| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for-v4.4-rc5
Hopefully final set of fixes for v4.4 release cycle.
There's a fix for a regression on dwc3 caused by recent changes to how
transfers are started. We're not pre-starting interrupt endpoints
anymore.
A NULL pointer dereference fix for the MSM phy driver.
The UVC gadget got a minor fix for permissions to its configfs
attributes and, finally, two fixes for MUSB. A fix for PM runtime when
MUSB returns EPROBE_DEFER and a fix to actually return an error in case
we can't initialize a DMA engine.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes, both -stable fodder (9p one all way back to 2.6.32,
dio - to all branches where "Fix negative return from dio read beyond
eof" will end up it; it's a fixup to commit marked for -stable)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix the regression from "direct-io: Fix negative return from dio read beyond eof"
9p: ->evict_inode() should kick out ->i_data, not ->i_mapping
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are more fixes I'd like to have in v4.4. Several for the Altera
driver added for v4.4, and one for an MSI domain problem that affects
several arm64 platforms:
MSI:
- Only use the generic MSI layer when domain is hierarchical (Marc
Zyngier)
Altera host bridge driver:
- Fix loop in tlp_read_packet() (Dan Carpenter)
- Fix Requester ID for config accesses (Ley Foon Tan)
- Check TLP completion status (Ley Foon Tan)
- Fix error when INTx is 4 (Ley Foon Tan)"
* tag 'pci-v4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: altera: Fix error when INTx is 4
PCI: altera: Check TLP completion status
PCI: altera: Fix Requester ID for config accesses
PCI: altera: Fix loop in tlp_read_packet()
PCI/MSI: Only use the generic MSI layer when domain is hierarchical
|
|
This refactors the EFI init and runtime code that will be shared
between arm64 and ARM so that it can be built for both archs.
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This splits off the early EFI init and runtime code that
- discovers the EFI params and the memory map from the FDT, and installs
the memblocks and config tables.
- prepares and installs the EFI page tables so that UEFI Runtime Services
can be invoked at the virtual address installed by the stub.
This will allow it to be reused for 32-bit ARM.
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Change the EFI memory reservation logic to use memblock_mark_nomap()
rather than memblock_reserve() to mark UEFI reserved regions as
occupied. In addition to reserving them against allocations done by
memblock, this will also prevent them from being covered by the linear
mapping.
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Take the new memblock attribute MEMBLOCK_NOMAP into account when
deciding whether a certain region is or should be covered by the
kernel direct mapping.
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
This introduces the MEMBLOCK_NOMAP attribute and the required plumbing
to make it usable as an indicator that some parts of normal memory
should not be covered by the kernel direct mapping. It is up to the
arch to actually honor the attribute when laying out this mapping,
but the memblock code itself is modified to disregard these regions
for allocations and other general use.
Cc: linux-mm@kvack.org
Cc: Alexander Kuleshov <kuleshovmail@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Move cmd_version() to its own file so that help.c can be moved to a
library.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/e908b1b68f20ab6d8d33941d5571c23110622e60.1449548395.git.jpoimboe@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
perf_env__set_cmdline() only saves the arguments the first time it's
called. It doesn't need to be called every time the options and
suboptions are parsed. Instead it can just be called once.
This also has the advantage of making the option parsing code less
perf-specific so it can be moved out to a library.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/19b76a5aa1b688bd635bd65d80bbc103a978d75e.1449548395.git.jpoimboe@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The term functions are needed by help.c which is going to be moved into
a separate library. Move them out of util.c and into their own file.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/9a39c854dd156b55ebda57e427594c9a59dcb40f.1449548395.git.jpoimboe@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/e540c61b3068761181db6d9b1b3411990bafdb2f.1449548395.git.jpoimboe@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Fix write_numa_topology to put cpu_map instead of free because cpu_map
is managed based on refcnt.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20151209021135.10245.79046.stgit@localhost.localdomain
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Fix machine.vmlinux_maps to make sure to clear the old one if it is
renewal. This can leak the previous maps on the vmlinux_maps because
those are just overwritten.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20151209021133.10245.93730.stgit@localhost.localdomain
[ Simplified the memset, same end result ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Since the __map_groups__insert got the given map, we don't need to keep
it. So put the maps.
Refcnt debugger shows that map_groups__fixup_overlappings() got a map
twice but the group released it just once. This pattern usually
indicates the leak happens in caller site.
----
==== [0] ====
Unreclaimed map@0x39d3ae0
Refcount +1 => 1 at
./perf(map_groups__fixup_overlappings+0x335) [0x4c1865]
./perf(thread__insert_map+0x30) [0x4c8e00]
./perf(machine__process_mmap2_event+0x106) [0x4bd876]
./perf() [0x4c378e]
./perf() [0x4c4393]
./perf(perf_session__process_events+0x38a) [0x4c654a]
./perf(cmd_record+0xe24) [0x42fc94]
./perf() [0x47b745]
./perf(main+0x617) [0x422547]
/lib64/libc.so.6(__libc_start_main+0xf5) [0x7f2eca2deaf5]
./perf() [0x4226bd]
Refcount +1 => 2 at
./perf(map_groups__fixup_overlappings+0x3c5) [0x4c18f5]
./perf(thread__insert_map+0x30) [0x4c8e00]
./perf(machine__process_mmap2_event+0x106) [0x4bd876]
./perf() [0x4c378e]
./perf() [0x4c4393]
./perf(perf_session__process_events+0x38a) [0x4c654a]
./perf(cmd_record+0xe24) [0x42fc94]
./perf() [0x47b745]
./perf(main+0x617) [0x422547]
/lib64/libc.so.6(__libc_start_main+0xf5) [0x7f2eca2deaf5]
./perf() [0x4226bd]
Refcount -1 => 1 at
./perf(map_groups__exit+0x92) [0x4c0962]
./perf(map_groups__put+0x60) [0x4c0bc0]
./perf(thread__put+0x90) [0x4c8a40]
./perf(machine__delete_threads+0x7e) [0x4bad9e]
./perf(perf_session__delete+0x4f) [0x4c499f]
./perf(cmd_record+0xb6d) [0x42f9dd]
./perf() [0x47b745]
./perf(main+0x617) [0x422547]
/lib64/libc.so.6(__libc_start_main+0xf5) [0x7f2eca2deaf5]
./perf() [0x4226bd]
----
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20151209021131.10245.41485.stgit@localhost.localdomain
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Since hists__init doesn't set the destructor of hists_evsel (which is an
extended evsel structure), when hists_evsel is released, the extended
part of the hists_evsel is not deleted (note that the hists_evsel object
itself is freed).
This fixes it to add a destructor for hists__evsel and to set it up.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20151209021129.10245.28710.stgit@localhost.localdomain
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Fix cmd_stat() to release cpu_map objects (aggr_map and
cpus_aggr_map) afterwards.
refcnt debugger shows that the cmd_stat initializes cpu_map
but not puts it.
----
# ./perf stat -v ls
....
REFCNT: BUG: Unreclaimed objects found.
==== [0] ====
Unreclaimed cpu_map@0x29339c0
Refcount +1 => 1 at
./perf(cpu_map__empty_new+0x6d) [0x4e64bd]
./perf(cmd_stat+0x5fe) [0x43594e]
./perf() [0x47b785]
./perf(main+0x617) [0x422587]
/lib64/libc.so.6(__libc_start_main+0xf5) [0x7f2dff420af5]
./perf() [0x4226fd]
REFCNT: Total 1 objects are not reclaimed.
"cpu_map" leaks 1 objects
----
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20151209021127.10245.93697.stgit@localhost.localdomain
[ Remove NULL checks before calling the put operation, it checks it already ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Fix map_groups__clone to put cloned map after inserting it to the
map_groups.
Refcnt debugger shows:
----
==== [0] ====
Unreclaimed map: 0x2a27ee0
Refcount +1 => 1 at
./perf(map_groups__clone+0x8d) [0x4bb7ed]
./perf(thread__fork+0xbe) [0x4c1f9e]
./perf(machine__process_fork_event+0x216) [0x4b79a6]
./perf(perf_event__synthesize_threads+0x38b) [0x48135b]
./perf(cmd_top+0xdc6) [0x43cb76]
./perf() [0x477223]
./perf(main+0x617) [0x422077]
/lib64/libc.so.6(__libc_start_main+0xf0) [0x7ff806af8fe0]
./perf() [0x4221ed]
Refcount +1 => 2 at
./perf(map_groups__clone+0x128) [0x4bb888]
./perf(thread__fork+0xbe) [0x4c1f9e]
./perf(machine__process_fork_event+0x216) [0x4b79a6]
./perf(perf_event__synthesize_threads+0x38b) [0x48135b]
./perf(cmd_top+0xdc6) [0x43cb76]
./perf() [0x477223]
./perf(main+0x617) [0x422077]
/lib64/libc.so.6(__libc_start_main+0xf0) [0x7ff806af8fe0]
./perf() [0x4221ed]
Refcount -1 => 1 at
./perf(map_groups__exit+0x87) [0x4ba757]
./perf(map_groups__put+0x68) [0x4ba9a8]
./perf(thread__put+0x8b) [0x4c1aeb]
./perf(machine__delete_threads+0x81) [0x4b48f1]
./perf(perf_session__delete+0x4f) [0x4be63f]
./perf(cmd_top+0x1094) [0x43ce44]
./perf() [0x477223]
./perf(main+0x617) [0x422077]
/lib64/libc.so.6(__libc_start_main+0xf0) [0x7ff806af8fe0]
./perf() [0x4221ed]
----
This shows map_groups__clone get the map twice and put it when
map_groups__exit.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20151209021120.10245.95388.stgit@localhost.localdomain
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Boris reported that 'perf top' is unusable on his default 'black on
white' terminal, which uses (eye friendly) light-grey as a background
color.
The reason is that the TUI cursor for the current selection line uses
HE_COLORSET_SELECTED, and that has a default background color of
'lightgrey' - which is a common terminal background choice and thus
the colors conflict.
Use yellow as the background color instead: that should be an uncommon
terminal background, yet it's still ergonomic on both black and
white/grey terminals.
[ It would be a better solution to straight out detect color
collisions and resolve them reasonably by converting them to RGB and
calculating color space distances, but I was unable to find
proper documentation for SLtt_get_color_object() to recover the
current color scheme so I gave up ... Yellow works well enough. ]
Reported-and-Tested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Binderman <dcb314@hotmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20150305103213.GA23046@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The Alienware 17 (2015) has the same card and pin configuration of the
Alienware 15, so the same quirks must be applied.
Signed-off-by: Gabriele Martino <g.martino@gmx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fail with error when no DMA controller is set.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In checking fixes for of_irq_find_parent declaration location, I found
that of_msi_map_rid is also wrong. of_msi_map_rid is not implemented for
Sparc, so it should not be in the Sparc specific section of the header.
Move it to just depend on OF_IRQ.
Cc: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Common MVEBU pinctrl driver core gets an array of controls to modify
a specific set of registers and an array of modes for each pingroup
from each of the different SoC families of MVEBU.
Some SoC families comprise different variants that differ in available
pingroups and also controls, but to ease driver development, we can
pass a variant mask to disable specific pingroups for some variants.
However, controls are limited to the true number of pinctrl groups
avaiable on a variant.
Now, when pinctrl core driver parses over above arrays, it tries to
match modes with available controls and complains about missing
controls for modes that are passed to the core but actually are not
avaiable on a variant with:
kirkwood-pinctrl f1010000.pin-controller: unknown pinctrl group 36
This warning is a false-positive and annoying, so move the warning
after we checked the variant mask for each mode setting. Also, if
there is no supported setting for this variant, do not complain at
all.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reported-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The variable 'u64 *u64' should be only visible on 64-BIT platform.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
of_irq_find_parent was made static since it had no users outside of
of_irq.c. Export it again since we are going to use it again.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
[robh: move of_irq_find_parent to correct ifdef section]
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Lenovo Thinkpad T440s suffers from constant background noises, and it
seems to be a generic hardware issue on this model:
https://forums.lenovo.com/t5/ThinkPad-T400-T500-and-newer-T/T440s-speaker-noise/td-p/1339883
As the noise comes from the analog loopback path, disabling the path
is the easy workaround.
Also, the machine gives significant cracking noises at PM suspend. A
workaround found by trial-and-error is to disable the shutup callback
currently used for ALC269-variant.
This patch addresses these noise issues by introducing a new fixup
chain. Although the same workaround might be applicable to other
Thinkpad models, it's applied only to T440s (17aa:220c) in this patch,
so far, just to be safe (you chicken!). As a compromise, a new model
option string "tp440" is provided now, though, so that owners of other
Thinkpad models can test it more easily.
Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=958504
Reported-and-tested-by: Tim Hardeck <thardeck@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Running with CONFIG_DEBUG_SPINLOCK=y can trigger a BUG with the new IRQ
stack code:
BUG: spinlock lockup suspected on CPU#1
This is due to the IRQ_STACK_TO_TASK_STACK macro incorrectly retrieving
the task stack pointer stashed at the top of the IRQ stack.
Sayeth James:
| Yup, this is what is happening. Its an off-by-one due to broken
| thinking about how the stack works. My broken thinking was:
|
| > top ------------
| > | dummy_lr | <- irq_stack_ptr
| > ------------
| > | x29 |
| > ------------
| > | x19 | <- irq_stack_ptr - 0x10
| > ------------
| > | xzr |
| > ------------
|
| But the stack-pointer is decreased before use. So it actually looks
| like this:
|
| > ------------
| > | | <- irq_stack_ptr
| > top ------------
| > | dummy_lr |
| > ------------
| > | x29 | <- irq_stack_ptr - 0x10
| > ------------
| > | x19 |
| > ------------
| > | xzr | <- irq_stack_ptr - 0x20
| > ------------
|
| The value being used as the original stack is x29, which in all the
| tests is sp but without the current frames data, hence there are no
| missing frames in the output.
|
| Jungseok Lee picked it up with a 32bit user space because aarch32
| can't use x29, so it remains 0 forever. The fix he posted is correct.
This patch fixes the macro and adds some of this wisdom to a comment,
so that the layout of the IRQ stack is well understood.
Cc: James Morse <james.morse@arm.com>
Reported-by: Jungseok Lee <jungseoklee85@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Commit 3bfe049807c2403 ("netfilter: nfnetlink_{log,queue}:
Register pernet in first place") reorganised the initialisation
order of the pernet_subsys to avoid "use-before-initialised"
condition. However, in doing so the cleanup logic in nfnetlink_queue
got botched in that the pernet_subsys wasn't cleaned in case
nfnetlink_subsys_register failed. This patch adds the necessary
cleanup routine call.
Fixes: 3bfe049807c2403 ("netfilter: nfnetlink_{log,queue}: Register pernet in first place")
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Some ciphers actually support encrypting zero length plaintexts. For
example, many AEAD modes support this. The resulting ciphertext for
those winds up being only the authentication tag, which is a result of
the key, the iv, the additional data, and the fact that the plaintext
had zero length. The blkcipher constructors won't copy the IV to the
right place, however, when using a zero length input, resulting in
some significant problems when ciphers call their initialization
routines, only to find that the ->iv parameter is uninitialized. One
such example of this would be using chacha20poly1305 with a zero length
input, which then calls chacha20, which calls the key setup routine,
which eventually OOPSes due to the uninitialized ->iv member.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Otherwise check_timings fails and we get a "has no modes" message
from xrandr.
This fix makes the venc assume PAL and NTSC timings that match the
timings synthetized by copy_timings_drm_to_omap() from omapdrm
mode settings so that check_timings() succeeds.
Tested on: BeagleBoard XM, GTA04 and OpenPandora
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
If diu_ops is not implemented on platform, kernel will access a NULL
pointer. We need to check this pointer in DIU initialization.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Acked-by: Timur Tabi <timur@tabi.org>
Cc: stable@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
During driver probe, i2c_imx_init_recovery_info() must come before
i2c_add_numbered_adapter(), because the get/set_scl() functions
are assigned in i2c_register_adapter() under the conditon that bus
recover_info are initialized. Otherwise, get/set_scl() function
pointers never get assigned.
In such case, when i2c_generic_gpio_recovery() is used for bus recovery,
there will be kernel crash because bri->set_scl is NULL.
The solution to this bug is moving i2c_imx_init_recovery_info() before
i2c_register_adapter().
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
This patch makes the VCE IB test pass on Big-Endian systems. It converts
to little-endian the contents of the VCE message.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch fixes the VCE ring test when running on Big-Endian machines.
Every write to the ring needs to be translated to little-endian.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch makes the IB test on the GFX ring pass for CI-based cards
installed in Big-Endian machines.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Cc: stable@vger.kernel.org
|
|
git://people.freedesktop.org/~thomash/linux into drm-fixes
Pull request of 2015-12-08
A couple of fixes for vmwgfx. A WARN() fix by Dan Carpenter,
a TTM read/write lock imbalance causing occasional hangs with Wayland and
an implementation of cursor_set2 to fix incorrectly offset Wayland cursors.
* tag 'vmwgfx-fixes-4.4-151208' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Implement the cursor_set2 callback v2
drm/vmwgfx: fix a warning message
drm/ttm: Fixed a read/write lock imbalance
|
|
Just the one commit I mentioned earlier, making the PGOB workaround the
default.
* 'linux-4.4' of https://github.com/skeggsb/linux:
drm/nouveau/pmu: remove whitelist for PGOB-exit WAR, enable by default
|
|
The nps_enet driver happily mixes virtual, physical and __iomem
addresses, which are all different depending on the architecture
and configuration. That causes a warning when building the code
on ARM with LPAE mode enabled:
drivers/net/ethernet/ezchip/nps_enet.c: In function 'nps_enet_send_frame':
drivers/net/ethernet/ezchip/nps_enet.c:370:13: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
but will also fail to work for other reasons.
In this patch, I'm trying to change the code to use only normal
kernel pointers, which I assume is what the author actually meant:
* For reading or writing a 32-bit word that may be unaligned when
an SKB contains unaligned data, I'm using get_unaligned/put_unaligned()
rather than memcpy_fromio/toio.
* For converting a u8 pointer to a u32 pointer, I use a cast rather
than the incorrect virt_to_phys.
* For copying a couple of bytes from one place to another while respecting
alignment, I use memcpy instead of memcpy_toio.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pq_mdio driver can now be built for ARM64, where we get a format
string warning:
drivers/net/ethernet/freescale/fsl_pq_mdio.c: In function 'fsl_pq_mdio_probe':
drivers/net/ethernet/freescale/fsl_pq_mdio.c:467:25: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'long int' [-Wformat=]
The argument is an implicit ptrdiff_t from the subtraction of two pointers,
so we should use the %z format string modifier to make this work on 64-bit
architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: fe761bcb9046 ("net: fsl: expands dependencies of NET_VENDOR_FREESCALE")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an interface is brought up which was previously suspended (via
runtime PM), it would hang. This happens because napi_disable is called
before napi_enable.
Solve this by avoiding napi_enable in the resume during open function
(netif_running is true when open is called, IFF_UP is set after a
successful open; netif_running is false when close is called, but IFF_UP
is then still set).
While at it, remove WORK_ENABLE check from rtl8152_open (introduced with
the original change) because it cannot happen:
- After this patch, runtime resume will not set it during rtl8152_open.
- When link is up, rtl8152_open is not called.
- When link is down during system/auto suspend/resume, it is not set.
Fixes: 41cec84cf285 ("r8152: don't enable napi before rx ready")
Link: https://lkml.kernel.org/r/20151205105912.GA1766@al
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit bc69fdfc6c13
("net: thunderx: Enable BGX LMAC's RX/TX only after VF is up")
introduces lmac_cnt member and starts verifying VF number against it.
This is plain wrong, and works only because currently we have hardcoded
1:1 mapping between VFs and LMACs, and in this case num_vf_en and
lmac_cnt are always equal. However in future this may change, and the
code will badly misbehave. The worst consequence of this is failure to
deliver link status messages, causing VFs to go defunct because since
commit 0b72a9a1060e ("net: thunderx: Switchon carrier only upon
interface link up") VF will not fully bring itself up without it.
This patch fixes the potential problem by doing VF number checks against
the num_vf_en. Since lmac_cnt is not used anywhere else, it is removed.
Additionally some duplicated code is factored out into nic_enable_vf()
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
based upon the corresponding patch from Neil's March patchset,
again with kmap-related horrors removed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
more or less along the lines of Neil's patchset, sans the insanity
around kmap().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
new method: ->get_link(); replacement of ->follow_link(). The differences
are:
* inode and dentry are passed separately
* might be called both in RCU and non-RCU mode;
the former is indicated by passing it a NULL dentry.
* when called that way it isn't allowed to block
and should return ERR_PTR(-ECHILD) if it needs to be called
in non-RCU mode.
It's a flagday change - the old method is gone, all in-tree instances
converted. Conversion isn't hard; said that, so far very few instances
do not immediately bail out when called in RCU mode. That'll change
in the next commits.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
kmap() in page_follow_link_light() needed to go - allowing to hold
an arbitrary number of kmaps for long is a great way to deadlocking
the system.
new helper (inode_nohighmem(inode)) needs to be used for pagecache
symlinks inodes; done for all in-tree cases. page_follow_link_light()
instrumented to yell about anything missed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Call to iptunnel_xmit_stats() is not required after udp-tunnel6-xmit.
By calling iptunnel_xmit_stats() results in incorrect device stats.
Following patch drops this call.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
