| Age | Commit message (Collapse) | Author |
|---|
|
Newly-allocated skbs default to PACKET_HOST, and eth_type_trans() is
smart enough to determine any other packet type from the frame's
destination address.
So except for the IQD sniffer case, there is no need to set up
skb->pkt_type manually.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
napi_alloc_skb() doesn't need to disable IRQs during the allocation,
and thus may save us a few cycles.
Doing so requires a small fix-up in the HiperTransport path, which
currently assumes a fixed NET_SKB_PAD headroom padding. napi_alloc_skb()
adds an additional NET_IP_ALIGN padding, so use the proper helper for
setting up the mac_header offset.
Use this opportunity to convert the non-NAPI path to netdev_alloc_skb(),
which means that skb->dev is now always set-up during allocation and
doesn't need to be assigned manually.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to pass the *payload* length, not the L2 address length.
For qeth (using eth_header()) this is merely a cosmetic change:
the parameter only matters when building headers for ETH_P_802_2
or ETH_P_802_3, whereas our fake headers are built with
ETH_P_IP / ETH_P_IPV6 / 0.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qeth implements HW-based Unicast Filtering (via SETVMAC) on L2 devices.
Tell the stack, so it knows that receiving traffic for secondary
addresses doesn't require full-blown promiscuous mode.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NETIF_F_SG support is currently limited to OSA (and for L2 even OSD)
devices. Advertise it for some more device types (OSM, L2 OSX, z/VM OSA)
that share the same code paths. For now, keep it switched off by
default on these devices.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'portname' attribute is deprecated and setting it has no effect.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"s390/qeth: fix SETIP command handling" introduced a new helper, apply
it driver-wide.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
William Tu says:
====================
a couple of erspan fixes
The series fixes a couple of erspan issues.
The first patch adds the erspan v2 proto type to the ip6 tunnel lookup.
The second patch improves the error handling when users screws the
version number in metadata. The final patch makes sure the skb has
enough headroom for pushing erspan header when xmit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch adds skb_cow_header() to ensure enough headroom
at ip6erspan_tunnel_xmit before pushing the erspan header
to the skb.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When users fill in incorrect erspan version number through
the struct erspan_metadata uapi, current code skips pushing
the erspan header but continue pushing the gre header, which
is incorrect. The patch fixes it by returning error.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch adds the erspan v2 proto in ip6gre_tunnel_lookup
so the erspan v2 tunnel can be found correctly.
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ido Schimmel says:
====================
mlxsw: ACL and mirroring fixes
The first patch fixes offload of rules using the 'pass' action. Instead
of continuing to evaluate lower priority rules, the binding is
terminated and the packet proceeds to the bridge and router blocks on
ingress, or goes out of the port on egress.
Second patch prevents the user from mirroring more than once from a
given {Port, Direction} as this is not supported by the device.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Spectrum ASIC doesn't support mirroring more than once from a single
binding point (which is a port-direction pair). Therefore detect that a
second binding of a given binding point is attempted.
To that end, extend struct mlxsw_sp_span_inspected_port to track whether
a given binding point is bound or not. Extend
mlxsw_sp_span_entry_port_find() to look for ports based on the full
unique key: port number, direction, and boundness.
Besides fixing the overt bug where configured mirrors are not offloaded,
this also fixes a more subtle bug: mlxsw_sp_span_inspected_port_del()
just defers to mlxsw_sp_span_entry_bound_port_find(), and that used to
find the first port with the right number (disregarding the type). Thus
by adding and removing egress and ingress mirrors in the right order,
one could trick the system into believing it has no egress mirrors when
in fact it did have some. That then caused that
mlxsw_sp_span_port_mtu_update() didn't update mirroring buffer when MTU
was changed.
Fixes: 763b4b70afcd ("mlxsw: spectrum: Add support in matchall mirror TC offloading")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For ok GACT action, TERMINATE binding_cmd should be used in action set
passed down to HW.
Fixes: b2925957ec1a9 ("mlxsw: spectrum_flower: Offload "ok" termination action")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Two type of fixes:
- The usual stuff, a handful HD-audio quirks for various machines
- Further hardening against ALSA sequencer ioctl/write races that are
triggered by fuzzer"
* tag 'sound-4.16-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda: add dock and led support for HP ProBook 640 G2
ALSA: hda: add dock and led support for HP EliteBook 820 G3
ALSA: hda/realtek - Make dock sound work on ThinkPad L570
ALSA: seq: Remove superfluous snd_seq_queue_client_leave_cells() call
ALSA: seq: More protection for concurrent write and ioctl races
ALSA: seq: Don't allow resizing pool in use
ALSA: hda/realtek - Fix dock line-out volume on Dell Precision 7520
ALSA: hda/realtek: Limit mic boost on T480
ALSA: hda/realtek - Add headset mode support for Dell laptop
ALSA: hda/realtek - Add support headset mode for DELL WYSE
ALSA: hda - Fix a wrong FIXUP for alc289 on Dell machines
|
|
Currently the driver attempts to spin lock on udc->lock before a NULL
pointer check is performed on udc, hence there is a potential null
pointer dereference on udc->lock. Fix this by moving the null check
on udc before the lock occurs.
Fixes: ea6873a45a22 ("usbip: vudc: Add SysFS infrastructure for VUDC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some network devices - notably ipvlan slave - are not compatible with
any kind of rx_handler. Currently the hook can be installed but any
configuration (bridge, bond, macsec, ...) is nonfunctional.
This change allocates a priv_flag bit to mark such devices and explicitly
forbid installing a rx_handler if such bit is set. The new bit is used
by ipvlan slave device.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
T6 cards can support up to 100 G speeds. So, increase
max programmable tx rate limit to 100 Gbps.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A recent update to the ARM SMCCC ARCH_WORKAROUND_1 specification
allows firmware to return a non zero, positive value to describe
that although the mitigation is implemented at the higher exception
level, the CPU on which the call is made is not affected.
Let's relax the check on the return value from ARCH_WORKAROUND_1
so that we only error out if the returned value is negative.
Fixes: b092201e0020 ("arm64: Add ARM_SMCCC_ARCH_WORKAROUND_1 BP hardening support")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Sphinx 1.7 removed sphinx.util.compat.Directive so people
who have upgraded cannot build the documentation. Switch to
docutils.parsers.rst.Directive which has been available since
docutils 0.5 released in 2009.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=1083694
Co-developed-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
"This fixes a corner case for NFS exporting (introduced in this cycle)
as well as fixing miscellaneous bugs"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: update Kconfig texts
ovl: redirect_dir=nofollow should not follow redirect for opaque lower
ovl: fix ptr_ret.cocci warnings
ovl: check ERR_PTR() return value from ovl_lookup_real()
ovl: check lower ancestry on encode of lower dir file handle
ovl: hash non-dir by lower inode for fsnotify
|
|
Pull xfs fixes from Darrick Wong:
- Fix some iomap locking problems
- Don't allocate cow blocks when we're zeroing file data
* tag 'xfs-4.16-fixes-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: don't block on the ilock for RWF_NOWAIT
xfs: don't start out with the exclusive ilock for direct I/O
xfs: don't allocate COW blocks for zeroing holes or unwritten extents
|
|
When the DELL_SMBIOS_SMM backend is enabled, the DELL_SMBIOS symbol
depends on DELL_DCDBAS, and we must avoid the situation where
DELL_SMBIOS=y and DCDBAS=m.
Adding the conditional dependency to DELL_SMBIOS such as:
depends !DELL_SMBIOS_SMM || (DCDBAS || DCDBAS=n)
results in the Kconfig tooling complaining about a circular dependency,
although it appears to work in practice.
Avoid the errors by simplifying the dependency and forcing DELL_SMBIOS
to be <= DCDBAS if DCDBAS is enabled (thanks to Greg KH for the
suggestion).
Cc: Mario.Limonciello@dell.com
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
Avoid accidental configurations by setting default y for DELL_SMBIOS
backends. Avoid this impacting the default build size, by making them
dependent on DELL_SMBIOS, so they only appear when DELL_SMBIOS is
manually selected, or by DELL_LAPTOP or DELL_WMI.
While DELL_SMBIOS does have a prompt, it does not have any dependencies.
Keeping DELL_SMBIOS visible, despite being "select"ed by DELL_LAPTOP and
DELL_WMI, is a deliberate choice to provide context for the WMI and SMM
backends, which would otherwise appear to float without context within
the menu.
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
Some race conditions were raised due to dell-smbios and its backends
not being ready by the time that a consumer would call one of the
exported methods.
To avoid this problem, guarantee that all initialization has been
done by linking them all together and running init for them all.
As part of this change the Kconfig needs to be adjusted so that
CONFIG_DELL_SMBIOS_SMM and CONFIG_DELL_SMBIOS_WMI are boolean
rather than modules.
CONFIG_DELL_SMBIOS is a visually selectable option again and both
CONFIG_DELL_SMBIOS_WMI and CONFIG_DELL_SMBIOS_SMM are optional.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
[dvhart: Update prompt and help text for DELL_SMBIOS_* backends]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
This is being done to faciliate a later change to link all the dell-smbios
drivers together.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
WARNING: function definition argument 'struct calling_interface_buffer *'
should also have an identifier name
+ int (*call_fn)(struct calling_interface_buffer *);
WARNING: Block comments use * on subsequent lines
+ /* 4 bytes of table header, plus 7 bytes of Dell header,
plus at least
+ 6 bytes of entry */
WARNING: Block comments use a trailing */ on a separate line
+ 6 bytes of entry */
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One notable fix to properly advertise our support for a new firmware
feature, caused by two series conflicting semantically but not
textually.
There's a new ioctl for the new ocxl driver, which is not a fix, but
needed to complete the userspace API and good to have before the
driver is in a released kernel.
Finally three minor selftest fixes, and a fix for intermittent build
failures for some obscure platforms, caused by a missing make
dependency.
Thanks to: Alastair D'Silva, Bharata B Rao, Guenter Roeck"
* tag 'powerpc-4.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: Fix vector5 in ibm architecture vector table
ocxl: Document the OCXL_IOCTL_GET_METADATA IOCTL
ocxl: Add get_metadata IOCTL to share OCXL information to userspace
selftests/powerpc: Skip the subpage_prot tests if the syscall is unavailable
selftests/powerpc: Fix missing clean of pmu/lib.o
powerpc/boot: Fix random libfdt related build errors
selftests/powerpc: Skip tm-trap if transactional memory is not enabled
|
|
When a USB device gets plugged on ASUS PRIME B350M-A's front ports, the
xHC stops working:
[ 549.114587] xhci_hcd 0000:02:00.0: WARN: xHC CMD_RUN timeout
[ 549.114608] suspend_common(): xhci_pci_suspend+0x0/0xc0 returns -110
[ 549.114638] xhci_hcd 0000:02:00.0: can't suspend (hcd_pci_runtime_suspend returned -110)
Delay before running xHC command CMD_RUN can workaround the issue.
Use a new quirk to make the delay only targets to the affected xHC.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch reverts the commit 835e4241e714 ("usb: host: xhci-plat:
enable clk in resume timing") because this driver also has runtime PM
and the commit 560869100b99 ("clk: renesas: cpg-mssr: Restore module
clocks during resume") will restore the clock on R-Car H3 environment.
If the xhci_plat_suspend() disables the clk, the system cannot enable
the clk in resume like the following behavior:
< In resume >
- genpd_resume_noirq() runs and enable the clk (enable_count = 1)
- cpg_mssr_resume_noirq() restores the clk register.
-- Since the clk was disabled in suspend, cpg_mssr_resume_noirq()
will disable the clk and keep the enable_count.
- Even if xhci_plat_resume() calls clk_prepare_enable(), since
the enable_count is 1, the clk will be not enabled.
After this patch is applied, the cpg-mssr driver will save the clk
as enable, so the clk will be enabled in resume.
Fixes: 835e4241e714 ("usb: host: xhci-plat: enable clk in resume timing")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Jason Wang says:
====================
Several fixes for vhost_net ptr_ring usage
This small series try to fix several bugs of ptr_ring usage in
vhost_net. Please review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit fc72d1d54dd9 ("tuntap: XDP transmission"), we can
actually queueing XDP pointers in the pointer ring, so we should
examine the pointer type before freeing the pointer.
Fixes: fc72d1d54dd9 ("tuntap: XDP transmission")
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We get pointer ring from the exported sock, this means we should keep
rx_ring and vq->private synced during both vq stop and backend set,
otherwise we may see stale rx_ring.
Fixes: c67df11f6e480 ("vhost_net: try batch dequing from skb array")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KMSAN reported a use of uninit memory in vhost_net_buf_unproduce()
while trying to access n->vqs[VHOST_NET_VQ_TX].rx_ring:
==================================================================
BUG: KMSAN: use of uninitialized memory in vhost_net_buf_unproduce+0x7bb/0x9a0 drivers/vho
et.c:170
CPU: 0 PID: 3021 Comm: syz-fuzzer Not tainted 4.16.0-rc4+ #3853
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x185/0x1d0 lib/dump_stack.c:53
kmsan_report+0x142/0x1f0 mm/kmsan/kmsan.c:1093
__msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:676
vhost_net_buf_unproduce+0x7bb/0x9a0 drivers/vhost/net.c:170
vhost_net_stop_vq drivers/vhost/net.c:974 [inline]
vhost_net_stop+0x146/0x380 drivers/vhost/net.c:982
vhost_net_release+0xb1/0x4f0 drivers/vhost/net.c:1015
__fput+0x49f/0xa00 fs/file_table.c:209
____fput+0x37/0x40 fs/file_table.c:243
task_work_run+0x243/0x2c0 kernel/task_work.c:113
tracehook_notify_resume include/linux/tracehook.h:191 [inline]
exit_to_usermode_loop arch/x86/entry/common.c:166 [inline]
prepare_exit_to_usermode+0x349/0x3b0 arch/x86/entry/common.c:196
syscall_return_slowpath+0xf3/0x6d0 arch/x86/entry/common.c:265
do_syscall_64+0x34d/0x450 arch/x86/entry/common.c:292
...
origin:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:303 [inline]
kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:213
kmsan_kmalloc_large+0x6f/0xd0 mm/kmsan/kmsan.c:392
kmalloc_large_node_hook mm/slub.c:1366 [inline]
kmalloc_large_node mm/slub.c:3808 [inline]
__kmalloc_node+0x100e/0x1290 mm/slub.c:3818
kmalloc_node include/linux/slab.h:554 [inline]
kvmalloc_node+0x1a5/0x2e0 mm/util.c:419
kvmalloc include/linux/mm.h:541 [inline]
vhost_net_open+0x64/0x5f0 drivers/vhost/net.c:921
misc_open+0x7b5/0x8b0 drivers/char/misc.c:154
chrdev_open+0xc28/0xd90 fs/char_dev.c:417
do_dentry_open+0xccb/0x1430 fs/open.c:752
vfs_open+0x272/0x2e0 fs/open.c:866
do_last fs/namei.c:3378 [inline]
path_openat+0x49ad/0x6580 fs/namei.c:3519
do_filp_open+0x267/0x640 fs/namei.c:3553
do_sys_open+0x6ad/0x9c0 fs/open.c:1059
SYSC_openat+0xc7/0xe0 fs/open.c:1086
SyS_openat+0x63/0x90 fs/open.c:1080
do_syscall_64+0x2f1/0x450 arch/x86/entry/common.c:287
==================================================================
Fixes: c67df11f6e480 ("vhost_net: try batch dequing from skb array")
Signed-off-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This enables AVE_GI_RXDROP interrupt factor. This factor indicates
depletion of Rx descriptors and the handler counts the number
of dropped packets.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enabling -Wvla, remove VLA usage and replace it
with a fixed-length array instead.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As well as the basic conversion, I noticed that a lot of the
SCTP code checks gso_type without first checking skb_is_gso()
so I have added that where appropriate.
Also, document the helper.
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixed a coding style issue.
Signed-off-by: Vaibhav Murkute <vaibhavmurkute88@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Peng Li says:
====================
fixes for configuration lost problems
This patchset refactors some functions and some bugs in order
to fix the configuration loss problem when resetting and
setting channel number.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the coalesce configuation lost problem when
setting the channel number by restoring all vectors's coalesce
configuation to vector 0's, because all vectors belonging to
the same netdev have the same coalesce configuation for now.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch refoctors the coalesce related struct by introducing
the hns3_enet_coalesce struct, in order to fix the coalesce
configuation lost problem when changing the channel number.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Coalesce configuration will be set to default value by
hns3_nic_init_vector_data during reset, which causes the
coalesce configuration loss problem.
This patch fixes it by setting the default value in
hns3_nic_alloc_vector_data, which will not be called in the
reset process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a get_vector function, which allocate the vectors
for a client, but there is not a put_vector to free the
vector.
This patch introduces the put_vector function in order to
fix the coalesce configuration lost problem during reset
process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In hns3_set_ringparam, hns3_uninit_all_ring frees the
memory pointed by priv->ring_data[i].ring, and
hns3_change_all_ring_bd_num use that pointer without mallocing,
which will cause a use-after-free problem.
The patch fixes it by not freeing the memory in
hns3_uninit_all_ring, and uses hns3_put_ring_config to free it
when necessary.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pause configuration will be set to default value by hclge_tm_schd_init
during reset, which causes the RSS configuration loss problem.
This patch fixes it by calling hclge_tm_init_hw during reset process
, which will set the pause configuration to default value.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RSS configuration will be set to default value by hclge_rss_init_hw
during reset, which causes the RSS configuration loss problem.
This patch fixes it by setting the default value in
hclge_rss_init_cfg function, which will not be called in the reset
process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch refactors the hclge_get/set_rss_tuple function
in order to fix the rss configuration loss problem during
reset process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch refactors the hclge_get/set_rss function in
order to fix the rss configuration loss problem during
reset process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Roman Mashak says:
====================
Fix event generation for actions batch Add/Delete mode
When adding or deleting a batch of entries, the kernel sends upto
TCA_ACT_MAX_PRIO entries in an event to user space. However it does not
consider that the action sizes may vary and require different skb sizes.
For example :
% cat tc-batch.sh
TC="sudo /mnt/iproute2.git/tc/tc"
$TC actions flush action gact
for i in `seq 1 $1`;
do
cmd="action pass index $i "
args=$args$cmd
done
$TC actions add $args
%
% ./tc-batch.sh 32
Error: Failed to fill netlink attributes while adding TC action.
We have an error talking to the kernel
%
This patchset introduces new callback in tc_action_ops, which calculates
the action size, and passes size to tcf_add_notify()/tcf_del_notify(). The
patch fixes act_gact, and the rest of actions will be updated in the
follow-up patches.
v3:
Fixed tcf_action_fill_size() to return shared attrs length when
action ->get_fill_size() isn't implemented.
v2:
Restructured patches to make them bisectable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
