| Age | Commit message (Collapse) | Author |
|---|
|
Fix the following schema warning:
gic-its@17a40000: False schema does not allow {'compatible':
['arm,gic-v3-its'], 'msi-controller': True, '#msi-cells': [[1]],
'reg': [[0, 396623872, 0, 131072]], 'status': ['disabled']}
And reorder the properties to be more in order with all other nodes.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407-topic-msm_dtb-v1-4-6efb4196f51f@linaro.org
|
|
Cheza's SPI flash hookups (qspi) are exactly the same as trogdor's.
Apply the same solution that's described in the patch ("arm64: dts:
qcom: sc7180: Fix trogdor qspi pin config")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.14.I82951106ab8170f973a4c1c7d9b034655bbe2f60@changeid
|
|
Similar to sc7180 (see the patch ("arm64: dts: qcom: sc7180: Fix
trogdor qspi pin config")), we should adjust the qspi pin config for
sc7280.
I won't re-describe all the research/arguments in the sc7180 patch
here, but there are a few differences for sc7280 worth noting:
1. On herobrine the SPI flash (qspi) is wired up differently on the
board. Rather than Cr50 and the AP being wired directly together,
there's actually a mux that will _either_ connect the AP to the
flash or Cr50 to the flash. This means that the internal pulls on
Cr50 don't affect us and we should enable our own pulldowns.
2. On herobrine, EEs added an external pulldown on the MISO line. The
argument in the schematic said that we added it (but not one on
MOSI and CLK) because Cr50 already enabled pulldowns on MOSI and
CLK. ...though, as per #1, those Cr50 pulldowns would only affect
the line when the mux was swung to Cr50.
The ironic result of #1 and #2 is that the external pulldowns on
CLK/MISO/MOSI on herobrine are _exactly opposite_ of the ones on
trogdor.
3. While I still don't have the actual exact schematics for all
variants of IDP/CRD that were produced, I have some reference
schematics that give me a belief of how the qspi is hooked up
there. From this, I'm fairly certain that all of the older variants
of IDP/CRD either have a pulldown on the CLK/MOSI/MISO lines (maybe
through a direct connect to Cr50) or have no pull (in other words,
they don't have a pullup). I'll go ahead and enable internal
pulldowns on all the lines since that won't hurt to double-pull if
there's an external pulldown and it's nice to have a pulldown if
there's nothing external. Note that this only affects _older_
CRDs. Newer revs are considered "herobrine" (see the hoglin/zoglin
device trees).
4. I didn't find the same strange "auto-switch-to-keeper" at suspend
when probing on sc7280. Whatever pulls (or lack thereof) I left at
suspend time seemed to persist into suspend.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.13.Ib44c3e417c414a4227db8def75ded37ad368212c@changeid
|
|
In commit 7ec3e67307f8 ("arm64: dts: qcom: sc7180-trogdor: add initial
trogdor and lazor dt") we specified the pull settings on the boot SPI
(the qspi) data lines as pullups to "park" the lines. This seemed like
the right thing to do, but I never really probed the lines to confirm.
Since that time, I've done A LOT of research, experiements and poking
of the lines with a voltmeter.
A first batch of discoveries:
- There is an external pullup on CS (clearly shown on schematics)
- There are weak external pulldowns on CLK/MOSI (believed to be Cr50's
internal pulldowns)
- There is no pull on MISO.
- When qspi isn't actively transferring it still drives CS, CLK, and
MOSI. CS and MOSI are driven high and CLK is driven low. It does not
drive MISO and (if no internal pulls are enabled) the line floats.
The above means that it's good to have some sort of pull on MISO, at
the very least. The pullup that we had before was actually fine (and
my voltmeter confirms that it actually affected the state of the pin)
but a pulldown would work equally well (and would match MOSI and CLK
better).
The above also means that we could save a tiny bit of power (not
measurable by my setup) by setting up a sleep state for these pins. If
nothing else this prevents us from driving high against Cr50's
internal pulldown on MOSI. However, Qualcomm has also asserted in the
past that it burns a little extra power to drive a pin, especially
since these are configured with a slightly higher drive strength
Let's fix all this. Since the external pulls are different for the two
data lines, we'll split them into separate configs. Then we'll change
the MISO pin to a pulldown and add a sleep state.
On a slightly tangental (but not totally unrelated note), I also
discovered some interesting things with these pins in suspend. First,
I found that if we don't switch the pins to GPIO that the qspi
peripheral continues to drive them in suspend. That'll be solved by
what we're already doing above. Second, I found that something in the
system suspend path (after Linux stops running) reconfigures these
pins so that they don't have their normal pulls enabled but instead
change to "keepers" (bias-bus-hold in DT speak). If a pin was floating
before we entered suspend then it would stop floating. I found that I
could manually pull a pin to a different level and then probe it and
it would stay there. This is exactly keeper behavior. With the
solution we have the switch to "keeper" doesn't matter too much but
it's good to document.
While talking about "keepers", it can also be noted that I found that
the "keepers" on these pins were at least enough to win a fight
against Cr50's internal pulls. That means it's best to make sure that
the state of the pins are already correct before the mysterious
transition to a keeper. Otherwise we'll burn (a small amount of) power
in S3 via this fight. Luckily with the current solution we don't hit
this case.
NOTE: I've left "sc7180-idp" behavior totally alone in this patch. I
didn't add a sleep state and I didn't change any pulls--I just adapted
it to the fact that the data lines have separate configs. Qualcomm
doesn't provide me with schematics for IDP and thus I don't actually
know how the pulls are configured. Since this is just a development
platform and worked well enough, it seems safer to leave it alone.
Dependencies:
- This patch has a hard dependency on ("pinctrl: qcom: Support
OUTPUT_ENABLE; deprecate INPUT_ENABLE"). Something in the boot code
seemed to have been confused and thought it needed to set the
"OUTPUT ENABLE" bit for these pins even though it was using them as
SPI. Thus if we don't honor the "output-disable" property we could
end up driving the SPI pins while in sleep mode.
- In general, it's probably best not to backport this to a kernel that
doesn't have commit d21f4b7ffc22 ("pinctrl: qcom: Avoid glitching
lines when we first mux to output"). That landed a while ago, but
it's still good to be explicit in case someone was backporting. If
we don't have that then there might be a glitch when we first switch
over to GPIO before we disable the output.
- This patch _doesn't_ really have any dependency on the qspi driver
patch that supports setting the pinctrl sleep state--they can go in
either order. If we define the sleep state and the driver never
selects it that's fine. If the driver tries to select a sleep state
that we don't define that's fine.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.12.I6f03f86546e6ce9abb1d24fd9ece663c3a5b950c@changeid
|
|
As talked about in the patch ("dt-bindings: pinctrl: qcom: tlmm should
use output-disable, not input-enable"), using "input-enable" in
pinctrl states for Qualcomm TLMM pinctrl devices was either
superfluous or there to disable a pin's output.
Looking at cheza
* ec_ap_int_l, h1_ap_int_odl: Superfluous. The pins will be configured
as inputs automatically by the Linux GPIO subsystem (presumably the
reference for other OSes using these device trees).
* bios_flash_wp_l: Superfluous. This pin is exposed to userspace
through the kernel's GPIO API and will be configured automatically.
That means that in none of the cases for cheza did we need to change
"input-enable" to "output-disable" and we can just remove these
superfluous properties.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.11.Ia439c29517b1c0625325a54387b047f099d16425@changeid
|
|
As talked about in the patch ("dt-bindings: pinctrl: qcom: tlmm should
use output-disable, not input-enable"), using "input-enable" in
pinctrl states for Qualcomm TLMM pinctrl devices was either
superfluous or there to disable a pin's output.
Looking at the sc7280-idp-ec-h1.dtsi file:
* ap_ec_int_l, h1_ap_int_odl: Superfluous. The pins will be configured
as inputs automatically by the Linux GPIO subsystem (presumably the
reference for other OSes using these device trees).
That means that in none of the cases for sc7280-idp-ec-h1.dtsi did we
need to change "input-enable" to "output-disable" and we can just
remove these superfluous properties.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.10.I1343c20f4aaac8e2c1918b756f7ed66f6ceace9c@changeid
|
|
As talked about in the patch ("dt-bindings: pinctrl: qcom: tlmm should
use output-disable, not input-enable"), using "input-enable" in
pinctrl states for Qualcomm TLMM pinctrl devices was either
superfluous or there to disable a pin's output.
Looking at trogdor:
* ap_ec_int_l, fp_to_ap_irq_l, h1_ap_int_odl, p_sensor_int_l:
Superfluous. The pins will be configured as inputs automatically by
the Linux GPIO subsystem (presumably the reference for other OSes
using these device trees).
* bios_flash_wp_l: Superfluous. This pin is exposed to userspace
through the kernel's GPIO API and will be configured automatically.
That means that in none of the cases for trogdor did we need to change
"input-enable" to "output-disable" and we can just remove these
superfluous properties.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.9.I94dbc53176e8adb0d7673b7feb2368e85418f938@changeid
|
|
The l13a rail on trogdor devices has always been intended to be
always-on on both S0 and S3. Different trogdor variants use l13a in
slightly different ways, but the overall theme is that it's a 1.8V
rail that the board uses for things that it wants powered in on S0 and
S3. On many boards this includes the boot SPI (AKA qspi).
For all intents and purposes this patch is actually a no-op since
something else in the system seems to already be keeping the rail on
all the time (confirmed via multimeter). That "something else" was
postulated to be the modem but the rail is on / stays on even without
the modem/wifi coming up so it's likely the boot config. In any case,
making the fact that this is always-on explicit seems like a good
idea.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.4.I9f47a8a53eacff6229711a827993792ceeb36971@changeid
|
|
There are 4 qspi data pins: data0, data1, data2, and data3. Currently
we have a shared pin state for data0 and data1 (2 lane config) and a
pin state for data2 and data3 (you'd enable both this and the 2 lane
state for 4 lanes). The second state is obviously misnamed. Fix it.
Fixes: e1ce853932b7 ("arm64: dts: qcom: sdm845: Add qspi (quad SPI) node")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.3.I88528d037b7fda4e53a40f661be5ac61628691cd@changeid
|
|
There are 4 qspi data pins: data0, data1, data2, and data3. Currently
we have a shared pin state for data0 and data1 (2 lane config) and a
pin state for data2 and data3 (you'd enable both this and the 2 lane
state for 4 lanes). The second state is obviously misnamed. Fix it.
Fixes: 7720ea001b52 ("arm64: dts: qcom: sc7280: Add QSPI node")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.2.I4043491bb24b1e92267c5033d76cdb0fe60934da@changeid
|
|
There are 4 qspi data pins: data0, data1, data2, and data3. Currently
we have a shared pin state for data0 and data1 (2 lane config) and a
pin state for data2 and data3 (you'd enable both this and the 2 lane
state for 4 lanes). The second state is obviously misnamed. Fix it.
Fixes: ba3fc6496366 ("arm64: dts: sc7180: Add qupv3_0 and qupv3_1")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.1.Ifc1b5be04653f4ab119698a5944bfecded2080d6@changeid
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl into arm64-for-6.4
Merge the support for output-enable/disable in the pinctrl-msm driver,
to ensure that bisection across the following SC7180/SC7280 DeviceTree
changes result in something electrically sound.
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add initial device tree support for Qualcomm IPQ9574 SoC and AL02 board
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Co-developed-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com>
Signed-off-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230316072940.29137-6-quic_devipriy@quicinc.com
|
|
Merge the IPQ9574 Global Clock Controller Devicetree binding, to make
available the clock definitions used in the Devicetree source.
|
|
Enables clk & pinctrl related configs for Qualcomm IPQ9574 SoC
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230316072940.29137-7-quic_devipriy@quicinc.com
|
|
Add clock and reset ID definitions for ipq9574
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230316072940.29137-2-quic_devipriy@quicinc.com
|
|
This fixes memory overlap error:
[ 0.000000] reserved@6300000 (0x0000000006300000--0x0000000007000000) overlaps with smem_region@6a00000 (0x0000000006a00000--0x0000000006c00000)
smem_region is the same as in downstream (qcom,smem) [1], therefore
split reserved memory into two sections on either side of smem_region.
Not adding labels as it's not expected to be used.
[1] https://android.googlesource.com/kernel/msm/+/refs/heads/android-msm-angler-3.10-marshmallow-mr1/arch/arm/boot/dts/qcom/msm8994.dtsi#948
Fixes: 380cd3a34b7f ("arm64: dts: msm8994-angler: fix the memory map")
Signed-off-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230131200414.24373-3-pvorel@suse.cz
|
|
Angler's cont_splash_mem mapping is shorter in downstream [1],
therefore 380cd3a34b7f was wrong. Obviously also 0e5ded926f2a was wrong
(workaround which fixed booting at the time).
This fixes error:
[ 0.000000] memory@3401000 (0x0000000003401000--0x0000000005601000) overlaps with tzapp@4800000 (0x0000000004800000--0x0000000006100000)
[1] https://android.googlesource.com/kernel/msm/+/refs/heads/android-msm-angler-3.10-marshmallow-mr1/arch/arm64/boot/dts/huawei/huawei_msm8994_angler_row_vn1/huawei-fingerprint.dtsi#16
Fixes: 380cd3a34b7f ("arm64: dts: msm8994-angler: fix the memory map")
Fixes: 0e5ded926f2a ("arm64: dts: qcom: msm8994-angler: Disable cont_splash_mem")
Signed-off-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230131200414.24373-2-pvorel@suse.cz
|
|
Developers on the ChromeOS team generally want to be notified to
review changes that affect Chromebook device tree files. While we
could individually add developers, the set of developers and the time
each one has available to review patches will change over time. Let's
try adding a group list as a reviewer and see if that's an effective
way to manage things.
A few notes:
* Though this email address is actually backed by a mailing list, I'm
adding it as "R"eviewer and not "L"ist since it's not a publicly
readable mailing list and it's intended just to have a few people on
it. This also hopefully conveys a little more responisbility for the
people that are part of this group.
* I've added all sc7180 and sc7280 files here. At the moment I'm not
aware of any non-Chromebooks being supported that use these
chips. If later something shows up then we can try to narrow down.
* I've added "sdm845-cheza" to this list but not the rest of
"sdm845". Cheza never shipped but some developers still find the old
developer boards useful and thus it continues to get minimal
maintenance. Most sdm845 device tree work, however, seems to be for
non-Chromebooks.
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230330141051.1.If8eb4f30cb53a00a5bef1b7d3cc645c3536615ec@changeid
|
|
The caller of the function thermal_zone_device_register_with_trips()
can pass a thermal_zone_params structure parameter.
This one is used by the thermal core code until the thermal zone is
destroyed. That forces the caller, so the driver, to keep the pointer
valid until it unregisters the thermal zone if we want to make the
thermal zone device structure private the core code.
As the thermal zone device structure would be private, the driver can
not access to thermal zone device structure to retrieve the tzp field
after it passed it to register the thermal zone.
So instead of forcing the users of the function to deal with the tzp
structure life cycle, make the usage easier by allocating our own
thermal zone params, copying the parameter content and by freeing at
unregister time. The user can then create the parameters on the stack,
pass it to the registering function and forget about it.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230404075138.2914680-3-daniel.lezcano@linaro.org
|
|
The functions thermal_of_zone_register() and
thermal_of_zone_unregister() are no longer needed from the drivers as
the devm_ variant is always used.
Make them static in the C file and remove their declaration from thermal.h
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230404075138.2914680-2-daniel.lezcano@linaro.org
|
|
The driver is using the devm_thermal_of_zone_device_register().
In the error path of the function calling
devm_thermal_of_zone_device_register(), the function
devm_thermal_of_zone_unregister() should be called instead of
thermal_of_zone_unregister(), otherwise this one will be called twice
when the device is freed.
The same happens for the remove function where the devm_ guarantee the
thermal_of_zone_unregister() will be called, so adding this call in
the remove function will lead to a double free also.
Use devm_ variant in the error path of the probe function.
Remove thermal_of_zone_unregister() in the remove function.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230404075138.2914680-1-daniel.lezcano@linaro.org
|
|
Similar to the existing reg_downshift mechanism, that is used to
translate register addresses on busses that have a smaller address
stride, it's also possible to want to upshift register addresses.
Such a case was encountered when network PHYs and PCS that usually sit
on a MDIO bus (16-bits register with a stride of 1) are integrated
directly as memory-mapped devices. Here, the same register layout
defined in 802.3 is used, but the register now have a larger stride.
Introduce a mechanism to also allow upshifting register addresses.
Re-purpose reg_downshift into a more generic, signed reg_shift, whose
sign indicates the direction of the shift. To avoid confusion, also
introduce macros to explicitly indicate if we want to downshift or
upshift.
For bisectability, change any use of reg_downshift to use reg_shift.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/20230407152604.105467-1-maxime.chevallier@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There are some interop issues seen across a few DP monitors with
HBR3 and herobrine boards where the DP display stays blank with hbr3.
This is still under investigation but in preparation for supporting
higher resolutions, its better to disable HBR3 till the issues are
root-caused as there is really no guarantee which monitors will show
the issue and which would not.
This can be enabled back after successful validation across more DP
sinks.
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230329233416.27152-1-quic_abhinavk@quicinc.com
|
|
RSC v3 register offsets are same for all minor versions of v3. Fix a
minor version check to pick correct offsets for all v3 minor versions.
Fixes: 40482e4f7364 ("soc: qcom: rpmh-rsc: Add support for RSC v3 register offsets")
Signed-off-by: Tushar Nimkar <quic_tnimkar@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406115732.9293-1-quic_tnimkar@quicinc.com
|
|
The VLAN filters info is currently being held in a list and 2 bitmaps
(active_cvlans and active_svlans). We are experiencing some racing where
data is not in sync in the list and bitmaps. For example, the VLAN is
initially added to the list but only when the PF replies, it is added to
the bitmap. If a user adds many V2 VLANS before the PF responds:
while [ $((i++)) ]
ip l add l eth0 name eth0.$i type vlan id $i
we might end up with more VLAN list entries than the designated limit.
Also, The "ip link show" will show more links added than the PF limit.
On the other and, the bitmaps are only used to check the number of VLAN
filters and to re-enable the filters when the interface goes from DOWN to
UP.
This patch gets rid of the bitmaps and uses the list only. To do that,
the states of the VLAN filter are modified:
1 - IAVF_VLAN_REMOVE: the entry needs to be totally removed after informing
the PF. This is the "ip link del eth0.$i" path.
2 - IAVF_VLAN_DISABLE: (new) the netdev went down. The filter needs to be
removed from the PF and then marked INACTIVE.
3 - IAVF_VLAN_INACTIVE: (new) no PF filter exists, but the user did not
delete the VLAN.
Fixes: 48ccc43ecf10 ("iavf: Add support VIRTCHNL_VF_OFFLOAD_VLAN_V2 during netdev config")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The VLAN filter states are currently being saved as individual bits.
This is error prone as multiple bits might be mistakenly set.
Fix by replacing the bits with a single state enum. Also, add an
"ACTIVE" state for filters that are accepted by the PF.
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
HWmon core receives an array of pointers to hwmon_channel_info and it
does not modify it, thus it can be array of const pointers for safety.
This allows drivers to make them also const.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The DSA framework has got more picky about always having a phy-mode
for the CPU port. The SoC Ethernet is being configured to
10gbase-r. Set the switch phy-mode based on this. Additionally, the
SoC Ethernet is using in-band signalling to determine the link speed,
so add same parameter to the switch.
Additionally, the cpu label has never actually been used in the
binding, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The DSA framework has got more picky about always having a phy-mode
for the CPU port. The Armada Ethernet supports RGMII, SGMII,
1000base-x and 2500Base-X. Set the switch phy-mode based on how the
SoC Ethernet ports is been configured. For RGMII mode, have the switch
add the delays.
Additionally, the cpu label has never actually been used in the
binding, so remove it.
Lastly, add a fixed-link node indicating the expected speed/duplex of
the link to the SoC.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The DSA framework has got more picky about always having a phy-mode
for the CPU port. The Orion5x Ethernet is an RGMII port. Set the
switch to impose the RGMII delays.
Additionally, the cpu label has never actually been used in the
binding, so remove it.
Lastly, add a fixed-link node indicating the expected speed/duplex of
the link to the SoC.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The DSA framework has got more picky about always having a phy-mode
for the CPU port. The Kirkwood Ethernet is an RGMII port. Set the
switch to impose the RGMII delays.
Additionally, the cpu label has never actually been used in the
binding, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The GL-MV1000 (Brume) is a small form-factor gateway router.
It is based on the Marvell Armada 88F3720 SOC (1GHz), has 3 gigabit ethernet ports, 1 GB RAM, 16M SPI flash, 8GB eMMC and an uSD slot, as well as an USB 2.0 type A and an USB 3.0 type C port.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
CC: Pali <pali@kernel.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Since commit ee6d3dd4ed48 ("driver core: make kobj_type constant.")
the driver core allows the usage of const struct kobj_type.
Take advantage of this to constify the structure definition to prevent
modification at runtime.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Bindings expect thermal node names to end with '-thermal':
armada-8040-db.dtb: thermal-zones: 'ap-thermal-cpu0', ... do not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Armada 7040 uses a rather small 15MB memory window for every PCI adapter,
however this is not sufficient for Qualcomm QCA6390 802.11ax cards that
are shipped along with the OpenWrt WLAN model of MOCHAbin as ath11k
requires at least 16MB of memory.
So, similar to what MACCHIATOBin has been doing for years, lets move
to using the second PCIe 2 memory window and expand it to 128MB to
make it future proof.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Make Intel uncore frequency driver support to client processor starting
from Alder Lake.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20230330145939.1022261-1-srinivas.pandruvada@linux.intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The detection of atomic update failure in reserve_eilvt_offset() is
not correct. The value returned by atomic_cmpxchg() should be compared
to the old value from the location to be updated.
If these two are the same, then atomic update succeeded and
"eilvt_offsets[offset]" location is updated to "new" in an atomic way.
Otherwise, the atomic update failed and it should be retried with the
value from "eilvt_offsets[offset]" - exactly what atomic_try_cmpxchg()
does in a correct and more optimal way.
Fixes: a68c439b1966c ("apic, x86: Check if EILVT APIC registers are available (AMD only)")
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/20230227160917.107820-1-ubizjak@gmail.com
|
|
Assignments from pointer variables of type (void *) do not require
explicit type casts, so remove such type cases from the code in
drivers/base/power/main.c where applicable.
Signed-off-by: Li zeming <zeming@nfschina.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since the cpufreq core directly uses freq_table, for cpufreq drivers
that set their target_index() callback, make it mandatory for them to
set the same.
Since this is set per policy and normally from policy->init(), do this
from cpufreq_table_validate_and_sort() which gets called right after
->init().
Reported-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The driver doesn't use simple-KMS helpers to set a simple display pipeline
but only the drm_simple_encoder_init() function to initialize an encoder.
That helper is just a wrapper of drm_encoder_init(), but passing a struct
drm_encoder_funcs that sets the .destroy handler to drm_encoder_cleanup().
Since the <drm/drm_simple_kms_helper.h> header is only included for this
helper and because the connector is initialized with drm_connector_init()
as well, do the same for the encoder and drop the header include.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230406110235.3092055-3-javierm@redhat.com
|
|
This helper is just a wrapper that calls drm_connector_cleanup(), there's
no need to have another level of indirection.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230406110235.3092055-2-javierm@redhat.com
|
|
Add MT8195 AP Domain support to LVTS Driver.
Take the opportunity to update the comments to show calibration data
information related to the new domain.
[dlezcano]: Massaged a bit the changelog
Signed-off-by: Balsam CHIHI <bchihi@baylibre.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230307154524.118541-3-bchihi@baylibre.com
|
|
for mt8195
Add AP Domain to LVTS thermal controllers dt-binding definition for mt8195.
Signed-off-by: Balsam CHIHI <bchihi@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230307154524.118541-2-bchihi@baylibre.com
|
|
Replace the open-code with dev_err_probe() to simplify the code.
Signed-off-by: Ye Xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/202303241020110014476@zte.com.cn
|
|
The binary representation for sensor 1 interrupt status was incorrectly
assembled, when compared to the full table given in the same comment
section. The conversion into hex was also incorrect, leading to
incorrect interrupt status bitmask for sensor 1. This would cause the
driver to incorrectly identify changes for sensor 1, when in fact it
was sensor 0, or a sensor access time out.
Fix the binary and hex representations in the comments, and the actual
bitmask macro.
Fixes: f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230328031017.1360976-1-wenst@chromium.org
|
|
Commit 32a7a02117de ("thermal/core: Relocate the traces definition in
thermal directory") moves include/trace/events/thermal_power_allocator.h to
drivers/thermal/thermal_trace_ipa.h, but misses to adjust the file
entry for the THERMAL/POWER_ALLOCATOR section.
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about a
broken reference.
Adjust this file entry in THERMAL/POWER_ALLOCATOR.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230328091737.6785-1-lukas.bulwahn@gmail.com
|
|
Cleanup bindings dropping unneeded quotes. Once all these are fixed,
checking for this can be enabled in yamllint.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230327170233.4109156-1-robh@kernel.org
|
|
Remove struct thermal_bind_params because no one is using it for thermal
binding now.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230330104526.3196-1-rui.zhang@intel.com
|
|
Thermal zones located in power domains may not be accessible when
the domain is powergated. In this situation, reading the temperature
will return -BPMP_EFAULT. When evaluating trips, BPMP will internally
use -256C as the temperature for offline zones.
For smooth operation, for offline zones, return -EAGAIN when reading
the temperature and allow registration of zones even if they are
offline during probe.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20230330094904.2589428-1-cyndis@kapsi.fi
|
