| Age | Commit message (Collapse) | Author |
|---|
|
Add mclk-fs support to audio graph card
as initially supported in simple card.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The main rt5514 driver optionally calls into the SPI back-end to load
the firmware. This causes a link error when one driver selects rt5514
as built-in and another driver selects rt5514-spi as a loadable module:
sound/soc/codecs/rt5514.o: In function `rt5514_dsp_voice_wake_up_put':
rt5514.c:(.text+0xac8): undefined reference to `rt5514_spi_burst_write'
As a workaround, this adds another silent symbol, to force rt5514-spi
to be built-in for that configuration. I'm not overly happy with
that solution, but couldn't come up with anything better. Using
'IS_REACHABLE()' would break the case that relies on the loadable
module, and all other ideas would result in more complexity.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The new functions are only used when CONFIG_PM is enabled,
leading to a harmless warning:
sound/soc/codecs/rt5514-spi.c:474:12: error: 'rt5514_resume' defined but not used [-Werror=unused-function]
sound/soc/codecs/rt5514-spi.c:464:12: error: 'rt5514_suspend' defined but not used [-Werror=unused-function]
This marks them as __maybe_unused to make the build silent
again.
Fixes: 58f1c07d23cd ("ASoC: rt5514: Voice wakeup support.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Previously, cache blocks were being allocated in reverse order. Fix
this by pulling the block off the head of the free list.
Shouldn't have any impact on performance or latency but it is more
correct to have the cache blocks allocated/mapped in ascending order.
This fix will slightly increase the chances of two adjacent oblocks
being in adjacent cblocks.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
10240 blocks was too much, lowering this reduces the latency of copying
and consumes less memory.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
issued at once
On large systems the cache policy can be over enthusiastic and queue far
too much dirty data to be written back. This consumes memory.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
writebacks
If the origin device is idle try and writeback more data.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
The background_tracker holds a set of promotions/demotions that the
cache policy wishes the core target to implement.
When adding a new operation to the tracker it's possible that an
operation on the same block is already present (but in practise this
doesn't appear to be happening). Catch these situations and do the
appropriate cleanup.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Requesting a sync on an active raid device via a table reload
(see 'sync' parameter in Documentation/device-mapper/dm-raid.txt)
skips the super_load() call that defines the superblock size
(rdev->sb_size) -- resulting in an oops if/when super_sync()->memset()
is called.
Fix by moving the initialization of the superblock start and size
out of super_load() to the caller (analyse_superblocks).
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
When slub_debug is enabled kmalloc returns unaligned memory. XFS uses
this unaligned memory for its buffers (if an unaligned buffer crosses a
page, XFS frees it and allocates a full page instead - see the function
xfs_buf_allocate_memory).
dm-integrity checks if bv_offset is aligned on page size and this check
fail with slub_debug and XFS.
Fix this bug by removing the bv_offset check, leaving only the check for
bv_len.
Fixes: 7eada909bfd7 ("dm: add integrity target")
Cc: stable@vger.kernel.org # v4.12+
Reported-by: Bruno Prémont <bonbons@sysophe.eu>
Reviewed-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
When slub_debug is enabled kmalloc returns unaligned memory. XFS uses
this unaligned memory for its buffers (if an unaligned buffer crosses a
page, XFS frees it and allocates a full page instead - see the function
xfs_buf_allocate_memory).
dm-crypt checks if bv_offset is aligned on page size and these checks
fail with slub_debug and XFS.
Fix this bug by removing the bv_offset checks. Switch to checking if
bv_len is aligned instead of bv_offset (this check should be sufficient
to prevent overruns if a bio with too small bv_len is received).
Fixes: 8f0009a22517 ("dm crypt: optionally support larger encryption sector size")
Cc: stable@vger.kernel.org # v4.12+
Reported-by: Bruno Prémont <bonbons@sysophe.eu>
Tested-by: Bruno Prémont <bonbons@sysophe.eu>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Makes dm_get_md() and dm_get_from_kobject() have similar code.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
The following BUG_ON was hit when testing repeat creation and removal of
DM devices:
kernel BUG at drivers/md/dm.c:2919!
CPU: 7 PID: 750 Comm: systemd-udevd Not tainted 4.1.44
Call Trace:
[<ffffffff81649e8b>] dm_get_from_kobject+0x34/0x3a
[<ffffffff81650ef1>] dm_attr_show+0x2b/0x5e
[<ffffffff817b46d1>] ? mutex_lock+0x26/0x44
[<ffffffff811df7f5>] sysfs_kf_seq_show+0x83/0xcf
[<ffffffff811de257>] kernfs_seq_show+0x23/0x25
[<ffffffff81199118>] seq_read+0x16f/0x325
[<ffffffff811de994>] kernfs_fop_read+0x3a/0x13f
[<ffffffff8117b625>] __vfs_read+0x26/0x9d
[<ffffffff8130eb59>] ? security_file_permission+0x3c/0x44
[<ffffffff8117bdb8>] ? rw_verify_area+0x83/0xd9
[<ffffffff8117be9d>] vfs_read+0x8f/0xcf
[<ffffffff81193e34>] ? __fdget_pos+0x12/0x41
[<ffffffff8117c686>] SyS_read+0x4b/0x76
[<ffffffff817b606e>] system_call_fastpath+0x12/0x71
The bug can be easily triggered, if an extra delay (e.g. 10ms) is added
between the test of DMF_FREEING & DMF_DELETING and dm_get() in
dm_get_from_kobject().
To fix it, we need to ensure the test of DMF_FREEING & DMF_DELETING and
dm_get() are done in an atomic way, so _minor_lock is used.
The other callers of dm_get() have also been checked to be OK: some
callers invoke dm_get() under _minor_lock, some callers invoke it under
_hash_lock, and dm_start_request() invoke it after increasing
md->open_count.
Cc: stable@vger.kernel.org
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
The structure srcu_struct can be very big, its size is proportional to the
value CONFIG_NR_CPUS. The Fedora kernel has CONFIG_NR_CPUS 8192, the field
io_barrier in the struct mapped_device has 84kB in the debugging kernel
and 50kB in the non-debugging kernel. The large size may result in failure
of the function kzalloc_node.
In order to avoid the allocation failure, we use the function
kvzalloc_node, this function falls back to vmalloc if a large contiguous
chunk of memory is not available. This patch also moves the field
io_barrier to the last position of struct mapped_device - the reason is
that on many processor architectures, short memory offsets result in
smaller code than long memory offsets - on x86-64 it reduces code size by
320 bytes.
Note to stable kernel maintainers - the kernels 4.11 and older don't have
the function kvzalloc_node, you can use the function vzalloc_node instead.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
The SCSI layer allows ZBC drives to have a smaller last runt zone. For
such a device, specifying the entire capacity for a dm-zoned target
table entry fails because the specified capacity is not aligned on a
device zone size indicated in the request queue structure of the
device.
Fix this problem by ignoring the last runt zone in the entry length
when seting up the dm-zoned target (ctr method) and when iterating table
entries of the target (iterate_devices method). This allows dm-zoned
users to still easily setup a target using the entire device capacity
(as mandated by dm-zoned) or the aligned capacity excluding the last
runt zone.
While at it, replace direct references to the device queue chunk_sectors
limit with calls to the accessor blk_queue_zone_sectors().
Reported-by: Peter Desnoyers <pjd@ccs.neu.edu>
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Using the ARRAY_SIZE macro improves the readability of the code.
Found with Coccinelle with the following semantic patch:
@r depends on (org || report)@
type T;
T[] E;
position p;
@@
(
(sizeof(E)@p /sizeof(*E))
|
(sizeof(E)@p /sizeof(E[...]))
|
(sizeof(E)@p /sizeof(T))
)
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Now that we have the ability log filesystem writes using a flat buffer, add
support for DAX.
The motivation for this support is the need for an xfstest that can test
the new MAP_SYNC DAX flag. By logging the filesystem activity with
dm-log-writes we can show that the MAP_SYNC page faults are writing out
their metadata as they happen, instead of requiring an explicit
msync/fsync.
Unfortunately we can't easily track data that has been written via
mmap() now that the dax_flush() abstraction was removed by commit
c3ca015fab6d ("dax: remove the pmem_dax_ops->flush abstraction").
Otherwise we could just treat each flush as a big write, and store the
data that is being synced to media. It may be worthwhile to add the
dax_flush() entry point back, just as a notifier so we can do this
logging.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Currently dm-log-writes supports writing filesystem data via BIOs, and
writing internal metadata from a flat buffer via write_metadata().
For DAX writes, though, we won't have a BIO, but will instead have an
iterator that we'll want to use to fill a flat data buffer.
So, create write_inline_data() which allows us to write filesystem data
using a flat buffer as a source, and wire it up in log_one_block().
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
There is only one per_bio_data size now that writethrough-specific data
was removed from the per_bio_data structure.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Now that the writethrough code is much simpler there is no need to track
so much state or cascade bio submission (as was done, via
writethrough_endio(), to issue origin then cache IO in series).
As such the obsolete writethrough list and workqueue is also removed.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Discontinue issuing writethrough write IO in series to the origin and
then cache.
Use bio_clone_fast() to create a new origin clone bio that will be
mapped to the origin device and then bio_chain() it to the bio that gets
remapped to the cache device. The origin clone bio does _not_ have a
copy of the per_bio_data -- as such check_if_tick_bio_needed() will not
be called.
The cache bio (parent bio) will not complete until the origin bio has
completed -- this fulfills bio_clone_fast()'s requirements as well as
the requirement to not complete the original IO until the write IO has
completed to both the origin and cache device.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
No functional changes, just a bit cleaner than passing cache_features
structure.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
When a DM cache in writeback mode moves data between the slow and fast
device it can often avoid a copy if the triggering bio either:
i) covers the whole block (no point copying if we're about to overwrite it)
ii) the migration is a promotion and the origin block is currently discarded
Prior to this fix there was a race with case (ii). The discard status
was checked with a shared lock held (rather than exclusive). This meant
another bio could run in parallel and write data to the origin, removing
the discard state. After the promotion the parallel write would have
been lost.
With this fix the discard status is re-checked once the exclusive lock
has been aquired. If the block is no longer discarded it falls back to
the slower full copy path.
Fixes: b29d4986d ("dm cache: significant rework to leverage dm-bio-prison-v2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Pull KVM fix from Radim Krčmář:
"Fix PPC HV host crash that can occur as a result of resizing the guest
hashed page table"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Book3S HV: Fix exclusion between HPT resizing and other HPT updates
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS fixes from James Hogan:
"A final few MIPS fixes for 4.14:
- fix BMIPS NULL pointer dereference (4.7)
- fix AR7 early GPIO init allocation failure (3.19)
- fix dead serial output on certain AR7 platforms (2.6.35)"
* tag 'mips_fixes_4.14_2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
MIPS: AR7: Ensure that serial ports are properly set up
MIPS: AR7: Defer registration of GPIO
MIPS: BMIPS: Fix missing cbr address
|
|
Following my recent transition from Imagination Technologies to the=20
reincarnated MIPS company add a .mailmap mapping for my work address,
so that `scripts/get_maintainer.pl' gets it right for past commits.
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When bitmap is resized, the old kalloced chunks just are not released
once the resized bitmap starts to use new space.
This fixes in particular kmemleak reports like this one:
unreferenced object 0xffff8f4311e9c000 (size 4096):
comm "lvm", pid 19333, jiffies 4295263268 (age 528.265s)
hex dump (first 32 bytes):
02 80 02 80 02 80 02 80 02 80 02 80 02 80 02 80 ................
02 80 02 80 02 80 02 80 02 80 02 80 02 80 02 80 ................
backtrace:
[<ffffffffa69471ca>] kmemleak_alloc+0x4a/0xa0
[<ffffffffa628c10e>] kmem_cache_alloc_trace+0x14e/0x2e0
[<ffffffffa676cfec>] bitmap_checkpage+0x7c/0x110
[<ffffffffa676d0c5>] bitmap_get_counter+0x45/0xd0
[<ffffffffa676d6b3>] bitmap_set_memory_bits+0x43/0xe0
[<ffffffffa676e41c>] bitmap_init_from_disk+0x23c/0x530
[<ffffffffa676f1ae>] bitmap_load+0xbe/0x160
[<ffffffffc04c47d3>] raid_preresume+0x203/0x2f0 [dm_raid]
[<ffffffffa677762f>] dm_table_resume_targets+0x4f/0xe0
[<ffffffffa6774b52>] dm_resume+0x122/0x140
[<ffffffffa6779b9f>] dev_suspend+0x18f/0x290
[<ffffffffa677a3a7>] ctl_ioctl+0x287/0x560
[<ffffffffa677a693>] dm_ctl_ioctl+0x13/0x20
[<ffffffffa62d6b46>] do_vfs_ioctl+0xa6/0x750
[<ffffffffa62d7269>] SyS_ioctl+0x79/0x90
[<ffffffffa6956d41>] entry_SYSCALL_64_fastpath+0x1f/0xc2
Signed-off-by: Zdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
Patch fixes kmemleak on md_stop() path used likely only by dm-raid wrapper.
Code of md is using mddev_put() where both bitsets are released however this
freeing is not shared.
Also set NULL to bio_set and sync_set pointers just like mddev_put is
doing.
Signed-off-by: Zdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
This reverts commit 941f5f0f6ef5338814145cf2b813cf1f98873e2f.
Sadly, it turns out that we really can't just do the cross-CPU IPI to
all CPU's to get their proper frequencies, because it's much too
expensive on systems with lots of cores.
So we'll have to revert this for now, and revisit it using a smarter
model (probably doing one system-wide IPI at open time, and doing all
the frequency calculations in parallel).
Reported-by: WANG Chao <chao.wang@ucloud.cn>
Reported-by: Ingo Molnar <mingo@kernel.org>
Cc: Rafael J Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114761
Addresses-Coverity-ID: 114762
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114763
Addresses-Coverity-ID: 114764
Addresses-Coverity-ID: 114765
Addresses-Coverity-ID: 114766
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114767
Addresses-Coverity-ID: 114768
Addresses-Coverity-ID: 114769
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
We have to unlock before returning if input_allocate_device() fails.
Fixes: 04ce40a61a91 ("Input: uinput - remove uinput_allocate_device()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The S6SY761 touchscreen is a capicitive multi-touch controller
for mobile use. It's connected with i2c at the address 0x48.
This commit provides a basic version of the driver which can
handle only initialization, touch events and power states.
The controller is controlled by a firmware which, in the version
I currently have, doesn't provide all the possible
functionalities mentioned in the datasheet.
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The HiDeep touchscreen device is a capacitive multi-touch controller
mainly for multi-touch supported devices use. It use I2C interface for
communication to IC and provide axis X, Y, Z locations for ten finger
touch through input event interface to userspace.
It support the Crimson and the Lime two type IC. They are different
the number of channel supported and FW size. But the working protocol
is same.
Signed-off-by: Anthony Kim <anthony.kim@hideep.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"Last few patches to wrap up.
Two i915 fixes that are on their way to stable, one vmware black
screen bug, and one const patch that I was going to drop, but it was
clearly a pretty safe one liner"
* tag 'drm-fixes-for-v4.14-rc9' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Deconstruct struct sgt_dma initialiser
drm/i915: Reject unknown syncobj flags
drm/vmwgfx: Fix Ubuntu 17.10 Wayland black screen issue
drm/vmwgfx: constify vmw_fence_ops
|
|
The file arch/s390/include/uapi/asm/virtio-ccw.h belongs to the
s390 virtio drivers as well.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Rebooting into a new kernel with kexec fails (system dies) if tried on
a machine that has no-execute support. Reason for this is that the so
called datamover code gets executed with DAT on (MMU is active) and
the page that contains the datamover is marked as non-executable.
Therefore when branching into the datamover an unexpected program
check happens and afterwards the machine is dead.
This can be simply avoided by disabling DAT, which also disables any
no-execute checks, just before the datamover gets executed.
In fact the first thing done by the datamover is to disable DAT. The
code in the datamover that disables DAT can be removed as well.
Thanks to Michael Holzheu and Gerald Schaefer for tracking this down.
Reviewed-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Reviewed-by: Philipp Rudo <prudo@linux.vnet.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fixes: 57d7f939e7bd ("s390: add no-execute support")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Dan Horák reported the following crash related to transactional execution:
User process fault: interruption code 0013 ilc:3 in libpthread-2.26.so[3ff93c00000+1b000]
CPU: 2 PID: 1 Comm: /init Not tainted 4.13.4-300.fc27.s390x #1
Hardware name: IBM 2827 H43 400 (z/VM 6.4.0)
task: 00000000fafc8000 task.stack: 00000000fafc4000
User PSW : 0705200180000000 000003ff93c14e70
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:1 AS:0 CC:2 PM:0 RI:0 EA:3
User GPRS: 0000000000000077 000003ff00000000 000003ff93144d48 000003ff93144d5e
0000000000000000 0000000000000002 0000000000000000 000003ff00000000
0000000000000000 0000000000000418 0000000000000000 000003ffcc9fe770
000003ff93d28f50 000003ff9310acf0 000003ff92b0319a 000003ffcc9fe6d0
User Code: 000003ff93c14e62: 60e0b030 std %f14,48(%r11)
000003ff93c14e66: 60f0b038 std %f15,56(%r11)
#000003ff93c14e6a: e5600000ff0e tbegin 0,65294
>000003ff93c14e70: a7740006 brc 7,3ff93c14e7c
000003ff93c14e74: a7080000 lhi %r0,0
000003ff93c14e78: a7f40023 brc 15,3ff93c14ebe
000003ff93c14e7c: b2220000 ipm %r0
000003ff93c14e80: 8800001c srl %r0,28
There are several bugs with control register handling with respect to
transactional execution:
- on task switch update_per_regs() is only called if the next task has
an mm (is not a kernel thread). This however is incorrect. This
breaks e.g. for user mode helper handling, where the kernel creates
a kernel thread and then execve's a user space program. Control
register contents related to transactional execution won't be
updated on execve. If the previous task ran with transactional
execution disabled then the new task will also run with
transactional execution disabled, which is incorrect. Therefore call
update_per_regs() unconditionally within switch_to().
- on startup the transactional execution facility is not enabled for
the idle thread. This is not really a bug, but an inconsistency to
other facilities. Therefore enable the facility if it is available.
- on fork the new thread's per_flags field is not cleared. This means
that a child process inherits the PER_FLAG_NO_TE flag. This flag can
be set with a ptrace request to disable transactional execution for
the current process. It should not be inherited by new child
processes in order to be consistent with the handling of all other
PER related debugging options. Therefore clear the per_flags field in
copy_thread_tls().
Reported-and-tested-by: Dan Horák <dan@danny.cz>
Fixes: d35339a42dd1 ("s390: add support for transactional memory")
Cc: <stable@vger.kernel.org> # v3.7+
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
Make use of the "stack_depth" tracking feature introduced with
commit 8726679a0fa31 ("bpf: teach verifier to track stack depth") for the
s390 JIT, so that stack usage can be reduced.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/vfio-ccw into features
Pull vfio-ccw update from Cornelia Huck:
"A vfio-ccw bugfix: avoid freeing that which should not be freed."
|
|
Arnd reported the following build bug bug:
In file included from arch/arm/mach-sa1100/simpad.c:20:0:
arch/arm/mach-sa1100/include/mach/SA-1100.h:1118:18: error: large
integer implicitly truncated to unsigned type [-Werror=overflow]
(0x00000001 << (Nb))
^
include/linux/gpio/machine.h:56:16: note: in definition of macro
'GPIO_LOOKUP_IDX'
.chip_hwnum = _chip_hwnum,
^~~~~~~~~~~
arch/arm/mach-sa1100/include/mach/SA-1100.h:1140:21: note: in
expansion of macro 'GPIO_GPIO'
^~~~~~~~~
arch/arm/mach-sa1100/simpad.c:331:27: note: in expansion of
macro 'GPIO_GPIO21'
GPIO_LOOKUP_IDX("gpio", GPIO_GPIO21, NULL, 0,
This is what happened:
commit b2e63555592f81331c8da3afaa607d8cf83e8138
"i2c: gpio: Convert to use descriptors"
commit 4d0ce62c0a02e41a65cfdcfe277f5be430edc371
"i2c: gpio: Augment all boardfiles to use open drain"
together uncovered an old bug in the Simpad board
file: as theGPIO_LOOKUP_IDX() encodes GPIO offsets
on gpiochips in an u16 (see <linux/gpio/machine.h>)
these GPIO "numbers" does not fit, since in
arch/arm/mach-sa1100/include/mach/SA-1100.h it is
defined as:
#define GPIO_GPIO(Nb) (0x00000001 << (Nb))
(...)
#define GPIO_GPIO21 GPIO_GPIO(21) /* GPIO [21] */
This is however provably wrong, since the i2c-gpio
driver uses proper GPIO numbers, albeit earlier from
the global number space, whereas this GPIO_GPIO21
is the local line offset in the GPIO register, which
is used in other code but certainly not in the
gpiolib GPIO driver in drivers/gpio/gpio-sa1100.c, which
has code like this:
static void sa1100_gpio_set(struct gpio_chip *chip,
unsigned offset, int value)
{
int reg = value ? R_GPSR : R_GPCR;
writel_relaxed(BIT(offset),
sa1100_gpio_chip(chip)->membase + reg);
}
So far everything however compiled fine as an unsigned
int was used to pass the GPIO numbers in
struct i2c_gpio_platform_data. We can trace the actual error
back to
commit dbd406f9d0a1d33a1303eb75cbe3f9435513d339
"ARM: 7025/1: simpad: add GPIO based device definitions."
This added the i2c_gpio with the wrong offsets.
This commit was before the SA1100 was converted to use
the gpiolib, but as can be seen from the contemporary
gpio.c in mach-sa1100, it was already using:
static int sa1100_gpio_get(struct gpio_chip *chip,
unsigned offset)
{
return GPLR & GPIO_GPIO(offset);
}
And GPIO_GPIO() is essentially the BIT() macro.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
MFENCE appears to be way slower than a locked instruction - let's use
LOCK ADD unconditionally, as we always did on old 32-bit.
Performance testing results:
perf stat -r 10 -- ./virtio_ring_0_9 --sleep --host-affinity 0 --guest-affinity 0
Before:
0.922565990 seconds time elapsed ( +- 1.15% )
After:
0.578667024 seconds time elapsed ( +- 1.21% )
i.e. about ~60% faster.
Just poking at SP would be the most natural, but if we then read the
value from SP, we get a false dependency which will slow us down.
This was noted in this article:
http://shipilev.net/blog/2014/on-the-fence-with-dependencies/
And is easy to reproduce by sticking a barrier in a small non-inline
function.
So let's use a negative offset - which avoids this problem since we
build with the red zone disabled.
For userspace, use an address just below the redzone.
The one difference between LOCK ADD and MFENCE is that LOCK ADD does
not affect CLFLUSH, previous patches converted all uses of CLFLUSH to
call mb(), such that changes to smp_mb() won't affect it.
Update mb/rmb/wmb() on 32-bit to use the negative offset, too, for
consistency.
As a follow-up, it might be worth considering switching users
of CLFLUSH to another API (e.g. clflush_mb()?) - we will
then be able to convert mb() to smp_mb() again.
Also arguably, GCC should switch to use LOCK ADD for __sync_synchronize().
This might be worth pursuing separately.
Suggested-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: qemu-devel@nongnu.org
Cc: virtualization@lists.linux-foundation.org
Link: http://lkml.kernel.org/r/1509118355-4890-1-git-send-email-mst@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Check the JD status in the button pushing to prevent the IRQ that is locked
by button pushing event while the jack unpluging.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
remove unused tps_info structure.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currentlly tps_info structure is no longer used. So use the
strobes parameter in tps65218 structure to capture the info.
Fixes: 2dc4940360d4c0c (regulator: tps65218: Remove all the compatibles)
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When everything goes smoothly, ret is set to 0 which makes the function
to return EIO error.
Fixes: 8e9faa15469e ("HID: cp2112: fix gpio-callback error handling")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
On a non-preemptible kernel, if KEYCTL_DH_COMPUTE is called with the
largest permitted inputs (16384 bits), the kernel spends 10+ seconds
doing modular exponentiation in mpi_powm() without rescheduling. If all
threads do it, it locks up the system. Moreover, it can cause
rcu_sched-stall warnings.
Notwithstanding the insanity of doing this calculation in kernel mode
rather than in userspace, fix it by calling cond_resched() as each bit
from the exponent is processed. It's still noninterruptible, but at
least it's preemptible now.
Do the cond_resched() once per bit rather than once per MPI limb because
each limb might still easily take 100+ milliseconds on slow CPUs.
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
