| Age | Commit message (Collapse) | Author |
|---|
|
When the TTY buffers fill up to the configured maximum, a system lockup
occurs:
[ 598.820128] INFO: rcu_preempt detected stalls on CPUs/tasks:
[ 598.825796] 0-...!: (1 GPs behind) idle=5a6/2/0 softirq=1974/1974 fqs=1
[ 598.832577] (detected by 3, t=62517 jiffies, g=296, c=295, q=126)
[ 598.838755] Task dump for CPU 0:
[ 598.841977] swapper/0 R running task 0 0 0 0x00000022
[ 598.849023] Call trace:
[ 598.851476] __switch_to+0x98/0xb0
[ 598.854870] (null)
This can be prevented by doing a dummy read of the RX data register.
This issue affects both HSCIF and SCIF ports. Reported for R-Car H3 ES2.0;
reproduced and fixed on H3 ES1.1. Probably affects other R-Car platforms
as well.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add PCI ids for two variants of Brainboxes UC-260 quad port
PCI serial cards.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It will get the wrong virtual address because port->mapbase is not added
the correct reg-offset yet. We have to update it before earlycon_map()
is called
Signed-off-by: Greentime Hu <greentime@andestech.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: stable@vger.kernel.org
Fixes: 088da2a17619 ("of: earlycon: Initialize port fields from DT properties")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is a followup on 44117a1d1732 ("serial: core: mark port as
initialized after successful IRQ change").
Nikola has been using autoconfig via setserial and reported a crash
similar to what I fixed in the earlier mentioned commit. Here I do the
same fixup for the autoconfig. I wasn't sure that this is the right
approach. Nikola confirmed that it fixes his crash.
Fixes: b3b576461864 ("tty: serial_core: convert uart_open to use tty_port_open")
Link: http://lkml.kernel.org/r/20180131072000.GD1853@localhost.localdomain
Reported-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Do not fail on multiport cards in serial_pci_is_class_communication().
It restores behaviour for SUNIX multiport cards, that enumerated by
class and have a custom board data.
Moreover it allows users to reenumerate port-by-port from user space.
Fixes: 7d8905d06405 ("serial: 8250_pci: Enable device after we check black list")
Reported-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On our at91sam9260 based board the usart0 and usart1 ports report
their versions (ATMEL_US_VERSION) as 0x10302. This version is not
included in the current checks in the driver.
Signed-off-by: Jonas Danielsson <jonas@orbital-systems.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A tty is hung up by __tty_hangup() setting file->f_op to
hung_up_tty_fops, which is skipped on ttys whose write operation isn't
tty_write(). This means that, for example, /dev/console whose write
op is redirected_tty_write() is never actually marked hung up.
Because n_tty_read() uses the hung up status to decide whether to
abort the waiting readers, the lack of hung-up marking can lead to the
following scenario.
1. A session contains two processes. The leader and its child. The
child ignores SIGHUP.
2. The leader exits and starts disassociating from the controlling
terminal (/dev/console).
3. __tty_hangup() skips setting f_op to hung_up_tty_fops.
4. SIGHUP is delivered and ignored.
5. tty_ldisc_hangup() is invoked. It wakes up the waits which should
clear the read lockers of tty->ldisc_sem.
6. The reader wakes up but because tty_hung_up_p() is false, it
doesn't abort and goes back to sleep while read-holding
tty->ldisc_sem.
7. The leader progresses to tty_ldisc_lock() in tty_ldisc_hangup()
and is now stuck in D sleep indefinitely waiting for
tty->ldisc_sem.
The following is Alan's explanation on why some ttys aren't hung up.
http://lkml.kernel.org/r/20171101170908.6ad08580@alans-desktop
1. It broke the serial consoles because they would hang up and close
down the hardware. With tty_port that *should* be fixable properly
for any cases remaining.
2. The console layer was (and still is) completely broken and doens't
refcount properly. So if you turn on console hangups it breaks (as
indeed does freeing consoles and half a dozen other things).
As neither can be fixed quickly, this patch works around the problem
by introducing a new flag, TTY_HUPPING, which is used solely to tell
n_tty_read() that hang-up is in progress for the console and the
readers should be aborted regardless of the hung-up status of the
device.
The following is a sample hung task warning caused by this issue.
INFO: task agetty:2662 blocked for more than 120 seconds.
Not tainted 4.11.3-dbg-tty-lockup-02478-gfd6c7ee-dirty #28
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
0 2662 1 0x00000086
Call Trace:
__schedule+0x267/0x890
schedule+0x36/0x80
schedule_timeout+0x23c/0x2e0
ldsem_down_write+0xce/0x1f6
tty_ldisc_lock+0x16/0x30
tty_ldisc_hangup+0xb3/0x1b0
__tty_hangup+0x300/0x410
disassociate_ctty+0x6c/0x290
do_exit+0x7ef/0xb00
do_group_exit+0x3f/0xa0
get_signal+0x1b3/0x5d0
do_signal+0x28/0x660
exit_to_usermode_loop+0x46/0x86
do_syscall_64+0x9c/0xb0
entry_SYSCALL64_slow_path+0x25/0x25
The following is the repro. Run "$PROG /dev/console". The parent
process hangs in D state.
#include <sys/types.h>
#include <sys/stat.h>
#include <sys/wait.h>
#include <sys/ioctl.h>
#include <fcntl.h>
#include <unistd.h>
#include <stdio.h>
#include <stdlib.h>
#include <errno.h>
#include <signal.h>
#include <time.h>
#include <termios.h>
int main(int argc, char **argv)
{
struct sigaction sact = { .sa_handler = SIG_IGN };
struct timespec ts1s = { .tv_sec = 1 };
pid_t pid;
int fd;
if (argc < 2) {
fprintf(stderr, "test-hung-tty /dev/$TTY\n");
return 1;
}
/* fork a child to ensure that it isn't already the session leader */
pid = fork();
if (pid < 0) {
perror("fork");
return 1;
}
if (pid > 0) {
/* top parent, wait for everyone */
while (waitpid(-1, NULL, 0) >= 0)
;
if (errno != ECHILD)
perror("waitpid");
return 0;
}
/* new session, start a new session and set the controlling tty */
if (setsid() < 0) {
perror("setsid");
return 1;
}
fd = open(argv[1], O_RDWR);
if (fd < 0) {
perror("open");
return 1;
}
if (ioctl(fd, TIOCSCTTY, 1) < 0) {
perror("ioctl");
return 1;
}
/* fork a child, sleep a bit and exit */
pid = fork();
if (pid < 0) {
perror("fork");
return 1;
}
if (pid > 0) {
nanosleep(&ts1s, NULL);
printf("Session leader exiting\n");
exit(0);
}
/*
* The child ignores SIGHUP and keeps reading from the controlling
* tty. Because SIGHUP is ignored, the child doesn't get killed on
* parent exit and the bug in n_tty makes the read(2) block the
* parent's control terminal hangup attempt. The parent ends up in
* D sleep until the child is explicitly killed.
*/
sigaction(SIGHUP, &sact, NULL);
printf("Child reading tty\n");
while (1) {
char buf[1024];
if (read(fd, buf, sizeof(buf)) < 0) {
perror("read");
return 1;
}
}
return 0;
}
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@llwyncelyn.cymru>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The tm-resched-dscr test links against pmu/lib.o, but we don't have a
rule to clean pmu/lib.o. This can lead to a build break if you build
for big endian and then little, or vice versa.
Fix it by making tm-resched-dscr depend on pmu/lib.c, causing the code
to be built directly in, meaning no .o is generated.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Once in a while I see build errors similar to the following
when building images from a clean tree.
Building powerpc:virtex-ml507:44x/virtex5_defconfig ... failed
------------
Error log:
arch/powerpc/boot/treeboot-akebono.c:37:20: fatal error:
libfdt.h: No such file or directory
Building powerpc:bamboo:smpdev:44x/bamboo_defconfig ... failed
------------
Error log:
arch/powerpc/boot/treeboot-akebono.c:37:20: fatal error:
libfdt.h: No such file or directory
arch/powerpc/boot/treeboot-currituck.c:35:20: fatal error:
libfdt.h: No such file or directory
Rebuilds will succeed.
Turns out that several source files in arch/powerpc/boot/ include
libfdt.h, but Makefile dependencies are incomplete. Let's fix that.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Normal 512-byte get/set of a TLV isn't supported but we were
registering the normal get/set anyway and relying on omitting
the SNDRV_CTL_ELEM_ACCESS_[READ|WRITE] flags to prevent them
being called.
Trouble is if this gets broken in the core ALSA code - as it has
been since at least 4.14 - the standard get/set can be called
unexpectedly and corrupt memory.
There's no point providing functions that won't be called and
it's a trivial change. The benefit is that if the ALSA core gets
broken again we get a big fat immediate NULL dereference instead
of a memory corruption timebomb.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
If multipathing is enabled, each NVMe subsystem creates a head
namespace (e.g., nvme0n1) and multiple private namespaces
(e.g., nvme0c0n1 and nvme0c1n1) in sysfs. When creating links for
private namespaces, links of head namespace are used, so the
namespace creation order must be followed (e.g., nvme0n1 ->
nvme0c1n1). If the order is not followed, links of sysfs will be
incomplete or kernel panic will occur.
The kernel panic was:
kernel BUG at fs/sysfs/symlink.c:27!
Call Trace:
nvme_mpath_add_disk_links+0x5d/0x80 [nvme_core]
nvme_validate_ns+0x5c2/0x850 [nvme_core]
nvme_scan_work+0x1af/0x2d0 [nvme_core]
Correct order
Context A Context B
nvme0n1
nvme0c0n1 nvme0c1n1
Incorrect order
Context A Context B
nvme0c1n1
nvme0n1
nvme0c0n1
The nvme_mpath_add_disk (for creating head namespace) is called
just before the nvme_mpath_add_disk_links (for creating private
namespaces). In nvme_mpath_add_disk, the first context acquires
the lock of subsystem and creates a head namespace, and other
contexts do nothing by checking GENHD_FL_UP of a head namespace
after waiting to acquire the lock. We verified the code with or
without multipathing using three vendors of dual-port NVMe SSDs.
Signed-off-by: Baegjae Sung <baegjae@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
|
|
Makes them easier to find.
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
To reproduce the lock up do the following
- connect otg host adapter and a USB device to the dual-role port
so that it is in host mode.
- suspend to mem.
- disconnect otg adapter.
- resume the system.
If we call dwc3_host_exit() before tasks are thawed
xhci_plat_remove() seems to lock up at the second usb_remove_hcd() call.
To work around this we queue the _dwc3_set_mode() work on
the system_freezable_wq.
Fixes: 41ce1456e1db ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: <stable@vger.kernel.org> # v4.12+
Suggested-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
When LPE audio driver gets some error at probing, it may lead to a
crash because of canceling the pending work in hdmi_lpe_audio_free(),
since some of ports might be still not initialized.
For assuring the proper free of each port, initialize all ports at the
beginning of the probe.
Fixes: b4eb0d522fcb ("ALSA: x86: Split snd_intelhad into card and PCM specific structures")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The commit change for supporting the multiple ports moved involved
some code shuffling, and there the initializations of spinlock and
mutex in snd_intelhad object were dropped mistakenly.
This patch adds the missing initializations again for each port.
Fixes: b4eb0d522fcb ("ALSA: x86: Split snd_intelhad into card and PCM specific structures")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The patch "ALSA: control: code refactoring for ELEM_READ/ELEM_WRITE
operations" introduced a potential for kernel memory corruption due
to an incorrect if statement allowing non-readable controls to fall
through and call the get function. For TLV controls a driver can omit
SNDRV_CTL_ELEM_ACCESS_READ to ensure that only the TLV get function
can be called. Instead the normal get() can be invoked unexpectedly
and as the driver expects that this will only be called for controls
<= 512 bytes, potentially try to copy >512 bytes into the 512 byte
return array, so corrupting kernel memory.
The problem is an attempt to refactor the snd_ctl_elem_read function
to invert the logic so that it conditionally aborted if the control
is unreadable instead of conditionally executing. But the if statement
wasn't inverted correctly.
The correct inversion of
if (a && !b)
is
if (!a || b)
Fixes: becf9e5d553c2 ("ALSA: control: code refactoring for ELEM_READ/ELEM_WRITE operations")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
into drm-fixes
- Powerplay fixes for cards with no displays attached
- Couple of DC fixes
- radeon workaround for PPC64
* 'drm-fixes-4.16' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: insist on 32-bit DMA for Cedar on PPC64/PPC64LE
drm/amd/display: VGA black screen from s3 when attached to hook
drm/amdgpu: Unify the dm resume calls into one
drm/amdgpu: Add a missing lock for drm_mm_takedown
Revert "drm/radeon/pm: autoswitch power state when in balanced mode"
drm/amd/powerplay/smu7: allow mclk switching with no displays
drm/amd/powerplay/vega10: allow mclk switching with no displays
|
|
The ARM PMU doesn't have a reg address, so fix the following DTC warning
(requires W=1):
Node /soc/arm-pmu missing or empty reg/ranges property
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This patch fixes the following DTC warning (requires W=1):
Node /soc/local_intc simple-bus unit address format error, expected "40000000"
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Jon attempted to fix the amount of RAM on the BCM958625HR in commit
c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
but it seems like we tripped over some poorly documented schematics.
The top-level page of the schematics says the board has 2GB, but when
you end-up scrolling to page 6, you see two chips of 4GBit (512MB) but
what the bootloader really initializes only 512MB, any attempt to use
more than that results in data aborts. Fix this again back to 512MB.
Fixes: c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
It seems that the proper value to return in this particular case is the
one contained into variable new_index instead of ret.
Addresses-Coverity-ID: 1465148 ("Copy-paste error")
Fixes: e46c7287b1c2 ("nbd: add a basic netlink interface")
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull seccomp fix from James Morris:
"This disables the seccomp samples when cross compiling.
We've seen too many build issues here, so it's best to just disable
it, especially since they're just the samples"
* 'fixes-v4.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
samples/seccomp: do not compile when cross compiled
|
|
The Cinterion PL8 is an LTE modem with 2 possible WWAN interfaces.
The modem is controlled via AT commands through the exposed TTYs.
AT^SWWAN write command can be used to activate or deactivate a WWAN
connection for a PDP context defined with AT+CGDCONT. UE supports
two WWAN adapter. Both WWAN adapters can be activated a the same time
Signed-off-by: Bassem Boubaker <bassem.boubaker@actia.fr>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tls ulp overrides sk->prot with a new tls specific proto structs.
The tls specific structs were previously based on the ipv4 specific
tcp_prot sturct.
As a result, attaching the tls ulp to an ipv6 tcp socket replaced
some ipv6 callback with the ipv4 equivalents.
This patch adds ipv6 tls proto structs and uses them when
attached to ipv6 sockets.
Fixes: 3c4d7559159b ('tls: kernel TLS support')
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have uninlined the sh_eth_{read|write}() functions introduced in the
commit 4a55530f38e ("net: sh_eth: modify the definitions of register").
Now remove *inline* from sh_eth_tsu_{read|write}() as well and move
these functions from the header to the driver itself. This saves 684
more bytes of object code (ARM gcc 4.8.5)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Xin Long says:
====================
net: fix IFLA_MTU ignored on NEWLINK for some ip and ipv6 tunnels
The fix for ip_gre follows the way other ip tunnels do: not to
set mtu in ndo_init, as ip_tunnel_newlink will take care of it
properly.
The fix for ip6_tunnel and sit follows the way ipv6 tunenls do:
to set mtu again according to IFLA_MTU after, as all bind_dev
are called in ndo_init where it can't get the tb[IFLA_MTU].
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 128bb975dc3c ("ip6_gre: init dev->mtu and dev->hard_header_len
correctly") fixed IFLA_MTU ignored on NEWLINK for ip6_gre. The same
mtu fix is also needed for sit.
Note that dev->hard_header_len setting for sit works fine, no need to
fix it. sit is actually ipv4 tunnel, it can't call ip6_tnl_change_mtu
to set mtu.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 128bb975dc3c ("ip6_gre: init dev->mtu and dev->hard_header_len
correctly") fixed IFLA_MTU ignored on NEWLINK for ip6_gre. The same
mtu fix is also needed for ip6_tunnel.
Note that dev->hard_header_len setting for ip6_tunnel works fine,
no need to fix it.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's safe to remove the setting of dev's needed_headroom and mtu in
__gre_tunnel_init, as discussed in [1], ip_tunnel_newlink can do it
properly.
Now Eric noticed that it could cover the mtu value set in do_setlink
when creating a ip_gre dev. It makes IFLA_MTU param not take effect.
So this patch is to remove them to make IFLA_MTU work, as in other
ipv4 tunnels.
[1]: https://patchwork.ozlabs.org/patch/823504/
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.")
Reported-by: Eric Garver <e@erig.me>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit f5e64032a799 ("net: phy: fix resume handling") changes the
locking semantics for phy_resume() such that the caller now needs to
hold the phy mutex. Not all call sites were adopted to this new
semantic, resulting in warnings from the added
WARN_ON(!mutex_is_locked(&phydev->lock)). Rather than change the
semantics, add a __phy_resume() and restore the old behavior of
phy_resume().
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: f5e64032a799 ("net: phy: fix resume handling")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/kees/linux into fixes-v4.16-rc4
- do not build samples when cross compiling (Michal Hocko)
From Kees: "This disables the seccomp samples when cross compiling. We're seen too many build issues here, so
it's best to just disable it, especially since they're just the samples."
|
|
Use the right loop index, not the number of devices in the array that we
need to remove, the following message uncovered the problem:
[ 5437.044119] hook not found, pf 5 num 0
[ 5437.044140] WARNING: CPU: 2 PID: 24983 at net/netfilter/core.c:376 __nf_unregister_net_hook+0x250/0x280
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Kernel crashed when run fio in a RAID5 backend bcache device, the call
trace is bellow:
[ 440.012034] kernel BUG at block/blk-ioc.c:146!
[ 440.012696] invalid opcode: 0000 [#1] SMP NOPTI
[ 440.026537] CPU: 2 PID: 2205 Comm: md127_raid5 Not tainted 4.15.0 #8
[ 440.027441] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 07/16
/2015
[ 440.028615] RIP: 0010:put_io_context+0x8b/0x90
[ 440.029246] RSP: 0018:ffffa8c882b43af8 EFLAGS: 00010246
[ 440.029990] RAX: 0000000000000000 RBX: ffffa8c88294fca0 RCX: 0000000000
0f4240
[ 440.031006] RDX: 0000000000000004 RSI: 0000000000000286 RDI: ffffa8c882
94fca0
[ 440.032030] RBP: ffffa8c882b43b10 R08: 0000000000000003 R09: ffff949cb8
0c1700
[ 440.033206] R10: 0000000000000104 R11: 000000000000b71c R12: 00000000000
01000
[ 440.034222] R13: 0000000000000000 R14: ffff949cad84db70 R15: ffff949cb11
bd1e0
[ 440.035239] FS: 0000000000000000(0000) GS:ffff949cba280000(0000) knlGS:
0000000000000000
[ 440.060190] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 440.084967] CR2: 00007ff0493ef000 CR3: 00000002f1e0a002 CR4: 00000000001
606e0
[ 440.110498] Call Trace:
[ 440.135443] bio_disassociate_task+0x1b/0x60
[ 440.160355] bio_free+0x1b/0x60
[ 440.184666] bio_put+0x23/0x30
[ 440.208272] search_free+0x23/0x40 [bcache]
[ 440.231448] cached_dev_write_complete+0x31/0x70 [bcache]
[ 440.254468] closure_put+0xb6/0xd0 [bcache]
[ 440.277087] request_endio+0x30/0x40 [bcache]
[ 440.298703] bio_endio+0xa1/0x120
[ 440.319644] handle_stripe+0x418/0x2270 [raid456]
[ 440.340614] ? load_balance+0x17b/0x9c0
[ 440.360506] handle_active_stripes.isra.58+0x387/0x5a0 [raid456]
[ 440.380675] ? __release_stripe+0x15/0x20 [raid456]
[ 440.400132] raid5d+0x3ed/0x5d0 [raid456]
[ 440.419193] ? schedule+0x36/0x80
[ 440.437932] ? schedule_timeout+0x1d2/0x2f0
[ 440.456136] md_thread+0x122/0x150
[ 440.473687] ? wait_woken+0x80/0x80
[ 440.491411] kthread+0x102/0x140
[ 440.508636] ? find_pers+0x70/0x70
[ 440.524927] ? kthread_associate_blkcg+0xa0/0xa0
[ 440.541791] ret_from_fork+0x35/0x40
[ 440.558020] Code: c2 48 00 5b 41 5c 41 5d 5d c3 48 89 c6 4c 89 e7 e8 bb c2
48 00 48 8b 3d bc 36 4b 01 48 89 de e8 7c f7 e0 ff 5b 41 5c 41 5d 5d c3 <0f> 0b
0f 1f 00 0f 1f 44 00 00 55 48 8d 47 b8 48 89 e5 41 57 41
[ 440.610020] RIP: put_io_context+0x8b/0x90 RSP: ffffa8c882b43af8
[ 440.628575] ---[ end trace a1fd79d85643a73e ]--
All the crash issue happened when a bypass IO coming, in such scenario
s->iop.bio is pointed to the s->orig_bio. In search_free(), it finishes the
s->orig_bio by calling bio_complete(), and after that, s->iop.bio became
invalid, then kernel would crash when calling bio_put(). Maybe its upper
layer's faulty, since bio should not be freed before we calling bio_put(),
but we'd better calling bio_put() first before calling bio_complete() to
notify upper layer ending this bio.
This patch moves bio_complete() under bio_put() to avoid kernel crash.
[mlyle: fixed commit subject for character limits]
Reported-by: Matthias Ferdinand <bcache@mfedv.net>
Tested-by: Matthias Ferdinand <bcache@mfedv.net>
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit 2831231d4c3f ("bcache: reduce cache_set devices iteration by
devices_max_used") adds c->devices_max_used to reduce iteration of
c->uuids elements, this value is updated in bcache_device_attach().
But for flash only volume, when calling flash_devs_run(), the function
bcache_device_attach() is not called yet and c->devices_max_used is not
updated. The unexpected result is, the flash only volume won't be run
by flash_devs_run().
This patch fixes the issue by iterate all c->uuids elements in
flash_devs_run(). c->devices_max_used will be updated properly when
bcache_device_attach() gets called.
[mlyle: commit subject edited for character limit]
Fixes: 2831231d4c3f ("bcache: reduce cache_set devices iteration by devices_max_used")
Reported-by: Tang Junhui <tang.junhui@zte.com.cn>
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull tpm fixes from James Morris:
"Bugfixes for TPM, from Jeremy Boone, via Jarkko Sakkinen"
* 'fixes-v4.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm: fix potential buffer overruns caused by bit glitches on the bus
tpm: st33zp24: fix potential buffer overruns caused by bit glitches on the bus
tpm_i2c_infineon: fix potential buffer overruns caused by bit glitches on the bus
tpm_i2c_nuvoton: fix potential buffer overruns caused by bit glitches on the bus
tpm_tis: fix potential buffer overruns caused by bit glitches on the bus
|
|
In commit 60c253069632 ("tipc: fix race between poll() and
setsockopt()") we introduced a pointer from struct tipc_group to the
'group_is_connected' flag in struct tipc_sock, so that this field can
be checked without dereferencing the group pointer of the latter struct.
The initial value for this flag is correctly set to 'false' when a
group is created, but we miss the case when no group is created at
all, in which case the initial value should be 'true'. This has the
effect that SOCK_RDM/DGRAM sockets sending datagrams never receive
POLLOUT if they request so.
This commit corrects this bug.
Fixes: 60c253069632 ("tipc: fix race between poll() and setsockopt()")
Reported-by: Hoang Le <hoang.h.le@dektek.com.au>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit a307a1e6bc0d "cpufreq: s3c: use cpufreq_generic_init()"
accidentally broke cpufreq on s3c2410 and s3c2412.
These two platforms don't have a CPU frequency table and used to skip
calling cpufreq_table_validate_and_show() for them. But with the
above commit, we started calling it unconditionally and that will
eventually fail as the frequency table pointer is NULL.
Fix this by calling cpufreq_table_validate_and_show() conditionally
again.
Fixes: a307a1e6bc0d "cpufreq: s3c: use cpufreq_generic_init()"
Cc: 3.13+ <stable@vger.kernel.org> # v3.13+
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix resource coverity errors.
Fixes: d9f9b9a4d05f ("devlink: Add support for resource abstraction")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to RFC 1191 sections 3 and 4, ICMP frag-needed messages
indicating an MTU below 68 should be rejected:
A host MUST never reduce its estimate of the Path MTU below 68
octets.
and (talking about ICMP frag-needed's Next-Hop MTU field):
This field will never contain a value less than 68, since every
router "must be able to forward a datagram of 68 octets without
fragmentation".
Furthermore, by letting net.ipv4.route.min_pmtu be set to negative
values, we can end up with a very large PMTU when (-1) is cast into u32.
Let's also make ip_rt_min_pmtu a u32, since it's only ever compared to
unsigned ints.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
pull request: bluetooth 2018-02-26
Here are a two Bluetooth driver fixes for the 4.16 kernel.
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current implementation checks the combined size of the children with
the 'size' of the parent. The correct behavior is to check the combined
size vs the pending change and to compare vs the 'size_new'.
Fixes: d9f9b9a4d05f ("devlink: Add support for resource abstraction")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Tested-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to R-Car Gen3 Rev.0.80 manual, the DMATCR can be set to
16,777,215 as maximum. So, this patch fixes the max_chunk_size for
safety on all of SoCs. Otherwise, a system may hang if the DMATCR
is set to 0 on R-Car Gen3.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
As the block layer, since the conversion to blkmq, claims the host using a
context, a following nested call to mmc_claim_host(), which isn't using a
context, may hang.
Calling mmc_interrupt_hpi() and mmc_read_bkops_status() via the mmc block
layer, may suffer from this problem, as these functions are calling
mmc_claim|release_host().
Let's fix the problem by removing the calls to mmc_claim|release_host()
from the above mentioned functions and instead make the callers responsible
of claiming/releasing the host. As a matter of fact, the existing callers
already deals with it.
Fixes: 81196976ed94 ("mmc: block: Add blk-mq support")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
|
|
cat /sys/kernel/debug/mmc0/regs will hang up the system since
it's in runtime suspended state, so the genpd and biu_clk is
off. This patch fixes this problem by calling pm_runtime_get_sync
to wake it up before reading the registers.
Fixes: e9ed8835e990 ("mmc: dw_mmc: add runtime PM callback")
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add num_caps field for dw_mci_drv_data to validate the controller
id from DT alias and non-DT ways.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 800d78bfccb3 ("mmc: dw_mmc: add support for implementation specific callbacks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Factor out dw_mci_init_slot_caps to consolidate parsing
all differents types of capabilities from host contrllers.
No functional change intended.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 800d78bfccb3 ("mmc: dw_mmc: add support for implementation specific callbacks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The hs_timing_cfg[] array is indexed using a value derived from the
"mshcN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: 361c7fe9b02eee7e ("mmc: dw_mmc-k3: add sd support for hi3660")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
New options introduced by the patch this fixes are still
enabled even if CFG80211 is disabled.
.config:
# CONFIG_CFG80211 is not set
CONFIG_CFG80211_REQUIRE_SIGNED_REGDB=y
CONFIG_CFG80211_USE_KERNEL_REGDB_KEYS=y
# CONFIG_LIB80211 is not set
When CFG80211_REQUIRE_SIGNED_REGDB is enabled, it selects
SYSTEM_DATA_VERIFICATION which selects SYSTEM_TRUSTED_KEYRING
that need extract-cert tool. extract-cert needs some openssl
headers to be installed on the build machine.
Instead of adding missing "depends on CFG80211", it's
easier to use a 'if' block around all options related
to CFG80211, so do that.
Fixes: 90a53e4432b1 ("cfg80211: implement regdb signature checking")
Signed-off-by: Romain Naour <romain.naour@gmail.com>
[touch up commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
wake_klogd is a local variable in console_unlock(). The information
is lost when the console_lock owner using the busy wait added by
the commit dbdda842fe96f8932 ("printk: Add console owner and waiter
logic to load balance console writes"). The following race is
possible:
CPU0 CPU1
console_unlock()
for (;;)
/* calling console for last message */
printk()
log_store()
log_next_seq++;
/* see new message */
if (seen_seq != log_next_seq) {
wake_klogd = true;
seen_seq = log_next_seq;
}
console_lock_spinning_enable();
if (console_trylock_spinning())
/* spinning */
if (console_lock_spinning_disable_and_check()) {
printk_safe_exit_irqrestore(flags);
return;
console_unlock()
if (seen_seq != log_next_seq) {
/* already seen */
/* nothing to do */
Result: Nobody would wakeup klogd.
One solution would be to make a global variable from wake_klogd.
But then we would need to manipulate it under a lock or so.
This patch wakes klogd also when console_lock is passed to the
spinning waiter. It looks like the right way to go. Also userspace
should have a chance to see and store any "flood" of messages.
Note that the very late klogd wake up was a historic solution.
It made sense on single CPU systems or when sys_syslog() operations
were synchronized using the big kernel lock like in v2.1.113.
But it is questionable these days.
Fixes: dbdda842fe96f8932 ("printk: Add console owner and waiter logic to load balance console writes")
Link: http://lkml.kernel.org/r/20180226155734.dzwg3aovqnwtvkoy@pathway.suse.cz
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-kernel@vger.kernel.org
Cc: Tejun Heo <tj@kernel.org>
Suggested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
|
|
Tuning can leave the IP in an active state (Buffer Read Enable bit set)
which prevents the entry to low power states (i.e. S0i3). Data reset will
clear it.
Generally tuning is followed by a data transfer which will anyway sort out
the state, so it is rare that S0i3 is actually prevented.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
