| Age | Commit message (Collapse) | Author |
|---|
|
Pausing and canceling balance can race to interrupt balance lead to BUG_ON
panic in btrfs_cancel_balance. The BUG_ON condition in btrfs_cancel_balance
does not take this race scenario into account.
However, the race condition has no other side effects. We can fix that.
Reproducing it with panic trace like this:
kernel BUG at fs/btrfs/volumes.c:4618!
RIP: 0010:btrfs_cancel_balance+0x5cf/0x6a0
Call Trace:
<TASK>
? do_nanosleep+0x60/0x120
? hrtimer_nanosleep+0xb7/0x1a0
? sched_core_clone_cookie+0x70/0x70
btrfs_ioctl_balance_ctl+0x55/0x70
btrfs_ioctl+0xa46/0xd20
__x64_sys_ioctl+0x7d/0xa0
do_syscall_64+0x38/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Race scenario as follows:
> mutex_unlock(&fs_info->balance_mutex);
> --------------------
> .......issue pause and cancel req in another thread
> --------------------
> ret = __btrfs_balance(fs_info);
>
> mutex_lock(&fs_info->balance_mutex);
> if (ret == -ECANCELED && atomic_read(&fs_info->balance_pause_req)) {
> btrfs_info(fs_info, "balance: paused");
> btrfs_exclop_balance(fs_info, BTRFS_EXCLOP_BALANCE_PAUSED);
> }
CC: stable@vger.kernel.org # 4.19+
Signed-off-by: xiaoshoukui <xiaoshoukui@ruijie.com.cn>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
bio_ctrl->len_to_oe_boundary is used to make sure we stay inside a zone
as we submit bios for writes. Every time we add a page to the bio, we
decrement those bytes from len_to_oe_boundary, and then we submit the
bio if we happen to hit zero.
Most of the time, len_to_oe_boundary gets set to U32_MAX.
submit_extent_page() adds pages into our bio, and the size of the bio
ends up limited by:
- Are we contiguous on disk?
- Does bio_add_page() allow us to stuff more in?
- is len_to_oe_boundary > 0?
The len_to_oe_boundary math starts with U32_MAX, which isn't page or
sector aligned, and subtracts from it until it hits zero. In the
non-zoned case, the last IO we submit before we hit zero is going to be
unaligned, triggering BUGs.
This is hard to trigger because bio_add_page() isn't going to make a bio
of U32_MAX size unless you give it a perfect set of pages and fully
contiguous extents on disk. We can hit it pretty reliably while making
large swapfiles during provisioning because the machine is freshly
booted, mostly idle, and the disk is freshly formatted. It's also
possible to trigger with reads when read_ahead_kb is set to 4GB.
The code has been clean up and shifted around a few times, but this flaw
has been lurking since the counter was added. I think the commit
24e6c8082208 ("btrfs: simplify main loop in submit_extent_page") ended
up exposing the bug.
The fix used here is to skip doing math on len_to_oe_boundary unless
we've changed it from the default U32_MAX value. bio_add_page() is the
real limit we want, and there's no reason to do extra math when block
layer is doing it for us.
Sample reproducer, note you'll need to change the path to the bdi and
device:
SUBVOL=/btrfs/swapvol
SWAPFILE=$SUBVOL/swapfile
SZMB=8192
mkfs.btrfs -f /dev/vdb
mount /dev/vdb /btrfs
btrfs subvol create $SUBVOL
chattr +C $SUBVOL
dd if=/dev/zero of=$SWAPFILE bs=1M count=$SZMB
sync
echo 4 > /proc/sys/vm/drop_caches
echo 4194304 > /sys/class/bdi/btrfs-2/read_ahead_kb
while true; do
echo 1 > /proc/sys/vm/drop_caches
echo 1 > /proc/sys/vm/drop_caches
dd of=/dev/zero if=$SWAPFILE bs=4096M count=2 iflag=fullblock
done
Fixes: 24e6c8082208 ("btrfs: simplify main loop in submit_extent_page")
CC: stable@vger.kernel.org # 6.4+
Reviewed-by: Sweet Tea Dorminy <sweettea-kernel@dorminy.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Fstests with POST_MKFS_CMD="btrfstune -m" (as in the mailing list)
reported a few of the test cases failing.
The failure scenario can be summarized and simplified as follows:
$ mkfs.btrfs -fq -draid1 -mraid1 /dev/sdb1 /dev/sdb2 :0
$ btrfstune -m /dev/sdb1 :0
$ wipefs -a /dev/sdb1 :0
$ mount -o degraded /dev/sdb2 /btrfs :0
$ btrfs replace start -B -f -r 1 /dev/sdb1 /btrfs :1
STDERR:
ERROR: ioctl(DEV_REPLACE_START) failed on "/btrfs": Input/output error
[11290.583502] BTRFS warning (device sdb2): tree block 22036480 mirror 2 has bad fsid, has 99835c32-49f0-4668-9e66-dc277a96b4a6 want da40350c-33ac-4872-92a8-4948ed8c04d0
[11290.586580] BTRFS error (device sdb2): unable to fix up (regular) error at logical 22020096 on dev /dev/sdb8 physical 1048576
As above, the replace is failing because we are verifying the header with
fs_devices::fsid instead of fs_devices::metadata_uuid, despite the
metadata_uuid actually being present.
To fix this, use fs_devices::metadata_uuid. We copy fsid into
fs_devices::metadata_uuid if there is no metadata_uuid, so its fine.
Fixes: a3ddbaebc7c9 ("btrfs: scrub: introduce a helper to verify one metadata block")
CC: stable@vger.kernel.org # 6.4+
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Commit 'fa6999e326fe ("s390/pkey: support CCA and EP11 secure ECC
private keys")' introduced PKEY_TYPE_EP11_AES securekey blobs as a
supplement to the PKEY_TYPE_EP11 (which won't work in environments
with session-bound keys). This new keyblobs has a different maximum
size, so fix paes crypto module to accept also these larger keyblobs.
Fixes: fa6999e326fe ("s390/pkey: support CCA and EP11 secure ECC private keys")
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Reviewed-by: Ingo Franzki <ifranzki@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Commit 'fa6999e326fe ("s390/pkey: support CCA and EP11 secure ECC
private keys")' introduced a new PKEY_TYPE_EP11_AES securekey type as
a supplement to the existing PKEY_TYPE_EP11 (which won't work in
environments with session-bound keys). The pkey EP11 securekey
attributes use PKEY_TYPE_EP11_AES (instead of PKEY_TYPE_EP11)
keyblobs, to make the generated keyblobs usable also in environments,
where session-bound keys are required.
There should be no negative impacts to userspace because the internal
structure of the keyblobs is opaque. The increased size of the
generated keyblobs is reflected by the changed size of the attributes.
Fixes: fa6999e326fe ("s390/pkey: support CCA and EP11 secure ECC private keys")
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Reviewed-by: Ingo Franzki <ifranzki@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Commit 'fa6999e326fe ("s390/pkey: support CCA and EP11 secure ECC
private keys")' introduced a new PKEY_TYPE_EP11_AES type for the
PKEY_VERIFYKEY2 IOCTL to verify keyblobs of this type. Unfortunately,
all PKEY_VERIFYKEY2 IOCTL requests with keyblobs of this type return
with an error (-EINVAL). Fix PKEY_TYPE_EP11_AES handling in
PKEY_VERIFYKEY2 IOCTL, so that userspace can verify keyblobs of this
type.
Fixes: fa6999e326fe ("s390/pkey: support CCA and EP11 secure ECC private keys")
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Reviewed-by: Ingo Franzki <ifranzki@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Commit 'fa6999e326fe ("s390/pkey: support CCA and EP11 secure ECC
private keys")' introduced a new PKEY_TYPE_EP11_AES type for the
PKEY_KBLOB2PROTK2 and a new IOCTL, PKEY_KBLOB2PROTK3, which both
allows userspace to convert opaque securekey blobs of this type into
protectedkey blobs. Unfortunately, all PKEY_KBLOB2PROTK2 and
PKEY_KBLOB2PROTK3 IOCTL requests with this keyblobs of this type
return with an error (-EINVAL). Fix PKEY_TYPE_EP11_AES handling in
PKEY_KBLOB2PROTK2 and PKEY_KBLOB2PROTK3 IOCTLs, so that userspace can
convert PKEY_TYPE_EP11_AES keyblobs into protectedkey blobs.
Add a helper function to decode the start and size of the internal
header as well as start and size of the keyblob payload of an existing
keyblob. Also validate the length of header and keyblob, as well as
the keyblob magic.
Introduce another helper function, which handles a raw key wrapping
request and do the keyblob decoding in the calling function. Remove
all other header-related calculations.
Fixes: fa6999e326fe ("s390/pkey: support CCA and EP11 secure ECC private keys")
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Reviewed-by: Ingo Franzki <ifranzki@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Commit 'fa6999e326fe ("s390/pkey: support CCA and EP11 secure ECC
private keys")' introduced PKEY_TYPE_EP11_AES for the PKEY_CLR2SECK2
IOCTL to convert an AES clearkey into a securekey of this type.
Unfortunately, all PKEY_CLR2SECK2 IOCTL requests with type
PKEY_TYPE_EP11_AES return with an error (-EINVAL). Fix the handling
for PKEY_TYPE_EP11_AES in PKEY_CLR2SECK2 IOCTL, so that userspace can
convert clearkey blobs into PKEY_TYPE_EP11_AES securekey blobs.
Cc: stable@vger.kernel.org # v5.10+
Fixes: fa6999e326fe ("s390/pkey: support CCA and EP11 secure ECC private keys")
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Reviewed-by: Ingo Franzki <ifranzki@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Commit 'fa6999e326fe ("s390/pkey: support CCA and EP11 secure ECC
private keys")' introduced PKEY_TYPE_EP11_AES for the PKEY_GENSECK2
IOCTL, to enable userspace to generate securekey blobs of this
type. Unfortunately, all PKEY_GENSECK2 IOCTL requests for
PKEY_TYPE_EP11_AES return with an error (-EINVAL). Fix the handling
for PKEY_TYPE_EP11_AES in PKEY_GENSECK2 IOCTL, so that userspace can
generate securekey blobs of this type.
The start of the header and the keyblob, as well as the length need
special handling, depending on the internal keyversion. Add a helper
function that splits an uninitialized buffer into start and size of
the header as well as start and size of the payload, depending on the
requested keyversion.
Do the header-related calculations and the raw genkey request handling
in separate functions. Use the raw genkey request function for
internal purposes.
Fixes: fa6999e326fe ("s390/pkey: support CCA and EP11 secure ECC private keys")
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Reviewed-by: Ingo Franzki <ifranzki@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Commit 'fa6999e326fe ("s390/pkey: support CCA and EP11 secure ECC
private keys")' introduced PKEY_TYPE_EP11_AES as a supplement to
PKEY_TYPE_EP11. All pkeys have an internal header/payload structure,
which is opaque to the userspace. The header structures for
PKEY_TYPE_EP11 and PKEY_TYPE_EP11_AES are nearly identical and there
is no reason, why different structures are used. In preparation to fix
the keyversion handling in the broken PKEY IOCTLs, the same header
structure is used for PKEY_TYPE_EP11 and PKEY_TYPE_EP11_AES. This
reduces the number of different code paths and increases the
readability.
Fixes: fa6999e326fe ("s390/pkey: support CCA and EP11 secure ECC private keys")
Signed-off-by: Holger Dengler <dengler@linux.ibm.com>
Reviewed-by: Ingo Franzki <ifranzki@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
loongarch"
Unifying the asm-generic headers across 32-bit and 64-bit architectures
based on the compiler provided macros was a good idea and appears to work
with all user space, but it caused a regression when building old kernels
on systems that have the new headers installed in /usr/include, as this
combination trips an inconsistency in the kernel's own tools/include
headers that are a mix of userspace and kernel-internal headers.
This affects kernel builds on arm64, riscv64 and loongarch64 systems that
might end up using the "#define __BITS_PER_LONG 32" default from the old
tools headers. Backporting the commit into stable kernels would address
this, but it would still break building kernels without that backport,
and waste time for developers trying to understand the problem.
arm64 build machines are rather common, and on riscv64 this can also
happen in practice, but loongarch64 is probably new enough to not
be used much for building old kernels, so only revert the bits
for arm64 and riscv.
Link: https://lore.kernel.org/all/20230731160402.GB1823389@dev-arch.thelio-3990X/
Reported-by: Nathan Chancellor <nathan@kernel.org>
Fixes: 8386f58f8deda ("asm-generic: Unify uapi bitsperlong.h for arm64, riscv and loongarch")
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm ARM64 fixes for v6.5
This corrects the invalid path specifier for L3 interconnects in the CPU
nodes of SM8150 and SM8250. It corrects the compatible of the SC8180X L3
node, to pass the binding check.
The crypto core, and its DMA controller, is disabled on SM8350 to avoid
the system from crashing at boot while the issue is diagnosed.
A thermal zone node name conflict is resolved for PM8150L, on the RB5
board.
The UFS vccq voltage is corrected on the SA877P Ride platform, to
address observed stability issues.
The reg-names of the DSI phy on SC7180 are restored after an accidental
search-and-replace update.
* tag 'qcom-arm64-fixes-for-6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: sc7180: Fix DSI0_PHY reg-names
arm64: dts: qcom: sa8775p-ride: Update L4C parameters
arm64: dts: qcom: qrb5165-rb5: fix thermal zone conflict
arm64: dts: qcom: sm8350: fix BAM DMA crash and reboot
arm64: dts: qcom: sc8180x: Fix OSM L3 compatible
arm64: dts: qcom: sm8250: Fix EPSS L3 interconnect cells
arm64: dts: qcom: sm8150: Fix OSM L3 interconnect cells
Link: https://lore.kernel.org/r/20230815142042.2459048-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps
A fix external abort on non-linefetch for am335x that is fixed with a flush
of posted write. And two networking fixes for beaglebone mostly for revision
c3 to do phy reset with a gpio and to fix a boot time warning.
* tag 'omap-for-v6.5/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-bone-common: Add vcc-supply for on-board eeprom
ARM: dts: am335x-bone-common: Add GPIO PHY reset on revision C3 board
bus: ti-sysc: Flush posted write on enable before reset
Link: https://lore.kernel.org/r/pull-1692158536-457318@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Correct wifi interrupt flags for some boards, fixed wifi on Rock PI4,
disabled hs400 speeds for some boards having problems with data
intergrity and some dt property/styling fixes.
* tag 'v6.5-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Fix Wifi/Bluetooth on ROCK Pi 4 boards
arm64: dts: rockchip: minor whitespace cleanup around '='
arm64: dts: rockchip: Disable HS400 for eMMC on ROCK 4C+
arm64: dts: rockchip: Disable HS400 for eMMC on ROCK Pi 4
arm64: dts: rockchip: add missing space before { on indiedroid nova
arm64: dts: rockchip: correct wifi interrupt flag in Box Demo
arm64: dts: rockchip: correct wifi interrupt flag in Rock Pi 4B
arm64: dts: rockchip: correct wifi interrupt flag in eaidk-610
arm64: dts: rockchip: Drop invalid regulator-init-microvolt property
Link: https://lore.kernel.org/r/4519945.8hzESeGDPO@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
fixed register access error when switching to other tas2781 -- refresh the page
inside regmap on the switched tas2781
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://lore.kernel.org/r/20230817093257.951-1-shenghao-ding@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
An ACPI ID has been allocated for CS35L56 ASoC devices so that they can
be instantiated from ACPI Device entries.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230817112712.16637-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use a device property "cirrus,firmware-uid" to get the unique firmware
identifier instead of using ACPI _SUB. There aren't any products that use
_SUB.
There will not usually be a _SUB in Soundwire nodes. The ACPI can use a
_DSD section for custom properties.
There is also a need to support instantiating this driver using software
nodes. This is for systems where the CS35L56 is a back-end device and the
ACPI refers only to the front-end audio device - there will not be any ACPI
references to CS35L56.
Fixes: e49611252900 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Signed-off-by: Maciej Strozek <mstrozek@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230817112712.16637-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This reverts commit ca62297b2085b5b3168bd891ca24862242c635a1.
Commit ca62297b2085 ("drm/edid: Fix csync detailed mode parsing") fixed
EDID detailed mode sync parsing. Unfortunately, there are quite a few
displays out there that have bogus (zero) sync field that are broken by
the change. Zero means analog composite sync, which is not right for
digital displays, and the modes get rejected. Regardless, it used to
work, and it needs to continue to work. Revert the change.
Rejecting modes with analog composite sync was the part that fixed the
gitlab issue 8146 [1]. We'll need to get back to the drawing board with
that.
[1] https://gitlab.freedesktop.org/drm/intel/-/issues/8146
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8789
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8930
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9044
Fixes: ca62297b2085 ("drm/edid: Fix csync detailed mode parsing")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v6.4+
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230815101907.2900768-1-jani.nikula@intel.com
|
|
Christian reported spurious module load crashes after some of Song's
module memory layout patches.
Turns out that if the very last instruction on the very last page of the
module is a 'JMP __x86_return_thunk' then __static_call_fixup() will
trip a fault and die.
And while the module rework made this slightly more likely to happen,
it's always been possible.
Fixes: ee88d363d156 ("x86,static_call: Use alternative RET encoding")
Reported-by: Christian Bricart <christian@bricart.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Link: https://lkml.kernel.org/r/20230816104419.GA982867@hirez.programming.kicks-ass.net
|
|
The CS42L43 is an audio CODEC with integrated MIPI SoundWire interface
(Version 1.2.1 compliant), I2C, SPI, and I2S/TDM interfaces designed
for portable applications. It provides a high dynamic range, stereo
DAC for headphone output, two integrated Class D amplifiers for
loudspeakers, and two ADCs for wired headset microphone input or
stereo line input. PDM inputs are provided for digital microphones.
Add a basic pinctrl driver which supports driver strength for the
various pins, gpios, and pinmux for the 2 multi-function pins.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230804104602.395892-5-ckeepax@opensource.cirrus.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The CS42L43 is an audio CODEC with integrated MIPI SoundWire interface
(Version 1.2.1 compliant), I2C, SPI, and I2S/TDM interfaces designed
for portable applications. It provides a high dynamic range, stereo
DAC for headphone output, two integrated Class D amplifiers for
loudspeakers, and two ADCs for wired headset microphone input or
stereo line input. PDM inputs are provided for digital microphones.
The MFD component registers and initialises the device and provides
PM/system power management.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230804104602.395892-4-ckeepax@opensource.cirrus.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The CS42L43 is an audio CODEC with integrated MIPI SoundWire interface
(Version 1.2.1 compliant), I2C, SPI, and I2S/TDM interfaces designed
for portable applications. It provides a high dynamic range, stereo
DAC for headphone output, two integrated Class D amplifiers for
loudspeakers, and two ADCs for wired headset microphone input or
stereo line input. PDM inputs are provided for digital microphones.
Add a YAML DT binding document for this device.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230804104602.395892-3-ckeepax@opensource.cirrus.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Currently the in-band alerts for SoundWire peripherals can only
be communicated to the driver through the interrupt_callback
function. This however is slightly inconvenient for devices that wish
to share IRQ handling code between SoundWire and I2C/SPI, the later
would normally register an IRQ handler with the IRQ subsystem. However
there is no reason the SoundWire in-band IRQs can not also be
communicated as an actual IRQ to the driver.
Add support for SoundWire peripherals to register a normal IRQ
handler to receive SoundWire in-band alerts, allowing code to be
shared across control buses. Note that we allow users to use both the
interrupt_callback and the IRQ handler, this is useful for devices
which must clear additional chip specific SoundWire registers that are
not a part of the normal IRQ flow, or the SoundWire specification.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230804104602.395892-2-ckeepax@opensource.cirrus.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Because the cost of calling tick_nohz_get_sleep_length() may increase
in the future, reorder the code in menu_select() so it first uses the
statistics to determine the expected idle duration. If that value is
higher than RESIDENCY_THRESHOLD_NS, tick_nohz_get_sleep_length() will
be called to obtain the time till the closest timer and refine the
idle duration prediction if necessary.
This causes the governor to always take the full overhead of
get_typical_interval() with the assumption that the cost will be
amortized by skipping the tick_nohz_get_sleep_length() call in the
cases when the predicted idle duration is relatively very small.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Doug Smythies <dsmythies@telus.net>
|
|
Move the acpi_bus_generate_netlink_event() invocation into
acpi_thermal_trips_update() which allows the code duplication in
acpi_thermal_notify() to be cleaned up, but for this purpose the
event value needs to be passed to acpi_thermal_trips_update() and
from there to acpi_thermal_adjust_thermal_zone() which has to
determine the flag value for __acpi_thermal_trips_update() by
itself.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Drop the .get_trip_type(), .get_trip_temp() and .get_crit_temp() thermal
zone callbacks that are not necessary any more from the ACPI thermal
driver along with the corresponding callback functions.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Rework the ACPI thermal driver's .get_trend() callback function,
thermal_get_trend(), so that it does not call thermal_get_trip_type()
and thermal_get_trip_temp() which are going to be dropped.
This reduces the overhead of the function too, because it will always
carry out a trip point lookup once after the change.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Make the ACPI thermal driver use thermal_zone_device_register_with_trips()
to register its thermal zones.
For this purpose, make it create a trip point table that will be passed to
thermal_zone_device_register_with_trips() as an argument.
Also use the thermal_zone_update_trip_temp() helper introduced
previously to update temperatures of the passive and active trip
points after a trip points change notification from the platform
firmware.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Rework the currently unused __for_each_thermal_trip() to pass original
pointers to struct thermal_trip objects to the callback, so it can be
used for updating trip data (e.g. temperatures), rename it to
for_each_thermal_trip() and make it available to modular drivers.
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add struct acpi_thermal_trip to contain the temperature and valid flag
of each trip point in the driver's local data structures.
This helps to make the subsequent changes more straightforward.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There is a race condition between acpi_thermal_trips_update() and
acpi_thermal_check_fn(), because the trip points may get updated while
the latter is running which in theory may lead to inconsistent results.
For example, if two trips are updated together, using the temperature
value of one of them from before the update and the temperature value
of the other one from after the update may not lead to the expected
outcome.
Moreover, if thermal_get_trend() runs when a trip points update is in
progress, it may end up using stale trip point temperatures.
To address this, make acpi_thermal_trips_update() call
thermal_zone_device_exec() to carry out the trip points update and
use a new acpi_thermal_adjust_thermal_zone() wrapper around
__acpi_thermal_trips_update() as the callback function for the latter.
While at it, change the acpi_thermal_trips_update() return data type
to void as that function always returns 0 anyway.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Rename the trips variable in acpi_thermal_register_thermal_zone() to
trip_count so its name better reflects the purpose, rearrange white
space in the loop over active trips for clarity and reduce code
duplication related to calling thermal_zone_device_register() by
using an extra local variable to store the passive delay value.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add a new field called priv to struct thermal_trip to allow thermal
drivers to store pointers to their local data associated with trip
points.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Introduce a new helper function, thermal_zone_device_exec(), that can
be used by drivers to run a given callback routine under the zone lock.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The function cppc_freq_invariance_init() may failed to create
kworker_fie, make it more robust by setting fie_disabled to FIE_DISBALED
to prevent an invalid pointer dereference in kthread_destroy_worker(),
which called from cppc_freq_invariance_exit().
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The cpufreq framework used to use the zero of return value to reflect
the cppc_cpufreq_get_rate() had failed to get current frequecy and treat
all positive integer to be succeed. Since cppc_get_perf_ctrs() returns a
negative integer in error case, so it is better to convert the value to
zero as the return value of cppc_cpufreq_get_rate().
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
When a cpufreq_policy is allocated, the cpus, related_cpus and real_cpus
of policy are still unset. Therefore, it is preferable to print the
passed 'cpu' parameter instead of a empty 'cpus' cpumask in error
message when registering MIN/MAX QoS notifier fails.
Signed-off-by: Liao Chang <liaochang1@huawei.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
If the switch is reset during active EEPROM transactions, as in
just after an SoC reset after power up, the I2C bus transaction
may be cut short leaving the EEPROM internal I2C state machine
in the wrong state. When the switch is reset again, the bad
state machine state may result in data being read from the wrong
memory location causing the switch to enter unexpected mode
rendering it inoperational.
Fixes: a3dcb3e7e70c ("net: dsa: mv88e6xxx: Wait for EEPROM done after HW reset")
Signed-off-by: Alfred Lee <l00g33k@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230815001323.24739-1-l00g33k@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2023-08-16
We've added 17 non-merge commits during the last 6 day(s) which contain
a total of 20 files changed, 1179 insertions(+), 37 deletions(-).
The main changes are:
1) Add a BPF hook in sys_socket() to change the protocol ID
from IPPROTO_TCP to IPPROTO_MPTCP to cover migration for legacy
applications, from Geliang Tang.
2) Follow-up/fallout fix from the SO_REUSEPORT + bpf_sk_assign work
to fix a splat on non-fullsock sks in inet[6]_steal_sock,
from Lorenz Bauer.
3) Improvements to struct_ops links to avoid forcing presence of
update/validate callbacks. Also add bpf_struct_ops fields documentation,
from David Vernet.
4) Ensure libbpf sets close-on-exec flag on gzopen, from Marco Vedovati.
5) Several new tcx selftest additions and bpftool link show support for
tcx and xdp links, from Daniel Borkmann.
6) Fix a smatch warning on uninitialized symbol in
bpf_perf_link_fill_kprobe, from Yafang Shao.
7) BPF selftest fixes e.g. misplaced break in kfunc_call test,
from Yipeng Zou.
8) Small cleanup to remove unused declaration bpf_link_new_file,
from Yue Haibing.
9) Small typo fix to bpftool's perf help message, from Daniel T. Lee.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next:
selftests/bpf: Add mptcpify test
selftests/bpf: Fix error checks of mptcp open_and_load
selftests/bpf: Add two mptcp netns helpers
bpf: Add update_socket_protocol hook
bpftool: Implement link show support for xdp
bpftool: Implement link show support for tcx
selftests/bpf: Add selftest for fill_link_info
bpf: Fix uninitialized symbol in bpf_perf_link_fill_kprobe()
net: Fix slab-out-of-bounds in inet[6]_steal_sock
bpf: Document struct bpf_struct_ops fields
bpf: Support default .validate() and .update() behavior for struct_ops links
selftests/bpf: Add various more tcx test cases
selftests/bpf: Clean up fmod_ret in bench_rename test script
selftests/bpf: Fix repeat option when kfunc_call verification fails
libbpf: Set close-on-exec flag on gzopen
bpftool: fix perf help message
bpf: Remove unused declaration bpf_link_new_file()
====================
Link: https://lore.kernel.org/r/20230816212840.1539-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit 90bc21aaef4adaefceda2d385756138fc247c0c2.
Patch was merged too hastily, Vladimir requested changes in:
https://lore.kernel.org/all/20230816121305.5dio5tk3chge2ndh@skbuf/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With hardened usercopy enabled (CONFIG_HARDENED_USERCOPY=y), using the
/proc/powerpc/rtas/firmware_update interface to prepare a system
firmware update yields a BUG():
kernel BUG at mm/usercopy.c:102!
Oops: Exception in kernel mode, sig: 5 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in:
CPU: 0 PID: 2232 Comm: dd Not tainted 6.5.0-rc3+ #2
Hardware name: IBM,8408-E8E POWER8E (raw) 0x4b0201 0xf000004 of:IBM,FW860.50 (SV860_146) hv:phyp pSeries
NIP: c0000000005991d0 LR: c0000000005991cc CTR: 0000000000000000
REGS: c0000000148c76a0 TRAP: 0700 Not tainted (6.5.0-rc3+)
MSR: 8000000000029033 <SF,EE,ME,IR,DR,RI,LE> CR: 24002242 XER: 0000000c
CFAR: c0000000001fbd34 IRQMASK: 0
[ ... GPRs omitted ... ]
NIP usercopy_abort+0xa0/0xb0
LR usercopy_abort+0x9c/0xb0
Call Trace:
usercopy_abort+0x9c/0xb0 (unreliable)
__check_heap_object+0x1b4/0x1d0
__check_object_size+0x2d0/0x380
rtas_flash_write+0xe4/0x250
proc_reg_write+0xfc/0x160
vfs_write+0xfc/0x4e0
ksys_write+0x90/0x160
system_call_exception+0x178/0x320
system_call_common+0x160/0x2c4
The blocks of the firmware image are copied directly from user memory
to objects allocated from flash_block_cache, so flash_block_cache must
be created using kmem_cache_create_usercopy() to mark it safe for user
access.
Fixes: 6d07d1cd300f ("usercopy: Restrict non-usercopy caches to size 0")
Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
[mpe: Trim and indent oops]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230810-rtas-flash-vs-hardened-usercopy-v2-1-dcf63793a938@linux.ibm.com
|
|
For stack-validation of a frame-pointer build, objtool validates that
every CALL instruction is preceded by a frame-setup. The new SRSO
return thunks violate this with their RSB stuffing trickery.
Extend the __fentry__ exception to also cover the embedded_insn case
used for this. This cures:
vmlinux.o: warning: objtool: srso_untrain_ret+0xd: call without frame pointer save/setup
Fixes: 4ae68b26c3ab ("objtool/x86: Fix SRSO mess")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Link: https://lore.kernel.org/r/20230816115921.GH980931@hirez.programming.kicks-ass.net
|
|
nouveau_connector_create
We can't simply free the connector after calling drm_connector_init on it.
We need to clean up the drm side first.
It might not fix all regressions from commit 2b5d1c29f6c4
("drm/nouveau/disp: PIOR DP uses GPIO for HPD, not PMGR AUX interrupts"),
but at least it fixes a memory corruption in error handling related to
that commit.
Link: https://lore.kernel.org/lkml/20230806213107.GFZNARG6moWpFuSJ9W@fat_crate.local/
Fixes: 95983aea8003 ("drm/nouveau/disp: add connector class")
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230814144933.3956959-1-kherbst@redhat.com
|
|
'rcu-tasks.2023.07.24a', 'rcuscale.2023.07.14b', 'refscale.2023.07.14b', 'torture.2023.08.14a' and 'torturescripts.2023.07.20a' into HEAD
doc.2023.07.14b: Documentation updates.
fixes.2023.08.16a: Miscellaneous fixes.
rcu-tasks.2023.07.24a: RCU Tasks updates.
rcuscale.2023.07.14b: RCU (updater) scalability test updates.
refscale.2023.07.14b: Reference (reader) scalability test updates.
torture.2023.08.14a: Other torture-test updates.
torturescripts.2023.07.20a: Other torture-test scripting updates.
|
|
When the objects managed by rculist_nulls are allocated with
SLAB_TYPESAFE_BY_RCU, old readers may still hold references to an object
even though it is just now being added, which means the modification of
->next is visible to readers. This patch therefore uses WRITE_ONCE()
for assignments to ->next.
Signed-off-by: Alan Huang <mmpgouride@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
|
|
The rcu_nocb_poll kernel boot parameter is defined via early_param(),
whose parsing functions are invoked from parse_early_param() which
is in turn invoked by setup_arch(), which is very early indeed. It
is invoked so early that the console output timestamps read 0.000000,
in other words, before time begins.
This use of early_param() means that the rcu_nocb_poll kernel boot
parameter cannot usefully be embedded into the kernel image. Yes, you
can embed it, but setup_boot_config() is invoked from start_kernel()
too late for it to be parsed.
But it makes no sense to parse this parameter so early. After all,
it cannot do anything until the rcuog kthreads are created, which is
long after rcu_init() time, let alone setup_boot_config() time.
This commit therefore switches the rcu_nocb_poll kernel boot parameter
from early_param() to __setup(), which allows boot-config parsing of
this parameter, in turn allowing it to be embedded into the kernel image.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
|
|
The rcu_request_urgent_qs_task() function does a cross-CPU store
to ->rcu_urgent_qs, so this commit therefore marks the load in
__rcu_irq_enter_check_tick() with READ_ONCE().
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Reviewed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
|
|
This commit removes two #ifdef directives from include/linux/notifier.h
by causing SRCU Tiny to provide a dummy srcu_usage structure and a dummy
__SRCU_USAGE_INIT() macro.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Cc: Sachin Sant <sachinp@linux.ibm.com>
Cc: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
|
Since commit 4e57a4ddf6b0 ("ARM: 9107/1: syscall: always store
thread_info->abi_syscall"), the seccomp selftests "syscall_errno"
and "syscall_faked" have been broken. Both seccomp and PTRACE depend
on using the special value of "-1" for skipping syscalls. This value
wasn't working because it was getting masked by __NR_SYSCALL_MASK in
both PTRACE_SET_SYSCALL and get_syscall_nr().
Explicitly test for -1 in PTRACE_SET_SYSCALL and get_syscall_nr(),
leaving it exposed when present, allowing tracers to skip syscalls
again.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Arnd Bergmann <arnd@kernel.org>
Cc: Lecopzer Chen <lecopzer.chen@mediatek.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: linux-arm-kernel@lists.infradead.org
Fixes: 4e57a4ddf6b0 ("ARM: 9107/1: syscall: always store thread_info->abi_syscall")
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230810195422.2304827-2-keescook@chromium.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Since commit 4e57a4ddf6b0 ("ARM: 9107/1: syscall: always store
thread_info->abi_syscall"), the seccomp selftests "syscall_restart" has
been broken. This was caused by the restart syscall not being stored to
"abi_syscall" during restart setup before branching to the "local_restart"
label. Tracers would see the wrong syscall, and scno would get overwritten
while returning from the TIF_WORK path. Add the missing store.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Arnd Bergmann <arnd@kernel.org>
Cc: Lecopzer Chen <lecopzer.chen@mediatek.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: linux-arm-kernel@lists.infradead.org
Fixes: 4e57a4ddf6b0 ("ARM: 9107/1: syscall: always store thread_info->abi_syscall")
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230810195422.2304827-1-keescook@chromium.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
