| Age | Commit message (Collapse) | Author |
|---|
|
The LED implementation of qca808x and qca807x is the same but qca807x
supports also Fiber port and have different hw control bits for Fiber
port.
In preparation for qca807x introduction, move all the common define to
shared header.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds driver for the Qualcomm QCA8072 and QCA8075 PHY-s.
They are 2 or 5 port IEEE 802.3 clause 22 compliant 10BASE-Te,
100BASE-TX and 1000BASE-T PHY-s.
They feature 2 SerDes, one for PSGMII or QSGMII connection with
MAC, while second one is SGMII for connection to MAC or fiber.
Both models have a combo port that supports 1000BASE-X and
100BASE-FX fiber.
PHY package can be configured in 3 mode following this table:
First Serdes mode Second Serdes mode
Option 1 PSGMII for copper Disabled
ports 0-4
Option 2 PSGMII for copper 1000BASE-X / 100BASE-FX
ports 0-4
Option 3 QSGMII for copper SGMII for
ports 0-3 copper port 4
Each PHY inside of QCA807x series has 4 digitally controlled
output only pins that natively drive LED-s.
But some vendors used these to driver generic LED-s controlled
by userspace, so lets enable registering each PHY as GPIO
controller and add driver for it.
These are commonly used in Qualcomm IPQ40xx, IPQ60xx and IPQ807x
boards.
Co-developed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some PHY driver might require additional regs call after
genphy_c37_read_status() is called.
Expand genphy_c37_read_status to provide a bool wheather the link has
changed or not to permit PHY driver to skip additional regs call if
nothing has changed.
Every user of genphy_c37_read_status() is updated with the new
additional bool.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Document Qcom QCA807x PHY package.
Qualcomm QCA807X Ethernet PHY is PHY package of 2 or 5
IEEE 802.3 clause 22 compliant 10BASE-Te, 100BASE-TX and
1000BASE-T PHY-s.
Document the required property to make the PHY package correctly
configure and work.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move more function to shared library in preparation for introduction of
new PHY Family qca807x that will make use of both functions from at803x
and qca808x as it's a transition PHY with some implementation of at803x
and some from the new qca808x.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devm/of_phy_package_join helper to join PHYs in a PHY package. These
are variant of the manual phy_package_join with the difference that
these will use DT nodes to derive the base_addr instead of manually
passing an hardcoded value.
An additional value is added in phy_package_shared, "np" to reference
the PHY package node pointer in specific PHY driver probe_once and
config_init_once functions to make use of additional specific properties
defined in the PHY package node in DT.
The np value is filled only with of_phy_package_join if a valid PHY
package node is found. A valid PHY package node must have the node name
set to "ethernet-phy-package".
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for scanning PHY in PHY package nodes. PHY packages nodes
are just container for actual PHY on the MDIO bus.
Their PHY address defined in the PHY package node are absolute and
reflect the address on the MDIO bus.
mdio_bus.c and of_mdio.c is updated to now support and parse also
PHY package subnode by checking if the node name match
"ethernet-phy-package".
As PHY package reg is mandatory and each PHY in the PHY package must
have a reg, every invalid PHY Package node is ignored and will be
skipped by the autoscan fallback.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Document ethernet PHY package nodes used to describe PHY shipped in
bundle of 2-5 PHY. The special node describe a container of PHY that
share common properties. This is a generic schema and PHY package
should create specialized version with the required additional shared
properties.
Example are PHY packages that have some regs only in one PHY of the
package and will affect every other PHY in the package, for example
related to PHY interface mode calibration or global PHY mode selection.
The PHY package node MUST declare the base address used by the PHY driver
for global configuration by calculating the offsets of the global PHY
based on the base address of the PHY package.
Each reg of the PHYs defined in the PHY package node is absolute and
describe the real address of the Ethernet PHY on the bus.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 57851607326a2beef21e67f83f4f53a90df8445a.
Unfortunately, while we only call that thing once, the callback
*can* be called more than once for the same dentry - all it
takes is rename_lock being touched while we are in d_walk().
For now let's revert it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three small driver fixes and one core fix.
The core fix being a fixup to the one in the last pull request which
didn't entirely move checking of scsi_host_busy() out from under the
host lock"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Remove the ufshcd_release() in ufshcd_err_handling_prepare()
scsi: ufs: core: Fix shift issue in ufshcd_clear_cmd()
scsi: lpfc: Use unsigned type for num_sge
scsi: core: Move scsi_host_busy() out of host lock if it is for per-command
|
|
Pull smb client fixes from Steve French:
- reconnect fix
- multichannel channel selection fix
- minor mount warning fix
- reparse point fix
- null pointer check improvement
* tag '6.8-rc3-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb3: clarify mount warning
cifs: handle cases where multiple sessions share connection
cifs: change tcon status when need_reconnect is set on it
smb: client: set correct d_type for reparse points under DFS mounts
smb3: add missing null server pointer check
|
|
Pull ceph fixes from Ilya Dryomov:
"Some fscrypt-related fixups (sparse reads are used only for encrypted
files) and two cap handling fixes from Xiubo and Rishabh"
* tag 'ceph-for-6.8-rc4' of https://github.com/ceph/ceph-client:
ceph: always check dir caps asynchronously
ceph: prevent use-after-free in encode_cap_msg()
ceph: always set initial i_blkbits to CEPH_FSCRYPT_BLOCK_SHIFT
libceph: just wait for more data to be available on the socket
libceph: rename read_sparse_msg_*() to read_partial_sparse_msg_*()
libceph: fail sparse-read if the data length doesn't match
|
|
https://github.com/Paragon-Software-Group/linux-ntfs3
Pull ntfs3 fixes from Konstantin Komarov:
"Fixed:
- size update for compressed file
- some logic errors, overflows
- memory leak
- some code was refactored
Added:
- implement super_operations::shutdown
Improved:
- alternative boot processing
- reduced stack usage"
* tag 'ntfs3_for_6.8' of https://github.com/Paragon-Software-Group/linux-ntfs3: (28 commits)
fs/ntfs3: Slightly simplify ntfs_inode_printk()
fs/ntfs3: Add ioctl operation for directories (FITRIM)
fs/ntfs3: Fix oob in ntfs_listxattr
fs/ntfs3: Fix an NULL dereference bug
fs/ntfs3: Update inode->i_size after success write into compressed file
fs/ntfs3: Fixed overflow check in mi_enum_attr()
fs/ntfs3: Correct function is_rst_area_valid
fs/ntfs3: Use i_size_read and i_size_write
fs/ntfs3: Prevent generic message "attempt to access beyond end of device"
fs/ntfs3: use non-movable memory for ntfs3 MFT buffer cache
fs/ntfs3: Use kvfree to free memory allocated by kvmalloc
fs/ntfs3: Disable ATTR_LIST_ENTRY size check
fs/ntfs3: Fix c/mtime typo
fs/ntfs3: Add NULL ptr dereference checking at the end of attr_allocate_frame()
fs/ntfs3: Add and fix comments
fs/ntfs3: ntfs3_forced_shutdown use int instead of bool
fs/ntfs3: Implement super_operations::shutdown
fs/ntfs3: Drop suid and sgid bits as a part of fpunch
fs/ntfs3: Add file_modified
fs/ntfs3: Correct use bh_read
...
|
|
We've had issues with gcc and 'asm goto' before, and we created a
'asm_volatile_goto()' macro for that in the past: see commits
3f0116c3238a ("compiler/gcc4: Add quirk for 'asm goto' miscompilation
bug") and a9f180345f53 ("compiler/gcc4: Make quirk for
asm_volatile_goto() unconditional").
Then, much later, we ended up removing the workaround in commit
43c249ea0b1e ("compiler-gcc.h: remove ancient workaround for gcc PR
58670") because we no longer supported building the kernel with the
affected gcc versions, but we left the macro uses around.
Now, Sean Christopherson reports a new version of a very similar
problem, which is fixed by re-applying that ancient workaround. But the
problem in question is limited to only the 'asm goto with outputs'
cases, so instead of re-introducing the old workaround as-is, let's
rename and limit the workaround to just that much less common case.
It looks like there are at least two separate issues that all hit in
this area:
(a) some versions of gcc don't mark the asm goto as 'volatile' when it
has outputs:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=98619
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=110420
which is easy to work around by just adding the 'volatile' by hand.
(b) Internal compiler errors:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=110422
which are worked around by adding the extra empty 'asm' as a
barrier, as in the original workaround.
but the problem Sean sees may be a third thing since it involves bad
code generation (not an ICE) even with the manually added 'volatile'.
but the same old workaround works for this case, even if this feels a
bit like voodoo programming and may only be hiding the issue.
Reported-and-tested-by: Sean Christopherson <seanjc@google.com>
Link: https://lore.kernel.org/all/20240208220604.140859-1-seanjc@google.com/
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Uros Bizjak <ubizjak@gmail.com>
Cc: Jakub Jelinek <jakub@redhat.com>
Cc: Andrew Pinski <quic_apinski@quicinc.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Breno Leitao says:
====================
net: Fix MODULE_DESCRIPTION() for net (p5)
There are hundreds of network modules that misses MODULE_DESCRIPTION(),
causing a warning when compiling with W=1. Example:
WARNING: modpost: missing MODULE_DESCRIPTION() in net/sched/em_cmp.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/sched/em_nbyte.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/sched/em_u32.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/sched/em_meta.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/sched/em_text.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/sched/em_canid.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/ipv4/ip_tunnel.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/ipv4/ipip.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/ipv4/ip_gre.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/ipv4/udp_tunnel.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/ipv4/ip_vti.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/ipv4/ah4.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/ipv4/esp4.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/ipv4/xfrm4_tunnel.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/ipv4/tunnel4.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/xfrm/xfrm_algo.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/xfrm/xfrm_user.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/ipv6/ah6.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/ipv6/esp6.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/ipv6/xfrm6_tunnel.o
WARNING: modpost: missing MODULE_DESCRIPTION() in net/ipv6/tunnel6.o
This part5 of the patchset focus on the missing net/ module, which
are now warning free.
v1: https://lore.kernel.org/all/20240205101400.1480521-1-leitao@debian.org/
v2: https://lore.kernel.org/all/20240207101929.484681-1-leitao@debian.org/
====================
Link: https://lore.kernel.org/r/20240208164244.3818498-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the DSA loopback fixed PHY module.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20240208164244.3818498-10-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the IP-VLAN based tap driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240208164244.3818498-9-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the network schedulers.
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20240208164244.3818498-8-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the IPv4 modules.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240208164244.3818498-7-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the IPv6 modules.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240208164244.3818498-6-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to IPv6 over Low power Wireless Personal Area Network.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Alexander Aring <aahringo@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240208164244.3818498-5-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the PF_KEY socket helpers.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240208164244.3818498-4-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the Multi-Protocol Over ATM (MPOA) driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240208164244.3818498-3-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
W=1 builds now warn if module is built without a MODULE_DESCRIPTION().
Add descriptions to the XFRM interface drivers.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240208164244.3818498-2-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use generic MDIO helpers to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/422ae70f-7305-45fd-ab3e-0dd604b9fd6c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a crash when adding one of the lan966x interfaces under a lag
interface. The issue can be reproduced like this:
ip link add name bond0 type bond miimon 100 mode balance-xor
ip link set dev eth0 master bond0
The reason is because when adding a interface under the lag it would go
through all the ports and try to figure out which other ports are under
that lag interface. And the issue is that lan966x can have ports that are
NULL pointer as they are not probed. So then iterating over these ports
it would just crash as they are NULL pointers.
The fix consists in actually checking for NULL pointers before accessing
something from the ports. Like we do in other places.
Fixes: cabc9d49333d ("net: lan966x: Add lag support for lan966x")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240206123054.3052966-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
igc: ethtool: Flex filter cleanup
Kurt Kanzenbach says:
This series contains some cosmetics for the flex filter code. The fixes have
been merged separately via -net already.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igc: Unify filtering rule fields
igc: Use netdev printing functions for flex filters
igc: Use reverse xmas tree
====================
Link: https://lore.kernel.org/r/20240207191656.1250777-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
While testing tdc with parallel tests for mirred to block we caught an
intermittent bug. The blockid was being zeroed out when a net device
was deleted and, thus, giving us an incorrect blockid value whenever
we tried to dump the mirred action. Since we don't increment the block
refcount in the control path (and only use the ID), we don't need to
zero the blockid field whenever a net device is going down.
Fixes: 42f39036cda8 ("net/sched: act_mirred: Allow mirred to block")
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20240207222902.1469398-1-victor@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
udpgso regression test configures routing and device MTU directly through
uAPI (Netlink, ioctl) to do its job. While there is nothing wrong with it,
it takes more effort than doing it from shell.
Looking forward, we would like to extend the udpgso regression tests to
cover the EIO corner case [1], once it gets addressed. That will require a
dummy device and device feature manipulation to set it up. Which means more
Netlink code.
So, in preparation, pull out network configuration into the shell script
part of the test, so it is easily extendable in the future.
Also, because it now easy to setup routing, add a second local IPv6
address. Because the second address is not managed by the kernel, we can
"replace" the corresponding local route with a reduced-MTU one. This
unblocks the disabled "ipv6 connected" test case. Add a similar setup for
IPv4 for symmetry.
[1] https://lore.kernel.org/netdev/87jzqsld6q.fsf@cloudflare.com/
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://lore.kernel.org/r/20240207-jakub-krn-635-v3-1-3dfa3da8a7d3@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert EEE handling to use linkmode bitmaps. This prepares for
removing the legacy bitmaps from struct ethtool_keee.
No functional change intended.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/c5a61d57-d2b0-427f-93b3-fcf7721165f3@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert EEE handling to use linkmode bitmaps. This prepares for
removing the legacy bitmaps from struct ethtool_keee.
No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/948562fb-c5d8-4912-8b88-bec56238732a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Aaron Conole says:
====================
net: openvswitch: limit the recursions from action sets
Open vSwitch module accepts actions as a list from the netlink socket
and then creates a copy which it uses in the action set processing.
During processing of the action list on a packet, the module keeps a
count of the execution depth and exits processing if the action depth
goes too high.
However, during netlink processing the recursion depth isn't checked
anywhere, and the copy trusts that kernel has large enough stack to
accommodate it. The OVS sample action was the original action which
could perform this kinds of recursion, and it originally checked that
it didn't exceed the sample depth limit. However, when sample became
optimized to provide the clone() semantics, the recursion limit was
dropped.
This series adds a depth limit during the __ovs_nla_copy_actions() call
that will ensure we don't exceed the max that the OVS userspace could
generate for a clone().
Additionally, this series provides a selftest in 2/2 that can be used to
determine if the OVS module is allowing unbounded access. It can be
safely omitted where the ovs selftest framework isn't available.
====================
Link: https://lore.kernel.org/r/20240207132416.1488485-1-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a test case into the netlink checks that will show the number of
nested action recursions won't exceed 16. Going to 17 on a small
clone call isn't enough to exhaust the stack on (most) systems, so
it should be safe to run even on systems that don't have the fix
applied.
Signed-off-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240207132416.1488485-3-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ovs module allows for some actions to recursively contain an action
list for complex scenarios, such as sampling, checking lengths, etc.
When these actions are copied into the internal flow table, they are
evaluated to validate that such actions make sense, and these calls
happen recursively.
The ovs-vswitchd userspace won't emit more than 16 recursion levels
deep. However, the module has no such limit and will happily accept
limits larger than 16 levels nested. Prevent this by tracking the
number of recursions happening and manually limiting it to 16 levels
nested.
The initial implementation of the sample action would track this depth
and prevent more than 3 levels of recursion, but this was removed to
support the clone use case, rather than limited at the current userspace
limit.
Fixes: 798c166173ff ("openvswitch: Optimize sample action for the clone use cases")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240207132416.1488485-2-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After 3a2746320403 ("leds: trigger: netdev: Display only supported link
speed attribute") the check for valid link modes can be simplified.
In addition factor it out, so that it can be re-used by the upcoming
LED support for RTL8125.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/8876a9f4-7a2d-48c3-8eae-0d834f5c27c5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The altnames test uses the forwarding/lib.sh and that dependency
currently causes failures when running the test after install:
make -C tools/testing/selftests/ TARGETS=net install
./tools/testing/selftests/kselftest_install/run_kselftest.sh \
-t net:altnames.sh
# ...
# ./altnames.sh: line 8: ./forwarding/lib.sh: No such file or directory
# RTNETLINK answers: Operation not permitted
# ./altnames.sh: line 73: tests_run: command not found
# ./altnames.sh: line 65: pre_cleanup: command not found
Address the issue leveraging the TEST_INCLUDES infrastructure
provided by commit 2a0683be5b4c ("selftests: Introduce Makefile variable
to list shared bash scripts")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/f7b1e9d468224cbc136d304362315499fe39848f.1707298927.git.pabeni@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a user tries to use the "sec=krb5p" mount parameter to encrypt
data on connection to a server (when authenticating with Kerberos), we
indicate that it is not supported, but do not note the equivalent
recommended mount parameter ("sec=krb5,seal") which turns on encryption
for that mount (and uses Kerberos for auth). Update the warning message.
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Based on our implementation of multichannel, it is entirely
possible that a server struct may not be found in any channel
of an SMB session.
In such cases, we should be prepared to move on and search for
the server struct in the next session.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
When a tcon is marked for need_reconnect, the intention
is to have it reconnected.
This change adjusts tcon->status in cifs_tree_connect
when need_reconnect is set. Also, this change has a minor
correction in resetting need_reconnect on success. It makes
sure that it is done with tc_lock held.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Michael Chan says:
====================
bnxt_en: Ntuple and RSS updates
This patch series adds more ntuple and RSS features following recent
patches to add support for user configured ntuple filters. Additional
features include L2 ether filters, partial tuple masks, IP filters
besides TCP/UDP, drop action, saving and re-applying user filters
after driver reset, user configured RSS key, and RSS for IPSEC.
====================
Link: https://lore.kernel.org/r/20240205223202.25341-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IPSec uses two distinct protocols, Authentication Header (AH) and
Encapsulating Security Payload (ESP).
Add support to configure RSS based on AH and ESP headers.
This functionality will be enabled based on the capabilities
indicated by the firmware in HWRM_VNIC_QCAPS.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240205223202.25341-14-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The cached user filters slated to be reapplied need to
be cleared if configured MAC changes, RSS key changes,
number of rings changes, or ntuple is disabled.
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240205223202.25341-13-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Store the user configured or generated Toeplitz key in
bp->rss_hash_key. The key stays constant across ifdown/ifup
unless updated by the user.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240205223202.25341-12-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Walk the usr_fltr_list and call firmware to add these filters when
we open the NIC. This will restore all user created filters after
reset.
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240205223202.25341-11-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Driver should not free user created filters from its memory
when closing since we are going to reconfigure them when
we open again. If the "all" parameter is false, do not free
user configured filters in bnxt_free_ntp_fltrs() and
bnxt_free_l2_filters().
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240205223202.25341-10-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Driver needs to maintain a lookup list of all the user configured
filters. This is required in order to reconfigure these filters upon
interface toggle. We can look up this list to follow the order with
which they should be re-applied.
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240205223202.25341-9-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since we are going to do filter deletion at multiple places in the
upcoming patches, add a function that does the deletion. Future patches
add more code into this function.
Since we are passing the address of the filter base to free the
entire filter structure, add a comment to make sure that the base
is always at the beginning of the structure.
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240205223202.25341-8-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add drop action for protocols TCP/UDP/ICMP
1) Drop action for TCP/UDP is supported via flow type
tcp4/udp4/tcp6/udp6.
2) Drop action for ICMPV4/ICMPV6/wildcard is supported
via flow type ipv4/ipv6.
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240205223202.25341-7-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Enable flow type ipv4/ipv6
1) for protocols ICMPV4 and ICMPV6.
2) for wildcard match. Wildcard matches to TCP/UDP/ICMP.
Note that, IPPROTO_RAW(255) i.e. a reserved protocol
considered for a wildcard.
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240205223202.25341-6-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Support subfield masking for IP addresses and ports. Previously, only
entire fields could be included or excluded in NTUPLE filters.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://lore.kernel.org/r/20240205223202.25341-5-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
