| Age | Commit message (Collapse) | Author |
|---|
|
In polling mode, no stop condition is generated after a timeout. This
causes SCL to remain low and thereby block the bus. If this happens
during a transfer it can cause slaves to misinterpret the subsequent
transfer and return wrong values.
To solve this, pass the ETIMEDOUT error up from ocores_process_polling()
instead of setting STATE_ERROR directly. The caller is adjusted to call
ocores_process_timeout() on error both in polling and in IRQ mode, which
will set STATE_ERROR and generate a stop condition.
Fixes: 69c8c0c0efa8 ("i2c: ocores: add polling interface")
Signed-off-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
If AH create request fails, release sgid_attr to avoid GID entry
referrence leak reported while releasing GID table
Fixes: 1a1f460ff151 ("RDMA: Hold the sgid_attr inside the struct ib_ah/qp")
Link: https://lore.kernel.org/r/20230401063424.342204-1-saravanan.vajravel@broadcom.com
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
The usage_data[] array in rfc6803_encrypt_case() is uninitialised, so clear
it as it may cause the tests to fail otherwise.
Fixes: b958cff6b27b ("SUNRPC: Add encryption KUnit tests for the RFC 6803 encryption types")
Link: https://lore.kernel.org/r/380323.1681314997@warthog.procyon.org.uk/
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Chuck Lever <chuck.lever@oracle.com>
cc: Scott Mayhew <smayhew@redhat.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: linux-nfs@vger.kernel.org
cc: linux-crypto@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
|
|
set_rtc_noop(), get_rtc_noop() are after booting, therefore their __init
annotation is wrong.
A crash was observed on an x86 platform where CMOS RTC is unused and
disabled via device tree. set_rtc_noop() was invoked from ntp:
sync_hw_clock(), although CONFIG_RTC_SYSTOHC=n, however sync_cmos_clock()
doesn't honour that.
Workqueue: events_power_efficient sync_hw_clock
RIP: 0010:set_rtc_noop
Call Trace:
update_persistent_clock64
sync_hw_clock
Fix this by dropping the __init annotation from set/get_rtc_noop().
Fixes: c311ed6183f4 ("x86/init: Allow DT configured systems to disable RTC at boot time")
Signed-off-by: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nokia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/59f7ceb1-446b-1d3d-0bc8-1f0ee94b1e18@nokia.com
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v6.3-rc7:
- Fix dual link DSI for TGL+
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/877cugckzu.fsf@intel.com
|
|
Now that we use XPACLRI to strip PACs within the kernel, the
ptrauth_user_pac_mask() and ptrauth_kernel_pac_mask() definitions no
longer need to live in <asm/compiler.h>.
Move them to <asm/pointer_auth.h>, and ensure that this header is
included where they are used.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Amit Daniel Kachhap <amit.kachhap@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Kristina Martsenko <kristina.martsenko@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20230412160134.306148-4-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Currently we strip the PAC from pointers using C code, which requires
generating bitmasks, and conditionally clearing/setting bits depending
on bit 55. We can do better by using XPACLRI directly.
When the logic was originally written to strip PACs from user pointers,
contemporary toolchains used for the kernel had assemblers which were
unaware of the PAC instructions. As stripping the PAC from userspace
pointers required unconditional clearing of a fixed set of bits (which
could be performed with a single instruction), it was simpler to
implement the masking in C than it was to make use of XPACI or XPACLRI.
When support for in-kernel pointer authentication was added, the
stripping logic was extended to cover TTBR1 pointers, requiring several
instructions to handle whether to clear/set bits dependent on bit 55 of
the pointer.
This patch simplifies the stripping of PACs by using XPACLRI directly,
as contemporary toolchains do within __builtin_return_address(). This
saves a number of instructions, especially where
__builtin_return_address() does not implicitly strip the PAC but is
heavily used (e.g. with tracepoints). As the kernel might be compiled
with an assembler without knowledge of XPACLRI, it is assembled using
the 'HINT #7' alias, which results in an identical opcode.
At the same time, I've split ptrauth_strip_insn_pac() into
ptrauth_strip_user_insn_pac() and ptrauth_strip_kernel_insn_pac()
helpers so that we can avoid unnecessary PAC stripping when pointer
authentication is not in use in userspace or kernel respectively.
The underlying xpaclri() macro uses inline assembly which clobbers x30.
The clobber causes the compiler to save/restore the original x30 value
in a frame record (protected with PACIASP and AUTIASP when in-kernel
authentication is enabled), so this does not provide a gadget to alter
the return address. Similarly this does not adversely affect unwinding
due to the presence of the frame record.
The ptrauth_user_pac_mask() and ptrauth_kernel_pac_mask() are exported
from the kernel in ptrace and core dumps, so these are retained. A
subsequent patch will move them out of <asm/compiler.h>.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Amit Daniel Kachhap <amit.kachhap@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Kristina Martsenko <kristina.martsenko@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20230412160134.306148-3-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
In old versions of GCC and Clang, __builtin_return_address() did not
strip the PAC. This was not the behaviour we desired, and so we wrapped
this with code to strip the PAC in commit:
689eae42afd7a916 ("arm64: mask PAC bits of __builtin_return_address")
Since then, both GCC and Clang decided that __builtin_return_address()
*should* strip the PAC, and the existing behaviour was a bug.
GCC was fixed in 11.1.0, with those fixes backported to 10.2.0, 9.4.0,
8.5.0, but not earlier:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=94891
Clang was fixed in 12.0.0, though this was not backported:
https://reviews.llvm.org/D75044
When using a compiler whose __builtin_return_address() strips the PAC,
our wrapper to strip the PAC is redundant. Similarly, when pointer
authentication is not in use within the kernel pointers will not have a
PAC, and so there's no point stripping those pointers.
To avoid this redundant work, this patch updates the
__builtin_return_address() wrapper to only be used when in-kernel
pointer authentication is configured and the compiler's
__builtin_return_address() does not strip the PAC.
This is a cleanup/optimization, and not a fix that requires backporting.
Stripping a PAC should be an idempotent operation, and so redundantly
stripping the PAC is not harmful.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Amit Daniel Kachhap <amit.kachhap@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Kristina Martsenko <kristina.martsenko@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20230412160134.306148-2-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
ctx->vpu_dst_fmt is no more initialized before calling hantro_try_fmt()
so assigne it to vpu_fmt led to crash the kernel.
Like for decoder case use 'fmt' as format for encoder and clean up
the code.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: db6f68b51e5c ("media: verisilicon: Do not set context src/dst formats in reset functions")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
I have observed an issue where the RX direction of the LS1028A ENETC pMAC
seems unresponsive. The minimal procedure to reproduce the issue is:
1. Connect ENETC port 0 with a loopback RJ45 cable to one of the Felix
switch ports (0).
2. Bring the ports up (MAC Merge layer is not enabled on either end).
3. Send a large quantity of unidirectional (express) traffic from Felix
to ENETC. I tried altering frame size and frame count, and it doesn't
appear to be specific to either of them, but rather, to the quantity
of octets received. Lowering the frame count, the minimum quantity of
packets to reproduce relatively consistently seems to be around 37000
frames at 1514 octets (w/o FCS) each.
4. Using ethtool --set-mm, enable the pMAC in the Felix and in the ENETC
ports, in both RX and TX directions, and with verification on both
ends.
5. Wait for verification to complete on both sides.
6. Configure a traffic class as preemptible on both ends.
7. Send some packets again.
The issue is at step 5, where the verification process of ENETC ends
(meaning that Felix responds with an SMD-R and ENETC sees the response),
but the verification process of Felix never ends (it remains VERIFYING).
If step 3 is skipped or if ENETC receives less traffic than
approximately that threshold, the test runs all the way through
(verification succeeds on both ends, preemptible traffic passes fine).
If, between step 4 and 5, the step below is also introduced:
4.1. Disable and re-enable PM0_COMMAND_CONFIG bit RX_EN
then again, the sequence of steps runs all the way through, and
verification succeeds, even if there was the previous RX traffic
injected into ENETC.
Traffic sent *by* the ENETC port prior to enabling the MAC Merge layer
does not seem to influence the verification result, only received
traffic does.
The LS1028A manual does not mention any relationship between
PM0_COMMAND_CONFIG and MMCSR, and the hardware people don't seem to
know for now either.
The bit that is toggled to work around the issue is also toggled
by enetc_mac_enable(), called from phylink's mac_link_down() and
mac_link_up() methods - which is how the workaround was found:
verification would work after a link down/up.
Fixes: c7b9e8086902 ("net: enetc: add support for MAC Merge layer")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230411192645.1896048-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
vexpress-config uses of_platform_* functions which are declared in
of_platform.h. of_platform.h gets implicitly included by of_device.h,
but that is going to be removed soon. Nothing else depends on
of_device.h so it can be dropped.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://lore.kernel.org/r/20230410232727.1562115-1-robh@kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Currently, when traversing ifwdtsn skips with _sctp_walk_ifwdtsn, it only
checks the pos against the end of the chunk. However, the data left for
the last pos may be < sizeof(struct sctp_ifwdtsn_skip), and dereference
it as struct sctp_ifwdtsn_skip may cause coverflow.
This patch fixes it by checking the pos against "the end of the chunk -
sizeof(struct sctp_ifwdtsn_skip)" in sctp_ifwdtsn_skip, similar to
sctp_fwdtsn_skip.
Fixes: 0fc2ea922c8a ("sctp: implement validate_ftsn for sctp_stream_interleave")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/2a71bffcd80b4f2c61fac6d344bb2f11c8fd74f7.1681155810.git.lucien.xin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.3-2023-04-12:
amdgpu:
- SMU13 fixes
- DP MST fix
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230412215637.7881-1-alexander.deucher@amd.com
|
|
Syzbot reported a bug as following:
=====================================================
BUG: KMSAN: uninit-value in qrtr_tx_resume+0x185/0x1f0 net/qrtr/af_qrtr.c:230
qrtr_tx_resume+0x185/0x1f0 net/qrtr/af_qrtr.c:230
qrtr_endpoint_post+0xf85/0x11b0 net/qrtr/af_qrtr.c:519
qrtr_tun_write_iter+0x270/0x400 net/qrtr/tun.c:108
call_write_iter include/linux/fs.h:2189 [inline]
aio_write+0x63a/0x950 fs/aio.c:1600
io_submit_one+0x1d1c/0x3bf0 fs/aio.c:2019
__do_sys_io_submit fs/aio.c:2078 [inline]
__se_sys_io_submit+0x293/0x770 fs/aio.c:2048
__x64_sys_io_submit+0x92/0xd0 fs/aio.c:2048
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Uninit was created at:
slab_post_alloc_hook mm/slab.h:766 [inline]
slab_alloc_node mm/slub.c:3452 [inline]
__kmem_cache_alloc_node+0x71f/0xce0 mm/slub.c:3491
__do_kmalloc_node mm/slab_common.c:967 [inline]
__kmalloc_node_track_caller+0x114/0x3b0 mm/slab_common.c:988
kmalloc_reserve net/core/skbuff.c:492 [inline]
__alloc_skb+0x3af/0x8f0 net/core/skbuff.c:565
__netdev_alloc_skb+0x120/0x7d0 net/core/skbuff.c:630
qrtr_endpoint_post+0xbd/0x11b0 net/qrtr/af_qrtr.c:446
qrtr_tun_write_iter+0x270/0x400 net/qrtr/tun.c:108
call_write_iter include/linux/fs.h:2189 [inline]
aio_write+0x63a/0x950 fs/aio.c:1600
io_submit_one+0x1d1c/0x3bf0 fs/aio.c:2019
__do_sys_io_submit fs/aio.c:2078 [inline]
__se_sys_io_submit+0x293/0x770 fs/aio.c:2048
__x64_sys_io_submit+0x92/0xd0 fs/aio.c:2048
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
It is because that skb->len requires at least sizeof(struct qrtr_ctrl_pkt)
in qrtr_tx_resume(). And skb->len equals to size in qrtr_endpoint_post().
But size is less than sizeof(struct qrtr_ctrl_pkt) when qrtr_cb->type
equals to QRTR_TYPE_RESUME_TX in qrtr_endpoint_post() under the syzbot
scenario. This triggers the uninit variable access bug.
Add size check when qrtr_cb->type equals to QRTR_TYPE_RESUME_TX in
qrtr_endpoint_post() to fix the bug.
Fixes: 5fdeb0d372ab ("net: qrtr: Implement outgoing flow control")
Reported-by: syzbot+4436c9630a45820fda76@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=c14607f0963d27d5a3d5f4c8639b500909e43540
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230410012352.3997823-1-william.xuanziyang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add the device tree node for the UART DMA (UDMA) controller.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Link: https://lore.kernel.org/r/20230320081133.23655-6-chiawei_wang@aspeedtech.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Add mctp node on I2C bus
Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@Wiwynn.com>
Link: https://lore.kernel.org/r/20230329083235.24123-3-Delphine_CC_Chiu@Wiwynn.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Add GPIO names for SOC lines.
Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
Link: https://lore.kernel.org/r/20230329083235.24123-2-Delphine_CC_Chiu@Wiwynn.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Bonnell system supports new ACBEL FSG032 power supply on
I2C addresses 5A and 5B. Update the device tree with new
power supply information and device addresses.
Signed-off-by: Lakshmi Yadlapati <lakshmiy@us.ibm.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20230412052305.1369521-6-lakshmiy@us.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
These Lenovo laptops use Realtek HDA codec combined with
2xCS35L41 Amplifiers using I2C with External Boost.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230412160531.182007-1-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Was introduced as workaround. not needed anymore
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Jack Gui <Jack.Gui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch adds double include protection for doorbell.h
Cc: Christian Koenig <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian Koenig <christian.koenig@amd.com>
Signed-off-by: Shashank Sharma <shashank.sharma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Rename doorbell.num_doorbells to doorbell.num_kernel_doorbells to
make it more readable.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian Koenig <christian.koenig@amd.com>
Acked-by: Christian Koenig <christian.koenig@amd.com>
Signed-off-by: Shashank Sharma <shashank.sharma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Due to raven/raven2 maybe enable sclk slow down,
they cannot get clock count by the RLC at the auto level of dpm performance.
So switch to golden tsc register.
Suggested-by: shanshengwang <shansheng.wang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Jesse Zhang <jesse.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Update the driver implementations to fit those data exposed
by PMFW.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add gfx v11_0_3 fed irq handling for sriov.
Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Rework retry fault removal from the software filter by
storing an expired timestamp for a fault that is being removed.
When a new fault comes, and it matches an entry in the sw filter,
it will be added as a new fault only when its timestamp is greater
than the timestamp expiry of the fault in the sw filter.
This helps in avoiding stale faults being added back into the
filter and preventing legitimate faults from being handled.
Suggested-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch enables the IH retry CAM on GFX9 series cards. This
retry filter is used to prevent sending lots of retry interrupts
in a short span of time and overflowing the IH ring buffer. This
will also help reduce CPU interrupt workload.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
clang with W=1 reports
drivers/gpu/drm/amd/amdgpu/../pm/swsmu/amdgpu_smu.c:1700:6: error: variable
'num_of_active_display' set but not used [-Werror,-Wunused-but-set-variable]
int num_of_active_display = 0;
^
This variable is not used so remove it.
Fixes: 75145aab7a0d ("drm/amdgpu/swsmu: clean up a bunch of stale interfaces")
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
All chips that support RAS also support IP discovery, so
use the IP versions rather than a mix of IP versions and
asic types. Checking the validity of the atom_ctx pointer
is not required as the vbios is already fetched at this
point.
v2: add comments to id asic types based on feedback from Luben
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Luben Tuikov <luben.tuikov@amd.com>
|
|
The commits referenced below allows userspace to use the NLM_F_ECHO flag
for RTM_NEW/DELLINK operations to receive unicast notifications for the
affected link. Prior to these changes, applications may have relied on
multicast notifications to learn the same information without specifying
the NLM_F_ECHO flag.
For such applications, the mentioned commits changed the behavior for
requests not using NLM_F_ECHO. Multicast notifications are still received,
but now use the portid of the requester and the sequence number of the
request instead of zero values used previously. For the application, this
message may be unexpected and likely handled as a response to the
NLM_F_ACKed request, especially if it uses the same socket to handle
requests and notifications.
To fix existing applications relying on the old notification behavior,
set the portid and sequence number in the notification only if the
request included the NLM_F_ECHO flag. This restores the old behavior
for applications not using it, but allows unicasted notifications for
others.
Fixes: f3a63cce1b4f ("rtnetlink: Honour NLM_F_ECHO flag in rtnl_delete_link")
Fixes: d88e136cab37 ("rtnetlink: Honour NLM_F_ECHO flag in rtnl_newlink_create")
Signed-off-by: Martin Willi <martin@strongswan.org>
Acked-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20230411074319.24133-1-martin@strongswan.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- kernel panic fix for intel-ish-hid driver (Tanu Malhotra)
- buffer overflow fix in hid-sensor-custom driver (Todd Brandt)
- two device specific quirks (Alessandro Manca, Philippe Troin)
* tag 'for-linus-2023041201' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: intel-ish-hid: Fix kernel panic during warm reset
HID: hid-sensor-custom: Fix buffer overrun in device name
HID: topre: Add support for 87 keys Realforce R2
HID: add HP 13t-aw100 & 14t-ea100 digitizer battery quirks
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine fixes from Vinod Koul:
"A couple of fixes in apple driver, core and kernedoc fix for dmaengine
subsystem:
- apple admac driver fixes for current_tx, src_addr_widths and
global' interrupt flags handling
- xdma kerneldoc fix
- core fix for use of devm_add_action_or_reset"
* tag 'dmaengine-fix-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: apple-admac: Fix 'current_tx' not getting freed
dmaengine: apple-admac: Set src_addr_widths capability
dmaengine: apple-admac: Handle 'global' interrupt flags
dmaengine: xilinx: xdma: Fix some kernel-doc comments
dmaengine: Actually use devm_add_action_or_reset()
|
|
The Makefile rule responsible for building flask.h and
av_permissions.h only lists flask.h as a target which means that
av_permissions.h is only generated when flask.h needs to be
generated. This patch fixes this by adding av_permissions.h as a
target to the rule.
Fixes: 8753f6bec352 ("selinux: generate flask headers during kernel build")
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Update the driver implementations to fit those data exposed
by PMFW.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
|
|
Correct the max shader clock reporting on SMU
13.0.7.
Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
|
|
Correct the pstate standard/peak profiling mode clock
settings for SMU13.0.7.
Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
|
|
[Why & How]
drm_dp_remove_payload() interface was changed. Correct amdgpu dm code
to pass the right parameter to the drm helper function.
Reviewed-by: Jerry Zuo <Jerry.Zuo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It is found that attaching a task to the top_cpuset does not currently
ignore CPUs allocated to subpartitions in cpuset_attach_task(). So the
code is changed to fix that.
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
In the case of CLONE_INTO_CGROUP, not all cpusets are ready to accept
new tasks. It is too late to check that in cpuset_fork(). So we need
to add the cpuset_can_fork() and cpuset_cancel_fork() methods to
pre-check it before we can allow attachment to a different cpuset.
We also need to set the attach_in_progress flag to alert other code
that a new task is going to be added to the cpuset.
Fixes: ef2c41cf38a7 ("clone3: allow spawning processes into cgroups")
Suggested-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Cc: stable@vger.kernel.org # v5.7+
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
By default, the clone(2) syscall spawn a child process into the same
cgroup as its parent. With the use of the CLONE_INTO_CGROUP flag
introduced by commit ef2c41cf38a7 ("clone3: allow spawning processes
into cgroups"), the child will be spawned into a different cgroup which
is somewhat similar to writing the child's tid into "cgroup.threads".
The current cpuset_fork() method does not properly handle the
CLONE_INTO_CGROUP case where the cpuset of the child may be different
from that of its parent. Update the cpuset_fork() method to treat the
CLONE_INTO_CGROUP case similar to cpuset_attach().
Since the newly cloned task has not been running yet, its actual
memory usage isn't known. So it is not necessary to make change to mm
in cpuset_fork().
Fixes: ef2c41cf38a7 ("clone3: allow spawning processes into cgroups")
Reported-by: Giuseppe Scrivano <gscrivan@redhat.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Cc: stable@vger.kernel.org # v5.7+
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
After a successful cpuset_can_attach() call which increments the
attach_in_progress flag, either cpuset_cancel_attach() or cpuset_attach()
will be called later. In cpuset_attach(), tasks in cpuset_attach_wq,
if present, will be woken up at the end. That is not the case in
cpuset_cancel_attach(). So missed wakeup is possible if the attach
operation is somehow cancelled. Fix that by doing the wakeup in
cpuset_cancel_attach() as well.
Fixes: e44193d39e8d ("cpuset: let hotplug propagation work wait for task attaching")
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Michal Koutný <mkoutny@suse.com>
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Make the flask.h target depend on the genheaders binary instead of
classmap.h to ensure that it is rebuilt if any of the dependencies of
genheaders are changed.
Notably this fixes flask.h not being rebuilt when
initial_sid_to_string.h is modified.
Fixes: 8753f6bec352 ("selinux: generate flask headers during kernel build")
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Acked-by: Stephen Smalley <stephen.smalley.work@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
syzbot is reporting circular locking dependency between cpu_hotplug_lock
and freezer_mutex, for commit f5d39b020809 ("freezer,sched: Rewrite core
freezer logic") replaced atomic_inc() in freezer_apply_state() with
static_branch_inc() which holds cpu_hotplug_lock.
cpu_hotplug_lock => cgroup_threadgroup_rwsem => freezer_mutex
cgroup_file_write() {
cgroup_procs_write() {
__cgroup_procs_write() {
cgroup_procs_write_start() {
cgroup_attach_lock() {
cpus_read_lock() {
percpu_down_read(&cpu_hotplug_lock);
}
percpu_down_write(&cgroup_threadgroup_rwsem);
}
}
cgroup_attach_task() {
cgroup_migrate() {
cgroup_migrate_execute() {
freezer_attach() {
mutex_lock(&freezer_mutex);
(...snipped...)
}
}
}
}
(...snipped...)
}
}
}
freezer_mutex => cpu_hotplug_lock
cgroup_file_write() {
freezer_write() {
freezer_change_state() {
mutex_lock(&freezer_mutex);
freezer_apply_state() {
static_branch_inc(&freezer_active) {
static_key_slow_inc() {
cpus_read_lock();
static_key_slow_inc_cpuslocked();
cpus_read_unlock();
}
}
}
mutex_unlock(&freezer_mutex);
}
}
}
Swap locking order by moving cpus_read_lock() in freezer_apply_state()
to before mutex_lock(&freezer_mutex) in freezer_change_state().
Reported-by: syzbot <syzbot+c39682e86c9d84152f93@syzkaller.appspotmail.com>
Link: https://syzkaller.appspot.com/bug?extid=c39682e86c9d84152f93
Suggested-by: Hillf Danton <hdanton@sina.com>
Fixes: f5d39b020809 ("freezer,sched: Rewrite core freezer logic")
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
After commit 6376ce56feb6 ("iov_iter: import single vector iovecs as
ITER_UBUF"), GCC does an inter-procedural compiler optimization which
moves the user_access_begin() out of copy_compat_iovec_from_user() and
into its callers:
lib/iov_iter.o: warning: objtool: .altinstr_replacement+0x0: redundant UACCESS disable
lib/iov_iter.o: warning: objtool: iovec_from_user.part.0+0xc7: call to copy_compat_iovec_from_user.part.0() with UACCESS enabled
lib/iov_iter.o: warning: objtool: __import_iovec+0x21d: call to copy_compat_iovec_from_user.part.0() with UACCESS enabled
Enforce the "no UACCESS enable across function boundaries" rule by
disabling cloning for copy_compat_iovec_from_user().
Fixes: 6376ce56feb6 ("iov_iter: import single vector iovecs as ITER_UBUF")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
https://lkml.kernel.org/lkml/20230327120017.6bb826d7@canb.auug.org.au
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Tested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Merge series from Benjamin Bara <bbara93@gmail.com>:
Follow-up for my initial patch regarding the disabling of unused
voltage monitors. We use the PWR_OK functionality, which asserts GP_FB2
if every monitored voltage is in range. This patch should provide the
possibility to deactivate a voltage monitor from the DT if the regulator
might be disabled during run time. For this purpose, the regulator
notification support is used:
https://lore.kernel.org/all/cover.1622628333.git.matti.vaittinen@fi.rohmeurope.com/
|
|
Fix netfs_extract_iter_to_sg() for ITER_UBUF and ITER_IOVEC to set the
size of the page to the part of the page extracted, not the remaining
amount of data in the extracted page array at that point.
This doesn't yet affect anything as cifs, the only current user, only
passes in non-user-backed iterators.
Fixes: 018584697533 ("netfs: Add a function to extract an iterator into a scatterlist")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Cc: Steve French <sfrench@samba.org>
Cc: Shyam Prasad N <nspmangalore@gmail.com>
Cc: Rohith Surabattula <rohiths.msft@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
arch_dynirq_lower_bound() is invoked by the core interrupt code to
retrieve the lowest possible Linux interrupt number for dynamically
allocated interrupts like MSI.
The x86 implementation uses this to exclude the IO/APIC GSI space.
This works correctly as long as there is an IO/APIC registered, but
returns 0 if not. This has been observed in VMs where the BIOS does
not advertise an IO/APIC.
0 is an invalid interrupt number except for the legacy timer interrupt
on x86. The return value is unchecked in the core code, so it ends up
to allocate interrupt number 0 which is subsequently considered to be
invalid by the caller, e.g. the MSI allocation code.
The function has already a check for 0 in the case that an IO/APIC is
registered, as ioapic_dynirq_base is 0 in case of device tree setups.
Consolidate this and zero check for both ioapic_dynirq_base and gsi_top,
which is used in the case that no IO/APIC is registered.
Fixes: 3e5bedc2c258 ("x86/apic: Fix arch_dynirq_lower_bound() bug for DT enabled machines")
Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/1679988604-20308-1-git-send-email-ssengar@linux.microsoft.com
|
|
When local group is fully busy but its average load is above system load,
computing the imbalance will overflow and local group is not the best
target for pulling this load.
Fixes: 0b0695f2b34a ("sched/fair: Rework load_balance()")
Reported-by: Tingjia Cao <tjcao980311@gmail.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Tingjia Cao <tjcao980311@gmail.com>
Link: https://lore.kernel.org/lkml/CABcWv9_DAhVBOq2=W=2ypKE9dKM5s2DvoV8-U0+GDwwuKZ89jQ@mail.gmail.com/T/
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.4-rc1:
Cross-subsystem Changes:
- Convert MIPI DSIM bridge dt to yaml.
Core Changes:
- Fix UAF race in drm scheduler.
Driver Changes:
- Add primary plane positioning support to VKMS.
- Convert omapdrm fbdev emulation to in-kernel client.
- Assorted small fixes to vkms, vc4, nouveau, vmwgfx.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b7c37d4e-8f16-85dc-0f5f-3bd98f961395@linux.intel.com
|
|
This smartphone features a Bosch BMM050 Magnetometer on I2C3: enable
it with the BMM150 binding, as that driver supports BMM050 as well.
For this sensor, there is no interrupt pin;
readings were validated in sysfs.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230412112739.160376-28-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
