a80 driver uses the ccu_mult_ops struct, but unlike the other
users it doesen't select the corresponding Kconfig symbol under which the
struct is compiled in.
This results in the following link error with CONFIG_SUN9I_A80_CCU=y and
CONFIG_SUNXI_CCU_MULT=n:
drivers/built-in.o:(.data+0x2d638): undefined reference to 'ccu_mult_ops'
Fix this by explicitly selecting CONFIG_SUNXI_CCU_MULT like the other
users of the struct.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
With CONFIG_RESET_CONTROLLER=n we get the following link error in the
sunxi-ng clk driver:
drivers/built-in.o: In function `sunxi_ccu_probe':
mux-core.c:(.text+0x12fe68): undefined reference to 'reset_controller_register'
mux-core.c:(.text+0x12fe68): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'reset_controller_register'
Fix this by adding the appropriate select statement.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"i915, gvt, nouveau, udl and etnaviv fixes.
I was away the end of last week, so some of these would have been in
rc6, and it's Easter from tomorrow, so I decided I better dequeue what
I have now.
The nouveau changes, just add a hw enable for GP107 display (like a
pci id addition really), and fix a couple of regressions. i915 has
some more gvt fixes, along with a few run of the mill ones, the rcu
one seems like a few people have hit it.
Otherwise a small udl and small etnaviv fix"
* tag 'drm-fixes-for-v4.11-rc7' of git://people.freedesktop.org/~airlied/linux: (22 commits)
drm/etnaviv: fix missing unlock on error in etnaviv_gpu_submit()
drm/udl: Fix unaligned memory access in udl_render_hline
drm/i915: Don't call synchronize_rcu_expedited under struct_mutex
drm/i915: Suspend GuC prior to GPU Reset during GEM suspend
drm/nouveau: initial support (display-only) for GP107
drm/nouveau/kms/nv50: fix double dma_fence_put() when destroying plane state
drm/nouveau/kms/nv50: fix setting of HeadSetRasterVertBlankDmi method
drm/nouveau/mmu/nv4a: use nv04 mmu rather than the nv44 one
drm/nouveau/mpeg: mthd returns true on success now
drm/i915/gvt: set the correct default value of CTX STATUS PTR
drm/i915/gvt: Fix firmware loading interface for GVT-g golden HW state
drm/i915: Use a dummy timeline name for a signaled fence
drm/i915: Ironlake do_idle_maps w/a may be called w/o struct_mutex
drm/i915/gvt: remove the redundant info NULL check
drm/i915/gvt: adjust mem size for low resolution type
drm/i915: Avoid lock dropping between rescheduling
drm/i915/gvt: exclude cfg space from failsafe mode
drm/i915/gvt: Activate/de-activate vGPU in mdev ops.
drm/i915/execlists: Wrap tail pointer after reset tweaking
drm/i915/perf: remove user triggerable warn
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm fixes from Thierry Reding:
"This contain a fix for the atomic update support recently added to
the Rockchip driver where the clock reference count would become
unbalanced and result in the clock feeding the PWM to always be
disabled.
Another fix to the Intel LPSS driver that adds an update bit quirk
required for a specific configuration"
* tag 'pwm/for-4.11-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: rockchip: State of PWM clock should synchronize with PWM enabled state
pwm: lpss: Set enable-bit before waiting for update-bit to go low
pwm: lpss: Split Tangier configuration
|
|
Reserving a runtime region results in splitting the EFI memory
descriptors for the runtime region. This results in runtime region
descriptors with bogus memory mappings, leading to interesting crashes
like the following during a kexec:
general protection fault: 0000 [#1] SMP
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.11.0-rc1 #53
Hardware name: Wiwynn Leopard-Orv2/Leopard-DDR BW, BIOS LBM05 09/30/2016
RIP: 0010:virt_efi_set_variable()
...
Call Trace:
efi_delete_dummy_variable()
efi_enter_virtual_mode()
start_kernel()
? set_init_arg()
x86_64_start_reservations()
x86_64_start_kernel()
start_cpu()
...
Kernel panic - not syncing: Fatal exception
Runtime regions will not be freed and do not need to be reserved, so
skip the memmap modification in this case.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: <stable@vger.kernel.org> # v4.9+
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Dave Young <dyoung@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Jones <pjones@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 8e80632fb23f ("efi/esrt: Use efi_mem_reserve() and avoid a kmalloc()")
Link: http://lkml.kernel.org/r/20170412152719.9779-2-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Commit 10c7e20b2ff3 (ACPI / scan: fix enumeration (visited) flags for
bus rescans) attempted to fix a problem with ACPI-based enumerateion
of I2C/SPI devices, but it forgot to ensure that the visited flag
will be set for all of the other enumerated devices, so fix that.
Fixes: 10c7e20b2ff3 (ACPI / scan: fix enumeration (visited) flags for bus rescans)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194885
Reported-and-tested-by: Kevin Locke <kevin@kevinlocke.name>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 4.8+ <stable@vger.kernel.org> # 4.8+
|
|
/sys/firmware/acpi/hotplug/force_remove was presumably added to support
auto offlining in the past. This is, however, inherently dangerous for
some hotplugable resources like memory. The memory offlining fails when
the memory is still in use and cannot be dropped or migrated. If we
ignore the failure we are basically allowing for subtle memory
corruption or a crash.
We have actually noticed the later while hitting BUG() during the memory
hotremove (remove_memory):
ret = walk_memory_range(PFN_DOWN(start), PFN_UP(start + size - 1), NULL,
check_memblock_offlined_cb);
if (ret)
BUG();
it took us quite non-trivial time realize that the customer had
force_remove enabled. Even if the BUG was removed here and we could
propagate the error up the call chain it wouldn't help at all because
then we would hit a crash or a memory corruption later and harder to
debug. So force_remove is unfixable for the memory hotremove. We haven't
checked other hotplugable resources to be prone to a similar problems.
Remove the force_remove functionality because it is not fixable currently.
Keep the sysfs file and report an error if somebody tries to enable it.
Encourage users to report about the missing functionality and work with
them with an alternative solution.
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The schedutil governor reduces frequencies too fast in some
situations which cases undesirable performance drops to
appear.
To address that issue, make schedutil reduce the frequency slower by
setting it to the average of the value chosen during the previous
iteration of governor computations and the new one coming from its
frequency selection formula.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194963
Reported-by: John <john.ettedgui@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
There is a report that after commit 27622b061eb4 ("cpufreq: Convert
to hotplug state machine"), the normal CPU offline/online cycle
fails on some platforms.
According to the ftrace result, this problem was triggered on
platforms using acpi-cpufreq as the default cpufreq driver,
and due to the lack of some ACPI freq method (eg. _PCT),
cpufreq_online() failed and returned a negative value, so the CPU
hotplug state machine rolled back the CPU online process. Actually,
from the user's perspective, the failure of cpufreq_online() should
not prevent that CPU from being brought up, although cpufreq might
not work on that CPU.
BTW, during system startup cpufreq_online() is not invoked via CPU
online but by the cpufreq device creation process, so the APs can be
brought up even though cpufreq_online() fails in that stage.
This patch ignores the return value of cpufreq_online/offline() and
lets the cpufreq framework deal with the failure. cpufreq_online()
itself will do a proper rollback in that case and if _PCT is missing,
the ACPI cpufreq driver will print a warning if the corresponding
debug options have been enabled.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=194581
Fixes: 27622b061eb4 ("cpufreq: Convert to hotplug state machine")
Reported-and-tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.9+ <stable@vger.kernel.org> # 4.9+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Most CPUs do not have a hardware c1 counter,
and so turbostat derives c1 residency:
c1 = TSC - MPERF - other_core_cstate_counters
As it is not possible to atomically read these coutners,
measurement jitter can case this calcuation to "go negative"
when very close to 0. Turbostat detect that case and
simply prints c1 = 0.00%
But that check neglected to account for systems where the TSC
crystal clock domain and the MPERF BCLK domain are differ by
a small amount. That allowed very small negative c1 numbers
to escape this check and be printed as huge positve numbers.
This code begs for a bit of cleanup, but this patch
is the minimal change to fix the issue.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add GFX%rc6 and GFXMHz to the column descriptions section
of the turbostat man page.
Signed-off-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Syntax only.
The HWP CAPABILTIES and REQUEST ratios are more easily
viewed in decimal -- just multiply by 100 and you get MHz...
new:
cpu0: MSR_HWP_CAPABILITIES: 0x010c1b23 (high 35 guar 27 eff 12 low 1)
cpu0: MSR_HWP_REQUEST: 0x80002301 (min 1 max 35 des 0 epp 0x80 window 0x0 pkg 0x0)
old:
cpu0: MSR_HWP_CAPABILITIES: 0x010c1b23 (high 0x23 guar 0x1b eff 0xc low 0x1)
cpu0: MSR_HWP_REQUEST: 0x80002301 (min 0x1 max 0x23 des 0x0 epp 0x80 window 0x0 pkg 0x0)
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
cpu0: MSR_IA32_TEMPERATURE_TARGET: 0x00641400 (100 C)
cpu0: MSR_IA32_PACKAGE_THERM_STATUS: 0x884b0800 (25 C)
cpu0: MSR_IA32_PACKAGE_THERM_INTERRUPT: 0x00000003 (100 C, 100 C)
Enable the same per-core output, but hide it behind --debug
because it is too verbose on big systems.
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
While the current SDM is silent on the matter, the Core and GFX
RAPL power meters on SKL and KBL appear to work -- so show them.
Reported-by: Yaroslav Isakov <yaroslav.isakov@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
GP107 modesetting support (just recognising the chipset, no other changes until 4.12)
a couple of regression fixes, one of them a rather serious double-free issue that appeared in 4.10.
* 'linux-4.11' of git://github.com/skeggsb/linux:
drm/nouveau: initial support (display-only) for GP107
drm/nouveau/kms/nv50: fix double dma_fence_put() when destroying plane state
drm/nouveau/kms/nv50: fix setting of HeadSetRasterVertBlankDmi method
drm/nouveau/mmu/nv4a: use nv04 mmu rather than the nv44 one
drm/nouveau/mpeg: mthd returns true on success now
|
|
git://anongit.freedesktop.org/git/drm-intel into drm-fixes
drm/i915 fixes for v4.11-rc7
one rcu related fix, and a few GVT fixes.
* tag 'drm-intel-fixes-2017-04-12' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Don't call synchronize_rcu_expedited under struct_mutex
drm/i915: Suspend GuC prior to GPU Reset during GEM suspend
drm/i915/gvt: set the correct default value of CTX STATUS PTR
drm/i915/gvt: Fix firmware loading interface for GVT-g golden HW state
drm/i915: Use a dummy timeline name for a signaled fence
drm/i915: Ironlake do_idle_maps w/a may be called w/o struct_mutex
drm/i915/gvt: remove the redundant info NULL check
drm/i915/gvt: adjust mem size for low resolution type
drm/i915: Avoid lock dropping between rescheduling
drm/i915/gvt: exclude cfg space from failsafe mode
drm/i915/gvt: Activate/de-activate vGPU in mdev ops.
drm/i915/execlists: Wrap tail pointer after reset tweaking
drm/i915/perf: remove user triggerable warn
drm/i915/perf: destroy stream on sample_flags mismatch
drm/i915: Align "unfenced" tiled access on gen2, early gen3
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-fixes
drm-misc-fixes for 2017-04-11
Core changes:
- None
Driver changes
- udl: Fix unaligned memory access on SPARC (Jonathan)
* tag 'drm-misc-fixes-2017-04-11' of git://anongit.freedesktop.org/git/drm-misc:
drm/udl: Fix unaligned memory access in udl_render_hline
|
|
into drm-fixes
Single etnaviv error path fix.
* 'etnaviv/fixes' of https://git.pengutronix.de/git/lst/linux:
drm/etnaviv: fix missing unlock on error in etnaviv_gpu_submit()
|
|
With commit 23dac14d058f ("MIPS: PCI: Use struct list_head lists") new
controllers are added after the specified head where they where added
before the specified head previously.
Use list_add_tail to restore the former order.
This patches fixes the following PCI error on lantiq:
pci 0000:01:00.0: BAR 0: error updating (0x1c000004 != 0x000000)
Fixes: 23dac14d058f ("MIPS: PCI: Use struct list_head lists")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15808/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Commit fdd3d8ce0ea62 ("x86/dump_pagetables: Add support for 5-level
paging") introduced an error for dumping with only 4 levels by setting
PGD_LEVEL_MULT to a wrong value.
This is leading to e.g. addresses printed as "(null)" for ranges:
x86/mm: Found insecure W+X mapping at address (null)/(null)
Make PGD_LEVEL_MULT a multiple of PTRS_PER_P4D instead of PTRS_PER_PUD
Fixes: fdd3d8ce0ea62 ("x86/dump_pagetables: Add support for 5-level paging")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: http://lkml.kernel.org/r/20170412143634.6846-1-jgross@suse.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Before we rework the "pmem api" to stop abusing __copy_user_nocache()
for memcpy_to_pmem() we need to fix cases where we may strand dirty data
in the cpu cache. The problem occurs when copy_from_iter_pmem() is used
for arbitrary data transfers from userspace. There is no guarantee that
these transfers, performed by dax_iomap_actor(), will have aligned
destinations or aligned transfer lengths. Backstop the usage
__copy_user_nocache() with explicit cache management in these unaligned
cases.
Yes, copy_from_iter_pmem() is now too big for an inline, but addressing
that is saved for a later patch that moves the entirety of the "pmem
api" into the pmem driver directly.
Fixes: 5de490daec8b ("pmem: add copy_from_iter_pmem() and clear_pmem()")
Cc: <stable@vger.kernel.org>
Cc: <x86@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The following warning triggers with a new unit test that stresses the
device-dax interface.
===============================
[ ERR: suspicious RCU usage. ]
4.11.0-rc4+ #1049 Tainted: G O
-------------------------------
./include/linux/rcupdate.h:521 Illegal context switch in RCU read-side critical section!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 0
2 locks held by fio/9070:
#0: (&mm->mmap_sem){++++++}, at: [<ffffffff8d0739d7>] __do_page_fault+0x167/0x4f0
#1: (rcu_read_lock){......}, at: [<ffffffffc03fbd02>] dax_dev_huge_fault+0x32/0x620 [dax]
Call Trace:
dump_stack+0x86/0xc3
lockdep_rcu_suspicious+0xd7/0x110
___might_sleep+0xac/0x250
__might_sleep+0x4a/0x80
__alloc_pages_nodemask+0x23a/0x360
alloc_pages_current+0xa1/0x1f0
pte_alloc_one+0x17/0x80
__pte_alloc+0x1e/0x120
__get_locked_pte+0x1bf/0x1d0
insert_pfn.isra.70+0x3a/0x100
? lookup_memtype+0xa6/0xd0
vm_insert_mixed+0x64/0x90
dax_dev_huge_fault+0x520/0x620 [dax]
? dax_dev_huge_fault+0x32/0x620 [dax]
dax_dev_fault+0x10/0x20 [dax]
__do_fault+0x1e/0x140
__handle_mm_fault+0x9af/0x10d0
handle_mm_fault+0x16d/0x370
? handle_mm_fault+0x47/0x370
__do_page_fault+0x28c/0x4f0
trace_do_page_fault+0x58/0x2a0
do_async_page_fault+0x1a/0xa0
async_page_fault+0x28/0x30
Inserting a page table entry may trigger an allocation while we are
holding a read lock to keep the device instance alive for the duration
of the fault. Use srcu for this keep-alive protection.
Fixes: dee410792419 ("/dev/dax, core: file operations and dax-mmap")
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
