summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-02-25batman-adv: Fix internal interface indices typesSven Eckelmann
batman-adv uses internal indices for each enabled and active interface. It is currently used by the B.A.T.M.A.N. IV algorithm to identifify the correct position in the ogm_cnt bitmaps. The type for the number of enabled interfaces (which defines the next interface index) was set to char. This type can be (depending on the architecture) either signed (limiting batman-adv to 127 active slave interfaces) or unsigned (limiting batman-adv to 255 active slave interfaces). This limit was not correctly checked when an interface was enabled and thus an overflow happened. This was only catched on systems with the signed char type when the B.A.T.M.A.N. IV code tried to resize its counter arrays with a negative size. The if_num interface index was only a s16 and therefore significantly smaller than the ifindex (int) used by the code net code. Both &batadv_hard_iface->if_num and &batadv_priv->num_ifaces must be (unsigned) int to support the same number of slave interfaces as the net core code. And the interface activation code must check the number of active slave interfaces to avoid integer overflows. Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-25netfilter: don't set F_IFACE on ipv6 fib lookupsFlorian Westphal
"fib" starts to behave strangely when an ipv6 default route is added - the FIB lookup returns a route using 'oif' in this case. This behaviour was inherited from ip6tables rpfilter so change this as well. Bugzilla: https://bugzilla.netfilter.org/show_bug.cgi?id=1221 Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2018-02-25netfilter: increase IPSTATS_MIB_CSUMERRORS statTaehee Yoo
In the ip_rcv, IPSTATS_MIB_CSUMERRORS is increased when checksum error is occurred. bridge netfilter routine should increase IPSTATS_MIB_CSUMERRORS. Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2018-02-25batman-adv: Fix netlink dumping of BLA backbonesSven Eckelmann
The function batadv_bla_backbone_dump_bucket must be able to handle non-complete dumps of a single bucket. It tries to do that by saving the latest dumped index in *idx_skip to inform the caller about the current state. But the caller only assumes that buckets were not completely dumped when the return code is non-zero. This function must therefore also return a non-zero index when the dumping of an entry failed. Otherwise the caller will just skip all remaining buckets. And the function must also reset *idx_skip back to zero when it finished a bucket. Otherwise it will skip the same number of entries in the next bucket as the previous one had. Fixes: ea4152e11716 ("batman-adv: add backbone table netlink support") Reported-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-25batman-adv: Fix netlink dumping of BLA claimsSven Eckelmann
The function batadv_bla_claim_dump_bucket must be able to handle non-complete dumps of a single bucket. It tries to do that by saving the latest dumped index in *idx_skip to inform the caller about the current state. But the caller only assumes that buckets were not completely dumped when the return code is non-zero. This function must therefore also return a non-zero index when the dumping of an entry failed. Otherwise the caller will just skip all remaining buckets. And the function must also reset *idx_skip back to zero when it finished a bucket. Otherwise it will skip the same number of entries in the next bucket as the previous one had. Fixes: 04f3f5bf1883 ("batman-adv: add B.A.T.M.A.N. Dump BLA claims via netlink") Reported-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-25batman-adv: Ignore invalid batadv_v_gw during netlink sendSven Eckelmann
The function batadv_v_gw_dump stops the processing loop when batadv_v_gw_dump_entry returns a non-0 return code. This should only happen when the buffer is full. Otherwise, an empty message may be returned by batadv_gw_dump. This empty message will then stop the netlink dumping of gateway entries. At worst, not a single entry is returned to userspace even when plenty of possible gateways exist. Fixes: b71bb6f924fe ("batman-adv: add B.A.T.M.A.N. V bat_gw_dump implementations") Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-25batman-adv: Ignore invalid batadv_iv_gw during netlink sendSven Eckelmann
The function batadv_iv_gw_dump stops the processing loop when batadv_iv_gw_dump_entry returns a non-0 return code. This should only happen when the buffer is full. Otherwise, an empty message may be returned by batadv_gw_dump. This empty message will then stop the netlink dumping of gateway entries. At worst, not a single entry is returned to userspace even when plenty of possible gateways exist. Fixes: efb766af06e3 ("batman-adv: add B.A.T.M.A.N. IV bat_gw_dump implementations") Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-25netfilter: nf_flow_table: fix checksum when handling DNATFelix Fietkau
Add a missing call to csum_replace4 like on SNAT. Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2018-02-25netfilter: ebtables: CONFIG_COMPAT: don't trust userland offsetsFlorian Westphal
We need to make sure the offsets are not out of range of the total size. Also check that they are in ascending order. The WARN_ON triggered by syzkaller (it sets panic_on_warn) is changed to also bail out, no point in continuing parsing. Briefly tested with simple ruleset of -A INPUT --limit 1/s' --log plus jump to custom chains using 32bit ebtables binary. Reported-by: <syzbot+845a53d13171abf8bf29@syzkaller.appspotmail.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2018-02-25netfilter: ebtables: convert BUG_ONs to WARN_ONsFlorian Westphal
All of these conditions are not fatal and should have been WARN_ONs from the get-go. Convert them to WARN_ONs and bail out. Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2018-02-25netfilter: bridge: ebt_among: add missing match size checksFlorian Westphal
ebt_among is special, it has a dynamic match size and is exempt from the central size checks. Therefore it must check that the size of the match structure provided from userspace is sane by making sure em->match_size is at least the minimum size of the expected structure. The module has such a check, but its only done after accessing a structure that might be out of bounds. tested with: ebtables -A INPUT ... \ --among-dst fe:fe:fe:fe:fe:fe --among-dst fe:fe:fe:fe:fe:fe --among-src fe:fe:fe:fe:ff:f,fe:fe:fe:fe:fe:fb,fe:fe:fe:fe:fc:fd,fe:fe:fe:fe:fe:fd,fe:fe:fe:fe:fe:fe --among-src fe:fe:fe:fe:ff:f,fe:fe:fe:fe:fe:fa,fe:fe:fe:fe:fe:fd,fe:fe:fe:fe:fe:fe,fe:fe:fe:fe:fe:fe Reported-by: <syzbot+fe0b19af568972814355@syzkaller.appspotmail.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2018-02-25netfilter: ipv6: fix use-after-free Write in nf_nat_ipv6_manip_pktFlorian Westphal
l4proto->manip_pkt() can cause reallocation of skb head so pointer to the ipv6 header must be reloaded. Reported-and-tested-by: <syzbot+10005f4292fc9cc89de7@syzkaller.appspotmail.com> Fixes: 58a317f1061c89 ("netfilter: ipv6: add IPv6 NAT support") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2018-02-25netfilter: ipt_CLUSTERIP: put config instead of freeing itFlorian Westphal
Once struct is added to per-netns list it becomes visible to other cpus, so we cannot use kfree(). Also delay setting entries refcount to 1 until after everything is initialised so that when we call clusterip_config_put() in this spot entries is still zero. Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2018-02-25netfilter: ipt_CLUSTERIP: put config struct if we can't increment ct refcountFlorian Westphal
This needs to put() the entry to avoid a resource leak in error path. Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2018-02-25batman-adv: invalidate checksum on fragment reassemblyMatthias Schiffer
A more sophisticated implementation could try to combine fragment checksums when all fragments have CHECKSUM_COMPLETE and are split at even offsets. For now, we just set ip_summed to CHECKSUM_NONE to avoid "hw csum failure" warnings in the kernel log when fragmented frames are received. In consequence, skb_pull_rcsum() can be replaced with skb_pull(). Note that in usual setups, packets don't reach batman-adv with CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see batadv's ethtype?), which is why the log messages do not occur on every system using batman-adv. I could reproduce this issue by stacking batman-adv on top of a VXLAN interface. Fixes: 610bfc6bc99b ("batman-adv: Receive fragmented packets and merge") Tested-by: Maximilian Wilhelm <max@sdn.clinic> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-25batman-adv: fix packet checksum in receive pathMatthias Schiffer
eth_type_trans() internally calls skb_pull(), which does not adjust the skb checksum; skb_postpull_rcsum() is necessary to avoid log spam of the form "bat0: hw csum failure" when packets with CHECKSUM_COMPLETE are received. Note that in usual setups, packets don't reach batman-adv with CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see batadv's ethtype?), which is why the log messages do not occur on every system using batman-adv. I could reproduce this issue by stacking batman-adv on top of a VXLAN interface. Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol") Tested-by: Maximilian Wilhelm <max@sdn.clinic> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-02-25md/raid1: fix NULL pointer dereferenceYufen Yu
In handle_write_finished(), if r1_bio->bios[m] != NULL, it thinks the corresponding conf->mirrors[m].rdev is also not NULL. But, it is not always true. Even if some io hold replacement rdev(i.e. rdev->nr_pending.count > 0), raid1_remove_disk() can also set the rdev as NULL. That means, bios[m] != NULL, but mirrors[m].rdev is NULL, resulting in NULL pointer dereference in handle_write_finished and sync_request_write. This patch can fix BUGs as follows: BUG: unable to handle kernel NULL pointer dereference at 0000000000000140 IP: [<ffffffff815bbbbd>] raid1d+0x2bd/0xfc0 PGD 12ab52067 PUD 12f587067 PMD 0 Oops: 0000 [#1] SMP CPU: 1 PID: 2008 Comm: md3_raid1 Not tainted 4.1.44+ #130 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1.fc26 04/01/2014 Call Trace: ? schedule+0x37/0x90 ? prepare_to_wait_event+0x83/0xf0 md_thread+0x144/0x150 ? wake_atomic_t_function+0x70/0x70 ? md_start_sync+0xf0/0xf0 kthread+0xd8/0xf0 ? kthread_worker_fn+0x160/0x160 ret_from_fork+0x42/0x70 ? kthread_worker_fn+0x160/0x160 BUG: unable to handle kernel NULL pointer dereference at 00000000000000b8 IP: sync_request_write+0x9e/0x980 PGD 800000007c518067 P4D 800000007c518067 PUD 8002b067 PMD 0 Oops: 0000 [#1] SMP PTI CPU: 24 PID: 2549 Comm: md3_raid1 Not tainted 4.15.0+ #118 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1.fc26 04/01/2014 Call Trace: ? sched_clock+0x5/0x10 ? sched_clock_cpu+0xc/0xb0 ? flush_pending_writes+0x3a/0xd0 ? pick_next_task_fair+0x4d5/0x5f0 ? __switch_to+0xa2/0x430 raid1d+0x65a/0x870 ? find_pers+0x70/0x70 ? find_pers+0x70/0x70 ? md_thread+0x11c/0x160 md_thread+0x11c/0x160 ? finish_wait+0x80/0x80 kthread+0x111/0x130 ? kthread_create_worker_on_cpu+0x70/0x70 ? do_syscall_64+0x6f/0x190 ? SyS_exit_group+0x10/0x10 ret_from_fork+0x35/0x40 Reviewed-by: NeilBrown <neilb@suse.com> Signed-off-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
2018-02-25md: fix a potential deadlock of raid5/raid10 reshapeBingJing Chang
There is a potential deadlock if mount/umount happens when raid5_finish_reshape() tries to grow the size of emulated disk. How the deadlock happens? 1) The raid5 resync thread finished reshape (expanding array). 2) The mount or umount thread holds VFS sb->s_umount lock and tries to write through critical data into raid5 emulated block device. So it waits for raid5 kernel thread handling stripes in order to finish it I/Os. 3) In the routine of raid5 kernel thread, md_check_recovery() will be called first in order to reap the raid5 resync thread. That is, raid5_finish_reshape() will be called. In this function, it will try to update conf and call VFS revalidate_disk() to grow the raid5 emulated block device. It will try to acquire VFS sb->s_umount lock. The raid5 kernel thread cannot continue, so no one can handle mount/ umount I/Os (stripes). Once the write-through I/Os cannot be finished, mount/umount will not release sb->s_umount lock. The deadlock happens. The raid5 kernel thread is an emulated block device. It is responible to handle I/Os (stripes) from upper layers. The emulated block device should not request any I/Os on itself. That is, it should not call VFS layer functions. (If it did, it will try to acquire VFS locks to guarantee the I/Os sequence.) So we have the resync thread to send resync I/O requests and to wait for the results. For solving this potential deadlock, we can put the size growth of the emulated block device as the final step of reshape thread. 2017/12/29: Thanks to Guoqing Jiang <gqjiang@suse.com>, we confirmed that there is the same deadlock issue in raid10. It's reproducible and can be fixed by this patch. For raid10.c, we can remove the similar code to prevent deadlock as well since they has been called before. Reported-by: Alex Wu <alexwu@synology.com> Reviewed-by: Alex Wu <alexwu@synology.com> Reviewed-by: Chung-Chiang Cheng <cccheng@synology.com> Signed-off-by: BingJing Chang <bingjingc@synology.com> Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
2018-02-25md-cluster: choose correct label when clustered layout is not supportedLidong Zhong
r10conf is already successfully allocated before checking the layout Signed-off-by: Lidong Zhong <lzhong@suse.com> Reviewed-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
2018-02-25fs: dcache: Use READ_ONCE when accessing i_dir_seqWill Deacon
i_dir_seq is subject to concurrent modification by a cmpxchg or store-release operation, so ensure that the relaxed access in d_alloc_parallel uses READ_ONCE. Reported-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2018-02-25fs: dcache: Avoid livelock between d_alloc_parallel and __d_addWill Deacon
If d_alloc_parallel runs concurrently with __d_add, it is possible for d_alloc_parallel to continuously retry whilst i_dir_seq has been incremented to an odd value by __d_add: CPU0: __d_add n = start_dir_add(dir); cmpxchg(&dir->i_dir_seq, n, n + 1) == n CPU1: d_alloc_parallel retry: seq = smp_load_acquire(&parent->d_inode->i_dir_seq) & ~1; hlist_bl_lock(b); bit_spin_lock(0, (unsigned long *)b); // Always succeeds CPU0: __d_lookup_done(dentry) hlist_bl_lock bit_spin_lock(0, (unsigned long *)b); // Never succeeds CPU1: if (unlikely(parent->d_inode->i_dir_seq != seq)) { hlist_bl_unlock(b); goto retry; } Since the simple bit_spin_lock used to implement hlist_bl_lock does not provide any fairness guarantees, then CPU1 can starve CPU0 of the lock and prevent it from reaching end_dir_add(dir), therefore CPU1 cannot exit its retry loop because the sequence number always has the bottom bit set. This patch resolves the livelock by not taking hlist_bl_lock in d_alloc_parallel if the sequence counter is odd, since any subsequent masked comparison with i_dir_seq will fail anyway. Cc: Peter Zijlstra <peterz@infradead.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Reported-by: Naresh Madhusudana <naresh.madhusudana@arm.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2018-02-25platform/x86: intel-vbtn: Only activate tablet mode switch on 2-in-1'sMario Limonciello
Some laptops such as the XPS 9360 support the intel-vbtn INT33D6 interface but don't initialize the bit that intel-vbtn uses to represent switching tablet mode. By running this only on real 2-in-1's it shouldn't cause false positives. Fixes: 30323fb6d5 ("Support tablet mode switch") Reported-by: Jeremy Cline <jeremy@jcline.org> Signed-off-by: Mario Limonciello <mario.limonciello@dell.com> Tested-by: Jeremy Cline <jeremy@jcline.org> Tested-by: Darren Hart (VMware) <dvhart@infradead.org> Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
2018-02-25radix tree test suite: Fix buildMatthew Wilcox
- Add an empty linux/compiler_types.h (now being included by kconfig.h) - Add __GFP_ZERO - Add kzalloc - Test __GFP_DIRECT_RECLAIM instead of __GFP_NOWARN Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
2018-02-25rtlwifi: rtl8723be: Fix loss of signalLarry Finger
In commit c713fb071edc ("rtlwifi: rtl8821ae: Fix connection lost problem correctly") a problem in rtl8821ae that caused loss of signal was fixed. That same problem has now been reported for rtl8723be. Accordingly, the ASPM L1 latency has been increased from 0 to 7 to fix the instability. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> Tested-by: James Cameron <quozl@laptop.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2018-02-25Merge tag 'iwlwifi-for-kalle-2018-02-16-2' of ↵Kalle Valo
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes First batch of iwlwifi fixes intended for 4.16: * A couple of bugzilla fixes - Fix a bogus warning when freeing a TFD; - Fix severe throughput problem with 9000 series; * Fix for a bug that caused queue hangs in certain situations; * Fix for an issue with IBSS; * Fix an issue with rate-scalingin AP-mode.
2018-02-24Merge tag 'powerpc-4.16-4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc fixes from Michael Ellerman: - Add handling for a missing instruction in our 32-bit BPF JIT so that it can be used for seccomp filtering. - Add a missing NULL pointer check before a function call in new EEH code. - Fix an error path in the new ocxl driver to correctly return EFAULT. - The support for the new ibm,drc-info device tree property turns out to need several fixes, so for now we just stop advertising to firmware that we support it until the bugs can be ironed out. - One fix for the new drmem code which was incorrectly modifying the device tree in place. - Finally two fixes for the RFI flush support, so that firmware can advertise to us that it should be disabled entirely so as not to affect performance. Thanks to: Bharata B Rao, Frederic Barrat, Juan J. Alvarez, Mark Lord, Michael Bringmann. * tag 'powerpc-4.16-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/powernv: Support firmware disable of RFI flush powerpc/pseries: Support firmware disable of RFI flush powerpc/mm/drmem: Fix unexpected flag value in ibm,dynamic-memory-v2 powerpc/bpf/jit: Fix 32-bit JIT for seccomp_data access powerpc/pseries: Revert support for ibm,drc-info devtree property powerpc/pseries: Fix duplicate firmware feature for DRC_INFO ocxl: Fix potential bad errno on irq allocation powerpc/eeh: Fix crashes in eeh_report_resume()
2018-02-24block: kyber: fix domain token leak during requeueMing Lei
When requeuing request, the domain token should have been freed before re-inserting the request to io scheduler. Otherwise, the assigned domain token will be leaked, and IO hang can be caused. Cc: Paolo Valente <paolo.valente@linaro.org> Cc: Omar Sandoval <osandov@fb.com> Cc: stable@vger.kernel.org Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-02-24blk-mq: don't call io sched's .requeue_request when requeueing rq to ->dispatchMing Lei
__blk_mq_requeue_request() covers two cases: - one is that the requeued request is added to hctx->dispatch, such as blk_mq_dispatch_rq_list() - another case is that the request is requeued to io scheduler, such as blk_mq_requeue_request(). We should call io sched's .requeue_request callback only for the 2nd case. Cc: Paolo Valente <paolo.valente@linaro.org> Cc: Omar Sandoval <osandov@fb.com> Fixes: bd166ef183c2 ("blk-mq-sched: add framework for MQ capable IO schedulers") Cc: stable@vger.kernel.org Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Acked-by: Paolo Valente <paolo.valente@linaro.org> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2018-02-24dt-bindings: iio: adc: sd-modulator: fix io-channel-cellsFabrice Gasnier
io-channel-cells should be <0> since sigma delta modulator exports only one channel, as described in ../iio/iio-bindings.txt "IIO providers" section. Only the phandle is necessary for IIO consumers in this case. Fixes: af11143757b7 ("IIO: Add DT bindings for sigma delta adc modulator") Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-02-24iio: adc: stm32-dfsdm: fix multiple channel initializationFabrice Gasnier
When several channels are registered (e.g. via st,adc-channels property): - channels array is wrongly filled in. Only 1st element in array is being initialized with last registered channel. Fix it by passing reference to relevant channel (e.g. array[index]). - only last initialized channel can work properly (e.g. unique 'ch_id' is used). Converting any other channel result in conversion timeout. Fix it by getting rid of 'ch_id', use chan->channel instead. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-02-24iio: adc: stm32-dfsdm: fix clock source selectionFabrice Gasnier
Add missing clock source selection. In case "audio" clock is provided, it's unused currently: "dfsdm" clock is wrongly used by default. Fixes: bed73904e76f ("IIO: ADC: add stm32 DFSDM core support") Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-02-24iio: adc: stm32-dfsdm: fix call to stop channelFabrice Gasnier
stm32_dfsdm_stop_channel must be called with channel id, not filter id. Fixes: e2e6771c6462 ("IIO: ADC: add STM32 DFSDM sigma delta ADC support") Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-02-24iio: adc: stm32-dfsdm: fix compatible data useFabrice Gasnier
Fix use of compatible data: stm32h7 regmap configuration is statically used. Rather use regmap_cfg from compatible data. Fixes: bed73904e76f ("IIO: ADC: add stm32 DFSDM core support") Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by: Arnaud Pouliquen <arnaud.pouliquen@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-02-24iio: chemical: ccs811: Corrected firmware boot/application mode transitionRichard Lai
CCS811 has different I2C register maps in boot and application mode. When CCS811 is in boot mode, register APP_START (0xF4) is used to transit the firmware state from boot to application mode. However, APP_START is not a valid register location when CCS811 is in application mode (refer to "CCS811 Bootloader Register Map" and "CCS811 Application Register Map" in CCS811 datasheet). The driver should not attempt to perform a write to APP_START while CCS811 is in application mode, as this is not a valid or documented register location. When prob function is being called, the driver assumes the CCS811 sensor is in boot mode, and attempts to perform a write to APP_START. Although CCS811 powers-up in boot mode, it may have already been transited to application mode by previous instances, e.g. unload and reload device driver by the system, or explicitly by user. Depending on the system design, CCS811 sensor may be permanently connected to system power source rather than power controlled by GPIO, hence it is possible that the sensor is never power reset, thus the firmware could be in either boot or application mode at any given time when driver prob function is being called. This patch checks the STATUS register before attempting to send a write to APP_START. Only if the firmware is not in application mode and has valid firmware application loaded, then it will continue to start transiting the firmware boot to application mode. Signed-off-by: Richard Lai <richard@richardman.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2018-02-24ALSA: usb-audio: Add a quirck for B&W PX headphonesErik Veijola
The capture interface doesn't work and the playback interface only supports 48 kHz sampling rate even though it advertises more rates. Signed-off-by: Erik Veijola <erik.veijola@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2018-02-24ALSA: hda: Add a power_save blacklistHans de Goede
On some boards setting power_save to a non 0 value leads to clicking / popping sounds when ever we enter/leave powersaving mode. Ideally we would figure out how to avoid these sounds, but that is not always feasible. This commit adds a blacklist for devices where powersaving is known to cause problems and disables it on these devices. Note I tried to put this blacklist in userspace first: https://github.com/systemd/systemd/pull/8128 But the systemd maintainers rightfully pointed out that it would be impossible to then later remove entries once we actually find a way to make power-saving work on listed boards without issues. Having this list in the kernel will allow removal of the blacklist entry in the same commit which fixes the clicks / plops. The blacklist only applies to the default power_save module-option value, if a user explicitly sets the module-option then the blacklist is not used. [ added an ifdef CONFIG_PM for the build error -- tiwai] BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1525104 BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=198611 Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2018-02-24ARM: dts: imx6dl: Include correct dtsi file for Engicam i.CoreM6 ↵Shyam Saini
DualLite/Solo RQS This patch fixes the wrongly included dtsi file which was breaking mainline support for Engicam i.CoreM6 DualLite/Solo RQS. As per the board name, the correct file should be imx6dl.dtsi instead of imx6q.dtsi Reported-by: Michael Trimarchi <michael@amarulasolutions.com> Suggested-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Shyam Saini <shyam@amarulasolutions.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Fixes: 7a9caba55a61 ("ARM: dts: imx6dl: Add Engicam i.CoreM6 DualLite/Solo RQS initial support") Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2018-02-23lock_parent() needs to recheck if dentry got __dentry_kill'ed under itAl Viro
In case when dentry passed to lock_parent() is protected from freeing only by the fact that it's on a shrink list and trylock of parent fails, we could get hit by __dentry_kill() (and subsequent dentry_kill(parent)) between unlocking dentry and locking presumed parent. We need to recheck that dentry is alive once we lock both it and parent *and* postpone rcu_read_unlock() until after that point. Otherwise we could return a pointer to struct dentry that already is rcu-scheduled for freeing, with ->d_lock held on it; caller's subsequent attempt to unlock it can end up with memory corruption. Cc: stable@vger.kernel.org # 3.12+, counting backports Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2018-02-24KVM: SVM: Fix SEV LAUNCH_SECRET commandBrijesh Singh
The SEV LAUNCH_SECRET command fails with error code 'invalid param' because we missed filling the guest and header system physical address while issuing the command. Fixes: 9f5b5b950aa9 (KVM: SVM: Add support for SEV LAUNCH_SECRET command) Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Borislav Petkov <bp@suse.de> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: linux-kernel@vger.kernel.org Cc: Joerg Roedel <joro@8bytes.org> Signed-off-by: Brijesh Singh <brijesh.singh@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2018-02-24KVM: SVM: install RSM interceptBrijesh Singh
RSM instruction is used by the SMM handler to return from SMM mode. Currently, rsm causes a #UD - which results in instruction fetch, decode, and emulate. By installing the RSM intercept we can avoid the instruction fetch since we know that #VMEXIT was due to rsm. The patch is required for the SEV guest, because in case of SEV guest memory is encrypted with guest-specific key and hypervisor will not able to fetch the instruction bytes from the guest memory. Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Joerg Roedel <joro@8bytes.org> Cc: Borislav Petkov <bp@suse.de> Cc: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Brijesh Singh <brijesh.singh@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2018-02-24KVM: SVM: no need to call access_ok() in LAUNCH_MEASURE commandBrijesh Singh
Using the access_ok() to validate the input before issuing the SEV command does not buy us anything in this case. If userland is giving us a garbage pointer then copy_to_user() will catch it when we try to return the measurement. Suggested-by: Al Viro <viro@ZenIV.linux.org.uk> Fixes: 0d0736f76347 (KVM: SVM: Add support for KVM_SEV_LAUNCH_MEASURE ...) Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Borislav Petkov <bp@suse.de> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: linux-kernel@vger.kernel.org Cc: Joerg Roedel <joro@8bytes.org> Signed-off-by: Brijesh Singh <brijesh.singh@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2018-02-24include: psp-sev: Capitalize invalid length enumBrijesh Singh
Commit 1d57b17c60ff ("crypto: ccp: Define SEV userspace ioctl and command id") added the invalid length enum but we missed capitalizing it. Fixes: 1d57b17c60ff (crypto: ccp: Define SEV userspace ioctl ...) Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Borislav Petkov <bp@suse.de> Cc: Tom Lendacky <thomas.lendacky@amd.com> CC: Gary R Hook <gary.hook@amd.com> Cc: linux-kernel@vger.kernel.org Signed-off-by: Brijesh Singh <brijesh.singh@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2018-02-24crypto: ccp: Fix sparse, use plain integer as NULL pointerBrijesh Singh
Fix sparse warning: Using plain integer as NULL pointer. Replaces assignment of 0 to pointer with NULL assignment. Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Borislav Petkov <bp@suse.de> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Gary Hook <gary.hook@amd.com> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: linux-crypto@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Brijesh Singh <brijesh.singh@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2018-02-24KVM: X86: Avoid traversing all the cpus for pv tlb flush when steal time is ↵Wanpeng Li
disabled Avoid traversing all the cpus for pv tlb flush when steal time is disabled since pv tlb flush depends on the field in steal time for shared data. Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim KrÄmář <rkrcmar@redhat.com> Signed-off-by: Wanpeng Li <wanpengli@tencent.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2018-02-24x86/kvm: Make parse_no_xxx __init for kvmDou Liyang
The early_param() is only called during kernel initialization, So Linux marks the functions of it with __init macro to save memory. But it forgot to mark the parse_no_kvmapf/stealacc/kvmclock_vsyscall, So, Make them __init as well. Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: rkrcmar@redhat.com Cc: kvm@vger.kernel.org Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Juergen Gross <jgross@suse.com> Cc: x86@kernel.org Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2018-02-24KVM: x86: fix backward migration with async_PFRadim Krčmář
Guests on new hypersiors might set KVM_ASYNC_PF_DELIVERY_AS_PF_VMEXIT bit when enabling async_PF, but this bit is reserved on old hypervisors, which results in a failure upon migration. To avoid breaking different cases, we are checking for CPUID feature bit before enabling the feature and nothing else. Fixes: 52a5c155cf79 ("KVM: async_pf: Let guest support delivery of async_pf from guest mode") Cc: <stable@vger.kernel.org> Reviewed-by: Wanpeng Li <wanpengli@tencent.com> Reviewed-by: David Hildenbrand <david@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2018-02-24kvm: fix warning for non-x86 buildsSebastian Ott
Fix the following sparse warning by moving the prototype of kvm_arch_mmu_notifier_invalidate_range() to linux/kvm_host.h . CHECK arch/s390/kvm/../../../virt/kvm/kvm_main.c arch/s390/kvm/../../../virt/kvm/kvm_main.c:138:13: warning: symbol 'kvm_arch_mmu_notifier_invalidate_range' was not declared. Should it be static? Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2018-02-24kvm: fix warning for CONFIG_HAVE_KVM_EVENTFD buildsSebastian Ott
Move the kvm_arch_irq_routing_update() prototype outside of ifdef CONFIG_HAVE_KVM_EVENTFD guards to fix the following sparse warning: arch/s390/kvm/../../../virt/kvm/irqchip.c:171:28: warning: symbol 'kvm_arch_irq_routing_update' was not declared. Should it be static? Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2018-02-24tools/kvm_stat: print 'Total' line for multiple events onlyStefan Raspl
The 'Total' line looks a bit weird when we have a single event only. This can happen e.g. due to filters. Therefore suppress when there's only a single event in the output. Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2018-02-24tools/kvm_stat: group child events indented after parentStefan Raspl
We keep the current logic that sorts all events (parent and child), but re-shuffle the events afterwards, grouping the children after the respective parent. Note that the percentage column for child events gives the percentage of the parent's total. Since we rework the logic anyway, we modify the total average calculation to use the raw numbers instead of the (rounded) averages. Note that this can result in differing numbers (between total average and the sum of the individual averages) due to rounding errors. Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
generated by cgit (git 2.34.1) at 2025-09-15 10:28:25 +0000