| Age | Commit message (Collapse) | Author |
|---|
|
Commit d9fbc7f6431f "net: tcp: prefer listeners bound to an address"
removes port-only listener lookups. This caused segfaults in DCCP
lookups because DCCP did not initialize the (addr,port) hashtable.
This patch adds said initialization.
The only non-trivial issue here is the size of the new hashtable.
It seemed reasonable to make it match the size of the port-only
hashtable (= INET_LHTABLE_SIZE) that was used previously. Other
parameters to inet_hashinfo2_init() match those used in TCP.
Tested: syzcaller issues fixed; the second patch in the patchset
tests that DCCP lookups work correctly.
Fixes: d9fbc7f6431f "net: tcp: prefer listeners bound to an address"
Reported-by: syzcaller <syzkaller@googlegroups.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Peng Li says:
====================
net: hns: Code improvements & fixes for HNS driver
This patchset introduces some code improvements and fixes
for the identified problems in the HNS driver.
Every patch is independent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a net bridge, add eth and vnet to the bridge. The vnet is used
by a virtual machine. When ping the virtual machine from the outside
host and the virtual machine send multicast at the same time, the ping
package will lost.
The multicast package send to the eth, eth will send it to the bridge too,
and the bridge learn the mac of eth. When outside host ping the virtual
mechine, it will match the promisc entry of the eth which is not expected,
and the bridge send it to eth not to vnet, cause ping lost.
So this patch change promisc tcam entry position to the END of 512 tcam
entries, which indicate lower priority. And separate one promisc entry to
two: mc & uc, to avoid package match the wrong tcam entry.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some case, when mac enable|disable and adjust link, may cause hard to
link(or abnormal) between mac and phy. This patch adds the code for rx PCS
to avoid this bug.
Disable the rx PCS when driver disable the gmac, and enable the rx PCS
when driver enable the mac.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ntuple-filters features is forced on by chip.
But it shows "ntuple-filters: off [fixed]" when use ethtool.
This patch make it correct with "ntuple-filters: on [fixed]".
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There will be a large number of MAC pause frames on the net,
which caused tx timeout of net device. And then the net device
was reset to try to recover it. So that is not useful, and will
cause some other problems.
So need doubled ndev->watchdog_timeo if device watchdog occurred
until watchdog_timeo up to 40s and then try resetting to recover
it.
When collecting dfx information such as hardware registers when tx timeout.
Some registers for count were cleared when read. So need move this task
before update net state which also read the count registers.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1.In "hns_nic_init_irq", if request irq fail at index i,
the function return directly without releasing irq resources
that already requested.
2.In "hns_nic_net_up" after "hns_nic_init_irq",
if exceptional branch occurs, irqs that already requested
are not release.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If there are packets in hardware when changing the speed or duplex,
it may cause hardware hang up.
This patch adds the code to wait rx fbd clean up when ae stopped.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After resetting dsaf to try to repair chip error such as ecc error,
the net device will be open if net interface is up. But at this time
if there is the users set the net device up with the command ifconfig,
the net device will be opened twice consecutively.
Function napi_enable was called when open device. And Kernel panic will
be occurred if it was called twice consecutively. Such as follow:
static inline void napi_enable(struct napi_struct *n)
{
BUG_ON(!test_bit(NAPI_STATE_SCHED, &n->state));
smp_mb__before_clear_bit();
clear_bit(NAPI_STATE_SCHED, &n->state);
}
[37255.571996] Kernel panic - not syncing: BUG!
[37255.595234] Call trace:
[37255.597694] [<ffff80000008ab48>] dump_backtrace+0x0/0x1a0
[37255.603114] [<ffff80000008ad08>] show_stack+0x20/0x28
[37255.608187] [<ffff8000009c4944>] dump_stack+0x98/0xb8
[37255.613258] [<ffff8000009c149c>] panic+0x10c/0x26c
[37255.618070] [<ffff80000070f134>] hns_nic_net_up+0x30c/0x4e0
[37255.623664] [<ffff80000070f39c>] hns_nic_net_open+0x94/0x12c
[37255.629346] [<ffff80000084be78>] __dev_open+0xf4/0x168
[37255.634504] [<ffff80000084c1ac>] __dev_change_flags+0x98/0x15c
[37255.640359] [<ffff80000084c29c>] dev_change_flags+0x2c/0x68
[37255.769580] [<ffff8000008dc400>] devinet_ioctl+0x650/0x704
[37255.775086] [<ffff8000008ddc38>] inet_ioctl+0x98/0xb4
[37255.780159] [<ffff800000827b7c>] sock_do_ioctl+0x44/0x84
[37255.785490] [<ffff800000828e04>] sock_ioctl+0x248/0x30c
[37255.790737] [<ffff80000026dc6c>] do_vfs_ioctl+0x480/0x618
[37255.796156] [<ffff80000026de94>] SyS_ioctl+0x90/0xa4
[37255.801139] SMP: stopping secondary CPUs
[37255.805079] kbox: catch panic event.
[37255.809586] collected_len = 128928, LOG_BUF_LEN_LOCAL = 131072
[37255.816103] flush cache 0xffff80003f000000 size 0x800000
[37255.822192] flush cache 0xffff80003f000000 size 0x800000
[37255.828289] flush cache 0xffff80003f000000 size 0x800000
[37255.834378] kbox: no notify die func register. no need to notify
[37255.840413] ---[ end Kernel panic - not syncing: BUG!
This patchset fix this bug according to the flag NIC_STATE_DOWN.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the hip06 datasheet:
1.Six registers use wrong address:
RCB_COM_SF_CFG_INTMASK_RING
RCB_COM_SF_CFG_RING_STS
RCB_COM_SF_CFG_RING
RCB_COM_SF_CFG_INTMASK_BD
RCB_COM_SF_CFG_BD_RINT_STS
DSAF_INODE_VC1_IN_PKT_NUM_0_REG
2.The offset of DSAF_INODE_VC1_IN_PKT_NUM_0_REG should be
0x103C + 0x80 * all_chn_num
3.The offset to show the value of DSAF_INODE_IN_DATA_STP_DISC_0_REG
is wrong, so the value of DSAF_INODE_SW_VLAN_TAG_DISC_0_REG will be
overwrite
These registers are only used in "ethtool -d", so that did not cause ndev
to misfunction.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two test cases:
1. Remove the 4 modules:hns_enet_drv/hns_dsaf/hnae/hns_mdio,
and install them again, must use "ifconfig down/ifconfig up"
command pair to bring port to work.
This patch calls phy_stop function when init phy to fix this bug.
2. Remove the 2 modules:hns_enet_drv/hns_dsaf, and install them again,
all ports can not use anymore, because of the phy devices register
failed(phy devices already exists).
Phy devices are registered when hns_dsaf installed, this patch
removes them when hns_dsaf removed.
The two cases are sometimes related, fixing the second case also requires
fixing the first case, so fix them together.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the hip06 Datasheet:
1. The offset of INGRESS_SW_VLAN_TAG_DISC should be 0x1A00+4*all_chn_num
2. The offset of INGRESS_IN_DATA_STP_DISC should be 0x1A50+4*all_chn_num
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When Protocol Field Compression (PFC) is enabled, the "Protocol" field
in PPP packet will be received without leading 0x00. See section 6.5 in
RFC 1661 for details. So let's decompress protocol field if needed, the
same way it's done in drivers/net/ppp/pptp.c.
In case when "nopcomp" pppd option is not enabled, PFC (pcomp) can be
negotiated during LCP handshake, and L2TP driver in kernel will receive
PPP packets with compressed Protocol field, which in turn leads to next
error:
Protocol Rejected (unsupported protocol 0x2145)
because instead of Protocol=0x0021 in PPP packet there will be
Protocol=0x21. This patch unwraps it back to 0x0021, which fixes the
issue.
Sending the compressed Protocol field will be implemented in subsequent
patch, this one is self-sufficient.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-12-14 (VF Lag)
From Aviv Heller,
Subsequent patches introduce VF LAG, which provdies load-balancing and
high-availability capabilities for VFs associated with different
physical ports of the same Connect-X card.
This series consists of the following:
- mlx5 devcom, driver infrastructure that facilitates operations that involve
both core devices (physical functions) of the same card, to synchronize and
communicate between two driver instances of the same card.
- Infrastructure for TC rule duplication.
- Changes to LAG logic to enable its use when SR-IOV is enabled
- PFs in switchdev mode is the only mode currently supported.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sergey reported that forwarding was no longer working
if fq packet scheduler was used.
This is caused by the recent switch to EDT model, since incoming
packets might have been timestamped by __net_timestamp()
__net_timestamp() uses ktime_get_real(), while fq expects packets
using CLOCK_MONOTONIC base.
The fix is to clear skb->tstamp in forwarding paths.
Fixes: 80b14dee2bea ("net: Add a new socket option for a future transmit time.")
Fixes: fb420d5d91c1 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Sergey Matyukevich <geomatsi@gmail.com>
Tested-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Paolo Abeni says:
====================
net: mitigate retpoline overhead
The spectre v2 counter-measures, aka retpolines, are a source of measurable
overhead[1]. We can partially address that when the function pointer refers to
a builtin symbol resorting to a list of tests vs well-known builtin function and
direct calls.
Experimental results show that replacing a single indirect call via
retpoline with several branches and a direct call gives performance gains
even when multiple branches are added - 5 or more, as reported in [2].
This may lead to some uglification around the indirect calls. In netconf 2018
Eric Dumazet described a technique to hide the most relevant part of the needed
boilerplate with some macro help.
This series is a [re-]implementation of such idea, exposing the introduced
helpers in a new header file. They are later leveraged to avoid the indirect
call overhead in the GRO path, when possible.
Overall this gives > 10% performance improvement for UDP GRO benchmark and
smaller but measurable for TCP syn flood.
The added infra can be used in follow-up patches to cope with retpoline overhead
in other points of the networking stack (e.g. at the qdisc layer) and possibly
even in other subsystems.
v2 -> v3:
- fix build error with CONFIG_IPV6=m
v1 -> v2:
- list explicitly the builtin function names in INDIRECT_CALL_*(),
as suggested by Ed Cree
- expand the recipients list
rfc -> v1:
- use branch prediction hints, as suggested by Eric
[1] http://vger.kernel.org/netconf2018_files/PaoloAbeni_netconf2018.pdf
[2] https://linuxplumbersconf.org/event/2/contributions/99/attachments/98/117/lpc18_paper_af_xdp_perf-v2.pdf
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This avoids another indirect call for UDP GRO. Again, the test
for the IPv6 variant is performed first.
v1 -> v2:
- adapted to INDIRECT_CALL_ changes
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This avoids an indirect call in the receive path for TCP and UDP
packets. TCP takes precedence on UDP, so that we have a single
additional conditional in the common case.
When IPV6 is build as module, all gro symbols except UDPv6 are
builtin, while the latter belong to the ipv6 module, so we
need some special care.
v1 -> v2:
- adapted to INDIRECT_CALL_ changes
v2 -> v3:
- fix build issue with CONFIG_IPV6=m
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This avoids an indirect calls for L3 GRO receive path, both
for ipv4 and ipv6, if the latter is not compiled as a module.
Note that when IPv6 is compiled as builtin, it will be checked first,
so we have a single additional compare for the more common path.
v1 -> v2:
- adapted to INDIRECT_CALL_ changes
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This header define a bunch of helpers that allow avoiding the
retpoline overhead when calling builtin functions via function pointers.
It boils down to explicitly comparing the function pointers to
known builtin functions and eventually invoke directly the latter.
The macros defined here implement the boilerplate for the above schema
and will be used by the next patches.
rfc -> v1:
- use branch prediction hint, as suggested by Eric
v1 -> v2:
- list explicitly the builtin function names in INDIRECT_CALL_*(),
as suggested by Ed Cree
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the driver issues 2 mmio reads to figure out the number of
transmitted packets and clean them. We can get rid of the expensive
reads since BIT 31 of the Tx descriptor can be used for that.
We can also remove the budget counting of Tx completions since all of
the descriptors are not deliberately processed.
Performance numbers using pktgen are:
size pre-patch(pps) post-patch(pps)
64 362483 427916
128 358315 411686
256 352725 389683
512 215675 216464
1024 113812 114442
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Running pktgen with packets sizes > 512b ends up in the interface Txq
getting stuck.
"netsec 522d0000.ethernet eth0: netsec_netdev_start_xmit: TxQFull!"
appears on dmesg but the interface never recovers. It requires an
ifconfig down/up to make the interface usable again.
The reason that triggers this, is a race condition between
.ndo_start_xmit and the napi completion. The available budget is
calculated first and indicates the queue is full. Due to a costly
netif_err() the queue is not stopped in time while the napi completion
runs, clears the irq and frees up descriptors, thus the queue never wakes
up again.
Fix this by moving the print after stopping the queue, make the print
ratelimited, add barriers and check for cleaned descriptors..
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Document RZ/G2E (R8A774C0) SoC bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 7969e5c40dfd ("ip: discard IPv4 datagrams with overlapping
segments.") IPv4 reassembly code drops the whole queue whenever an
overlapping fragment is received. However, the test is written in a way
which detects duplicate fragments as overlapping so that in environments
with many duplicate packets, fragmented packets may be undeliverable.
Add an extra test and for (potentially) duplicate fragment, only drop the
new fragment rather than the whole queue. Only starting offset and length
are checked, not the contents of the fragments as that would be too
expensive. For similar reason, linear list ("run") of a rbtree node is not
iterated, we only check if the new fragment is a subset of the interval
covered by existing consecutive fragments.
v2: instead of an exact check iterating through linear list of an rbtree
node, only check if the new fragment is subset of the "run" (suggested
by Eric Dumazet)
Fixes: 7969e5c40dfd ("ip: discard IPv4 datagrams with overlapping segments.")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move arp_queue_len_bytes ahead of arp_queue to remove two 4-byte holes.
Ensure ha element is always 8-byte aligned.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added support for the Telit LN940 series cellular modules QMI interface.
QMI_QUIRK_SET_DTR quirk requied for Qualcomm MDM9x40 chipset.
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Except for returning, the var leaf is not
used in the qdisc_leaf(). For simplicity, remove it.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A recent commit allows sockets bound to a VRF to receive ipv6 link local
packets. However, it only works for UDP and worse TCP connection attempts
to the LLA with the only listener bound to the VRF just hang where as
before the client gets a reset and connection refused. Fix by adjusting
ir_iif for LL addresses and packets received through a device enslaved
to a VRF.
Fixes: 6f12fa775530 ("vrf: mark skb for multicast or link-local as enslaved to VRF")
Reported-by: Donald Sharp <sharpd@cumulusnetworks.com>
Cc: Mike Manning <mmanning@vyatta.att-mail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added support for Fibocom NL668 series QMI interface.
Using QMI_QUIRK_SET_DTR required for Qualcomm MDM9x07 chipsets.
Signed-off-by: Jörgen Storvist <jorgen.storvist@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Improve detection of spurious interrupts by checking against the
interrupt mask as currently set in the chip.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We already have the DEFINE_SHOW_ATTRIBUTE. There is no need to define
such a macro, so remove DEFINE_SIMPLE_DEBUGFS_FILE. Also use the
DEFINE_SHOW_ATTRIBUTE macro to simplify some code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf 2018-12-15
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) fix liveness propagation of callee saved registers, from Jakub.
2) fix overflow in bpf_jit_limit knob, from Daniel.
3) bpf_flow_dissector api fix, from Stanislav.
4) bpf_perf_event api fix on powerpc, from Sandipan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Salil Mehta says:
====================
net: hns3: Add more commands to Debugfs in HNS3 driver
This patch-set adds few more debugfs commands to HNS3 Ethernet
Driver. Support has been added to query info related to below
items:
1. Packet buffer descriptor ("echo bd info [queue no] [bd index] > cmd")
2. Manager table("echo dump mng tbl > cmd")
3. Dfx status register("echo dump reg ssu [prt id] > cmd")
4. Dcb status register("echo dump reg dcb [port id] > cmd")
5. Queue map ("echo queue map [queue no] > cmd")
6. Tm map ("echo tm map [queue no] > cmd")
NOTE: Above commands are *read-only* and are only intended to
query the information from the SoC(and dump inside the kernel,
for now) and in no way tries to perform write operations for
the purpose of configuration etc.
Change Log:
V1-->V2:
1. Addressed the GCC-8.2 compiler issue reported by David S. Miller.
Link: https://lkml.org/lkml/2018/12/14/1298
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch prints dcb register status information by module.
debugfs command:
root@(none)# echo dump tm map 100 > cmd
queue_id | qset_id | pri_id | tc_id
0100 | 0065 | 08 | 00
root@(none)#
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch prints queue map information.
debugfs command:
echo dump queue map > cmd
Sample Command:
root@(none)# echo queue map > cmd
local queue id | global queue id | vector id
0 32 769
1 33 770
2 34 771
3 35 772
4 36 773
5 37 774
6 38 775
7 39 776
8 40 777
9 41 778
10 42 779
11 43 780
12 44 781
13 45 782
14 46 783
15 47 784
root@(none)#
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch prints dcb register status information by module.
debugfs command:
root@(none)# echo dump reg dcb > cmd
roce_qset_mask: 0x0
nic_qs_mask: 0x0
qs_shaping_pass: 0x0
qs_bp_sts: 0x0
pri_mask: 0x0
pri_cshaping_pass: 0x0
pri_pshaping_pass: 0x0
root@(none)#
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch prints status register information by module.
debugfs command:
echo dump reg [mode name] > cmd
Sample Command:
root@(none)# echo dump reg bios common > cmd
BP_CPU_STATE: 0x0
DFX_MSIX_INFO_NIC_0: 0xc000
DFX_MSIX_INFO_NIC_1: 0xf
DFX_MSIX_INFO_NIC_2: 0x2
DFX_MSIX_INFO_NIC_3: 0x2
DFX_MSIX_INFO_ROC_0: 0xc000
DFX_MSIX_INFO_ROC_1: 0x0
DFX_MSIX_INFO_ROC_2: 0x0
DFX_MSIX_INFO_ROC_3: 0x0
root@(none)#
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch prints manager table information.
debugfs command:
echo dump mng tbl > cmd
Sample Command:
root@(none)# echo dump mng tbl > cmd
entry|mac_addr |mask|ether|mask|vlan|mask|i_map|i_dir|e_type
00 |01:00:5e:00:00:01|0 |00000|0 |0000|0 |00 |00 |0
01 |c2:f1:c5:82:68:17|0 |00000|0 |0000|0 |00 |00 |0
root@(none)#
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch prints Sending and receiving
package descriptor information.
debugfs command:
echo dump bd info 1 > cmd
Sample Command:
root@(none)# echo bd info 1 > cmd
hns3 0000:7d:00.0: TX Queue Num: 0, BD Index: 0
hns3 0000:7d:00.0: (TX) addr: 0x0
hns3 0000:7d:00.0: (TX)vlan_tag: 0
hns3 0000:7d:00.0: (TX)send_size: 0
hns3 0000:7d:00.0: (TX)vlan_tso: 0
hns3 0000:7d:00.0: (TX)l2_len: 0
hns3 0000:7d:00.0: (TX)l3_len: 0
hns3 0000:7d:00.0: (TX)l4_len: 0
hns3 0000:7d:00.0: (TX)vlan_tag: 0
hns3 0000:7d:00.0: (TX)tv: 0
hns3 0000:7d:00.0: (TX)vlan_msec: 0
hns3 0000:7d:00.0: (TX)ol2_len: 0
hns3 0000:7d:00.0: (TX)ol3_len: 0
hns3 0000:7d:00.0: (TX)ol4_len: 0
hns3 0000:7d:00.0: (TX)paylen: 0
hns3 0000:7d:00.0: (TX)vld_ra_ri: 0
hns3 0000:7d:00.0: (TX)mss: 0
hns3 0000:7d:00.0: RX Queue Num: 0, BD Index: 120
hns3 0000:7d:00.0: (RX)addr: 0xffee7000
hns3 0000:7d:00.0: (RX)pkt_len: 0
hns3 0000:7d:00.0: (RX)size: 0
hns3 0000:7d:00.0: (RX)rss_hash: 0
hns3 0000:7d:00.0: (RX)fd_id: 0
hns3 0000:7d:00.0: (RX)vlan_tag: 0
hns3 0000:7d:00.0: (RX)o_dm_vlan_id_fb: 0
hns3 0000:7d:00.0: (RX)ot_vlan_tag: 0
hns3 0000:7d:00.0: (RX)bd_base_info: 0
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Quentin Monnet says:
====================
This series contains several minor fixes for bpftool source and
documentation.
The first patches focus on documentation: addition of an option in the page
for "bpftool prog", clean up and update of the same page, and addition of
an example of prog array map manipulation in "bpftool map" page.
The last two fix warnings susceptible to appear when libbfd is not present
(patch 4), or with additional warning flags passed to the compiler (last
patch).
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Help compiler check arguments for several utility functions used to
print items to the console by adding the "printf" attribute when
declaring those functions.
Also, declare as "static" two functions that are only used in prog.c.
All of them discovered by compiling bpftool with
-Wmissing-format-attribute -Wmissing-declarations.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The following warning appears when compiling bpftool without BFD
support:
main.h:198:23: warning: 'struct bpf_prog_linfo' declared inside
parameter list will not be visible outside of this definition or
declaration
const struct bpf_prog_linfo *prog_linfo,
Fix it by declaring struct bpf_prog_linfo even in the case BFD is not
supported.
Fixes: b053b439b72a ("bpf: libbpf: bpftool: Print bpf_line_info during prog dump")
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Add an example in map documentation to show how to use bpftool in order
to update the references to programs hold by prog array maps.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Bring various fixes to the manual page for "bpftool prog" set of
commands:
- Fix typos ("dum" -> "dump")
- Harmonise indentation and format for command output
- Update date format for program load time
- Add instruction numbers on program dumps
- Fix JSON format for the example program listing
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The --mapcompat|-m option has been documented on the main bpftool.rst
page, and on the interactive help. As this option is useful for loading
programs with maps with the "bpftool prog load" command, it should also
appear in the related bpftool-prog.rst documentation page. Let's add it.
Signed-off-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Alexei Starovoitov says:
====================
v1->v2:
With optimization suggested by Jakub patch 4 safety check became
cheap enough.
Several improvements to verifier state logic.
Patch 1 - trivial optimization
Patch 3 - significant optimization for stack state equivalence
Patch 4 - safety check for liveness and prep for future state merging
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Introduce REG_LIVE_DONE to check the liveness propagation
and prepare the states for merging.
See algorithm description in clean_live_states().
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
"if (old->allocated_stack > cur->allocated_stack)" check is too conservative.
In some cases explored stack could have allocated more space,
but that stack space was not live.
The test case improves from 19 to 15 processed insns
and improvement on real programs is significant as well:
before after
bpf_lb-DLB_L3.o 1940 1831
bpf_lb-DLB_L4.o 3089 3029
bpf_lb-DUNKNOWN.o 1065 1064
bpf_lxc-DDROP_ALL.o 28052 26309
bpf_lxc-DUNKNOWN.o 35487 33517
bpf_netdev.o 10864 9713
bpf_overlay.o 6643 6184
bpf_lcx_jit.o 38437 37335
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Edward Cree <ecree@solarflare.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
