| Age | Commit message (Collapse) | Author |
|---|
|
Guillaume Nault says:
====================
gre: Fix regressions in IPv6 link-local address generation.
IPv6 link-local address generation has some special cases for GRE
devices. This has led to several regressions in the past, and some of
them are still not fixed. This series fixes the remaining problems,
like the ipv6.conf.<dev>.addr_gen_mode sysctl being ignored and the
router discovery process not being started (see details in patch 1).
To avoid any further regressions, patch 2 adds selftests covering
IPv4 and IPv6 gre/gretap devices with all combinations of currently
supported addr_gen_mode values.
====================
Link: https://patch.msgid.link/cover.1741375285.git.gnault@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
GRE devices have their special code for IPv6 link-local address
generation that has been the source of several regressions in the past.
Add selftest to check that all gre, ip6gre, gretap and ip6gretap get an
IPv6 link-link local address in accordance with the
net.ipv6.conf.<dev>.addr_gen_mode sysctl.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://patch.msgid.link/2d6772af8e1da9016b2180ec3f8d9ee99f470c77.1741375285.git.gnault@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use addrconf_addr_gen() to generate IPv6 link-local addresses on GRE
devices in most cases and fall back to using add_v4_addrs() only in
case the GRE configuration is incompatible with addrconf_addr_gen().
GRE used to use addrconf_addr_gen() until commit e5dd729460ca
("ip/ip6_gre: use the same logic as SIT interfaces when computing v6LL
address") restricted this use to gretap and ip6gretap devices, and
created add_v4_addrs() (borrowed from SIT) for non-Ethernet GRE ones.
The original problem came when commit 9af28511be10 ("addrconf: refuse
isatap eui64 for INADDR_ANY") made __ipv6_isatap_ifid() fail when its
addr parameter was 0. The commit says that this would create an invalid
address, however, I couldn't find any RFC saying that the generated
interface identifier would be wrong. Anyway, since gre over IPv4
devices pass their local tunnel address to __ipv6_isatap_ifid(), that
commit broke their IPv6 link-local address generation when the local
address was unspecified.
Then commit e5dd729460ca ("ip/ip6_gre: use the same logic as SIT
interfaces when computing v6LL address") tried to fix that case by
defining add_v4_addrs() and calling it to generate the IPv6 link-local
address instead of using addrconf_addr_gen() (apart for gretap and
ip6gretap devices, which would still use the regular
addrconf_addr_gen(), since they have a MAC address).
That broke several use cases because add_v4_addrs() isn't properly
integrated into the rest of IPv6 Neighbor Discovery code. Several of
these shortcomings have been fixed over time, but add_v4_addrs()
remains broken on several aspects. In particular, it doesn't send any
Router Sollicitations, so the SLAAC process doesn't start until the
interface receives a Router Advertisement. Also, add_v4_addrs() mostly
ignores the address generation mode of the interface
(/proc/sys/net/ipv6/conf/*/addr_gen_mode), thus breaking the
IN6_ADDR_GEN_MODE_RANDOM and IN6_ADDR_GEN_MODE_STABLE_PRIVACY cases.
Fix the situation by using add_v4_addrs() only in the specific scenario
where the normal method would fail. That is, for interfaces that have
all of the following characteristics:
* run over IPv4,
* transport IP packets directly, not Ethernet (that is, not gretap
interfaces),
* tunnel endpoint is INADDR_ANY (that is, 0),
* device address generation mode is EUI64.
In all other cases, revert back to the regular addrconf_addr_gen().
Also, remove the special case for ip6gre interfaces in add_v4_addrs(),
since ip6gre devices now always use addrconf_addr_gen() instead.
Fixes: e5dd729460ca ("ip/ip6_gre: use the same logic as SIT interfaces when computing v6LL address")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/559c32ce5c9976b269e6337ac9abb6a96abe5096.1741375285.git.gnault@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add unit tests for the PRP duplicate detection
Signed-off-by: Jaakko Karrenpalo <jkarrenpalo@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250307161700.1045-2-jkarrenpalo@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add PRP specific function for handling duplicate
packets. This is needed because of potential
L2 802.1p prioritization done by network switches.
The L2 prioritization can re-order the PRP packets
from a node causing the existing implementation to
discard the frame(s) that have been received 'late'
because the sequence number is before the previous
received packet. This can happen if the node is
sending multiple frames back-to-back with different
priority.
Signed-off-by: Jaakko Karrenpalo <jkarrenpalo@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250307161700.1045-1-jkarrenpalo@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There is an incorrect calculation in the offset variable which causes
the nft_skb_copy_to_reg() function to always return -EFAULT. Adding the
start variable is redundant. In the __ip_options_compile() function the
correct offset is specified when finding the function. There is no need
to add the size of the iphdr structure to the offset.
Fixes: dbb5281a1f84 ("netfilter: nf_tables: add support for matching IPv4 options")
Signed-off-by: Alexey Kashavkin <akashavkin@gmail.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch fixes a few typos, spelling mistakes, and a bit of grammar,
increasing the comments readability.
Signed-off-by: Janik Haag <janik@aq0.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250307145648.1679912-2-janik@aq0.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use string choices helper for better readability.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250307113733.819448-1-shaojijie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
With the blamed commit it seems that lan966x doesn't seem to boot
anymore when the internal CPU is used.
The reason seems to be the usage of the devm_of_iomap, if we replace
this with devm_ioremap, this seems to fix the issue as we use the same
region also for other devices.
Fixes: 0426a920d6269c ("reset: mchp: sparx5: Map cpu-syscon locally in case of LAN966x")
Reviewed-by: Herve Codina <herve.codina@bootlin.com>
Tested-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20250227105502.25125-1-horatiu.vultur@microchip.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
We use a notifier to implement the mechanism of informing the user-space
about changes in GPIO line status. We register with the notifier when
the GPIO character device file is opened and unregister when the last
reference to the associated file descriptor is dropped.
Since commit fcc8b637c542 ("gpiolib: switch the line state notifier to
atomic") we use the atomic notifier variant. Atomic notifiers call
rcu_synchronize in atomic_notifier_chain_unregister() which caused a
significant performance regression in some circumstances, observed by
user-space when calling close() on the GPIO device file descriptor.
Replace the atomic notifier with the raw variant and provide
synchronization with a read-write spinlock.
Fixes: fcc8b637c542 ("gpiolib: switch the line state notifier to atomic")
Reported-by: David Jander <david@protonic.nl>
Closes: https://lore.kernel.org/all/20250311110034.53959031@erd003.prtnl/
Tested-by: David Jander <david@protonic.nl>
Tested-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20250311-gpiolib-line-state-raw-notifier-v2-1-138374581e1e@linaro.org
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
During chip registration we should neither check the return value of
gc->get_direction() nor hold the SRCU lock when calling it. The former
is because pin controllers may have pins set to alternate functions and
return errors from their get_direction() callbacks. That's alright - we
should default to the safe INPUT state and not bail-out. The latter is
not needed because we haven't registered the chip yet so there's nothing
to protect against dynamic removal. In fact: we currently hit a lockdep
splat. Revert to calling the gc->get_direction() callback directly and
*not* checking its value.
Fixes: 9d846b1aebbe ("gpiolib: check the return value of gpio_chip::get_direction()")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Closes: https://lore.kernel.org/all/81f890fc-6688-42f0-9756-567efc8bb97a@samsung.com/
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20250226-retval-fixes-v2-1-c8dc57182441@linaro.org
Tested-by: Gene C <arch@sapience.com>
Link: https://lore.kernel.org/r/20250311175631.83779-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.14
The bulk of this is driver specific fixes, mostly unremarkable. There's
also one core fix from Charles, fixing up confusion around the limiting
of maximum control values.
|
|
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
|
|
When a character array without a terminating NUL character has a static
initializer, GCC 15's -Wunterminated-string-initialization will only
warn if the array lacks the "nonstring" attribute[1]. Mark the arrays
with __nonstring to and correctly identify the char array as "not a C
string" and thereby eliminate the warning.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=117178 [1]
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250310222257.work.866-kees@kernel.org
|
|
RTL8814A is a wifi 5 chip with 4 RF paths (chains), 3 spatial streams,
and probably no Bluetooth.
The USB-based RTL8814AU can reach 800 Mbps in the 5 GHz band in USB 3
mode. In USB 2 mode it only uses 2 spatial streams.
The PCI-based RTL8814AE is not as popular and didn't get as much
testing so it's unclear how fast it goes. It's more like a bonus on top
of the RTL8814AU support.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/5795b0a7-511e-40b5-ac36-476b63f174c7@gmail.com
|
|
This is the entry point for the new module rtw88_8814au.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/71457787-5a9e-4ead-a62c-22ca44e00b89@gmail.com
|
|
This is the entry point for the new module rtw88_8814ae.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/74ebab2f-a23e-4d87-935f-0af2b5cba672@gmail.com
|
|
These contain all the logic for the RTL8814A chip.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/5d3b8c03-63c1-4f20-860a-89d424badad8@gmail.com
|
|
This contains various tables for initialising the RTL8814A, plus TX
power limits.
Also add rtw8814a_table.h.
Split into two patches because they are big.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/4c48e35e-1b04-42ed-940e-0e931693def6@gmail.com
|
|
This contains various tables for initialising the RTL8814A, plus TX
power limits.
Split into two patches because they are big.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/df0b8ceb-2c2f-4bda-906f-a05c7b4d424c@gmail.com
|
|
Add various register definitions which will be used by the new driver.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/1dcb5abb-26f8-4db5-be36-057de56465e5@gmail.com
|
|
RTL8852BE-VT support for firmware 29.122. Add parser for Bluetooth channel
map report version 7.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250308025832.10400-5-pkshih@realtek.com
|
|
In order to rearrange the structure member, the format update to version 7.
And to parse the report correctly, add the related logic.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250308025832.10400-4-pkshih@realtek.com
|
|
This report will feedback some basic information from firmware(PTA counter,
report counter, mailbox counter etc). And the report version need to match
driver & firmware both side. The original logic break the switch case logic
before driver update the report version. It made the report can not be
parsed correctly. Delete the break at the version 7 and 8.
Add logic to count C2H event report.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250308025832.10400-3-pkshih@realtek.com
|
|
Add format version of Wi-Fi firmware commands/events for firmware
version 0.29.122.0.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250308025832.10400-2-pkshih@realtek.com
|
|
Some of 11ax AP set the UL HE-SIG-A2 reserved subfield to all 0s, which
will cause the 11be chip to recognize trigger frame as EHT. We propose
a method to bypass the "UL HE-SIG-A2 reserved subfield" and always uses
HE TB in response to the AP's trigger frame.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250306021144.12854-6-pkshih@realtek.com
|
|
The 8922A now supports dynamic antenna gain. However, in firmware
before v0.35.64.0, different transmit powers cannot be applied to
each RF path. To comply with regulatory limits in these older
firmware, the lower of the two requested transmit powers will
be used for both paths when they differ.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250306021144.12854-5-pkshih@realtek.com
|
|
The dynamic antenna gain (DAG) considers the country, meaning DAG can
be activated only when countries and regulatory domains allow it.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250306021144.12854-4-pkshih@realtek.com
|
|
TAS state switching mechanism now incorporates the TX ratio as a
decision parameter. The average power calculation has been improved
by using a higher resolution conversion from dBm to linear. During
scan or MCC operations, TAS state is forced to static SAR and
suspend the average power calculation. Additionally, TAS window
size depends on the regulatory domain and band to ensure compliance.
TAS is enabled when permitted by the regulatory domain and is
currently supported on the 8852CE.
For debugging, add a flag to disable_dm that can stop TAS mechanism.
Co-developed-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250306021144.12854-3-pkshih@realtek.com
|
|
Enhanced the dBm to linear conversion function to accommodate negative
dBm values and improved the precision from 1 dBm to 0.25 dBm.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250306021144.12854-2-pkshih@realtek.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext
Pull sched_ext fix from Tejun Heo:
"BPF schedulers could trigger a crash by passing in an invalid CPU to
the scx_bpf_select_cpu_dfl() helper.
Fix it by verifying input validity"
* tag 'sched_ext-for-6.14-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext:
sched_ext: Validate prev_cpu in scx_bpf_select_cpu_dfl()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple of driver specific fixes, an error handling fix for the Atmel
QuadSPI driver and a fix for a nasty synchronisation issue in the data
path for the Microchip driver which affects larger transfers.
There's also a MAINTAINERS update for the Samsung driver"
* tag 'spi-fix-v6.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: microchip-core: prevent RX overflows when transmit size > FIFO size
MAINTAINERS: add tambarus as R for Samsung SPI
spi: atmel-quadspi: remove references to runtime PM on error path
|
|
Don't error out on large MTU if XDP is multi-buf.
The ping test now tests ping with XDP and high MTU.
netdevsim doesn't actually run the prog (yet?) so
it doesn't matter if the prog was multi-buf..
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://patch.msgid.link/20250311092820.542148-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Stanislav Fomichev says:
====================
net: remove rtnl_lock from the callers of queue APIs
All drivers that use queue management APIs already depend on the netdev
lock. Ultimately, we want to have most of the paths that work with
specific netdev to be rtnl_lock-free (ethtool mostly in particular).
Queue API currently has a much smaller API surface, so start with
rtnl_lock from it:
- add mutex to each dmabuf binding (to replace rtnl_lock)
- move netdev lock management to the callers of netdev_rx_queue_restart
and drop rtnl_lock
====================
Link: https://patch.msgid.link/20250311144026.4154277-1-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All drivers that use queue API are already converted to use
netdev instance lock. Move netdev instance lock management to
the netlink layer and drop rtnl_lock.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Mina Almasry. <almasrymina@google.com>
Link: https://patch.msgid.link/20250311144026.4154277-4-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As we move away from rtnl_lock for queue ops, introduce
per-netdev_nl_sock lock.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250311144026.4154277-3-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No functional changes. Next patches will add more granular locking
to netdev_nl_sock.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250311144026.4154277-2-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Although it does not seem to have any untoward side-effects,
the use of ';' to separate to assignments seems more appropriate than ','.
Flagged by clang-19 -Wcomma
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250307-mlx5-comma-v1-1-934deb6927bb@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 51bef03e1a71 ("selftests/net: deflake GRO tests") recently
switched to NAPI suspension, and lowered the timeout from 1ms to 100us.
This started causing flakes in netdev-run CI. Let's bump it to 200us.
In a quick test of a debug kernel I see failures with 100us, with 200us
in 5 runs I see 2 completely clean runs and 3 with a single retry
(GRO test will retry up to 5 times).
Reviewed-by: Kevin Krakauer <krakauer@google.com>
Link: https://patch.msgid.link/20250310110821.385621-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
bnxt_dl_reload_up is completely missing instance lock management
which can result in `devlink dev reload` leaving with instance
lock held. Add the missing calls.
Also add netdev_assert_locked to make it clear that the up() method
is running with the instance lock grabbed.
v2:
- add net/netdev_lock.h include to bnxt_devlink.c for netdev_assert_locked
Fixes: 004b5008016a ("eth: bnxt: remove most dependencies on RTNL")
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250309215851.2003708-3-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
netdev_lock_ops conditionally grabs instance lock when queue_mgmt_ops
is defined. However queue_mgmt_ops support is signaled via FW
so we can sometimes boot without queue_mgmt_ops being set.
This will result in bnxt running without instance lock which
the driver now heavily depends on. Set request_ops_lock to true
unconditionally to always request netdev instance lock.
Fixes: 004b5008016a ("eth: bnxt: remove most dependencies on RTNL")
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250309215851.2003708-2-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All (error) paths that call dev_close are already holding instance lock,
so switch to netif_close to avoid the deadlock.
v2:
- add missing EXPORT_MODULE for netif_close
Fixes: 004b5008016a ("eth: bnxt: remove most dependencies on RTNL")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250309215851.2003708-1-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a couple of places from which we can arrive to ndo_setup_tc
with TC_SETUP_BLOCK/TC_SETUP_FT:
- netlink
- netlink notifier
- netdev notifier
Locking netdev too deep in this call chain seems to be problematic
(especially assuming some/all of the call_netdevice_notifiers
NETDEV_UNREGISTER) might soon be running with the instance lock).
Revert to lockless ndo_setup_tc for TC_SETUP_BLOCK/TC_SETUP_FT. NFT
framework already takes care of most of the locking. Document
the assumptions.
ndo_setup_tc TC_SETUP_BLOCK
nft_block_offload_cmd
nft_chain_offload_cmd
nft_flow_block_chain
nft_flow_offload_chain
nft_flow_rule_offload_abort
nft_flow_rule_offload_commit
nft_flow_rule_offload_commit
nf_tables_commit
nfnetlink_rcv_batch
nfnetlink_rcv_skb_batch
nfnetlink_rcv
nft_offload_netdev_event
NETDEV_UNREGISTER notifier
ndo_setup_tc TC_SETUP_FT
nf_flow_table_offload_cmd
nf_flow_table_offload_setup
nft_unregister_flowtable_hook
nft_register_flowtable_net_hooks
nft_flowtable_update
nf_tables_newflowtable
nfnetlink_rcv_batch (.call NFNL_CB_BATCH)
nft_flowtable_update
nf_tables_newflowtable
nft_flowtable_event
nf_tables_flowtable_event
NETDEV_UNREGISTER notifier
__nft_unregister_flowtable_net_hooks
nft_unregister_flowtable_net_hooks
nf_tables_commit
nfnetlink_rcv_batch (.call NFNL_CB_BATCH)
__nf_tables_abort
nf_tables_abort
nfnetlink_rcv_batch
__nft_release_hook
__nft_release_hooks
nf_tables_pre_exit_net -> module unload
nft_rcv_nl_event
netlink_register_notifier (oh boy)
nft_register_flowtable_net_hooks
nft_flowtable_update
nf_tables_newflowtable
nf_tables_newflowtable
Fixes: c4f0f30b424e ("net: hold netdev instance lock during nft ndo_setup_tc")
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reported-by: syzbot+0afb4bcf91e5a1afdcad@syzkaller.appspotmail.com
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250308044726.1193222-1-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
nf_conntrack_max and nf_conntrack_expect_max sysctls were authorized to
be written any negative value, which would then be stored in the
unsigned int variables nf_conntrack_max and nf_ct_expect_max variables.
While the do_proc_dointvec_conv function is supposed to limit writing
handled by proc_dointvec proc_handler to INT_MAX. Such a negative value
being written in an unsigned int leads to a very high value, exceeding
this limit.
Moreover, the nf_conntrack_expect_max sysctl documentation specifies the
minimum value is 1.
The proc_handlers have thus been updated to proc_dointvec_minmax in
order to specify the following write bounds :
* Bound nf_conntrack_max sysctl writings between SYSCTL_ZERO
and SYSCTL_INT_MAX.
* Bound nf_conntrack_expect_max sysctl writings between SYSCTL_ONE
and SYSCTL_INT_MAX as defined in the sysctl documentation.
With this patch applied, sysctl writes outside the defined in the bound
will thus lead to a write error :
```
sysctl -w net.netfilter.nf_conntrack_expect_max=-1
sysctl: setting key "net.netfilter.nf_conntrack_expect_max": Invalid argument
```
Signed-off-by: Nicolas Bouchinet <nicolas.bouchinet@ssi.gouv.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Cong Wang says:
====================
net_sched: Prevent creation of classes with TC_H_ROOT
This patchset contains a bug fix and its TDC test case.
====================
Link: https://patch.msgid.link/20250306232355.93864-1-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Integrate the reproduer from Mingi to TDC.
All test results:
1..4
ok 1 0385 - Create DRR with default setting
ok 2 2375 - Delete DRR with handle
ok 3 3092 - Show DRR class
ok 4 4009 - Reject creation of DRR class with classid TC_H_ROOT
Cc: Mingi Cho <mincho@theori.io>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250306232355.93864-3-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The function qdisc_tree_reduce_backlog() uses TC_H_ROOT as a termination
condition when traversing up the qdisc tree to update parent backlog
counters. However, if a class is created with classid TC_H_ROOT, the
traversal terminates prematurely at this class instead of reaching the
actual root qdisc, causing parent statistics to be incorrectly maintained.
In case of DRR, this could lead to a crash as reported by Mingi Cho.
Prevent the creation of any Qdisc class with classid TC_H_ROOT
(0xFFFFFFFF) across all qdisc types, as suggested by Jamal.
Reported-by: Mingi Cho <mincho@theori.io>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 066a3b5b2346 ("[NET_SCHED] sch_api: fix qdisc_tree_decrease_qlen() loop")
Link: https://patch.msgid.link/20250306232355.93864-2-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PRT BOs may not have any backing store, so bo->tbo.resource will be
NULL. Check for that before dereferencing.
Fixes: 0cce5f285d9a ("drm/amdkfd: Check correct memory types for is_system variable")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Natalie Vock <natalie.vock@gmx.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 3e3fcd29b505cebed659311337ea03b7698767fc)
Cc: stable@vger.kernel.org # 6.12.x
|
|
[Why]
If reset is detected and kfd need to evict working queues, HWS moving queue will be failed.
Then remaining queues are not evicted and in active state.
After reset done, kfd uses HWS to termination remaining activated queues but HWS is resetted.
So remove queue will be failed again.
[How]
Keep removing all queues even if HWS returns failed.
It will not affect cpsch as it checks reset_domain->sem.
v2: If any queue failed, evict queue returns error.
v3: Declare err inside the if-block.
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Yifan Zha <Yifan.Zha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 42c854b8fb0cce512534aa2b7141948e80c6ebb0)
Cc: stable@vger.kernel.org
|
|
There is no difference between the sge of READ and non-READ
operations in hns RoCE. Set max_sge_rd to the same value as
max_send_sge.
Fixes: 9a4435375cd1 ("IB/hns: Add driver files for hns RoCE driver")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20250311084857.3803665-8-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
