| Age | Commit message (Collapse) | Author |
|---|
|
This is in preparation for a fix, but serves as a cleanup as well moving
the cached vs regular alloc logic out of blk_mq_submit_bio().
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Requests that were stored in the cache deliberately didn't hold an enter
reference to the queue, instead we grabbed one every time we pulled a
request out of there. That made for awkward logic on freeing the remainder
of the cached list, if needed, where we had to artificially raise the
queue usage count before each free.
Grab references up front for cached plug requests. That's safer, and also
more efficient.
Fixes: 47c122e35d7e ("block: pre-allocate requests if plug is started and is a batch")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
It is possible that some performance excursions happened before OS boot
or enable HWP interrupts. So clear MSR_HWP_STATUS bits when we enable
HWP interrupt. In this way a next excursion will results in a HWP
interrupt.
The status bits of MSR_HWP_STATUS must be cleared (0) by software so
that a new status condition change will cause the hardware to set the
bit again and issue the notification.
Fixes: 57577c996d73 ("cpufreq: intel_pstate: Process HWP Guaranteed change notification")
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It is possible that on some platforms HWP interrupts are disabled. In
that case accessing MSR 0x773 will result in warning.
So check X86_FEATURE_HWP_NOTIFY feature to access MSR 0x773. The other
places in code where this MSR is accessed, already checks this feature
except during disable path called during cpufreq offline and suspend
callbacks.
Fixes: 57577c996d73 ("cpufreq: intel_pstate: Process HWP Guaranteed change notification")
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit a365ab6b9dfb ("cpufreq: intel_pstate: Implement the
->adjust_perf() callback") caused intel_pstate to use nonzero HWP
desired values in certain usage scenarios, but it did not prevent
them from being leaked into the confugirations in which HWP desired
is expected to be 0.
The failing scenarios are switching the driver from the passive
mode to the active mode and starting a new kernel via kexec() while
intel_pstate is running in the passive mode.
To address this issue, ensure that HWP desired will be cleared on
offline and suspend/shutdown.
Fixes: a365ab6b9dfb ("cpufreq: intel_pstate: Implement the ->adjust_perf() callback")
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Tested-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In the cpuidle-psci case, runtime PM in combination with the generic PM
domain (genpd), may be used when entering/exiting a shared idlestate. More
precisely, genpd relies on runtime PM to be enabled for the attached device
(in this case it belongs to a CPU), to properly manage the reference
counting of its PM domain.
This works fine most of the time, but during system suspend in
dpm_suspend_late(), the PM core disables runtime PM for all devices. Beyond
this point, calls to pm_runtime_get_sync() to runtime resume a device may
fail and therefore it could also mess up the reference counting in genpd.
To fix this problem, let's call wake_up_all_idle_cpus() in
dpm_suspend_late(), prior to disabling runtime PM. In this way a device
that belongs to a CPU, becomes runtime resumed through cpuidle-psci and
stays like that, because the runtime PM usage count has been bumped in
device_prepare().
Diagnosed-by: Maulik Shah <mkshah@codeaurora.org>
Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Host crashes when pci_enable_atomic_ops_to_root() is called for VFs with
virtual buses. The virtual buses added to SR-IOV have bus->self set to NULL
and host crashes due to this.
PID: 4481 TASK: ffff89c6941b0000 CPU: 53 COMMAND: "bash"
...
#3 [ffff9a9481713808] oops_end at ffffffffb9025cd6
#4 [ffff9a9481713828] page_fault_oops at ffffffffb906e417
#5 [ffff9a9481713888] exc_page_fault at ffffffffb9a0ad14
#6 [ffff9a94817138b0] asm_exc_page_fault at ffffffffb9c00ace
[exception RIP: pcie_capability_read_dword+28]
RIP: ffffffffb952fd5c RSP: ffff9a9481713960 RFLAGS: 00010246
RAX: 0000000000000001 RBX: ffff89c6b1096000 RCX: 0000000000000000
RDX: ffff9a9481713990 RSI: 0000000000000024 RDI: 0000000000000000
RBP: 0000000000000080 R8: 0000000000000008 R9: ffff89c64341a2f8
R10: 0000000000000002 R11: 0000000000000000 R12: ffff89c648bab000
R13: 0000000000000000 R14: 0000000000000000 R15: ffff89c648bab0c8
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffff9a9481713988] pci_enable_atomic_ops_to_root at ffffffffb95359a6
#8 [ffff9a94817139c0] bnxt_qplib_determine_atomics at ffffffffc08c1a33 [bnxt_re]
#9 [ffff9a94817139d0] bnxt_re_dev_init at ffffffffc08ba2d1 [bnxt_re]
Per PCIe r5.0, sec 9.3.5.10, the AtomicOp Requester Enable bit in Device
Control 2 is reserved for VFs. The PF value applies to all associated VFs.
Return -EINVAL if pci_enable_atomic_ops_to_root() is called for a VF.
Link: https://lore.kernel.org/r/1631354585-16597-1-git-send-email-selvin.xavier@broadcom.com
Fixes: 35f5ace5dea4 ("RDMA/bnxt_re: Enable global atomic ops if platform supports")
Fixes: 430a23689dea ("PCI: Add pci_enable_atomic_ops_to_root()")
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull more parisc architecture fixes and updates from Helge Deller:
"One build error fix and two optimizations:
- Fix build error by moving the CPU field back into thread_info
struct (Ard Biesheuvel)
- Do not enable IRQs unconditionally at start of interrupt handler if
they were disabled before (Sven Schnelle)
- Keep interrupts enabled during cmpxchg and futex operations (Dave
Anglin)"
* tag 'for-5.16/parisc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: move CPU field back into thread_info
parisc: Don't disable interrupts in cmpxchg and futex operations
parisc: don't enable irqs unconditionally in handle_interruption()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Intel IOMMU Updates fro Lu Baolu:
- Dump DMAR translation structure when DMA fault occurs
- An optimization in the page table manipulation code
- Use second level for GPA->HPA translation
- Various cleanups
- Arm SMMU Updates from Will
- Minor optimisations to SMMUv3 command creation and submission
- Numerous new compatible string for Qualcomm SMMUv2 implementations
- Fixes for the SWIOTLB based implemenation of dma-iommu code for
untrusted devices
- Add support for r8a779a0 to the Renesas IOMMU driver and DT matching
code for r8a77980
- A couple of cleanups and fixes for the Apple DART IOMMU driver
- Make use of generic report_iommu_fault() interface in the AMD IOMMU
driver
- Various smaller fixes and cleanups
* tag 'iommu-updates-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (35 commits)
iommu/dma: Fix incorrect error return on iommu deferred attach
iommu/dart: Initialize DART_STREAMS_ENABLE
iommu/dma: Use kvcalloc() instead of kvzalloc()
iommu/tegra-smmu: Use devm_bitmap_zalloc when applicable
iommu/dart: Use kmemdup instead of kzalloc and memcpy
iommu/vt-d: Avoid duplicate removing in __domain_mapping()
iommu/vt-d: Convert the return type of first_pte_in_page to bool
iommu/vt-d: Clean up unused PASID updating functions
iommu/vt-d: Delete dev_has_feat callback
iommu/vt-d: Use second level for GPA->HPA translation
iommu/vt-d: Check FL and SL capability sanity in scalable mode
iommu/vt-d: Remove duplicate identity domain flag
iommu/vt-d: Dump DMAR translation structure when DMA fault occurs
iommu/vt-d: Do not falsely log intel_iommu is unsupported kernel option
iommu/arm-smmu-qcom: Request direct mapping for modem device
iommu: arm-smmu-qcom: Add compatible for QCM2290
dt-bindings: arm-smmu: Add compatible for QCM2290 SoC
iommu/arm-smmu-qcom: Add SM6350 SMMU compatible
dt-bindings: arm-smmu: Add compatible for SM6350 SoC
iommu/arm-smmu-v3: Properly handle the return value of arm_smmu_cmdq_build_cmd()
...
|
|
alloc_xenballooned_pages() and free_xenballooned_pages() are used as
direct replacements of xen_alloc_unpopulated_pages() and
xen_free_unpopulated_pages() in case CONFIG_XEN_UNPOPULATED_ALLOC isn't
defined.
Guard both functions with !CONFIG_XEN_UNPOPULATED_ALLOC and rename them
to the xen_*() variants they are replacing. This allows to remove some
ifdeffery from the xen.h header file. Adapt the prototype of the
functions to match.
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20211102092234.17852-1-jgross@suse.com
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
When running as PVH or HVM guest with actual memory < max memory the
hypervisor is using "populate on demand" in order to allow the guest
to balloon down from its maximum memory size. For this to work
correctly the guest must not touch more memory pages than its target
memory size as otherwise the PoD cache will be exhausted and the guest
is crashed as a result of that.
In extreme cases ballooning down might not be finished today before
the init process is started, which can consume lots of memory.
In order to avoid random boot crashes in such cases, add a late init
call to wait for ballooning down having finished for PVH/HVM guests.
Warn on console if initial ballooning fails, panic() after stalling
for more than 3 minutes per default. Add a module parameter for
changing this timeout.
[boris: replaced pr_info() with pr_notice()]
Cc: <stable@vger.kernel.org>
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20211102091944.17487-1-jgross@suse.com
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
Not really needed as both loff_t and sector_t are always 64-bits wide,
but this documents the different types a bit better.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20211104172037.531803-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.16-rc1.
Nothing major in here at all, just lots of tiny serial and tty driver
updates for various reported things, and some good cleanups. These
include:
- more good tty api cleanups from Jiri
- stm32 serial driver updates
- softlockup fix for non-preempt systems under high serial load
- rpmsg serial driver update
- 8250 drivers updates and fixes
- n_gsm line discipline fixes and updates as people are finally
starting to use it.
All of these have been in linux-next for a while now with no reported
issues"
* tag 'tty-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (86 commits)
tty: Fix extra "not" in TTY_DRIVER_REAL_RAW description
serial: cpm_uart: Protect udbg definitions by CONFIG_SERIAL_CPM_CONSOLE
tty: rpmsg: Define tty name via constant string literal
tty: rpmsg: Add pr_fmt() to prefix messages
tty: rpmsg: Use dev_err_probe() in ->probe()
tty: rpmsg: Unify variable used to keep an error code
tty: rpmsg: Assign returned id to a local variable
serial: stm32: push DMA RX data before suspending
serial: stm32: terminate / restart DMA transfer at suspend / resume
serial: stm32: rework RX dma initialization and release
serial: 8250_pci: Remove empty stub pci_quatech_exit()
serial: 8250_pci: Replace custom pci_match_id() implementation
serial: xilinx_uartps: Fix race condition causing stuck TX
serial: sunzilog: Mark sunzilog_putchar() __maybe_unused
Revert "tty: hvc: pass DMA capable memory to put_chars()"
Revert "virtio-console: remove unnecessary kmemdup()"
serial: 8250_pci: Replace dev_*() by pci_*() macros
serial: 8250_pci: Get rid of redundant 'else' keyword
serial: 8250_pci: Refactor the loop in pci_ite887x_init()
tty: add rpmsg driver
...
|
|
Declaring the struct packed here is mostly harmless,
but gives a bad example for people to copy.
As the struct is packed and aligned manually,
let's just drop the attribute.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
This patch adds IRQ support for the virtio GPIO driver. Note that this
uses the irq_bus_lock/unlock() callbacks, since those operations over
virtio may sleep.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the big set of driver core changes for 5.16-rc1.
All of these have been in linux-next for a while now with no reported
problems.
Included in here are:
- big update and cleanup of the sysfs abi documentation files and
scripts from Mauro. We are almost at the place where we can
properly check that the running kernel's sysfs abi is documented
fully.
- firmware loader updates
- dyndbg updates
- kernfs cleanups and fixes from Christoph
- device property updates
- component fix
- other minor driver core cleanups and fixes"
* tag 'driver-core-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (122 commits)
device property: Drop redundant NULL checks
x86/build: Tuck away built-in firmware under FW_LOADER
vmlinux.lds.h: wrap built-in firmware support under FW_LOADER
firmware_loader: move struct builtin_fw to the only place used
x86/microcode: Use the firmware_loader built-in API
firmware_loader: remove old DECLARE_BUILTIN_FIRMWARE()
firmware_loader: formalize built-in firmware API
component: do not leave master devres group open after bind
dyndbg: refine verbosity 1-4 summary-detail
gpiolib: acpi: Replace custom code with device_match_acpi_handle()
i2c: acpi: Replace custom function with device_match_acpi_handle()
driver core: Provide device_match_acpi_handle() helper
dyndbg: fix spurious vNpr_info change
dyndbg: no vpr-info on empty queries
dyndbg: vpr-info on remove-module complete, not starting
device property: Add missed header in fwnode.h
Documentation: dyndbg: Improve cli param examples
dyndbg: Remove support for ddebug_query param
dyndbg: make dyndbg a known cli param
dyndbg: show module in vpr-info in dd-exec-queries
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char and misc and other tiny driver subsystem
updates for 5.16-rc1.
Loads of things in here, all of which have been in linux-next for a
while with no reported problems (except for one called out below.)
Included are:
- habanana labs driver updates, including dma_buf usage, reviewed and
acked by the dma_buf maintainers
- iio driver update (going through this tree not staging as they
really do not belong going through that tree anymore)
- counter driver updates
- hwmon driver updates that the counter drivers needed, acked by the
hwmon maintainer
- xillybus driver updates
- binder driver updates
- extcon driver updates
- dma_buf module namespaces added (will cause a build error in arm64
for allmodconfig, but that change is on its way through the drm
tree)
- lkdtm driver updates
- pvpanic driver updates
- phy driver updates
- virt acrn and nitr_enclaves driver updates
- smaller char and misc driver updates"
* tag 'char-misc-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (386 commits)
comedi: dt9812: fix DMA buffers on stack
comedi: ni_usb6501: fix NULL-deref in command paths
arm64: errata: Enable TRBE workaround for write to out-of-range address
arm64: errata: Enable workaround for TRBE overwrite in FILL mode
coresight: trbe: Work around write to out of range
coresight: trbe: Make sure we have enough space
coresight: trbe: Add a helper to determine the minimum buffer size
coresight: trbe: Workaround TRBE errata overwrite in FILL mode
coresight: trbe: Add infrastructure for Errata handling
coresight: trbe: Allow driver to choose a different alignment
coresight: trbe: Decouple buffer base from the hardware base
coresight: trbe: Add a helper to pad a given buffer area
coresight: trbe: Add a helper to calculate the trace generated
coresight: trbe: Defer the probe on offline CPUs
coresight: trbe: Fix incorrect access of the sink specific data
coresight: etm4x: Add ETM PID for Kryo-5XX
coresight: trbe: Prohibit trace before disabling TRBE
coresight: trbe: End the AUX handle on truncation
coresight: trbe: Do not truncate buffer on IRQ
coresight: trbe: Fix handling of spurious interrupts
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the big set of staging driver updates and cleanups for
5.16-rc1.
Overall we ended up removing a lot of code this time, a bit over
20,000 lines are now gone thanks to a lot of cleanup work by many
developers.
Nothing huge in here functionality wise, just loads of cleanups:
- r8188eu driver major cleanups and removal of unused and dead code
- wlan-ng minor cleanups
- fbtft driver cleanups
- most driver cleanups
- rtl8* drivers cleanups
- rts5208 driver cleanups
- vt6655 driver cleanups
- vc04_services drivers cleanups
- wfx cleanups on the way to almost getting this merged out of
staging (it's close!)
- tiny mips changes needed for the mt7621 drivers, they have been
acked by the respective subsystem maintainers to go through this
tree.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (622 commits)
staging: r8188eu: hal: remove goto statement and local variable
staging: rtl8723bs: hal remove the assignment to itself
staging: rtl8723bs: fix unmet dependency on CRYPTO for CRYPTO_LIB_ARC4
staging: vchiq_core: get rid of typedef
staging: fieldbus: anybus: reframe comment to avoid warning
staging: r8188eu: fix missing unlock in rtw_resume()
staging: r8188eu: core: remove the goto from rtw_IOL_accquire_xmit_frame
staging: r8188eu: core: remove goto statement
staging: vt6655: Rename `dwAL7230InitTable` array
staging: vt6655: Rename `dwAL2230PowerTable` array
staging: vt6655: Rename `dwAL7230InitTableAMode` array
staging: vt6655: Rename `dwAL7230ChannelTable2` array
staging: vt6655: Rename `dwAL7230ChannelTable1` array
staging: vt6655: Rename `dwAL7230ChannelTable0` array
staging: vt6655: Rename `dwAL2230ChannelTable1` array
staging: vt6655: Rename `dwAL2230ChannelTable0` array
staging: r8712u: fix control-message timeout
staging: rtl8192u: fix control-message timeouts
staging: mt7621-dts: add missing SPDX license to files
staging: vchiq_core: fix quoted strings split across lines
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the big set of USB and Thunderbolt driver updates for
5.16-rc1.
Nothing major in here, just lots of little cleanups and additions for
new hardware, all of which have been in linux-next for a while with no
reported problems.
Included in here are:
- tiny Thunderbolt driver updates
- USB typec driver updates
- USB serial driver updates
- USB gadget driver updates
- dwc2 and dwc3 controller driver updates
- tiny USB host driver updates
- minor USB driver fixes and updates
- USB dts updates for various platforms"
* tag 'usb-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (123 commits)
usb: gadget: Mark USB_FSL_QE broken on 64-bit
usb: gadget: f_mass_storage: Disable eps during disconnect
usb: gadget: udc: core: Revise comments for USB ep enable/disable
USB: serial: keyspan: fix memleak on probe errors
USB: serial: cp210x: use usb_control_msg_recv() and usb_control_msg_send()
USB: serial: ch314: use usb_control_msg_recv()
USB: iowarrior: fix control-message timeouts
Documentation: USB: fix example bulk-message timeout
usb: dwc2: stm32mp15: set otg_rev
usb: dwc2: add otg_rev and otg_caps information for gadget driver
dt-bindings: usb: dwc2: adopt otg properties defined in usb-drd.yaml
dt-bindings: usb: dwc2: Add reference to usb-drd.yaml
usb: gadget: uvc: implement dwPresentationTime and scrSourceClock
usb: gadget: uvc: use on returned header len in video_encode_isoc_sg
usb:gadget: f_uac1: fixed sync playback
Docs: usb: remove :c:func: for usb_register and usb_deregister
Docs: usb: update struct usb_driver
usb: gadget: configfs: change config attributes file operation
usb: gadget: configfs: add cfg_to_gadget_info() helper
usb: dwc3: Align DWC3_EP_* flag macros
...
|
|
We already include <linux/device.h> and <linux/msi.h>, which
include <asm/device.h> and <asm/msi.h>.
Drop the redundant includes of <asm/device.h> and <asm/msi.h>.
[bhelgaas: squash in fix from Wan Jiabing <wanjiabing@vivo.com>:
https://lore.kernel.org/r/20211104063720.29375-1-wanjiabing@vivo.com]
Link: https://lore.kernel.org/r/20211013003145.1107148-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Derrick <jonathan.derrick@linux.dev>
|
|
This regression can be reproduced with ntfs-3g and overlayfs:
mkdir lower upper work overlay
dd if=/dev/zero of=ntfs.raw bs=1M count=2
mkntfs -F ntfs.raw
mount ntfs.raw lower
touch lower/file.txt
mount -t overlay -o lowerdir=lower,upperdir=upper,workdir=work - overlay
mv overlay/file.txt overlay/file2.txt
mv fails and (misleadingly) prints
mv: cannot move 'overlay/file.txt' to a subdirectory of itself, 'overlay/file2.txt'
The reason is that ovl_copy_fileattr() is triggered due to S_NOATIME being
set on all inodes (by fuse) regardless of fileattr.
ovl_copy_fileattr() tries to retrieve file attributes from lower file, but
that fails because filesystem does not support this ioctl (this should fail
with ENOTTY, but ntfs-3g return EINVAL instead). This failure is
propagated to origial operation (in this case rename) that triggered the
copy-up.
The fix is to ignore ENOTTY and EINVAL errors from fileattr_get() in copy
up. This also requires turning the internal ENOIOCTLCMD into ENOTTY.
As a further measure to prevent unnecessary failures, only try the
fileattr_get/set on upper if there are any flags to copy up.
Side note: a number of filesystems set S_NOATIME (and sometimes other inode
flags) irrespective of fileattr flags. This causes unnecessary calls
during copy up, which might lead to a performance issue, especially if
latency is high. To fix this, the kernel would need to differentiate
between the two cases. E.g. introduce SB_NOATIME_UPDATE, a per-sb variant
of S_NOATIME. SB_NOATIME doesn't work, because that's interpreted as
"filesystem doesn't store an atime attribute"
Reported-and-tested-by: Kevin Locke <kevin@kevinlocke.name>
Fixes: 72db82115d2b ("ovl: copy up sync/noatime fileattr flags")
Cc: <stable@vger.kernel.org> # v5.15
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
The parameters to two functions and the location of a variable have
changed in more recent LLVM/clang releases.
Remove the unneecessary -fmessage-length and -ferror-limit flags, the
former causes failures like:
58: builtin clang support :
58.1: builtin clang compile C source to IR :
--- start ---
test child forked, pid 279307
error: unknown argument: '-fmessage-length'
1 error generated.
test child finished with -1
Tested with LLVM 6, 8, 9, 10 and 11.
Reviewed-by: Fangrui Song <maskray@google.com>
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sedat Dilek <sedat.dilek@gmail.com>,
Cc: llvm@lists.linux.dev
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
LLVM 9 (current release is LLVM 13) moved the minimum C++ version to
GNU++14. Bump the version numbers in the feature test and perf build.
Reviewed-by: Fangrui Song <maskray@google.com>
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sedat Dilek <sedat.dilek@gmail.com>
Cc: llvm@lists.linux.dev
Link: https://lore.kernel.org/r/20211012021321.291635-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Sohaib Mohamed started a serie of tiny and incomplete checkpatch fixes but
seemingly stopped halfway -- take over and do most of it.
This is still missing net/9p/trans* and net/9p/protocol.c for a later
time...
Link: http://lkml.kernel.org/r/20211102134608.1588018-3-dominique.martinet@atmark-techno.com
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
|
|
having a readahead of 128k with a msize of 128k (with overhead) lead to
reading 124+4k everytime, making two roundtrips needlessly.
tune readahead according to msize when cache is enabled for better
performance
Link: http://lkml.kernel.org/r/20211104120323.2189376-1-asmadeus@codewreck.org
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
|
|
We need to cleanup resources on the probe() callback registered
with __register_blkdev(), now that add_disk() error handling is
supported. Address this.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20211103230437.1639990-14-mcgrof@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We need to cleanup resources on the probe() callback registered
with __register_blkdev(), now that add_disk() error handling is
supported. Address this.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20211103230437.1639990-13-mcgrof@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
__register_blkdev() is used to register a probe callback, and
that callback is typically used to call add_disk(). Now that
we are able to capture errors for add_disk(), we need to fix
those probe calls where add_disk() fails and clean up resources.
We don't extend the probe call to return the error given:
1) we'd have to always special-case the case where the disk
was already present, as otherwise concurrent requests to
open an existing block device would fail, and this would be
a userspace visible change
2) the error from ilookup() on blkdev_get_no_open() is sufficient
3) The only thing the probe call is used for is to support
pre-devtmpfs, pre-udev semantics that want to create disks when
their pre-created device node is accessed, and so we don't care
for failures on probe there.
Expand documentation for the probe callback to ensure users cleanup
resources if add_disk() is used and to clarify this interface may be
removed in the future.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20211103230437.1639990-12-mcgrof@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit bf9c0538e485b591 ("ataflop: use a separate gendisk for each media
format") introduced ataflop_probe_lock mutex, but forgot to unlock the
mutex when atari_floppy_init() (i.e. module loading) succeeded. This will
result in double lock deadlock if ataflop_probe() is called. Also,
unregister_blkdev() must not be called from atari_floppy_init() with
ataflop_probe_lock held when atari_floppy_init() failed, for
ataflop_probe() waits for ataflop_probe_lock with major_names_lock held
(i.e. AB-BA deadlock).
__register_blkdev() needs to be called last in order to avoid calling
ataflop_probe() when atari_floppy_init() is about to fail, for memory for
completing already-started ataflop_probe() safely will be released as soon
as atari_floppy_init() released ataflop_probe_lock mutex.
As with commit 8b52d8be86d72308 ("loop: reorder loop_exit"),
unregister_blkdev() needs to be called first in order to avoid calling
ataflop_alloc_disk() from ataflop_probe() after del_gendisk() from
atari_floppy_exit().
By relocating __register_blkdev() / unregister_blkdev() as explained above,
we can remove ataflop_probe_lock mutex, for probe function and __exit
function are serialized by major_names_lock mutex.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: bf9c0538e485b591 ("ataflop: use a separate gendisk for each media format")
Reviewed-by: Luis Chamberlain <mcgrof@kernel.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Link: https://lore.kernel.org/r/20211103230437.1639990-11-mcgrof@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We never checked for errors on add_disk() as this function
returned void. Now that this is fixed, use the shiny new
error handling.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20211103230437.1639990-10-mcgrof@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We never checked for errors on add_disk() as this function
returned void. Now that this is fixed, use the shiny new
error handling.
We re-use the same free tag call, so we also add a label for
that as well.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20211103230437.1639990-9-mcgrof@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We never checked for errors on add_disk() as this function
returned void. Now that this is fixed, use the shiny new
error handling. Only the disk is cleaned up inside
z2ram_register_disk() as the caller deals with the rest.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20211103230437.1639990-8-mcgrof@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Now that device_add_disk() supports returning an error, use
that. We must unwind alloc_dax() on error.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20211103230437.1639990-7-mcgrof@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Prior to devm being able to use pmem_release_disk() there are other
failure which can occur for which we must account for and release the
disk for. Address those few cases.
Fixes: 3dd60fb9d95d ("nvdimm/pmem: stop using q_usage_count as external pgmap refcount")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20211103230437.1639990-6-mcgrof@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We never checked for errors on add_disk() as this function
returned void. Now that this is fixed, use the shiny new
error handling.
Since nvdimm/blk uses devm we just need to move the devm
registration towards the end. And in hindsight, that seems
to also provide a fix given del_gendisk() should not be
called unless the disk was already added via add_disk().
The probably of that issue happening is low though, like
OOM while calling devm_add_action(), so the fix is minor.
We manually unwind in case of add_disk() failure prior
to the devm registration.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20211103230437.1639990-5-mcgrof@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If nd_integrity_init() fails we'd get del_gendisk() called,
but that's not correct as we should only call that if we're
done with device_add_disk(). Fix this by providing unwinding
prior to the devm call being registered and moving the devm
registration to the very end.
This should fix calling del_gendisk() if nd_integrity_init()
fails. I only spotted this issue through code inspection. It
does not fix any real world bug.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20211103230437.1639990-4-mcgrof@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We never checked for errors on add_disk() as this function
returned void. Now that this is fixed, use the shiny new
error handling.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20211103230437.1639990-3-mcgrof@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This will make it easier to share common error paths.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20211103230437.1639990-2-mcgrof@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The assignment and operation there will be overwritten later, so
it should be deleted.
The clang_analyzer complains as follows:
drivers/block/loop.c:2330:2 warning:
Value stored to 'err' is never read
change in v2:
Repair the sending email box
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Link: https://lore.kernel.org/r/20211104064546.3074-1-luo.penghao@zte.com.cn
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In drbd_create_device(), the 'out_no_io_page' lable has called
blk_cleanup_disk() when return failed.
So remove the 'out_cleanup_disk' lable to avoid double free the
disk pointer.
Fixes: e92ab4eda516 ("drbd: add error handling support for add_disk()")
Signed-off-by: Wu Bo <wubo40@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/1636013229-26309-1-git-send-email-wubo40@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In commit 2214c0e77259 ("parisc: Move thread_info into task struct")
PA-RISC gained support for THREAD_INFO_IN_TASK while changes were
already underway to keep the CPU field in thread_info rather than move
it into task_struct when THREAD_INFO_IN_TASK is enabled. The result is a
broken build for all PA-RISC configs that enable SMP.
So let's partially revert that commit, and get rid of the ugly hack to
get at the offset of task_struct::cpu without having to include
linux/sched.h, and put the CPU field back where it was before.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: bcf9033e5449 ("sched: move CPU field back into thread_info if THREAD_INFO_IN_TASK=y")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
I no longer think interrupts can be disabled in the futex and cmpxchg
operations because of COW breaks. This not ideal but I suspect it's the
best we can do.
For the cmpxchg operations in syscall.S, we rely on the code to not
schedule off the gateway page. For the futex, I added code to disable
preemption.
So far, I haven't seen the warnings with the attached change but the
change is only lightly tested.
Signed-off-by: Dave Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
If the previous context had interrupts disabled, we should better
keep them disabled. This was noticed in the unwinding code where
a copy_from_kernel_nofault() triggered a page fault, and after
the fixup by the page fault handler interrupts where suddenly
enabled.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Syzbot triggered the following warning in ovl_workdir_create() ->
ovl_create_real():
if (!err && WARN_ON(!newdentry->d_inode)) {
The reason is that the cgroup2 filesystem returns from mkdir without
instantiating the new dentry.
Weird filesystems such as this will be rejected by overlayfs at a later
stage during setup, but to prevent such a warning, call ovl_mkdir_real()
directly from ovl_workdir_create() and reject this case early.
Reported-and-tested-by: syzbot+75eab84fd0af9e8bf66b@syzkaller.appspotmail.com
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The usual collection of clk driver updates and new driver additions.
In terms of lines it's mainly Qualcomm and Mediatek code, supporting
various SoCs and their multitude of clk controllers.
New Drivers:
- GCC and RPMcc support for Qualcomm QCM2290 SoCs
- GCC support for Qualcomm MSM8994/MSM8992 SoCs
- LPASSCC and CAMCC support for Qualcomm SC7280 SoCs
- Support for Mediatek MT8195 SoCs
- Initial clock driver for the Exynos850 SoC
- Add i.MX8ULP clock driver and related bindings
Updates:
- Clock power management for new SAMA7G5 SoC
- Updates to the master clock driver and sam9x60-pll to be able to
use cpufreq-dt driver and avoid overclocking of CPU and MCK0
domains while changing the frequency via DVFS
- Use ARRAY_SIZE in qcom clk drivers
- Remove some impractical fallback parent names in qcom clk drivers
- Make Mediatek clk drivers tristate
- Refactoring of the CPU clock code and conversion of Samsung
Exynos5433 CPU clock driver to the platform driver
- A few conversions to devm_platform_ioremap_resource()
- Updates of the Samsung Kconfig help text
- Update video path realted clocks for Amlogic meson8
- Add SPI Multi I/O Bus and SDHI clocks and resets on Renesas RZ/G2L
- Add SPI Multi I/O Bus (RPC) clocks on Renesas R-Car V3U
- Add MediaLB clocks on Renesas R-Car H3, M3-W/W+, and M3-N
- Remove unused helpers from i.MX specific clock header
- Rework all i.MX clk based helpers to use clk_hw based ones
- Rework i.MX gate/mux/divider wrappers
- Rework imx_clk_hw_composite and imx_clk_hw_pll14xx wrappers
- Update i.MX pllv4 and composite clocks to support i.MX8ULP
- Disable i.MX7ULP composite clock during initialization
- Add CLK_SET_RATE_NO_REPARENT flag to the i.MX7ULP composite
- Disable the i.MX pfd when set pfdv2 clock rate
- Add support for i.MX8ULP in pfdv2
- Add the pcc reset controller support on i.MX8ULP
- Fix the build break when clk-imx8ulp is built as module
- Move csi_sel mux to correct base register in i.MX6UL clock drivr
- Fix csi clk gate register in i.MX6UL clock driver
- Fix build bug making CLK_IMX8ULP select MXC_CLK
- Add TPU (PWM), and Z (Cortex-A76) clocks on Renesas R-Car V3U
- Add Ethernet clocks on Renesas RZ/G2L
- Move Rockchip to use module_platform_probe
- Enable usage of Coresight related clocks on Rockchip rk3399"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (170 commits)
clk: use clk_core_get_rate_recalc() in clk_rate_get()
clk: at91: sama7g5: set low limit for mck0 at 32KHz
clk: at91: sama7g5: remove prescaler part of master clock
clk: at91: clk-master: add notifier for divider
clk: at91: clk-sam9x60-pll: add notifier for div part of PLL
clk: at91: clk-master: fix prescaler logic
clk: at91: clk-master: mask mckr against layout->mask
clk: at91: clk-master: check if div or pres is zero
clk: at91: sam9x60-pll: use DIV_ROUND_CLOSEST_ULL
clk: at91: pmc: add sama7g5 to the list of available pmcs
clk: at91: clk-master: improve readability by using local variables
clk: at91: clk-master: add register definition for sama7g5's master clock
clk: at91: sama7g5: add securam's peripheral clock
clk: at91: pmc: execute suspend/resume only for backup mode
clk: at91: re-factor clocks suspend/resume
clk: ux500: Add driver for the reset portions of PRCC
dt-bindings: clock: u8500: Rewrite in YAML and extend
clk: composite: Use rate_ops.determine_rate when also a mux is available
clk: samsung: describe drivers in Kconfig
clk: samsung: exynos5433: update apollo and atlas clock probing
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM defconfig updates from Arnd Bergmann:
"These are the usual changes to enable newly added driver by default,
and to do some housekeeping around changing Kconfig symbols"
* tag 'defconfig-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (33 commits)
arm64: defconfig: Enable Qualcomm LMH driver
arm64: defconfig: Enable Qualcomm prima/pronto drivers
arm64: defconfig: Enable Sleep stats driver
arm64: defconfig: Visconti: Enable PCIe host controller
ARM: configs: aspeed: Remove unused USB gadget devices
ARM: config: aspeed: Enable Network Block Device
ARM: configs: aspeed: Enable pstore and lockup detectors
ARM: configs: aspeed: Enable commonly used drivers
ARM: configs: aspeed: Disable IPV6 SIT device
ARM: imx_v6_v7_defconfig: Enable HID I2C
arm64: defconfig: Enable QTI SC7280 pinctrl, gcc and interconnect
arm64: defconfig: Disable firmware sysfs fallback
ARM: mvebu_v7_defconfig: rebuild default configuration
ARM: mvebu_v7_defconfig: enable mtd physmap
arm64: defconfig: Enable few Tegra210 based AHUB drivers
arm64: defconfig: drop obsolete ARCH_* configs
ARM: imx_v6_v7_defconfig: enable bpf syscall and cgroup bpf
ARM: imx_v6_v7_defconfig: build imx sdma driver as module
ARM: imx_v6_v7_defconfig: rebuild default configuration
ARM: imx_v6_v7_defconfig: change snd soc tlv320aic3x to i2c variant
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are all the driver updates for SoC specific drivers. There are a
couple of subsystems with individual maintainers picking up their
patches here:
- The reset controller subsystem add support for a few new SoC
variants to existing drivers, along with other minor improvements
- The OP-TEE subsystem gets a driver for the ARM FF-A transport
- The memory controller subsystem has improvements for Tegra,
Mediatek, Renesas, Freescale and Broadcom specific drivers.
- The tegra cpuidle driver changes get merged through this tree this
time. There are only minor changes, but they depend on other tegra
driver updates here.
- The ep93xx platform finally moves to using the drivers/clk/
subsystem, moving the code out of arch/arm in the process. This
depends on a small sound driver change that is included here as
well.
- There are some minor updates for Qualcomm and Tegra specific
firmware drivers.
The other driver updates are mainly for drivers/soc, which contains a
mixture of vendor specific drivers that don't really fit elsewhere:
- Mediatek drivers gain more support for MT8192, with new support for
hw-mutex and mmsys routing, plus support for reset lines in the
mmsys driver.
- Qualcomm gains a new "sleep stats" driver, and support for the
"Generic Packet Router" in the APR driver.
- There is a new user interface for routing the UARTS on ASpeed BMCs,
something that apparently nobody else has needed so far.
- More drivers can now be built as loadable modules, in particular
for Broadcom and Samsung platforms.
- Lots of improvements to the TI sysc driver for better
suspend/resume support"
Finally, there are lots of minor cleanups and new device IDs for
amlogic, renesas, tegra, qualcomm, mediateka, samsung, imx,
layerscape, allwinner, broadcom, and omap"
* tag 'drivers-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (179 commits)
optee: Fix spelling mistake "reclain" -> "reclaim"
Revert "firmware: qcom: scm: Add support for MC boot address API"
qcom: spm: allow compile-testing
firmware: arm_ffa: Remove unused 'compat_version' variable
soc: samsung: exynos-chipid: add exynosautov9 SoC support
firmware: qcom: scm: Don't break compile test on non-ARM platforms
soc: qcom: smp2p: Add of_node_put() before goto
soc: qcom: apr: Add of_node_put() before return
soc: qcom: qcom_stats: Fix client votes offset
soc: qcom: rpmhpd: fix sm8350_mxc's peer domain
dt-bindings: arm: cpus: Document qcom,msm8916-smp enable-method
ARM: qcom: Add qcom,msm8916-smp enable-method identical to MSM8226
firmware: qcom: scm: Add support for MC boot address API
soc: qcom: spm: Add 8916 SPM register data
dt-bindings: soc: qcom: spm: Document qcom,msm8916-saw2-v3.0-cpu
soc: qcom: socinfo: Add PM8150C and SMB2351 models
firmware: qcom_scm: Fix error retval in __qcom_scm_is_call_available()
soc: aspeed: Add UART routing support
soc: fsl: dpio: rename the enqueue descriptor variable
soc: fsl: dpio: use an explicit NULL instead of 0
...
|
|
Pull ARM SoC DT updates from Arnd Bergmann:
"This is a rather large update for the ARM devicetree files, after a
few quieter releases, with 775 total commits and 47 branches pulled
into this one.
There are 5 new SoC types plus some minor variations, and a total of
60 new machines, so I'm limiting the summary to the main noteworthy
items:
- Apple M1 gain support for PCI and pinctrl, getting a bit closer to
a usable system out of the box.
- Qualcomm gains support for Snapdragon 690 (aka SM6350) as well as
SM7225, 11 new smartphones, and three additional Chromebooks, and
improvements all over the place.
- Samsung gains support for ExynosAutov9, an automotive version of
their smartphone SoC, but otherwise no major changes.
- Microchip adds the SAMA5D29 SoC in the SAMA5 family, and a number
of improvements for the recently added SAMA7 family. The LAN966 SoC
that was added in the platform code does not have dts files yet.
Two board files are added for the older at91sam9g20 SoC
- Aspeed supports two additional server boards using their AST2600 as
BMC, and improves support for qemu models
- Rockchip RK3566/RK3688 gets added, along with six new development
boards using RK3328/RK3399/RK3566, and one Chromebook tablet.
- Two NAS boxes are added using the ARMv4 based Gemini platform
- One new board is added to the Intel Arria SoC FPGA family
- Marvell adds one network switch based on Armada 381 and the new
MOCHAbin 7040 development board
- NXP adds support for the S32G2 automotive SoC, two imx6 based ebook
readers, and three additional development boards, which is notably
less than their usual additions, but they also gain improvements to
their many existing boards
- STmicroelectronics adds their stm32mp13 SoC family along with a
reference board
- Renesas adds new versions of their R-Car Gen3 SoCs and many updates
for their older generations
- Broadcom adds support for a number of Cisco Meraki wireless
controllers, along with two new boards and other updates for
BCM53xx/BCM47xx networking SoCs and the Raspberry Pi boards
- Mediatek improves support for the MT81xx SoCs used in Chromebooks
as well as the MT76xx networking SoCs
- NVIDIA adds a number of cleanups and additional support for more
hardware on the already supported machines
- TI K3 adds support for three new boards along with cleanups
- Toshiba adds one board for the Visconti family
- Xilinx adds five new ZynqMP based machines
- Amlogic support is added for the Radxa Zero and two Jethub home
automation controllers, along with changes to other machines
- Rob Herring continues his work on fixing dtc warnings all over the
tree.
- Minor updates for TI OMAP, Mstar, Allwinner/sunxi, Hisilicon,
Ux500, Unisoc"
* tag 'dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (720 commits)
arm64: dts: apple: j274: Expose PCI node for the Ethernet MAC address
arm64: dts: apple: t8103: Add root port interrupt routing
arm64: dts: apple: t8103: Add PCIe DARTs
arm64: apple: Add PCIe node
arm64: apple: Add pinctrl nodes
ARM: dts: arm: Update ICST clock nodes 'reg' and node names
ARM: dts: arm: Update register-bit-led nodes 'reg' and node names
arm64: dts: exynos: add chipid node for exynosautov9 SoC
ARM: dts: qcom: fix typo in IPQ8064 thermal-sensor node
Revert "arm64: dts: qcom: msm8916-asus-z00l: Add sensors"
arm64: dts: qcom: ipq6018: Remove unused 'iface_clk' property from dma-controller node
arm64: dts: qcom: ipq6018: Remove unused 'qcom,config-pipe-trust-reg' property
arm64: dts: qcom: sm8350: Add CPU topology and idle-states
arm64: dts: qcom: Drop unneeded extra device-specific includes
arm64: dts: qcom: msm8916: Drop standalone smem node
arm64: dts: qcom: Fix node name of rpm-msg-ram device nodes
arm64: dts: qcom: msm8916-asus-z00l: Add sensors
arm64: dts: qcom: msm8916-asus-z00l: Add SDCard
arm64: dts: qcom: msm8916-asus-z00l: Add touchscreen
arm64: dts: qcom: sdm845-oneplus: remove devinfo-size from ramoops node
...
|
|
Pull ARM SoC updates from Arnd Bergmann:
"The SoC updates this time are mainly removing obsolete code from the
OMAP2 platform, another step in the eternal cleanup of that platform.
There are two new SoCs getting added: STMicroelectronics stm32mp13 and
Microchip lan966. Both fit into existing platforms and require minimal
changes here.
A couple of MAINTAINER file updates relate to those changes, and
update some file paths"
* tag 'soc-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (28 commits)
MAINTAINERS: Update BCM7XXX entry with additional patterns
MAINTAINERS: add pinctrl-apple-gpio to ARM/APPLE MACHINE
MAINTAINERS: Add pasemi i2c to ARM/APPLE MACHINE
ARM: SPEAr: Update MAINTAINERS entries
ARM: OMAP2+: Drop unused CM defines for am3
ARM: OMAP2+: Drop unused CM and SCRM defines for omap4
ARM: OMAP2+: Drop unused CM and SCRM defines for omap5
ARM: OMAP2+: Drop unused CM defines for dra7
ARM: OMAP2+: Drop unused PRM defines for am3
ARM: OMAP2+: Drop unused PRM defines for am4
ARM: OMAP2+: Drop unused PRM defines for omap4
ARM: OMAP2+: Drop unused PRM defines for omap5
ARM: OMAP2+: Drop unused PRM defines for dra7
ARM: OMAP2+: Fix comment typo
ARM: OMAP2+: Fix typo in some comments
ARM: at91: add basic support for new SoC family lan966
dt-bindings: arm: at91: Document lan966 pcb8291 and pcb8290 boards
ARM: at91: Documentation: add lan966 family
ARM: at91: Documentation: add sama7g5 family
MAINTAINERS: add an entry for NXP S32G boards
...
|
|
Pull virtio updates from Michael Tsirkin:
"vhost and virtio fixes and features:
- Hardening work by Jason
- vdpa driver for Alibaba ENI
- Performance tweaks for virtio blk
- virtio rng rework using an internal buffer
- mac/mtu programming for mlx5 vdpa
- Misc fixes, cleanups"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (45 commits)
vdpa/mlx5: Forward only packets with allowed MAC address
vdpa/mlx5: Support configuration of MAC
vdpa/mlx5: Fix clearing of VIRTIO_NET_F_MAC feature bit
vdpa_sim_net: Enable user to set mac address and mtu
vdpa: Enable user to set mac and mtu of vdpa device
vdpa: Use kernel coding style for structure comments
vdpa: Introduce query of device config layout
vdpa: Introduce and use vdpa device get, set config helpers
virtio-scsi: don't let virtio core to validate used buffer length
virtio-blk: don't let virtio core to validate used length
virtio-net: don't let virtio core to validate used length
virtio_ring: validate used buffer length
virtio_blk: correct types for status handling
virtio_blk: allow 0 as num_request_queues
i2c: virtio: Add support for zero-length requests
virtio-blk: fixup coccinelle warnings
virtio_ring: fix typos in vring_desc_extra
virtio-pci: harden INTX interrupts
virtio_pci: harden MSI-X interrupts
virtio_config: introduce a new .enable_cbs method
...
|
