| Age | Commit message (Collapse) | Author |
|---|
|
Some PHYs need the refclk to be a continuous clock. Therefore they don't
allow turning it off and on again during operation. Nonetheless such a
clock switching is performed by some ETH drivers (namely FEC [1]) for
power saving reasons. An example for an affected PHY is the
SMSC/Microchip LAN8720 in "REF_CLK In Mode".
In order to provide a uniform method to overcome this problem this patch
adds a new phy_driver flag (PHY_RST_AFTER_CLK_EN) and corresponding
function phy_reset_after_clk_enable() to the phylib. These should be
used to trigger reset of the PHY after the refclk is switched on again.
[1] commit e8fcfcd5684a ("net: fec: optimize the clock management to save power")
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some PHYs need a minimum time after the reset gpio was asserted and/or
deasserted. To ensure we meet these timing requirements add two new
optional devicetree parameters for the phy: reset-delay-us and
reset-post-delay-us.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit fbf3d034f2ff6264183cfa6845770e8cc2a986c8.
As of commit 560869100b99a3da ("clk: renesas: cpg-mssr: Restore module
clocks during resume"), the workaround is no longer needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Antoine Tenart says:
====================
net: mvpp2: various improvements
These patches are sent as a series to avoid any possible conflict, even
though there're not entirely related. I can send them separately if
needed. The series applies on today's net-next tree.
Since v1:
- Removed the patch disabling TSO on allocation errors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adjust the coalescing parameters to the vendor
recommendations for the PPv2 network controller.
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the tx-usec value to the informations reported to
ethtool by the get_coalesce function.
Suggested-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cosmetic patch aligning values in the ethtool get_coalesce function.
This patch do not modify in anyway the driver's behaviour.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Rx/Tx ring sizes can be adjusted thanks to ethtool given specific
network needs. This commit splits the default ring size from its max
value to allow ethtool to vary the parameters in both ways.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a check to only free the TSO header buffer when its
allocation previously succeeded.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a set of values in the drm_display_info structure for each
connector which hold information derived from EDID. These are computed
in drm_add_display_info. Before this patch, that was only called in
drm_add_edid_modes. This meant that they were only set when EDID was
present and never reset when EDID was not, as happened when the
display was disconnected.
One of these fields, non_desktop, is used from
drm_mode_connector_update_edid_property, the function responsible for
assigning the new edid value to the application-visible property.
Various drivers call these two functions (drm_add_edid_modes and
drm_mode_connector_update_edid_property) in different orders. This
means that even when EDID is present, the drm_display_info fields may
not have been computed at the time that
drm_mode_connector_update_edid_property used the non_desktop value to
set the non_desktop property.
I've added a public function (drm_reset_display_info) that resets the
drm_display_info field values to default values and then made the
drm_add_display_info function public. These two functions are now
called directly from drm_mode_connector_update_edid_property so that
the drm_display_info fields are always computed from the current EDID
information before being used in that function.
This means that the drm_display_info values are often computed twice,
once when the EDID property it set and a second time when EDID is used
to compute modes for the device. The alternative would be to uniformly
ensure that the values were computed once before being used, which
would require that all drivers reliably invoke the two paths in the
same order. The computation is inexpensive enough that it seems more
maintainable in the long term to simply compute them in both paths.
The API to drm_add_display_info has been changed so that it no longer
takes the set of edid-based quirks as a parameter. Rather, it now
computes those quirks itself and returns them for further use by
drm_add_edid_modes.
This patch also includes a number of 'const' additions caused by
drm_mode_connector_update_edid_property taking a 'const struct edid *'
parameter and wanting to pass that along to drm_add_display_info.
v2: after review by Daniel Vetter <daniel.vetter@ffwll.ch>
Removed EXPORT_SYMBOL_GPL for drm_reset_display_info and
drm_add_display_info.
Added FIXME in drm_mode_connector_update_edid_property about
potentially merging that with drm_add_edid_modes to avoid
the need for two driver calls.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171213084427.31199-1-keithp@keithp.com
(danvet: cherry picked from commit 12a889bf4bca ("drm: rework delayed
connector cleanup in connector_iter") from drm-misc-next since
functional conflict with changes in -next and we need to make sure
both have the right version and nothing gets lost.)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The driver may sleep in the interrupt handler.
The function call path is:
bluecard_interrupt (interrupt handler)
bluecard_write_wakeup
schedule_timeout --> may sleep
To fix it, schedule_timeout is replaced with mdelay.
This bug is found by my static analysis tool(DSAC) and checked by my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
A malicious USB device with crafted descriptors can cause the kernel
to access unallocated memory by setting the bNumInterfaces value too
high in a configuration descriptor. Although the value is adjusted
during parsing, this adjustment is skipped in one of the error return
paths.
This patch prevents the problem by setting bNumInterfaces to 0
initially. The existing code already sets it to the proper value
after parsing is complete.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 32fd87b3bbf5f7a045546401dfe2894dbbf4d8c3.
Alan wrote a better fix for this...
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit:
681fbec881de ("lockdep: Use consistent printing primitives")
has moved lockdep away from using printk() for printing.
The commit added usage of pr_cont() which wasn't wrapped in the
userspace headers, causing the following warning for the
liblockdep build:
../../../kernel/locking/lockdep.c:3544:2: warning: implicit declaration of function 'pr_cont' [-Wimplicit-function-declaration]
Adding an empty declaration of 'pr_cont' fixes the problem.
Signed-off-by: Mengting Zhang <zhangmengting@huawei.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: a.p.zijlstra@chello.nl
Link: http://lkml.kernel.org/r/20171212181644.11913-2-alexander.levin@verizon.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
do_sea() calls arm64_notify_die() which will always signal
user-space. It also returns whether APEI claimed the external
abort as a RAS notification. If it returns failure do_mem_abort()
will signal user-space too.
do_mem_abort() wants to know if we handled the error, we always
call arm64_notify_die() so can always return success.
Signed-off-by: Dongjiu Geng <gengdongjiu@huawei.com>
Reviewed-by: James Morse <james.morse@arm.com>
Reviewed-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
So far, kernel did not allow to advertise when there was a connection
established. With this patch kernel does allow it if controller
supports it.
If controller supports non-connectable advertising when connected, then
only non-connectable advertising instances will be advertised.
Signed-off-by: Łukasz Rymanowski <lukasz.rymanowski@codecoup.pl>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds the "ti,cc2560" compatible string for a TI CC2560 chip.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds a compatible string for the Texas Instruments CC2560 Bluetooth
chip to the existing TI WiLink shared transport bindings. These chips are
similar enough that the same bindings work for both. The file is renamed
to ti-bluetooth.txt to make it more generic.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds an optional nvmem consumer to get a BD address from an external
source. The BD address is then set in the Bluetooth chip after the
firmware has been loaded.
This has been tested working with a TI CC2560A chip (in a LEGO MINDSTORMS
EV3).
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
- Correct an error in the evdev protocol in asus-wireless which results
in dropped key events in recent versions of libinput
- Add a quirk for keyboard lighting for a specific Dell laptop
- Silence a static analysis warning regarding unchecked return values
of small kmalloc() allocations in dell-wmi
* tag 'platform-drivers-x86-v4.15-3' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: dell-wmi: check for kmalloc() errors
platform/x86: asus-wireless: send an EV_SYN/SYN_REPORT between state changes
platform/x86: dell-laptop: Fix keyboard max lighting for Dell Latitude E6410
|
|
This adds optional nvmem consumer properties to the ti,wlink-st device tree
bindings to allow specifying the BD address.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds support for setting the public address on Texas Instruments
Bluetooth chips using a vendor-specific command.
This has been tested on a CC2560A chip. The TI wiki also indicates that
this command should work on TI WL17xx/WL18xx Bluetooth chips.
During review, there was some question as to the correctness of the byte
swapping since TI's documentation is not clear on this matter. This can
be tested with the btmgmt utility from bluez. The adapter must be powered
off to change the address. If the baswap() is omitted, address is reversed.
In case there is a issue in the future, here is the output of btmon during
the command `btmgmt public-addr 00:11:22:33:44:55`:
Bluetooth monitor ver 5.43
= Note: Linux version 4.15.0-rc2-08561-gcb132a1-dirty (armv5tejl) 0.707043
= Note: Bluetooth subsystem version 2.22 0.707091
= New Index: 00:17:E7:BD:1C:8E (Primary,UART,hci0) [hci0] 0.707106
@ MGMT Open: btmgmt (privileged) version 1.14 {0x0002} 0.707124
@ MGMT Open: bluetoothd (privileged) version 1.14 {0x0001} 0.707137
@ MGMT Open: btmon (privileged) version 1.14 {0x0003} 0.707540
@ MGMT Command: Set Public Address (0x0039) plen 6 {0x0002} [hci0] 11.167991
Address: 00:11:22:33:44:55 (CIMSYS Inc)
@ MGMT Event: Command Complete (0x0001) plen 7 {0x0002} [hci0] 11.175681
Set Public Address (0x0039) plen 4
Status: Success (0x00)
Missing options: 0x00000000
@ MGMT Event: Index Removed (0x0005) plen 0 {0x0003} [hci0] 11.175757
@ MGMT Event: Index Removed (0x0005) plen 0 {0x0002} [hci0] 11.175757
@ MGMT Event: Index Removed (0x0005) plen 0 {0x0001} [hci0] 11.175757
= Open Index: 00:17:E7:BD:1C:8E [hci0] 11.176807
< HCI Command: Vendor (0x3f|0x0006) plen 6 [hci0] 11.176975
00 11 22 33 44 55 .."3DU
> HCI Event: Command Complete (0x0e) plen 4 [hci0] 11.188260
Vendor (0x3f|0x0006) ncmd 1
Status: Success (0x00)
...
< HCI Command: Read Local Version Info.. (0x04|0x0001) plen 0 [hci0] 11.189859
> HCI Event: Command Complete (0x0e) plen 12 [hci0] 11.190732
Read Local Version Information (0x04|0x0001) ncmd 1
Status: Success (0x00)
HCI version: Bluetooth 2.1 (0x04) - Revision 0 (0x0000)
LMP version: Bluetooth 2.1 (0x04) - Subversion 6431 (0x191f)
Manufacturer: Texas Instruments Inc. (13)
< HCI Command: Read BD ADDR (0x04|0x0009) plen 0 [hci0] 11.191027
> HCI Event: Command Complete (0x0e) plen 10 [hci0] 11.192101
Read BD ADDR (0x04|0x0009) ncmd 1
Status: Success (0x00)
Address: 00:11:22:33:44:55 (CIMSYS Inc)
...
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
There is already __hci_req_disable_advertising() function for disabling,
so use it.
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Instead of open coding byte-by-byte printing, re-use %*ph specifier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds an endianness conversion when setting the baudrate using a
vendor-specific command. Otherwise, bad things might happen on a big-
endian system.
Suggested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds a #define for the vendor-specific HCI command to set the
baudrate instead of using the bare 0xff36 multiple times.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When a TI Bluetooth chip is reset, it takes about 100ms for the RTS line of
the chip to deassert. For my use case with a TI CC2560A chip, this delay
was not long enough and caused the local UART to never transmit at all (TI
AM1808 SoC UART2).
We can wait for the CTS signal using serdev_device_wait_for_cts() instead
of trying to guess using msleep().
Also changed the comment to be more informative while we are touching this
code.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The bt_* printk macros include a \n already, so we don't need extra ones
here.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
BCM43341 devices soldered onto the PCB (non-removable) always (AFAICT)
use an UART connection for bluetooth. But they also advertise btsdio
support on their 3th sdio function, this causes 2 problems:
1) A non functioning BT HCI getting registered
2) Since the btsdio driver does not have suspend/resume callbacks,
mmc_sdio_pre_suspend will return -ENOSYS, causing mmc_pm_notify()
to react as if the SDIO-card is removed and since the slot is
marked as non-removable it will never get detected as inserted again.
Which results in wifi no longer working after a suspend/resume.
This commit fixes both by making btsdio ignore BCM43341 devices
when connected to a slot which is marked non-removable.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Asus T100HA laptop uses an ACPI HID of BCM2E72 for the bluetooth
part of the SDIO bcm43340 wifi/bt combo chip.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In case of hci send frame failure, skb is still owned
by the caller (hci_core) and then should not be freed.
This fixes crash on dragonboard-410c when sending SCO
packet. skb is freed by both btqcomsmd and hci_core.
Fixes: 1511cc750c3d ("Bluetooth: Introduce Qualcomm WCNSS SMD based HCI driver")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
John Stultz reports a boot time crash with the HiKey board (which uses
hci_serdev) occurring in hci_uart_tx_wakeup(). That function is
contained in hci_ldisc.c, but also called from the newer hci_serdev.c.
It acquires the proto_lock in struct hci_uart and it turns out that we
forgot to init the lock in the serdev code path, thus causing the crash.
John bisected the crash to commit 67d2f8781b9f ("Bluetooth: hci_ldisc:
Allow sleeping while proto locks are held"), but the issue was present
before and the commit merely exposed it. (Perhaps by luck, the crash
did not occur with rwlocks.)
Init the proto_lock in the serdev code path to avoid the oops.
Stack trace for posterity:
Unable to handle kernel read from unreadable memory at 406f127000
[000000406f127000] user address but active_mm is swapper
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Hardware name: HiKey Development Board (DT)
Call trace:
hci_uart_tx_wakeup+0x38/0x148
hci_uart_send_frame+0x28/0x38
hci_send_frame+0x64/0xc0
hci_cmd_work+0x98/0x110
process_one_work+0x134/0x330
worker_thread+0x130/0x468
kthread+0xf8/0x128
ret_from_fork+0x10/0x18
Link: https://lkml.org/lkml/2017/11/15/908
Reported-and-tested-by: John Stultz <john.stultz@linaro.org>
Cc: Ronald Tschalär <ronald@innovation.ch>
Cc: Rob Herring <rob.herring@linaro.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Fix: drivers/bluetooth/Kconfig:35:warning: multi-line strings not
supported warning.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
On many laptops the btusb device is the only USB device not having USB
autosuspend enabled, this causes not only the HCI but also the USB
controller to stay awake, together using aprox. 0.4W of power.
Modern ultrabooks idle around 6W (at 50% screen brightness), 3.5W for
Apollo Lake devices. 0.4W is a significant chunk of this (7 / 11%).
The btusb driver already contains code to allow enabling USB autosuspend,
but currently leaves it up to the user / userspace to enable it. This
means that for most people it will not be enabled, leading to an
unnecessarily high power consumption.
Since enabling it is not entirely without risk of regressions, this
commit adds a Kconfig option so that Linux distributions can choose to
enable it by default. This commit also adds a module option so that when
distros receive bugs they can easily ask the user to disable it again
for easy debugging.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
* Improve jump targets so that a bit of exception handling can be better
reused at the end of this function.
* Adjust five condition checks.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Assuming that the original code idea was to enable in-band sleeping
only if the setup_rome method returns succes and run in 'standard'
mode otherwise, we should not return setup_rome return value which
makes qca_setup fail if no rampatch/nvm file found.
This fixes BT issue on the dragonboard-820C p4 which includes the
following QCA controller:
hci0: Product:0x00000008
hci0: Patch :0x00000111
hci0: ROM :0x00000302
hci0: SOC :0x00000044
Since there is no rampatch for this controller revision, just make
it work as is.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
It's been sometime I'm not involved in Bluetooth anymore but I never
got around to remove my name from it. Doing it now.
Thanks for all the fish! :)
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
While using large percpu maps, htab_map_alloc() can hold
cpu for hundreds of ms.
This patch adds cond_resched() calls to percpu alloc/free
call sites, all running in process context.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
The port number shift is still hard-coded to 1 while it now depends
on the hardware.
Thankfully 0 is always 0 no matter how you shift it, so this was a
bug without consequences.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 0fe16195f891 ("i2c: piix4: Fix SMBus port selection for AMD Family 17h chips")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Uniformize STMicroelectronics copyrights headers and add SPDX
identifier.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Acked-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-current
Sakari fixed a regression introduced during the 4.15 merge window and
David submitted a fix for an issue that has existed in at24 since
introducing nvmem.
|
|
This reverts commit b07815d4eaf658b683c345d6e643895a20d92f29.
The reverted commit was merged into v4-15-rc1 by mistake: it was taken
from the IMX tree but the patch has never been sent to linux-mtd nor
reviewed by any spi-nor maintainers.
Actually, it would have been rejected since we add new values for the
'compatible' DT property only for SPI NOR memories that don't support
the JEDEC READ ID op code (0x9F).
Both en25s64 and sst25wf040b support the JEDEC READ ID op code, hence
should use the "jedec,spi-nor" string alone as 'compatible' value.
See the following link for more details:
http://lists.infradead.org/pipermail/linux-mtd/2017-November/077425.html
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
|
|
Daniel Borkmann says:
====================
Couple of outstanding fixes for BPF tree: 1) fixes a perf RB
corruption, 2) and 3) fixes a few build issues from the recent
bpf_perf_event.h uapi corrections. Thanks!
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
At least on x86_64, the kernel's BPF selftests seemed to have stopped
to build due to 618e165b2a8e ("selftests/bpf: sync kernel headers and
introduce arch support in Makefile"):
[...]
In file included from test_verifier.c:29:0:
../../../include/uapi/linux/bpf_perf_event.h:11:32:
fatal error: asm/bpf_perf_event.h: No such file or directory
#include <asm/bpf_perf_event.h>
^
compilation terminated.
[...]
While pulling in tools/arch/*/include/uapi/asm/bpf_perf_event.h seems
to work fine, there's no automated fall-back logic right now that would
do the same out of tools/include/uapi/asm-generic/bpf_perf_event.h. The
usual convention today is to add a include/[uapi/]asm/ equivalent that
would pull in the correct arch header or generic one as fall-back, all
ifdef'ed based on compiler target definition. It's similarly done also
in other cases such as tools/include/asm/barrier.h, thus adapt the same
here.
Fixes: 618e165b2a8e ("selftests/bpf: sync kernel headers and introduce arch support in Makefile")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Since c895f6f703ad ("bpf: correct broken uapi for
BPF_PROG_TYPE_PERF_EVENT program type") um (uml) won't build
on i386 or x86_64:
[...]
CC init/main.o
In file included from ../include/linux/perf_event.h:18:0,
from ../include/linux/trace_events.h:10,
from ../include/trace/syscall.h:7,
from ../include/linux/syscalls.h:82,
from ../init/main.c:20:
../include/uapi/linux/bpf_perf_event.h:11:32: fatal error:
asm/bpf_perf_event.h: No such file or directory #include
<asm/bpf_perf_event.h>
[...]
Lets add missing bpf_perf_event.h also to um arch. This seems
to be the only one still missing.
Fixes: c895f6f703ad ("bpf: correct broken uapi for BPF_PROG_TYPE_PERF_EVENT program type")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Richard Weinberger <richard@sigma-star.at>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Richard Weinberger <richard@sigma-star.at>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
When tracing and networking programs are both attached in the
system and both use event-output helpers that eventually call
into perf_event_output(), then we could end up in a situation
where the tracing attached program runs in user context while
a cls_bpf program is triggered on that same CPU out of softirq
context.
Since both rely on the same per-cpu perf_sample_data, we could
potentially corrupt it. This can only ever happen in a combination
of the two types; all tracing programs use a bpf_prog_active
counter to bail out in case a program is already running on
that CPU out of a different context. XDP and cls_bpf programs
by themselves don't have this issue as they run in the same
context only. Therefore, split both perf_sample_data so they
cannot be accessed from each other.
Fixes: 20b9d7ac4852 ("bpf: avoid excessive stack usage for perf_sample_data")
Reported-by: Alexei Starovoitov <ast@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Song Liu <songliubraving@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Josef Bacik says:
====================
This is the same as v8, just rebased onto the bpf tree.
v8->v9:
- rebased onto the bpf tree.
v7->v8:
- removed the _ASM_KPROBE_ERROR_INJECT since it was not needed.
v6->v7:
- moved the opt-in macro to bpf.h out of kprobes.h.
v5->v6:
- add BPF_ALLOW_ERROR_INJECTION() tagging for functions that will support this
feature. This way only functions that opt-in will be allowed to be
overridden.
- added a btrfs patch to allow error injection for open_ctree() so that the bpf
sample actually works.
v4->v5:
- disallow kprobe_override programs from being put in the prog map array so we
don't tail call into something we didn't check. This allows us to make the
normal path still fast without a bunch of percpu operations.
v3->v4:
- fix a build error found by kbuild test bot (I didn't wait long enough
apparently.)
- Added a warning message as per Daniels suggestion.
v2->v3:
- added a ->kprobe_override flag to bpf_prog.
- added some sanity checks to disallow attaching bpf progs that have
->kprobe_override set that aren't for ftrace kprobes.
- added the trace_kprobe_ftrace helper to check if the trace_event_call is a
ftrace kprobe.
- renamed bpf_kprobe_state to bpf_kprobe_override, fixed it so we only read this
value in the kprobe path, and thus only write to it if we're overriding or
clearing the override.
v1->v2:
- moved things around to make sure that bpf_override_return could really only be
used for an ftrace kprobe.
- killed the special return values from trace_call_bpf.
- renamed pc_modified to bpf_kprobe_state so bpf_override_return could tell if
it was being called from an ftrace kprobe context.
- reworked the logic in kprobe_perf_func to take advantage of bpf_kprobe_state.
- updated the test as per Alexei's review.
- Original message -
A lot of our error paths are not well tested because we have no good way of
injecting errors generically. Some subystems (block, memory) have ways to
inject errors, but they are random so it's hard to get reproduceable results.
With BPF we can add determinism to our error injection. We can use kprobes and
other things to verify we are injecting errors at the exact case we are trying
to test. This patch gives us the tool to actual do the error injection part.
It is very simple, we just set the return value of the pt_regs we're given to
whatever we provide, and then override the PC with a dummy function that simply
returns.
Right now this only works on x86, but it would be simple enough to expand to
other architectures. Thanks,
Josef
====================
In patch "bpf: add a bpf_override_function helper" Alexei moved
"ifdef CONFIG_BPF_KPROBE_OVERRIDE" few lines to fail program loading
when kprobe_override is not available instead of failing at run-time.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This was instrumental in reproducing a space cache bug.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This adds a basic test for bpf_override_return to verify it works. We
override the main function for mounting a btrfs fs so it'll return
-ENOMEM and then make sure that trying to mount a btrfs fs will fail.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Error injection is sloppy and very ad-hoc. BPF could fill this niche
perfectly with it's kprobe functionality. We could make sure errors are
only triggered in specific call chains that we care about with very
specific situations. Accomplish this with the bpf_override_funciton
helper. This will modify the probe'd callers return value to the
specified value and set the PC to an override function that simply
returns, bypassing the originally probed function. This gives us a nice
clean way to implement systematic error injection for all of our code
paths.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
