| Age | Commit message (Collapse) | Author |
|---|
|
If the cacheline may still be busy, atomically mark it for future
release, and only if we can determine that it will never be used again,
immediately free it.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1392
Fixes: ebece7539242 ("drm/i915: Keep timeline HWSP allocated until idle across the system")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.2+
Link: https://patchwork.freedesktop.org/patch/msgid/20200306154647.3528345-1-chris@chris-wilson.co.uk
(cherry picked from commit 2d4bd971f5baa51418625f379a69f5d58b5a0450)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
If we stop filling the ELSP due to an incompatible virtual engine
request, check if we should enable the timeslice on behalf of the queue.
This fixes the case where we are inspecting the last->next element when
we know that the last element is the last request in the execution queue,
and so decided we did not need to enable timeslicing despite the intent
to do so!
Fixes: 8ee36e048c98 ("drm/i915/execlists: Minimalistic timeslicing")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org> # v5.4+
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306113012.3184606-1-chris@chris-wilson.co.uk
(cherry picked from commit 3df2deed411e0f1b7312baf0139aab8bba4c0410)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
The alignment is u64, and yet is_power_of_2() assumes unsigned long,
which might give different results between 32b and 64b kernel.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305203534.210466-1-matthew.auld@intel.com
Cc: stable@vger.kernel.org
(cherry picked from commit 2920516b2f719546f55079bc39a7fe409d9e80ab)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Commit c3b5a8430daad ("drm/i915/gvt: Enable gfx virtualiztion for CFL")
added the support on CFL. The vgpu emulation hotplug support on CFL was
supposed to be included in that patch. Without the vgpu emulation
hotplug support, the dma-buf based display gives us a blur face.
So fix this issue by adding the vgpu emulation hotplug support on CFL.
Fixes: c3b5a8430daad ("drm/i915/gvt: Enable gfx virtualiztion for CFL")
Signed-off-by: Tina Zhang <tina.zhang@intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200227010041.32248-1-tina.zhang@intel.com
(cherry picked from commit 135dde8853c7e00f6002e710f7e4787ed8585c0e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Requests within a timeline are ordered by that timeline, so awaiting for
the start of a request within the timeline is a no-op. This used to work
by falling out of the mutex_trylock() as the signaler and waiter had the
same timeline and not returning an error.
Fixes: 6a79d848403d ("drm/i915: Lock signaler timeline while navigating")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.5+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305134822.2750496-1-chris@chris-wilson.co.uk
(cherry picked from commit ab7a69020fb5d5c7ba19fba60f62fd6f9ca9f779)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Fix the inverted test to emit the wait on the end of the previous
request if we /haven't/ already.
Fixes: 6a79d848403d ("drm/i915: Lock signaler timeline while navigating")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.5+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305104210.2619967-1-chris@chris-wilson.co.uk
(cherry picked from commit 07e9c59d63df6a1c44c1975c01827ba18b69270a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Clang warns:
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:2860:9: warning:
converting the result of '?:' with integer constants to a boolean always
evaluates to 'true' [-Wtautological-constant-compare]
return DPAA_FD_DATA_ALIGNMENT ? ALIGN(headroom,
^
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:131:34: note: expanded
from macro 'DPAA_FD_DATA_ALIGNMENT'
\#define DPAA_FD_DATA_ALIGNMENT (fman_has_errata_a050385() ? 64 : 16)
^
1 warning generated.
This was exposed by commit 3c68b8fffb48 ("dpaa_eth: FMan erratum A050385
workaround") even though it appears to have been an issue since the
introductory commit 9ad1a3749333 ("dpaa_eth: add support for DPAA
Ethernet") since DPAA_FD_DATA_ALIGNMENT has never been able to be zero.
Just replace the whole boolean expression with the true branch, as it is
always been true.
Link: https://github.com/ClangBuiltLinux/linux/issues/928
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull fscrypt fix from Eric Biggers:
"Fix a bug where if userspace is writing to encrypted files while the
FS_IOC_REMOVE_ENCRYPTION_KEY ioctl (introduced in v5.4) is running,
dirty inodes could be evicted, causing writes could be lost or the
filesystem to hang due to a use-after-free. This was encountered
during real-world use, not just theoretical.
Tested with the existing fscrypt xfstests, and with a new xfstest I
wrote to reproduce this bug. This fix does expose an existing bug with
'-o lazytime' that Ted is working on fixing, but this fix is more
critical and needed anyway regardless of the lazytime fix"
* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt:
fscrypt: don't evict dirty inodes after removing key
|
|
Those files got moved, but cross-references still point to the
wrong places.
Fixes: fcd680727157 ("Documentation: Add io-mapping.rst to driver-api manual")
Fixes: d1ce350015d8 ("Documentation: Add io_ordering.rst to driver-api manual")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Alex Shi <alex.shi@linux.alibaba.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/c0205119db4fef536272cb0a183b6c14c2c8bf4c.1583927470.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into spi-5.7
spi: Rewrite mtk-quadspi spi-nor driver with spi-mem
This patchset from Chuanhong Guo <gch981213@gmail.com> adds a spi-mem
driver for Mediatek SPI-NOR controller, which already has limited
support by mtk-quadspi. This new driver can make use of full quadspi
capability of this controller.
|
|
This driver is superseded by the new spi-mtk-nor driver.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200306085052.28258-5-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
spi-mtk-nor is a driver to replace mtk-quadspi and they have almost
the same device-tree bindings. Reuse this binding documentation and
convert it for new driver:
1. "Mediatek SoCs" -> "Mediatek ARM SoCs" because MTK MIPS SoCs
use different controllers.
2. document "interrupts" as a required property because it's
available on all SoCs with this controller and new driver takes
advantages of it. It's implemented as optional only to maintain
backward compatibility.
3. add a dummy interrupt binding in example.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200306085052.28258-4-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This is a driver for mtk spi-nor controller using spi-mem interface.
The same controller already has limited support provided by mtk-quadspi
driver under spi-nor framework and this new driver is a replacement
for the old one.
Comparing to the old driver, this driver has following advantages:
1. It can handle any full-duplex spi transfer up to 6 bytes, and
this is implemented using generic spi interface.
2. It take account into command opcode properly. The reading routine
in this controller can only use 0x03 or 0x0b as opcode on 1-1-1
transfers, but old driver doesn't implement this properly. This
driver checks supported opcode explicitly and use (1) to perform
unmatched operations.
3. It properly handles SFDP reading. Old driver can't read SFDP
due to the bug mentioned in (2).
4. It can do 1-2-2 and 1-4-4 fast reading on spi-nor. These two ops
requires parsing SFDP, which isn't possible in old driver. And
the old driver is only flagged to support 1-1-2 mode.
5. It takes advantage of the DMA feature in this controller for
long reads and supports IRQ on DMA requests to free cpu cycles
from polling status registers on long DMA reading. It achieves
up to 17.5MB/s reading speed (1-4-4 mode) which is way faster
than the old one. IRQ is implemented as optional to maintain
backward compatibility.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200306085052.28258-3-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We only need a spi-max-frequency when we specifically request a
spi frequency lower than the max speed of spi host.
This property is already documented as optional property and current
host drivers are implemented to operate at highest speed possible
when spi->max_speed_hz is 0.
This patch makes spi-max-frequency an optional property so that
we could just omit it to use max controller speed.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200306085052.28258-2-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A couple of fixes:
* three netlink validation fixes
* a mesh path selection fix
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By selecting MTD_SPI_NOR for SPI_HISI_SFC_V3XX, we may introduce unmet
dependencies:
WARNING: unmet direct dependencies detected for MTD_SPI_NOR
Depends on [m]: MTD [=m] && SPI_MASTER [=y]
Selected by [y]:
- SPI_HISI_SFC_V3XX [=y] && SPI [=y] && SPI_MASTER [=y] && (ARM64 && ACPI [=y] || COMPILE_TEST [=y]) && HAS_IOMEM [=y]
Since MTD_SPI_NOR is only selected by SPI_HISI_SFC_V3XX for practical
reasons - slave devices use the spi-nor driver, enabled by MTD_SPI_NOR -
just drop it.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1583948115-239907-1-git-send-email-john.garry@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Binderfs binder-control devices are cleaned up via binderfs_evict_inode
too() which will use refcount_dec_and_test(). However, we missed to set
the refcount for binderfs binder-control devices and so we underflowed
when the binderfs instance got unmounted. Pretty obvious oversight and
should have been part of the more general UAF fix. The good news is that
having test cases (suprisingly) helps.
Technically, we could detect that we're about to cleanup the
binder-control dentry in binderfs_evict_inode() and then simply clean it
up. But that makes the assumption that the binder driver itself will
never make use of a binderfs binder-control device after the binderfs
instance it belongs to has been unmounted and the superblock for it been
destroyed. While it is unlikely to ever come to this let's be on the
safe side. Performance-wise this also really doesn't matter since the
binder-control device is only every really when creating the binderfs
filesystem or creating additional binder devices. Both operations are
pretty rare.
Fixes: f0fe2c0f050d ("binder: prevent UAF for binderfs devices II")
Link: https://lore.kernel.org/r/CA+G9fYusdfg7PMfC9Xce-xLT7NiyKSbgojpK35GOm=Pf9jXXrA@mail.gmail.com
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Todd Kjos <tkjos@google.com>
Link: https://lore.kernel.org/r/20200311105309.1742827-1-christian.brauner@ubuntu.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Ensure we keep the truncated value, if we did truncate it. If not, we
might read/write more than the registered buffer size.
Also for retry, ensure that we return the truncated mapped value for
the vectorized versions of the read/write commands.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The default defintions use fill pattern 0x90 for padding which for ARC
generates unintended "ldh_s r12,[r0,0x20]" corresponding to opcode 0x9090
So use ".align 4" which insert a "nop_s" instruction instead.
Cc: stable@vger.kernel.org
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Before
------
| CPU: 1 PID: 29061 Comm: tst-dynarray-at Not tainted 5.6.0-rc1-00002-g941fcc018ca6-dirty #12
|
| [ECR ]: 0x00090000 =>
| [EFA ]: 0x00000000
| [ERET ]: 0x2004aa6c
| @off 0x2aa6c in [/lib/libc-2.31.9000.so]
VMA: 0x20020000 to 0x20122000
| [STAT32]: 0x80080a82 [IE U ]
| BTA: 0x2004aa18 SP: 0x5ffff8a8 FP: 0x5ffff8fc
| LPS: 0x2008788e LPE: 0x20087896 LPC: 0x00000000
| r00: 0x00000000 r01: 0x5ffff8a8 r02: 0x00000000
| r03: 0x00000008 r04: 0xffffffff r05: 0x00000000
| r06: 0x00000000 r07: 0x00000000 r08: 0x00000087
| r09: 0x00000000 r10: 0x2010691c r11: 0x00000020
| r12: 0x2003b214 r13: 0x5ffff8a8 r14: 0x20126e68
| r15: 0x2001f26c r16: 0x2012a000 r17: 0x00000001
| r18: 0x5ffff8fc r19: 0x00000000 r20: 0x5ffff948
| r21: 0x00000001 r22: 0xffffffff r23: 0x5fffff8c
| r24: 0x4008c2a8 r25: 0x2001f6e0
After
-----
| CPU: 1 PID: 29061 Comm: tst-dynarray-at Not tainted 5.6.0-rc1-00002-g941fcc018ca6-dirty #12
| @off 0x2aa6c in [/lib/libc-2.31.9000.so] VMA: 0x20020000 to 0x20122000
| ECR: 0x00090000 EFA: 0x00000000 ERET: 0x2004aa6c
| STAT32: 0x80080a82 [IE U ] BTA: 0x2004aa18
| BLK: 0x2003b214 SP: 0x5ffff8a8 FP: 0x5ffff8fc
| LPS: 0x2008788e LPE: 0x20087896 LPC: 0x00000000
| r00: 0x00000000 r01: 0x5ffff8a8 r02: 0x00000000
| r03: 0x00000008 r04: 0xffffffff r05: 0x00000000
| r06: 0x00000000 r07: 0x00000000 r08: 0x00000087
| r09: 0x00000000 r10: 0x2010691c r11: 0x00000020
| r12: 0x2003b214 r13: 0x5ffff8a8 r14: 0x20126e68
| r15: 0x2001f26c r16: 0x2012a000 r17: 0x00000001
| r18: 0x5ffff8fc r19: 0x00000000 r20: 0x5ffff948
| r21: 0x00000001 r22: 0xffffffff r23: 0x5fffff8c
| r24: 0x4008c2a8 r25: 0x2001f6e0 BTA: 0x2004aa18
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull thread fix from Christian Brauner:
"This contains a single fix for a regression which was introduced when
we introduced the ability to select a specific pid at process creation
time.
When this feature is requested, the error value will be set to -EPERM
after exiting the pid allocation loop. This caused EPERM to be
returned when e.g. the init process/child subreaper of the pid
namespace has already died where we used to return ENOMEM before.
The first patch here simply fixes the regression by unconditionally
setting the return value back to ENOMEM again once we've successfully
allocated the requested pid number. This should be easy to backport to
v5.5.
The second patch adds a comment explaining that we must keep returning
ENOMEM since we've been doing it for a long time and have explicitly
documented this behavior for userspace. This seemed worthwhile because
we now have at least two separate example where people tried to change
the return value to something other than ENOMEM (The first version of
the regression fix did that too and the commit message links to an
earlier patch that tried to do the same.).
I have a simple regression test to make sure we catch this regression
in the future but since that introduces a whole new selftest subdir
and test files I'll keep this for v5.7"
* tag 'for-linus-2020-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
pid: make ENOMEM return value more obvious
pid: Fix error return value in some cases
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull ftrace fix from Steven Rostedt:
"Have ftrace lookup_rec() return a consistent record otherwise it can
break live patching"
* tag 'trace-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Return the first found result in lookup_rec()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Thomas Bogendoerfer:
"A few MIPS fixes:
- DT fixes for CI20
- Fix command line handling
- Correct patchwork URL"
* tag 'mips_fixes_5.6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MAINTAINERS: Correct MIPS patchwork URL
MIPS: DTS: CI20: fix interrupt for pcf8563 RTC
MIPS: DTS: CI20: fix PMU definitions for ACT8600
MIPS: Fix CONFIG_MIPS_CMDLINE_DTB_EXTEND handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Some pin control fixes for the v5.6 series.
It comes down to memory leaks in the core and driver fixes. Some
should have been sent earlier but they kept piling up and the world is
just so full of distractions these days.
- Fix some inverted pins in the Meson GLX driver.
- Align the i.MX SC message structs causing warnings from KASan.
- Balance the kref in pinctrl hogs so they are actually free:d when
removing a pin control module. We haven't seen it before as people
don't use modules for pin control that much, I think.
- Add a missing call to pinctrl_unregister_mappings() another memory
leak when using modules.
- Fix the fwspec parsing in the Qualcomm driver.
- Fix a syntax error in the Falcon driver.
- Assign .irq_eoi conditionally in the Qualcomm driver, fixing a bug
affecting elder Qualcomm platforms"
* tag 'pinctrl-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: qcom: Assign irq_eoi conditionally
pinctrl: falcon: fix syntax error
pinctrl: qcom: ssbi-gpio: Fix fwspec parsing bug
pinctrl: madera: Add missing call to pinctrl_unregister_mappings
pinctrl: core: Remove extra kref_get which blocks hogs being freed
pinctrl: imx: scu: Align imx sc msg structs to 4
pinctrl: meson-gxl: fix GPIOX sdio pins
|
|
This does three inter-related things to clarify the usage of the
platform device dma_mask field. In the process, fix the bug introduced
by cdfee5623290 ("driver core: initialize a default DMA mask for
platform device") that caused Artem Tashkinov's laptop to not boot with
newer Fedora kernels.
This does:
- First off, rename the field to "platform_dma_mask" to make it
greppable.
We have way too many different random fields called "dma_mask" in
various data structures, where some of them are actual masks, and
some of them are just pointers to the mask. And the structures all
have pointers to each other, or embed each other inside themselves,
and "pdev" sometimes means "platform device" and sometimes it means
"PCI device".
So to make it clear in the code when you actually use this new field,
give it a unique name (it really should be something even more unique
like "platform_device_dma_mask", since it's per platform device, not
per platform, but that gets old really fast, and this is unique
enough in context).
To further clarify when the field gets used, initialize it when we
actually start using it with the default value.
- Then, use this field instead of the random one-off allocation in
platform_device_register_full() that is now unnecessary since we now
already have a perfectly fine allocation for it in the platform
device structure.
- The above then allows us to fix the actual bug, where the error path
of platform_device_register_full() would unconditionally free the
platform device DMA allocation with 'kfree()'.
That kfree() was dont regardless of whether the allocation had been
done earlier with the (now removed) kmalloc, or whether
setup_pdev_dma_masks() had already been used and the dma_mask pointer
pointed to the mask that was part of the platform device.
It seems most people never triggered the error path, or only triggered
it from a call chain that set an explicit pdevinfo->dma_mask value (and
thus caused the unnecessary allocation that was "cleaned up" in the
error path) before calling platform_device_register_full().
Robin Murphy points out that in Artem's case the wdat_wdt driver failed
in platform_device_add(), and that was the one that had called
platform_device_register_full() with pdevinfo.dma_mask = 0, and would
have caused that kfree() of pdev.dma_mask corrupting the heap.
A later unrelated kmalloc() then oopsed due to the heap corruption.
Fixes: cdfee5623290 ("driver core: initialize a default DMA mask for platform device")
Reported-bisected-and-tested-by: Artem S. Tashkinov <aros@gmx.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add the new A33 SS compatible to the crypto node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
It has turned out that the sdhci-tegra controller requires the R1B response,
for commands that has this response associated with them. So, converting
from an R1B to an R1 response for a CMD6 for example, leads to problems
with the HW busy detection support.
Fix this by informing the mmc core about the requirement, via setting the
host cap, MMC_CAP_NEED_RSP_BUSY.
Reported-by: Bitan Biswas <bbiswas@nvidia.com>
Reported-by: Peter Geis <pgwipeout@gmail.com>
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Tested-By: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The A33 SS has a difference with all other SS, it give SHA1 digest
directly in BE.
This difference need to be handlded by the driver and so need a new
compatible.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
It has turned out that the sdhci-omap controller requires the R1B response,
for commands that has this response associated with them. So, converting
from an R1B to an R1 response for a CMD6 for example, leads to problems
with the HW busy detection support.
Fix this by informing the mmc core about the requirement, via setting the
host cap, MMC_CAP_NEED_RSP_BUSY.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Reported-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: <stable@vger.kernel.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The busy timeout that is computed for each erase/trim/discard operation,
can become quite long and may thus exceed the host->max_busy_timeout. If
that becomes the case, mmc_do_erase() converts from using an R1B response
to an R1 response, as to prevent the host from doing HW busy detection.
However, it has turned out that some hosts requires an R1B response no
matter what, so let's respect that via checking MMC_CAP_NEED_RSP_BUSY. Note
that, if the R1B gets enforced, the host becomes fully responsible of
managing the needed busy timeout, in one way or the other.
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-By: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
It has turned out that some host controllers can't use R1B for CMD6 and
other commands that have R1B associated with them. Therefore invent a new
host cap, MMC_CAP_NEED_RSP_BUSY to let them specify this.
In __mmc_switch(), let's check the flag and use it to prevent R1B responses
from being converted into R1. Note that, this also means that the host are
on its own, when it comes to manage the busy timeout.
Suggested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Cc: <stable@vger.kernel.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Tested-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-By: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Commit aa23ca3d98f7 ("gpiolib: acpi: Add honor_wakeup module-option +
quirk mechanism") was added to deal with spurious wakeups on one specific
model of the HP x2 10 series. In the mean time I have learned that there
are at least 3 different HP x2 10 models:
Bay Trail SoC + AXP288 PMIC
Cherry Trail SoC + AXP288 PMIC
Cherry Trail SoC + TI PMIC
And the original quirk is only correct for (and only matches the)
Cherry Trail SoC + TI PMIC model.
The Bay Trail SoC + AXP288 PMIC model has different DMI strings, has
the external EC interrupt on a different GPIO pin and only needs to ignore
wakeups on the EC interrupt, the INT0002 device works fine on this model.
This commit adds an extra DMI based quirk for the HP x2 10 BYT + AXP288
model, ignoring wakeups for ACPI GPIO events on the EC interrupt pin
on this model. This fixes spurious wakeups from suspend on this model.
Fixes: aa23ca3d98f7 ("gpiolib: acpi: Add honor_wakeup module-option + quirk mechanism")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200302111225.6641-3-hdegoede@redhat.com
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit aa23ca3d98f7 ("gpiolib: acpi: Add honor_wakeup module-option +
quirk mechanism") was added to deal with spurious wakeups on one specific
model of the HP x2 10 series.
The approach taken there was to add a bool controlling wakeup support for
all ACPI GPIO events. This was sufficient for the specific HP x2 10 model
the commit was trying to fix, but in the mean time other models have
turned up which need a similar workaround to avoid spurious wakeups from
suspend, but only for one of the pins on which the ACPI tables request
ACPI GPIO events.
Since the honor_wakeup option was added to be able to ignore wake events,
the name was perhaps not the best, this commit renames it to ignore_wake
and changes it to a string with the following format:
gpiolib_acpi.ignore_wake=controller@pin[,controller@pin[,...]]
This allows working around spurious wakeup issues on a per pin basis.
This commit also reworks the existing quirk for the HP x2 10 so that
it functions as before.
Note:
-This removes the honor_wakeup parameter. This has only been upstream for
a short time and to the best of my knowledge there are no users using
this module parameter.
-The controller@pin[,controller@pin[,...]] syntax is based on an existing
kernel module parameter using the same controller@pin format. That version
uses ';' as separator, but in practice that is problematic because grub2
cannot handle this without taking special care to escape the ';', so here
we are using a ',' as separator instead which does not have this issue.
Fixes: aa23ca3d98f7 ("gpiolib: acpi: Add honor_wakeup module-option + quirk mechanism")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200302111225.6641-2-hdegoede@redhat.com
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit aa23ca3d98f7 ("gpiolib: acpi: Add honor_wakeup module-option +
quirk mechanism") added a quirk for some models of the HP x2 10 series.
There are 2 issues with the comment describing the quirk:
1) The comment claims the DMI quirk applies to all Cherry Trail based HP x2
10 models. In the mean time I have learned that there are at least 3
models of the HP x2 10 models:
Bay Trail SoC + AXP288 PMIC
Cherry Trail SoC + AXP288 PMIC
Cherry Trail SoC + TI PMIC
And this quirk's DMI matches only match the Cherry Trail SoC + TI PMIC
SoC, which is good because we want a slightly different quirk for the
others. This commit updates the comment to make it clear that the quirk
is only for the Cherry Trail SoC + TI PMIC models.
2) The comment says that it is ok to disable wakeup on all ACPI GPIO event
handlers, because there is only the one for the embedded-controller
events. This is not true, there also is a handler for the special
INT0002 device which is related to USB wakeups. We need to also disable
wakeups on that one because the device turns of the USB-keyboard built
into the dock when closing the lid. The XHCI controller takes a while
to notice this, so it only notices it when already suspended, causing
a spurious wakeup because of this. So disabling wakeup on all handlers
is the right thing to do, but not because there only is the one handler
for the EC events. This commit updates the comment to correctly reflect
this.
Fixes: aa23ca3d98f7 ("gpiolib: acpi: Add honor_wakeup module-option + quirk mechanism")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200302111225.6641-1-hdegoede@redhat.com
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The implementation if .irq_disable() which kicks in between
the gpiolib and the driver is not properly mimicking the
expected semantics of the irqchip core: the irqchip will
call .irq_disable() if that exists, else it will call
mask_irq() which first checks if .irq_mask() is defined
before calling it.
Since we are calling it unconditionally, we get this bug
from drivers/pinctrl/qcom/pinctrl-ssbi-gpio.c, as it only
defines .irq_mask_ack and not .irq_mask:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = (ptrval)
(...)
PC is at 0x0
LR is at gpiochip_irq_disable+0x20/0x30
Fix this by only calling .irq_mask() if it exists.
Cc: Brian Masney <masneyb@onstation.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Fixes: 461c1a7d4733 ("gpiolib: override irq_enable/disable")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200306132326.1329640-1-linus.walleij@linaro.org
|
|
The dmidecode program fails to properly decode the SMBIOS data supplied
by OVMF/UEFI when running in an SEV guest. The SMBIOS area, under SEV, is
encrypted and resides in reserved memory that is marked as EFI runtime
services data.
As a result, when memremap() is attempted for the SMBIOS data, it
can't be mapped as regular RAM (through try_ram_remap()) and, since
the address isn't part of the iomem resources list, it isn't mapped
encrypted through the fallback ioremap().
Add a new __ioremap_check_other() to deal with memory types like
EFI_RUNTIME_SERVICES_DATA which are not covered by the resource ranges.
This allows any runtime services data which has been created encrypted,
to be mapped encrypted too.
[ bp: Move functionality to a separate function. ]
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Tested-by: Joerg Roedel <jroedel@suse.de>
Cc: <stable@vger.kernel.org> # 5.3
Link: https://lkml.kernel.org/r/2d9e16eb5b53dc82665c95c6764b7407719df7a0.1582645327.git.thomas.lendacky@amd.com
|
|
When the SPI device nodes were added, they were added in the wrong
location in the device tree file. The device nodes should be sorted
by register address.
Move the devices node to their correct positions within the file.
Fixes: 554581b79139 ("ARM: dts: sun8i: R40: Add SPI controllers nodes and pinmuxes")
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
When the SPI device nodes were added, SPI2 and SPI3 had incorrect
register base addresses.
Fix the base address for both of them.
Fixes: 554581b79139 ("ARM: dts: sun8i: R40: Add SPI controllers nodes and pinmuxes")
Reported-by: JuanEsf <juanesf91@gmail.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
When the AHCI device node was added, it was added in the wrong location
in the device tree file. The device nodes should be sorted by register
address.
Move the device node to before EHCI1, where it belongs.
Fixes: 41c64d3318aa ("ARM: dts: sun8i: r40: add sata node")
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
It appears that ip ranges can overlap so. In that case lookup_rec()
returns whatever results it got last even if it found nothing in last
searched page.
This breaks an obscure livepatch late module patching usecase:
- load livepatch
- load the patched module
- unload livepatch
- try to load livepatch again
To fix this return from lookup_rec() as soon as it found the record
containing searched-for ip. This used to be this way prior lookup_rec()
introduction.
Link: http://lkml.kernel.org/r/20200306174317.21699-1-asavkov@redhat.com
Cc: stable@vger.kernel.org
Fixes: 7e16f581a817 ("ftrace: Separate out functionality from ftrace_location_range()")
Signed-off-by: Artem Savkov <asavkov@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
Since common_callchain has been added to the argument array, we need to
reflect it in perl-based scripts, because otherwise the following args
would be shifted and thus incorrect. E.g. rw-by-pid and calculation of
read and written bytes:
Before:
read counts by pid:
pid comm # reads bytes_requested bytes_read
------ -------------------- ----------- ---------- ----------
19301 dd 4 424510450039736 0
After:
read counts by pid:
pid comm # reads bytes_requested bytes_read
------ -------------------- ----------- ---------- ----------
19301 dd 4 9536 4341
Committer testing:
To see before after first do:
# perf script record rw-by-pid
^C
Now you'll have a perf.data file to report on, then do before and after
using:
# perf script report rw-by-pid
Anbd notice the bytes_request/bytes_read, as above.
Signed-off-by: Michael Petlan <mpetlan@redhat.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Benjamin Salon <bsalon@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
LPU-Reference: 20200311132836.12693-1-mpetlan@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Make it easy for people looking in intel-pt.txt to find the new file.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lore.kernel.org/lkml/20200311122034.3697-4-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Add references to Intel PT man page in man pages of associated tools.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lore.kernel.org/lkml/20200311122034.3697-3-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Make the Intel PT documentation into a man page.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lore.kernel.org/lkml/20200311122034.3697-2-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Currently the man page dates reflect the date the man pages were built.
This patch adjusts the date so that the date is when then man page
last had a commit against it. The date is generated using 'git log'.
Committer testing:
$ git log -1 --pretty="format:%cd" --date=short tools/perf/Documentation/perf-top.txt
2020-01-14
Before:
rm -rf /tmp/build/perf
mkdir -p /tmp/build/perf
make -C tools/perf O=/tmp/build/perf/ install
$ date
Wed 11 Mar 2020 10:21:19 AM -03
$ man perf-top | tail -1
perf 03/11/2020 PERF-TOP(1)
$
After:
rm -rf /tmp/build/perf
mkdir -p /tmp/build/perf
make -C tools/perf O=/tmp/build/perf/ install
$ date
$ date
Wed 11 Mar 2020 10:24:06 AM -03
$ man perf-top | tail -1
perf 2020-01-14 PERF-TOP(1)
$
Signed-off-by: Ian Rogers <irogers@google.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Mukesh Ojha <mojha@codeaurora.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lore.kernel.org/lkml/20200311052110.23132-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The variable 'offset' in function cs_etm__sample() is u64 type, it's not
appropriate to check it with 'while (offset > 0)'; this patch changes to
'while (offset)'.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Walker <robert.walker@arm.com>
Cc: Suzuki Poulouse <suzuki.poulose@arm.com>
Cc: coresight ml <coresight@lists.linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lore.kernel.org/lkml/20200219021811.20067-6-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
If an instruction range packet can generate multiple instruction
samples, these samples share the same last branches; it's not necessary
to copy the same last branches repeatedly for these samples within the
same packet.
This patch moves out the last branches copying from function
cs_etm__synth_instruction_sample(), and execute it prior to generating
instruction samples.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Walker <robert.walker@arm.com>
Cc: Suzuki Poulouse <suzuki.poulose@arm.com>
Cc: coresight ml <coresight@lists.linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lore.kernel.org/lkml/20200219021811.20067-5-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
When 'etm->instructions_sample_period' is less than
'tidq->period_instructions', the function cs_etm__sample() cannot handle
this case properly with its logic.
Let's see below flow as an example:
- If we set itrace option '--itrace=i4', then function cs_etm__sample()
has variables with initialized values:
tidq->period_instructions = 0
etm->instructions_sample_period = 4
- When the first packet is coming:
packet->instr_count = 10; the number of instructions executed in this
packet is 10, thus update period_instructions as below:
tidq->period_instructions = 0 + 10 = 10
instrs_over = 10 - 4 = 6
offset = 10 - 6 - 1 = 3
tidq->period_instructions = instrs_over = 6
- When the second packet is coming:
packet->instr_count = 10; in the second pass, assume 10 instructions
in the trace sample again:
tidq->period_instructions = 6 + 10 = 16
instrs_over = 16 - 4 = 12
offset = 10 - 12 - 1 = -3 -> the negative value
tidq->period_instructions = instrs_over = 12
So after handle these two packets, there have below issues:
The first issue is that cs_etm__instr_addr() returns the address within
the current trace sample of the instruction related to offset, so the
offset is supposed to be always unsigned value. But in fact, function
cs_etm__sample() might calculate a negative offset value (in handling
the second packet, the offset is -3) and pass to cs_etm__instr_addr()
with u64 type with a big positive integer.
The second issue is it only synthesizes 2 samples for sample period = 4.
In theory, every packet has 10 instructions so the two packets have
total 20 instructions, 20 instructions should generate 5 samples
(4 x 5 = 20). This is because cs_etm__sample() only calls once
cs_etm__synth_instruction_sample() to generate instruction sample per
range packet.
This patch fixes the logic in function cs_etm__sample(); the basic
idea for handling coming packet is:
- To synthesize the first instruction sample, it combines the left
instructions from the previous packet and the head of the new
packet; then generate continuous samples with sample period;
- At the tail of the new packet, if it has the rest instructions,
these instructions will be left for the sequential sample.
Suggested-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Walker <robert.walker@arm.com>
Cc: Suzuki Poulouse <suzuki.poulose@arm.com>
Cc: coresight ml <coresight@lists.linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lore.kernel.org/lkml/20200219021811.20067-4-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Every time synthesize instruction sample, the last branch recording will
be reset. This is fine if the instruction period is big enough, for
example if use the option '--itrace=i100000', the last branch array is
reset for every sample with 100000 instructions per period; before
generate the next instruction sample, there has the sufficient packets
coming to fill the last branch array.
On the other hand, if set a very small period, the packets will be
significantly reduced between two continuous instruction samples, thus
the last branch array is almost empty for new instruction sample by
frequently resetting.
To allow the last branches to work properly for any instruction periods,
this patch avoids to reset the last branch for every instruction sample
and only reset it when flush the trace data. The last branches will be
reset only for two cases, one is for trace starting, another case is for
discontinuous trace; other cases can keep recording last branches for
continuous instruction samples.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Walker <robert.walker@arm.com>
Cc: Suzuki Poulouse <suzuki.poulose@arm.com>
Cc: coresight ml <coresight@lists.linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lore.kernel.org/lkml/20200219021811.20067-3-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
