| Age | Commit message (Collapse) | Author |
|---|
|
Since the heartbeat is statically initialized to its default value,
watchdog_init_timeout() will never look in the device-tree for a
timeout-sec value. Instead of statically initializing heartbeat,
fall back to the default timeout value if watchdog_init_timeout()
fails.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The omap watchdog has the annoying behaviour that writes to most
registers don't have any effect when the watchdog is already running.
Quoting the AM335x reference manual:
To modify the timer counter value (the WDT_WCRR register),
prescaler ratio (the WDT_WCLR[4:2] PTV bit field), delay
configuration value (the WDT_WDLY[31:0] DLY_VALUE bit field), or
the load value (the WDT_WLDR[31:0] TIMER_LOAD bit field), the
watchdog timer must be disabled by using the start/stop sequence
(the WDT_WSPR register).
Currently the timer is stopped in the .probe callback but still there
are possibilities that yield to a situation where omap_wdt_start is
entered with the timer running (e.g. when /dev/watchdog is closed
without stopping and then reopened). In such a case programming the
timeout silently fails!
To circumvent this stop the timer before reprogramming.
Assuming one of the first things the watchdog user does is setting the
timeout explicitly nothing too bad should happen because this explicit
setting works fine.
Fixes: 7768a13c252a ("[PATCH] OMAP: Add Watchdog driver support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Instead of using an over-long expression involving the ?: operator use
an if and instead of an else branch rely on the fact that the data
structure was allocated using devm_kzalloc. This also allows to put the
used helper variable into a more local scope.
There is no functional change.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This way only a single allocation is needed (per device). Also this
simplifies the data structure used by the driver because there is no
need anymore to link from one struct to the other (by means of
watchdog_{set,get}_drvdata).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Instead of (partly) open coding watchdog_init_timeout to determine the
inital timeout use the core function that exists for exactly this
purpose.
As a side effect the "timeout-sec" device-tree property is recognized now
(though currently unused in the omap device trees).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
ti,hwmods doesn't belong into the compatible section but is a property
on it's own. Also reformat the section of required properties to match the
usual style of dt binding documents.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This commit add a driver for the watchdog functionality of the Conexant CX92755
SoC, from the Digicolor series of SoCs. Of 8 system timers provided by the
CX92755, the first one, timer A, can reset the chip when its counter reaches
zero. This driver uses this capability to provide userspace with a standard
watchdog, using the watchdog timer driver core framework. This driver also
implements a reboot handler for the reboot(2) system call.
The watchdog driver shares the timer registers with the CX92755 timer driver
(drivers/clocksource/timer-digicolor.c). The timer driver, however, uses only
timers other than A, so both drivers should coexist.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Add a device tree binding documentation to the watchdog hardware block on the
Conexant CX92755 SoC. The CX92755 is from the Digicolor SoCs series. Other SoCs
in that series may share the same hardware block.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Use endian agnostic IO functions for the watchdog driver for when it
is enabled on ATSAMA5D36 devices running in big endian.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Initial submission adding support for this IP only included Watchdog and
the Real-Time Clock. Now the third (and final) device is enabled this
trivial patch is required to update the comment in the Watchdog driver
to encompass Clocksource.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Signed-off-by: David Paris <david.paris@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
On current ST platforms the LPC controls a number of functions including
Watchdog and Real Time Clock. This patch provides the bindings used to
configure LPC in Watchdog mode.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
ST's Low Power Controller can currently operate in two supported modes;
Watchdog and Real Time Clock. These defines will aid engineers to easily
identify the selected mode.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
* pm-cpuidle:
cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state
|
|
The idle cpus which stay in snooze for a long period can degrade the
perfomance of the sibling cpus. If the cpu stays in snooze for more
than target residency of the next available idle state, then exit from
snooze. This gives a chance to the cpuidle governor to re-evaluate the
last idle state of the cpu to promote it to deeper idle states.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit f61bf13b6a07 ("[media] vb2: add allow_zero_bytesused flag to the
vb2_queue struct") added a WARN_ONCE to catch usage of a deprecated API
using a zero value for v4l2_buffer.bytesused.
However, the condition is checked incorrectly, as the v4L2_buffer
bytesused field is supposed to be ignored for multiplanar buffers. This
results in spurious warnings when using the multiplanar API.
Fix it by checking v4l2_buffer.bytesused for uniplanar buffers and
v4l2_plane.bytesused for multiplanar buffers.
Fixes: f61bf13b6a07 ("[media] vb2: add allow_zero_bytesused flag to the vb2_queue struct")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: stable@vger.kernel.org # for v4.0
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Tested-by: David Sterba <dsterba@suse.cz>
Signed-off-by: David Sterba <dsterba@suse.cz>
|
|
* pm-sleep:
x86: Load __USER_DS into DS/ES after resume
|
|
The clock which was named as 'pll_clk' is actually not the clock source
of PLL in MIPI DSI. This patch fixes this disagreement.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Srinivas Pandruvada reported a problem with system resume from
suspend-to-RAM on 32-bit x86 systems where the DS register of
the CPU is set to __KERNEL_DS instead of __USER_DS on return
to user space which cases a General Protection Fault to occur.
The issue is that DS is set to __KERNEL_DS by the ACPI resume code
path while the SYSEXIT path never reloads DS/ES. It assumes they
are still __USER_DS set at the SYSENTER time (Brian Gerst), so if
the return to user space happens to be through SYSEXIT, it will lead
to the reported GPF.
Fix the problem by setting the DS and ES registers to __USER_DS
as expected by the SYSEXIT path.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=61781
Link: http://marc.info/?l=linux-pm&m=143406648920385&w=2
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
* pm-opp:
PM / OPP: Add binding for 'opp-suspend'
PM / OPP: Allow multiple OPP tables to be passed via DT
PM / OPP: Add new bindings to address shortcomings of existing bindings
|
|
On few platforms, for power efficiency, we want the device to be
configured for a specific OPP while we put the device in suspend state.
Add an optional property in operating-points-v2 bindings for that.
Suggested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
On some platforms (Like Qualcomm's SoCs), it is not decided until
runtime on what OPPs to use. The OPP tables can be fixed at compile
time, but which table to use is found out only after reading some efuses
(sort of an prom) and knowing characteristics of the SoC.
To support such platform we need to pass multiple OPP tables per device
and hardware should be able to choose one and only one table out of
those.
Update operating-points-v2 bindings to support that.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Current OPP (Operating performance point) device tree bindings have been
insufficient due to the inflexible nature of the original bindings. Over
time, we have realized that Operating Performance Point definitions and
usage is varied depending on the SoC and a "single size (just frequency,
voltage) fits all" model which the original bindings attempted and
failed.
The proposed next generation of the bindings addresses by providing a
expandable binding for OPPs and introduces the following common
shortcomings seen with the original bindings:
- Getting clock/voltage/current rails sharing information between CPUs.
Shared by all cores vs independent clock per core vs shared clock per
cluster.
- Support for specifying current levels along with voltages.
- Support for multiple regulators.
- Support for turbo modes.
- Other per OPP settings: transition latencies, disabled status, etc.?
- Expandability of OPPs in future.
This patch introduces new bindings "operating-points-v2" to get these problems
solved. Refer to the bindings for more details.
We now have multiple versions of OPP binding and only one of them should
be used per device.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
If jffs2 can deadlock on overlayfs readdir because it takes the same lock
on ->iterate() as in ->lookup().
Fix by moving whiteout checking outside iterate_dir(). Optimized by
collecting potential whiteouts (DT_CHR) in a temporary list and if
non-empty iterating throug these and checking for a 0/0 chardev.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Fixes: 49c21e1cacd7 ("ovl: check whiteout while reading directory")
Reported-by: Roman Yeryomin <leroi.lists@gmail.com>
|
|
Allow filesystems with .d_revalidate as lower layer(s), but not as upper
layer.
For local filesystems the rule was that modifications on the layers
directly while being part of the overlay results in undefined behavior.
This can easily be extended to distributed filesystems: we assume the tree
used as lower layer is static, which means ->d_revalidate() should always
return "1". If that is not the case, return -ESTALE, don't try to work
around the modification.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
|
|
NFS and other distributed filesystems may place automount points in the
tree. Previoulsy overlayfs refused to mount such filesystems types (based
on the existence of the .d_automount callback), even if the actual export
didn't have any automount points.
It cannot be determined in advance whether the filesystem has automount
points or not. The solution is to allow fs with .d_automount but refuse to
traverse any automount points encountered.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
|
|
The enable field needs to be kept in sync with the mode_blob field. Call
drm_atomic_set_mode_prop_for_crtc() instead of setting enable to false
in order to dereference the mode blob correctly.
v2:
- Check the return value of drm_atomic_set_mode_prop_for_crtc()
- Drop the num_connectors local variable
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: A couple more updates for v4.2
These were sitting on my laptop.
|
|
Using -1 as platform device id means that the platform driver core will not
assign any id to the device (the device name will not have id at all). This
results problems on systems that have multiple PCHs (Platform Controller
HUBs) because all of them also include their own copy of LPC device.
All the subsequent device creations will fail because there already exists
platform device with the same name.
Fix this by passing PLATFORM_DEVID_AUTO as platform device id. This makes
the platform device core to allocate new ids automatically.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Since commit 1c6c69525b40eb76de8adf039409722015927dc3 ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Since commit 1c6c69525b40eb76de8adf039409722015927dc3 ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Since commit 1c6c69525b40eb76de8adf039409722015927dc3 ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Since commit 1c6c69525b40eb76de8adf039409722015927dc3 ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Since commit 1c6c69525b40eb76de8adf039409722015927dc3 ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Since commit 1c6c69525b40eb76de8adf039409722015927dc3 ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Since commit 1c6c69525b40eb76de8adf039409722015927dc3 ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Since commit 1c6c69525b40eb76de8adf039409722015927dc3 ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add device tree bindings for the DA9063 OnKey driver.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add MFD support for the DA9063 OnKey driver
The function da9063_clear_fault_log() is added to mitigate the case of a
hardware power-cut after a long-long OnKey press. Although there is no
software intervention in this case (by definition) such a shutdown would
cause persistent information within the DA9063 FAULT_LOG that would be
available during the next device restart.
Clearance of this persistent register must be completed after such a
hardware power-cut operation has happened so that the FAULT_LOG does not
continue with previous values. The clearance function has been added here
in the kernel driver because wiping the fault-log cannot be counted on
outside the Linux kernel.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
[Lee: Removed 'key_power' for Dmitry to take through the Input Tree]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The use of ifneq against 'n' to conditionally compile codec-specific
parts is wrong and was resulting in all the codec tables being built
even for deselected codecs.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
For the WM5102 there is a dependency in the core code on wm5102_patch()
which only exists when CONFIG_MFD_WM5102 is defined. To avoid having
to sprinkle #ifdefs around the code it is given an alternative empty
stub version when CONFIG_MFD_WM5102 is deselected
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Current code in mfd-core calls into ACPI to check resources even
on a system that booted with a DT (on kernels with both DT and ACPI
support compiled in). This triggers ACPI exceptions since we may
end up calling the ACPI interpreter when it has not been initialized:
"ACPI Exception: AE_BAD_PARAMETER, Thread 2064154624 could not acquire
Mutex [0x1] (20150410/utmutex-285)"
This patch fixes the issues by adding a check for an ACPI companion
device before carrying out ACPI resources checks to avoid calling
the ACPI interpreter if the fwnode representing the device is an OF one.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Later arizona silicon has the single/differential selector
in a different register, and IN1_MODE only selects between
analogue or digital. Prepare for this by splitting the
INx_MODE definition into two fields.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
On the wm5110 it is important the reset line is held for slightly longer
to ensure the device starts up well. This patch adds a 5mS delay for
this.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
