| Age | Commit message (Collapse) | Author |
|---|
|
Some register settings must be applied before the first time low power
sleep mode is entered on the wm5110 to ensure optimium performance.
These settings require SYSCLK to be enabled whilst they are being
applied. This patch applies the settings using the recently factored out
boot time SYSCLK functionality.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
wm5102 applies a custom hardware boot sequence, for this the SYSCLK
needs to be enabled. This patch factors out the code that enables
SYSCLK for this sequence such that it can be used for other boot time
operations that require SYSCLK.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
In preparation for some refactoring fixup some minor style, formating
and code clarity issues.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The wm5102 uses a custom boot sequence and the standard boot sequence is
disabled. However, the standard boot sequence must be run at least once
after a cold boot (caused by either a hard reset or removal of AVDD).
Unfortunately the register WRITE_SEQUENCER_CTRL_3 is not affected by the
hardware reset. This means if the device has been previously booted but
the AVDD supply has never been removed, arizona_dev_init will reset the
chip but the boot sequence will not run, which can cause numerous
problems. The solution is to manually clear this register and then boot
the chip again, which is what this patch does.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds functions for enabling and disabling the physical reset
line. This will be helpful in future refactoring.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This also handily fixes a leak of the GPIO in arizona_dev_exit.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The System Configuration (syscon) driver is an important one, which
effects many ARM-SoC based platforms. I'm adding Arnd as a primary
reviewer as he is highly competent in this area and has a keen
interest in ARM-SoC.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Extend the entry for Samsung MFD drivers for PMIC devices (Power
Management Integrated Circuit) with bindings documentation, clock
(clk-s2mps11.c) and RTC drivers (rtc-s5m.c).
These PMIC devices are used on many Exynos-based boards like Arndale
Octa (S2MPS11), Gear 2 (S2MPS14).
Add Krzysztof Kozlowski as a supporter for reviewing them.
I am not the author of these drivers. However I have recently
contributed to most of them and I have access to datasheets and hardware.
Cc: Sangbeom Kim <sbkim73@samsung.com>
CC: Mike Turquette <mturquette@linaro.org>
CC: Stephen Boyd <sboyd@codeaurora.org>
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Alexandre Belloni <alexandre.belloni@free-electrons.com>
CC: Liam Girdwood <lgirdwood@gmail.com>
CC: Mark Brown <broonie@kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The defined struct max77686_opmode_data isn't used neither by
the max77686 mfd driver nor the drivers for its sub-devices.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
I noticed the PMIC configuration on 37xx-evm won't actually shut down
the voltages during off-idle. Turns out 37xx-evm needs the AC charger
state transitions disabled like we are doing for SDP and LDP in the
legacy booting case.
Let's fix this for device tree based booting by setting up the quirk
flag based on the compatible flag. And let's also use the existing
define for STARTON_CHG.
Note that SDP and EVM do not have the PMIC clken wired to gate the
the oscillator while LDP has.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Fix typo in 'Multifunction'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This soft reset used to be located after the register patch had been
applied, but has since moved to before the patch is applied. At the new
location there is no requirement to do a register sync as no register
writes will have happened yet.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds device tree binding documentation for
the flash cell of the Maxim max77693 multifunctional device.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Constify in various drivers configuration data which is not modified:
- regmap_irq_chip,
- individual regmap_irq's in array,
- regmap_config,
- irq_domain_ops,
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
'ib-mfd-i2c-input-chrome-4.2' into ibs-for-mfd-merged
|
|
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
On some board, TE GPIO should be configured properly thoughout pinctrl driver
as an wakeup interrupt. So this gpio should be configurable in the board's DT,
not being requested as a input pin.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
MIC must be initilized by MIPI DSI when it is being bound.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch adds support for Exynos5433 mipi dsi.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch make the driver to use an array for clock access. The number
of clocks are different from the existing MIPI DSI driver and Exynos5433
MIPI DSI driver. So this patch is needed before adding support for
Exynos5433 MIPI DSI driver.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Exynos MIPI DSI driver uses some static values such as address offsets,
register setting values, and etc. This patch makes the driver get those
values from the driver data.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch adds macros for register writing/reading. This is needed for
adding support Exynos5433 MIPI DSI driver, not by using if statement, but
by using driver data.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch renames pll_clk to sclk_clk. The clock referenced by pll_clk
is actually not the pll input clock for dsi. The pll input clock comes
from the board's oscillator directly. But for the backward
compatibility, the old clock name "pll_clk" is also OK.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
MIC(Mobile image compressor) is newly added IP in Exynos5433. MIC
resides between decon and mipi dsim, and compresses frame data by 50%.
With dsi, not display port, to send frame data to the panel, the
bandwidth is not enough. That is why this compressor is introduced.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
When there are multiple ports or multiple endpoints in a port, they have to be
distinguished by the value of reg property. It is common. The drivers can get
the specific endpoint in the specific port via this function. Now the drivers
have to implement this code in themselves or have to force the order of dt nodes
to get the right node.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
DECON(Display and Enhancement Controller) is new IP replacing FIMD in
Exynos5433. This patch adds Exynos5433 decon driver.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
'regulator/topic/qcom' and 'regulator/topic/soft-start' into regulator-next
|
|
'regulator/topic/max14577', 'regulator/topic/max77693', 'regulator/topic/max77843' and 'regulator/topic/max8973' into regulator-next
|
|
'regulator/topic/doc', 'regulator/topic/fan53555', 'regulator/topic/gpio' and 'regulator/topic/ilim' into regulator-next
|
|
'regulator/topic/arizona', 'regulator/topic/cleanup' and 'regulator/topic/da9062' into regulator-next
|
|
|
|
and 'regulator/fix/wm831x' into regulator-linus
|
|
|
|
|
|
|
|
ASoC: Further updates for v4.2
There's a bunch of additional updates and fixes that came in since my
orignal pull request here, including DT support for rt5645 and fairly
large serieses of cleanups and improvements to tas2552 and rcar.
# gpg: Signature made Mon 22 Jun 2015 10:24:48 BST using RSA key ID 5D5487D0
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
|
|
ASoC: Updates for v4.2
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
# gpg: Signature made Mon 08 Jun 2015 18:48:37 BST using RSA key ID 5D5487D0
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
|
|
'asoc/fix/wm8955' and 'asoc/fix/wm8960' into asoc-linus
|
|
'asoc/fix/intel', 'asoc/fix/max98925', 'asoc/fix/rcar' and 'asoc/fix/ux500' into asoc-linus
|
|
|
|
This patch is a preparation patch for adding support for Exynos5433
DECON. Exynos7 DECON have to be distinguished from Exynos5433 DECON.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Every CRTC drivers in Exynos DRM implements the code which checks
whether IOMMU is supported or not, and if supported enable it.
Making new helper for it generalize each CRTC drivers.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Without this dependency, Kbuild is confused and the configs below
them are not placed under Exynos DRM. This patch fixes it, so the
configs below them become to be placed under Exynos DRM.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This dependency is a historical thing. It is added when this DP driver is
under media subsystem. Now because it is under Exynos DRM, this dependency
is not needed anymore.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Further updates for v4.2
There's a bunch of additional updates and fixes that came in since my
orignal pull request here, including DT support for rt5645 and fairly
large serieses of cleanups and improvements to tas2552 and rcar.
|
|
|
|
into asoc-next
|
|
|
|
|
