| Age | Commit message (Collapse) | Author |
|---|
|
With RGMII, we need a 1.5 to 2ns skew between clock and data lines. The
VSC8601 can handle this internally. While the VSC8601 can set more
fine-grained delays, the standard skew settings work out of the box.
The same heuristic is used to determine when this skew should be enabled
as in vsc824x_config_init().
Tested on custom board with AM3352 SOC and VSC801 PHY.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I returned to Synopsys and so I am sending this patch to update the email
address of the pcie-designware-plat author.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
I accepted the invitation from Pratyush to replace him in the
pcie-designware maintenance. This patch makes the maintainer replacement
and simplifies the pcie-designware* maintenance structure.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
CC: Jose Abreu <Jose.Abreu@synopsys.com>
|
|
Calling napi_hash_del() before netif_napi_del() is dangerous
if a synchronize_rcu() is not enforced before NAPI struct freeing.
Lets leave this detail to core networking stack and feel
more comfortable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Calling napi_hash_del() before netif_napi_del() is dangerous
if a synchronize_rcu() is not enforced before NAPI struct freeing.
Lets leave this detail to core networking stack and feel
more comfortable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netdev->real_num_rx_queues setting is only available if CONFIG_SYSFS
is enabled, so we now get a build failure when that is turned off:
netronome/nfp/nfp_net_common.c: In function 'nfp_net_ring_swap_enable':
netronome/nfp/nfp_net_common.c:2489:18: error: 'struct net_device' has no member named 'real_num_rx_queues'; did you mean 'real_num_tx_queues'?
As far as I can tell, the check here is only used as an optimization that
we can skip in order to fix the compilation. If sysfs is disabled,
the following netif_set_real_num_rx_queues() has no effect.
Fixes: 164d1e9e5d52 ("nfp: add support for ethtool .set_channels")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Calling napi_hash_del() after netif_napi_del() is pointless.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Bert Kenward <bkenward@solarflare.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes the lwtunnel_headroom() function which is called
in ipv4_mtu() and ip6_mtu(), to also return the correct headroom
value when the lwtunnel state is OUTPUT_REDIRECT.
This patch enables e.g. SR-IPv6 encapsulations to work without
manually setting the route mtu.
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid breaking cross-compiled ACPI tools builds by rearranging the
handling of kernel header files.
This patch also contains OUTPUT/srctree cleanups in order to make above fix
working for various build environments.
Fixes: e323c02dee59 (ACPICA: MSVC9: Fix <sys/stat.h> inclusion order issue)
Reported-and-tested-by: Yisheng Xie <xieyisheng1@huawei.com>
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The recent merge commit bb598c1b8c9b ("Merge
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net") would cause
the FIB abort warning to fire whenever we flush the FIB tables - either
during module removal or actual abort.
Move it back to its rightful location in the FIB abort function.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SPEED_UNFORCED indicates the MAC & PHY should perform
auto-negotiation to determine a speed which works. If this is called
for, don't set the force bit. If it is set, the MAC actually does
10Gbps, why the internal PHYs don't support.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems many drivers do not respect napi_hash_del() contract.
When napi_hash_del() is used before netif_napi_del(), an RCU grace
period is needed before freeing NAPI object.
Fixes: 91815639d880 ("virtio-net: rx busy polling support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some devices on Fam17h can only be accessed through the System Management
Network (SMN). The SMN is accessed by a pair of index/data registers in PCI
config space. Add a pair of functions to read from and write to the SMN.
The Data Fabric on Fam17h allows multiple devices to use the same register
space. The registers of a specific device are accessed indirectly using the
device's DF InstanceId. Currently, we only need to read from these devices,
so only define a read function for now.
Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/1478812257-5424-5-git-send-email-Yazen.Ghannam@amd.com
[ Boris: make __amd_smn_rw() even more compact. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
AMD Fam17h uses a Data Fabric component instead of a traditional
Northbridge. However, the DF is similar to a NB in that there is one per
die and it uses PCI config D18Fx registers. So let's reuse the existing
AMD_NB infrastructure for Data Fabrics.
Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/1478812257-5424-4-git-send-email-Yazen.Ghannam@amd.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Make all EXPORT_SYMBOL's into EXPORT_SYMBOL_GPL. While we're at it let's
fix some checkpatch warnings.
Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/1478812257-5424-3-git-send-email-Yazen.Ghannam@amd.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Hide amd_northbridges in amd_nb.c so that external callers will have to
use the exported accessor functions.
Also, fix some checkpatch.pl warnings.
Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/1478812257-5424-2-git-send-email-Yazen.Ghannam@amd.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This option was added in 6a89a314ab107a12af08c71420c19a37a30fc2d3 to
allow use of the devm_gpio_* functions without CONFIG_GPIOLIB.
However, only a few months later in
b69ac52449c658b7ac40034dc3c5f5f4a71a723d, CONFIG_GPIOLIB was added
as a dependency, defeating the original purpose of this option.
Instead of that patch, the original commit could have just been
reverted (and in fact was partially so in
403c1d0be5ccbd750d25c59d8358843a81e52e3b). Further, since this
option has a dependency on HAS_IOMEM, even though it does not
require it, it causes build failures when !HAS_IOMEM (e.g. in a
uml build).
Fix that by completely removing the option, in essence completing
the reversion of the original commit.
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The nvme_remove function tears down all allocated resources in the correct
order, so no need to free queues on error during initialization. This
fixes possible use-after-free errors when queues are still associated
with a blk-mq hctx.
Reported-by: Scott Bauer <scott.bauer@intel.com>
Tested-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimbeg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
check array index first and then visit the array.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-fixes
Pull Allwinner clock fixes from Maxime Ripard:
Two fixes, one for the old clock code, one for the new implementation.
* tag 'sunxi-clk-fixes-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
clk: sunxi: Fix M factor computation for APB1
clk: sunxi-ng: sun6i-a31: Force AHB1 clock to use PLL6 as parent
|
|
Dan Carpenter reports that we're passing a pointer to a pointer
here when we should just be passing a pointer. Pass the right
pointer so that the of_clk_hw_onecell_get() sees the appropriate
data pointer on its end.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 9337631f52a8 ("clk: efm32gg: Migrate to clk_hw based OF and registration APIs")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Dan Carpenter reports that we're passing a pointer to a pointer
here when we should just be passing a pointer. Pass the right
pointer so that the of_clk_hw_onecell_get() sees the appropriate
data pointer on its end.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Jisheng Zhang <jszhang@marvell.com>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Fixes: f6475e298297 ("clk: berlin: Migrate to clk_hw based registration and OF APIs")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Tom Lendacky says:
====================
amd-xgbe: AMD XGBE driver updates 2016-11-15
This patch series addresses some minor issues found in the recently
accepted patch series for the AMD XGBE driver.
The following fixes are included in this driver update series:
- Fix a possibly uninitialized variable in the debugfs support
- Fix the GPIO pin number constraint check
This patch series is based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GPIO support in the hardware allows for up to 16 GPIO pins, enumerated
from 0 to 15. The driver uses the wrong value (16) to validate the GPIO
pin range in the routines to set and clear the GPIO output pins. Update
the code to use the correct value (15).
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The debugfs support in the driver uses a common routine to write the
debugfs values. In this routine, if the input file position is non-zero
then the write routine will not return an error and an output parameter
will not have been set. Because an error isn't returned an uninitialized
value will be written into a register.
Fix the common write routine to return an error if the input file position
is non-zero, which will propagate back to the caller.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Florian Fainelli says:
====================
net: Implenent ethtool::nway_reset for a few drivers
This patch series depends on "net: phy: Centralize auto-negotation restart"
since it provides phy_ethtool_nway_reset as a helper function.
The drivers here already support PHYLIB, so there really is no reason why
restarting auto-negotiation would not be possible with these.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement ethtool::nway_reset using phy_ethtool_nway_reset. We are
already using dev->phydev all over the place so this comes for free.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement ethtool::nway_reset using phy_ethtool_nway_reset. We are
already using dev->phydev all over the place so this comes for free.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement ethtool::nway_reset using phy_ethtool_nway_reset. We are
already using dev->phydev all over the place so this comes for free.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement ethtool::nway_reset using phy_ethtool_nway_reset. We are
already using dev->phydev all over the place so this comes for free.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Utilize the generic phy_ethtool_nway_reset() helper function to
implement an autonegotiation restart.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eric Dumazet says:
====================
net: busy-poll: allow preemption and other optimizations
It is time to have preemption points in sk_busy_loop() and improve
its scalability.
Also napi_complete() and friends can tell drivers when it is safe to
not re-enable device interrupts, saving some overhead under
high busy polling.
mlx4 and bnx2x are changed accordingly, to show how this busy polling
status can be exploited by drivers.
Next steps will implement Zach Brown suggestion, where NAPI polling
would be enabled all the time for some chosen queues.
This is needed for efficient epoll() support anyway.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch from napi_complete() to napi_complete_done()
for better GRO support (gro_flush_timeout) and core NAPI
features.
Do not rearm interrupts if we are busy polling,
to reduce bus and interrupts overhead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not rearm interrupts if we are busy polling.
mlx4 uses separate CQ for TX and RX, so number of TX interrupts
does not change, unfortunately.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NAPI drivers use napi_complete_done() or napi_complete() when
they drained RX ring and right before re-enabling device interrupts.
In busy polling, we can avoid interrupts being delivered since
we are polling RX ring in a controlled loop.
Drivers can chose to use napi_complete_done() return value
to reduce interrupts overhead while busy polling is active.
This is optional, legacy drivers should work fine even
if not updated.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now sk_busy_loop() can schedule by itself, we can remove
need_resched() check from sk_can_busy_loop()
Also add a const to its struct sock parameter.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit 4cd13c21b207 ("softirq: Let ksoftirqd do its job"),
sk_busy_loop() needs a bit of care :
softirqs might be delayed since we do not allow preemption yet.
This patch adds preemptiom points in sk_busy_loop(),
and makes sure no unnecessary cache line dirtying
or atomic operations are done while looping.
A new flag is added into napi->state : NAPI_STATE_IN_BUSY_POLL
This prevents napi_complete_done() from clearing NAPIF_STATE_SCHED,
so that sk_busy_loop() does not have to grab it again.
Similarly, netpoll_poll_lock() is done one time.
This gives about 10 to 20 % improvement in various busy polling
tests, especially when many threads are busy polling in
configurations with large number of NIC queues.
This should allow experimenting with bigger delays without
hurting overall latencies.
Tested:
On a 40Gb mlx4 NIC, 32 RX/TX queues.
echo 70 >/proc/sys/net/core/busy_read
for i in `seq 1 40`; do echo -n $i: ; ./super_netperf $i -H lpaa24 -t UDP_RR -- -N -n; done
Before: After:
1: 90072 92819
2: 157289 184007
3: 235772 213504
4: 344074 357513
5: 394755 458267
6: 461151 487819
7: 549116 625963
8: 544423 716219
9: 720460 738446
10: 794686 837612
11: 915998 923960
12: 937507 925107
13: 1019677 971506
14: 1046831 1113650
15: 1114154 1148902
16: 1105221 1179263
17: 1266552 1299585
18: 1258454 1383817
19: 1341453 1312194
20: 1363557 1488487
21: 1387979 1501004
22: 1417552 1601683
23: 1550049 1642002
24: 1568876 1601915
25: 1560239 1683607
26: 1640207 1745211
27: 1706540 1723574
28: 1638518 1722036
29: 1734309 1757447
30: 1782007 1855436
31: 1724806 1888539
32: 1717716 1944297
33: 1778716 1869118
34: 1805738 1983466
35: 1815694 2020758
36: 1893059 2035632
37: 1843406 2034653
38: 1888830 2086580
39: 1972827 2143567
40: 1877729 2181851
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sunil Goutham says:
====================
net: thunderx: Miscellaneous fixes
This patchset includes fixes for incorrect LMAC credits,
unreliable driver statistics, memory leak upon interface
down e.t.c
Changes from v1:
- As suggested replaced bit shifting with BIT() macro
in the patch 'Fix configuration of L3/L4 length checking'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the following
1. When interface is being teardown and queues are being cleaned up,
free pending SKBs that are in SQ which are either not transmitted
or freed as NAPI is disabled by that time.
2. While interface initialization, delay CFG_DONE notification till
the end to avoid corner cases where TXQs are enabled but CQ
interrupts are not which results blocking transmission and kicking
off watchdog.
3. Check for IFF_UP while re-enabling RBDR interrupts from tasklet.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes multiple issues
1. Convert all driver statistics to percpu counters for accuracy.
2. To avoid multiple CQEs posted by a TSO packet appended to HW,
TSO pkt's SQE has 'post_cqe' not set but a dummy SQE is added
for getting HW transmit completion notification. This dummy
SQE has 'dont_send' set and HW drops the pkt pointed to in this
thus Tx drop counter increases. This patch fixes this by subtracting
SW tx tso counter from HW Tx drop counter for actual packet drop counter.
3. Reset all individual queue's and VNIC HW stats when interface is going down.
4. Getrid off unnecessary counters in hot path.
5. Bringout all CQE error stats i.e both Rx and Tx.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes enabling of HW verification of L3/L4 length and
TCP/UDP checksum which is currently being cleared. Also fixed VLAN
stripping config which is being cleared when multiqset is enabled.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Programming LMAC credits taking 9K frame size by default is incorrect
as for an interface which is one of the many on the same BGX/QLM
no of credits available will be less as Tx FIFO will be divided
across all interfaces. So let's say a BGX with 40G interface and another
BGX with multiple 10G, bandwidth of 10G interfaces will be effected when
traffic is running on both 40G and 10G interfaces simultaneously.
This patch fixes this issue by programming credits based on netdev's MTU.
Also fixed configuring MTU to HW and added CQE counter for pkts which
exceed this value.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the 'bgx_id' determination on 83xx where there are
4 BGX blocks instead of 2 on other platforms.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexander Duyck says:
====================
ipv4: Fix memory leaks and reference issues in fib
This series fixes one major issue and one minor issue in the fib tables.
The major issue is that we had lost the functionality that was flushing the
local table entries from main after we had unmerged the two tries. In
order to regain the functionality I have performed a partial revert and
then moved the functionality for flushing the external entries from main
into fib_unmerge.
The minor issue was a memory leak that could occur in the event that we
weren't able to add an alias to the local trie resulting in the fib alias
being leaked.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a small memory leak that can occur where we leak a fib_alias in the
event of us not being able to insert it into the local table.
Fixes: 0ddcf43d5d4a0 ("ipv4: FIB Local/MAIN table collapse")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch that removed the FIB offload infrastructure was a bit too
aggressive and also removed code needed to clean up us splitting the table
if additional rules were added. Specifically the function
fib_trie_flush_external was called at the end of a new rule being added to
flush the foreign trie entries from the main trie.
I updated the code so that we only call fib_trie_flush_external on the main
table so that we flush the entries for local from main. This way we don't
call it for every rule change which is what was happening previously.
Fixes: 347e3b28c1ba2 ("switchdev: remove FIB offload infrastructure")
Reported-by: Eric Dumazet <edumazet@google.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I made some invalid assumptions with BPF_AND and BPF_MOD that could result in
invalid accesses to bpf map entries. Fix this up by doing a few things
1) Kill BPF_MOD support. This doesn't actually get used by the compiler in real
life and just adds extra complexity.
2) Fix the logic for BPF_AND, don't allow AND of negative numbers and set the
minimum value to 0 for positive AND's.
3) Don't do operations on the ranges if they are set to the limits, as they are
by definition undefined, and allowing arithmetic operations on those values
could make them appear valid when they really aren't.
This fixes the testcase provided by Jann as well as a few other theoretical
problems.
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reserved vectors at the beginning and the end of the vector space get
cpu_possible_mask assigned as their affinity mask.
All other non-auto affine interrupts get the default irq affinity mask
assigned. Using cpu_possible_mask breaks that rule.
Treat them like any other interrupt and use irq_default_affinity as target
mask.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Christoph Hellwig <hch@lst.de>
|
|
The recent addition of reserved vectors at the beginning or the end of the
vector space did not take the reserved vectors at the beginning into
account for the various loop exit conditions. As a consequence the last
vectors of the spread area are not included into the spread algorithm and
are treated like the reserved vectors at the end of the vector space and
get the default affinity mask assigned.
Sum up the affinity vectors and the reserved vectors at the beginning and
use the sum as exit condition.
[ tglx: Fixed all conditions instead of only one and massaged changelog ]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/1479201178-29604-2-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
"A regression fix and bug fix bound for stable"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix fuse_write_end() if zero bytes were copied
fuse: fix root dentry initialization
|
