| Age | Commit message (Collapse) | Author |
|---|
|
Currently, firmware does not like when beacon mode is set as staggered
mode for more than one beaconing vifs. Beacon mode for multiple
beaconing (transmitted) vifs are expected to be in burst mode. So set
beacon mode to burst mode by default.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sidhanta Sahu <quic_sidhanta@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230905213943.12275-1-quic_sidhanta@quicinc.com
|
|
Mac80211 does not set flags BSS_CHANGED_FILS_DISCOVERY and
BSS_CHANGED_UNSOL_BCAST_PROBE_RESP if there are no updates to
FILS discovery and unsolicited broadcast probe response transmission
configurations respectively. For BSS change operations such as channel
switch, this results in the transmissions getting stopped because the
driver does not send WMI command to firmware if the flags are not set.
Remove the checks for the flags to always send the existing
configuration to firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230905174324.25296-1-quic_alokad@quicinc.com
|
|
No need cast (void *) to (struct ath11k_base *),
struct hal_rx_msdu_link *), (struct ath11k_buffer_addr *) or
other types.
Signed-off-by: Wu Yunchuan <yunchuan@nfschina.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230919045150.524304-1-yunchuan@nfschina.com
|
|
Currently mac80211 will send 3 scan request for each scan of WCN7850, they
are 2.4 GHz/5 GHz/6 GHz band scan. Firmware of WCN7850 will cache the RNR
IE(Reduced Neighbor Report element) which exist in the beacon of 2.4 GHz/5
GHz of the AP which is co-located with 6 GHz, and then use the cache to
scan in 6 GHz band scan if the 6 GHz scan is in the same scan with the 2.4
GHz/5 GHz band, this will helpful to search more AP of 6 GHz. Also it will
decrease the time cost of scan because firmware will use dual-band scan
for the 2.4 GHz/5 GHz, it means the 2.4 GHz and 5 GHz scans are doing
simultaneously.
Set the flag IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS for WCN7850 since it
supports 2.4 GHz/5 GHz/6 GHz in a single wiphy/ieee80211_hw.
This does not impact QCN9274, because it is not single_phy, so does not
have 2.4 GHz/5 GHz/6 GHz in the same wiphy, then it does not match the
condition and then IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS will not set for
QCN9274.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230913105507.17675-1-quic_wgong@quicinc.com
|
|
Some firmware versions for WCN7850 report the default regdomain with
alpha code "na" by default when load as a world wide regdomain,
ath12k should treat it as a world wide alpha code.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230906090355.19181-1-quic_wgong@quicinc.com
|
|
ath12k prints "Received scan event for unknown vdev" when doing the
following test:
1. trigger scan
2. wait 0.2 second
3. iw reg set is issued or 11d scan complete event is sent from firmware
Reason is:
When iw reg set is issues or the 11d scan complete event is received, the
new country code will be set to the firmware, and the new regdomain info
indicated to ath12k, then the new channel list will be sent to the firmware.
The firmware will cancel the current scan after receiving WMI_SCAN_CHAN_LIST_CMDID
which is used for the new channel list, and the state of ath12k is
ATH12K_SCAN_RUNNING, then ath12k_get_ar_on_scan_abort() returns NULL and
ath12k_scan_event() returns at this point and does not indicate scan
completion to mac80211.
Indicate scan completion to mac80211 and get rid of the "Received scan
event for unknown vdev" print for the above case.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230906085746.18968-1-quic_wgong@quicinc.com
|
|
ATH12K_SCAN_STARTING state
Scan failure can not be recovered from when running a loop of the
following steps:
1. run scan: "iw wlan scan".
2. run command: echo assert > /sys/kernel/debug/ath12k/wcn7850\ hw2.0/simulate_fw_crash
immediately after step 1.
result:
scan failed and can not recover even when wlan recovery succeeds:
command failed: Device or resource busy (-16)
reason:
When scan arrives, WMI_START_SCAN_CMDID is sent to the firmware and
function ath12k_mac_op_hw_scan() returns, then simulate_fw_crash arrives
and the scan started event does not arrive, and then it starts to do
recovery of wlan. __ath12k_mac_scan_finish() which is called from
ath12k_core_halt() is one step of recovery, it will not call
ieee80211_scan_completed() by logic currently because the scan state is
ATH12K_SCAN_STARTING. Thus it leads the scan not being completed in
mac80211, and leads all consecutive scans failing with -EBUSY in
nl80211_trigger_scan even after wlan recovery success.
Indicate scan complete with aborted flag to mac80211 for
ATH12K_SCAN_STARTING to allow recovery from scan failed with "Device or
resource busy (-16)" after wlan recovery.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230905105947.10369-1-quic_wgong@quicinc.com
|
|
When firmware crashed while channel switch running, recovery starts in
ath12k. Then ieee80211_sta_connection_lost() will be called by function
ieee80211_restart_work() in mac80211. And then many WMI command timeout
because firmware is crashed. Each WMI command cost 3 seconds, then the
total time will be large and leads recovery fail.
Hence change to set value ATH12K_FLAG_CRASH_FLUSH early and then
ath12k_wmi_cmd_send() will not wait 3 seconds, then recovery will be
started quickly and success.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230905105229.10090-1-quic_wgong@quicinc.com
|
|
When hardware rfkill is enabled in the firmware, it will report the
capability using WMI_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY event
to the host. Currently ath12k does not process this service capability. In
order to support this, update ath12k to check if the capability is enabled,
if so, send the GPIO information to firmware. When the firmware detects
hardware rfkill is enabled by the user, it will report it using
WMI_RFKILL_STATE_CHANGE_EVENTID. When ath12k receive the event, it will set
the value of rfkill_radio_on based on whether radio_state is equal to
WMI_RFKILL_RADIO_STATE_ON, then send WMI_PDEV_PARAM_RFKILL_ENABLE to
firmware.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230906110412.182176-1-quic_lingbok@quicinc.com
|
|
- update new features like bloom filter and DEFLATE.
- add documentation for the long xattr name prefixes, which was
landed upstream since v6.4.
Signed-off-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230928134852.31118-1-jefflexu@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
|
|
nfsd4_encode_readv() uses xdr->buf->page_len as a starting point for
the nfsd_iter_read() sink buffer -- page_len is going to be offset
by the parts of the COMPOUND that have already been encoded into
xdr->buf->pages.
However, that value must be captured /before/
xdr_reserve_space_vec() advances page_len by the expected size of
the read payload. Otherwise, the whole front part of the first
page of the payload in the reply will be uninitialized.
Mantas hit this because sec=krb5i forces RQ_SPLICE_OK off, which
invokes the readv part of the nfsd4_encode_read() path. Also,
older Linux NFS clients appear to send shorter READ requests
for files smaller than a page, whereas newer clients just send
page-sized requests and let the server send as many bytes as
are in the file.
Reported-by: Mantas Mikulėnas <grawity@gmail.com>
Closes: https://lore.kernel.org/linux-nfs/f1d0b234-e650-0f6e-0f5d-126b3d51d1eb@gmail.com/
Fixes: 703d75215555 ("NFSD: Hoist rq_vec preparation into nfsd_read() [step two]")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
|
|
Mark attributes which are supposed to be arrays of nested attributes
with known content as such. Originally suggested for
NFTA_RULE_EXPRESSIONS only, but does apply to others as well.
Suggested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
Set netlink extended error reporting for several lookup functions which
allows userspace to infer what is the error cause.
Reported-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
tcp early demux
Test that nat engine resolves the source port clash and tcp packet
is passed to the correct socket.
While at it, get rid of the iperf3 dependency, just use socat for
listener side too.
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
In commit 03a3ca37e4c6 ("netfilter: nf_nat: undo erroneous tcp edemux lookup")
I fixed a problem with source port clash resolution and DNAT.
A very similar issue exists with REDIRECT (DNAT to local address) and
port rewrites.
Consider two port redirections done at prerouting hook:
-p tcp --port 1111 -j REDIRECT --to-ports 80
-p tcp --port 1112 -j REDIRECT --to-ports 80
Its possible, however unlikely, that we get two connections sharing
the same source port, i.e.
saddr:12345 -> daddr:1111
saddr:12345 -> daddr:1112
This works on sender side because destination address is
different.
After prerouting, nat will change first syn packet to
saddr:12345 -> daddr:80, stack will send a syn-ack back and 3whs
completes.
The second syn however will result in a source port clash:
after dnat rewrite, new syn has
saddr:12345 -> daddr:80
This collides with the reply direction of the first connection.
The NAT engine will handle this in the input nat hook by
also altering the source port, so we get for example
saddr:13535 -> daddr:80
This allows the stack to send back a syn-ack to that address.
Reverse NAT during POSTROUTING will rewrite the packet to
daddr:1112 -> saddr:12345 again. Tuple will be unique on-wire
and peer can process it normally.
Problem is when ACK packet comes in:
After prerouting, packet payload is mangled to saddr:12345 -> daddr:80.
Early demux will assign the 3whs-completing ACK skb to the first
connections' established socket.
This will then elicit a challenge ack from the first connections'
socket rather than complete the connection of the second.
The second connection can never complete.
Detect this condition by checking if the associated sockets port
matches the conntrack entries reply tuple.
If it doesn't, then input source address translation mangled
payload after early demux and the found sk is incorrect.
Discard this sk and let TCP stack do another lookup.
Signed-off-by: Florian Westphal <fw@strlen.de>
|
|
Currently, skbs generated by pktgen always have their reference count
incremented before transmission, causing their reference count to be
always greater than 1, leading to two issues:
1. Only the code paths for shared skbs can be tested.
2. In certain situations, skbs can only be released by pktgen.
To enhance testing comprehensiveness, we are introducing the "SHARED"
flag to indicate whether an SKB is shared. This flag is enabled by
default, aligning with the current behavior. However, disabling this
flag allows skbs with a reference count of 1 to be transmitted.
So we can test non-shared skbs and code paths where skbs are released
within the stack.
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Reviewed-by: Benjamin Poirier <bpoirier@nvidia.com>
Link: https://lore.kernel.org/r/20230920125658.46978-2-liangchen.linux@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When specifying an unknown flag, it will print all available flags.
Currently, these flags are provided as fixed strings, which requires
manual updates when flags change. Replacing it with automated flag
enumeration.
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Link: https://lore.kernel.org/r/20230920125658.46978-1-liangchen.linux@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use 'kstrtoul_from_user()' in 'ath11k_write_file_spectral_count()'
and 'ath11k_write_file_spectral_bins()'
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230824075121.121144-4-dmantipov@yandex.ru
|
|
LL TEMAC IP is no longer supported. Hence add an entry marking the
driver as obsolete.
Signed-off-by: Harini Katakam <harini.katakam@amd.com>
Link: https://lore.kernel.org/r/20230920115047.31345-1-harini.katakam@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2023-09-19
Misc updates for mlx5 driver
1) From Erez, Add support for multicast forwarding to multi destination
in bridge offloads with software steering mode (SMFS).
2) From Jianbo, Utilize the maximum aggregated link speed for police
action rate.
3) From Moshe, Add a health error syndrome for pci data poisoned
4) From Shay, Enable 4 ports multiport E-switch
5) From Jiri, Trivial SF code cleanup
====================
Link: https://lore.kernel.org/r/20230920063552.296978-1-saeed@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The 6 bytes length of the tries_buf string in ata_eh_link_report() is
too short and results in a gcc compilation warning with W-!:
drivers/ata/libata-eh.c: In function ‘ata_eh_link_report’:
drivers/ata/libata-eh.c:2371:59: warning: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 4 [-Wformat-truncation=]
2371 | snprintf(tries_buf, sizeof(tries_buf), " t%d",
| ^~
drivers/ata/libata-eh.c:2371:56: note: directive argument in the range [-2147483648, 4]
2371 | snprintf(tries_buf, sizeof(tries_buf), " t%d",
| ^~~~~~
drivers/ata/libata-eh.c:2371:17: note: ‘snprintf’ output between 4 and 14 bytes into a destination of size 6
2371 | snprintf(tries_buf, sizeof(tries_buf), " t%d",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2372 | ap->eh_tries);
| ~~~~~~~~~~~~~
Avoid this warning by increasing the string size to 16B.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The 24 bytes length allocated to the ncq_desc string in
ata_dev_config_lba() for ata_dev_config_ncq() to use is too short,
causing the following gcc compilation warnings when compiling with W=1:
drivers/ata/libata-core.c: In function ‘ata_dev_configure’:
drivers/ata/libata-core.c:2378:56: warning: ‘%d’ directive output may be truncated writing between 1 and 2 bytes into a region of size between 1 and 11 [-Wformat-truncation=]
2378 | snprintf(desc, desc_sz, "NCQ (depth %d/%d)%s", hdepth,
| ^~
In function ‘ata_dev_config_ncq’,
inlined from ‘ata_dev_config_lba’ at drivers/ata/libata-core.c:2649:8,
inlined from ‘ata_dev_configure’ at drivers/ata/libata-core.c:2952:9:
drivers/ata/libata-core.c:2378:41: note: directive argument in the range [1, 32]
2378 | snprintf(desc, desc_sz, "NCQ (depth %d/%d)%s", hdepth,
| ^~~~~~~~~~~~~~~~~~~~~
drivers/ata/libata-core.c:2378:17: note: ‘snprintf’ output between 16 and 31 bytes into a destination of size 24
2378 | snprintf(desc, desc_sz, "NCQ (depth %d/%d)%s", hdepth,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2379 | ddepth, aa_desc);
| ~~~~~~~~~~~~~~~~
Avoid these warnings and the potential truncation by changing the size
of the ncq_desc string to 32 characters.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If an error occurs when resuming a host adapter before the devices
attached to the adapter are resumed, the adapter low level driver may
remove the scsi host, resulting in a call to sd_remove() for the
disks of the host. This in turn results in a call to sd_shutdown() which
will issue a synchronize cache command and a start stop unit command to
spindown the disk. sd_shutdown() issues the commands only if the device
is not already runtime suspended but does not check the power state for
system-wide suspend/resume. That is, the commands may be issued with the
device in a suspended state, which causes PM resume to hang, forcing a
reset of the machine to recover.
Fix this by tracking the suspended state of a disk by introducing the
suspended boolean field in the scsi_disk structure. This flag is set to
true when the disk is suspended is sd_suspend_common() and resumed with
sd_resume(). When suspended is true, sd_shutdown() is not executed from
sd_remove().
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
libsas does its own domain based power management of ports. For such
ports, libata should not use a device type defining power management
operations as executing these operations for suspend/resume in addition
to libsas calls to ata_sas_port_suspend() and ata_sas_port_resume() is
not necessary (and likely dangerous to do, even though problems are not
seen currently).
Introduce the new ata_port_sas_type device_type for ports managed by
libsas. This new device type is used in ata_tport_add() and is defined
without power management operations.
Fixes: 2fcbdcb4c802 ("[SCSI] libata: export ata_port suspend/resume infrastructure for sas")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 6aa0365a3c85 ("ata: libata-scsi: Avoid deadlock on rescan after
device resume") modified ata_scsi_dev_rescan() to check the scsi device
"is_suspended" power field to ensure that the scsi device associated
with an ATA device is fully resumed when scsi_rescan_device() is
executed. However, this fix is problematic as:
1) It relies on a PM internal field that should not be used without PM
device locking protection.
2) The check for is_suspended and the call to scsi_rescan_device() are
not atomic and a suspend PM event may be triggered between them,
casuing scsi_rescan_device() to be called on a suspended device and
in that function blocking while holding the scsi device lock. This
would deadlock a following resume operation.
These problems can trigger PM deadlocks on resume, especially with
resume operations triggered quickly after or during suspend operations.
E.g., a simple bash script like:
for (( i=0; i<10; i++ )); do
echo "+2 > /sys/class/rtc/rtc0/wakealarm
echo mem > /sys/power/state
done
that triggers a resume 2 seconds after starting suspending a system can
quickly lead to a PM deadlock preventing the system from correctly
resuming.
Fix this by replacing the check on is_suspended with a check on the
return value given by scsi_rescan_device() as that function will fail if
called against a suspended device. Also make sure rescan tasks already
scheduled are first cancelled before suspending an ata port.
Fixes: 6aa0365a3c85 ("ata: libata-scsi: Avoid deadlock on rescan after device resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
scsi_rescan_device() takes a scsi device lock before executing a device
handler and device driver rescan methods. Waiting for the completion of
any command issued to the device by these methods will thus be done with
the device lock held. As a result, there is a risk of deadlocking within
the power management code if scsi_rescan_device() is called to handle a
device resume with the associated scsi device not yet resumed.
Avoid such situation by checking that the target scsi device is in the
running state, that is, fully capable of executing commands, before
proceeding with the rescan and bailout returning -EWOULDBLOCK otherwise.
With this error return, the caller can retry rescaning the device after
a delay.
The state check is done with the device lock held and is thus safe
against incoming suspend power management operations.
Fixes: 6aa0365a3c85 ("ata: libata-scsi: Avoid deadlock on rescan after device resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
|
|
The introduction of a device link to create a consumer/supplier
relationship between the scsi device of an ATA device and the ATA port
of that ATA device fixes the ordering of system suspend and resume
operations. For suspend, the scsi device is suspended first and the ata
port after it. This is fine as this allows the synchronize cache and
START STOP UNIT commands issued by the scsi disk driver to be executed
before the ata port is disabled.
For resume operations, the ata port is resumed first, followed
by the scsi device. This allows having the request queue of the scsi
device to be unfrozen after the ata port resume is scheduled in EH,
thus avoiding to see new requests prematurely issued to the ATA device.
Since libata sets manage_system_start_stop to 1, the scsi disk resume
operation also results in issuing a START STOP UNIT command to the
device being resumed so that the device exits standby power mode.
However, restoring the ATA device to the active power mode must be
synchronized with libata EH processing of the port resume operation to
avoid either 1) seeing the start stop unit command being received too
early when the port is not yet resumed and ready to accept commands, or
after the port resume process issues commands such as IDENTIFY to
revalidate the device. In this last case, the risk is that the device
revalidation fails with timeout errors as the drive is still spun down.
Commit 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
disabled issuing the START STOP UNIT command to avoid issues with it.
But this is incorrect as transitioning a device to the active power
mode from the standby power mode set on suspend requires a media access
command. The IDENTIFY, READ LOG and SET FEATURES commands executed in
libata EH context triggered by the ata port resume operation may thus
fail.
Fix these synchronization issues is by handling a device power mode
transitions for system suspend and resume directly in libata EH context,
without relying on the scsi disk driver management triggered with the
manage_system_start_stop flag.
To do this, the following libata helper functions are introduced:
1) ata_dev_power_set_standby():
This function issues a STANDBY IMMEDIATE command to transitiom a device
to the standby power mode. For HDDs, this spins down the disks. This
function applies only to ATA and ZAC devices and does nothing otherwise.
This function also does nothing for devices that have the
ATA_FLAG_NO_POWEROFF_SPINDOWN or ATA_FLAG_NO_HIBERNATE_SPINDOWN flag
set.
For suspend, call ata_dev_power_set_standby() in
ata_eh_handle_port_suspend() before the port is disabled and frozen.
ata_eh_unload() is also modified to transition all enabled devices to
the standby power mode when the system is shutdown or devices removed.
2) ata_dev_power_set_active() and
This function applies to ATA or ZAC devices and issues a VERIFY command
for 1 sector at LBA 0 to transition the device to the active power mode.
For HDDs, since this function will complete only once the disk spin up.
Its execution uses the same timeouts as for reset, to give the drive
enough time to complete spinup without triggering a command timeout.
For resume, call ata_dev_power_set_active() in
ata_eh_revalidate_and_attach() after the port has been enabled and
before any other command is issued to the device.
With these changes, the manage_system_start_stop and no_start_on_resume
scsi device flags do not need to be set in ata_scsi_dev_config(). The
flag manage_runtime_start_stop is still set to allow the sd driver to
spinup/spindown a disk through the sd runtime operations.
Fixes: 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The underlying device and driver of a SCSI disk may have different
system and runtime power mode control requirements. This is because
runtime power management affects only the SCSI disk, while system level
power management affects all devices, including the controller for the
SCSI disk.
For instance, issuing a START STOP UNIT command when a SCSI disk is
runtime suspended and resumed is fine: the command is translated to a
STANDBY IMMEDIATE command to spin down the ATA disk and to a VERIFY
command to wake it up. The SCSI disk runtime operations have no effect
on the ata port device used to connect the ATA disk. However, for
system suspend/resume operations, the ATA port used to connect the
device will also be suspended and resumed, with the resume operation
requiring re-validating the device link and the device itself. In this
case, issuing a VERIFY command to spinup the disk must be done before
starting to revalidate the device, when the ata port is being resumed.
In such case, we must not allow the SCSI disk driver to issue START STOP
UNIT commands.
Allow a low level driver to refine the SCSI disk start/stop management
by differentiating system and runtime cases with two new SCSI device
flags: manage_system_start_stop and manage_runtime_start_stop. These new
flags replace the current manage_start_stop flag. Drivers setting the
manage_start_stop are modifed to set both new flags, thus preserving the
existing start/stop management behavior. For backward compatibility, the
old manage_start_stop sysfs device attribute is kept as a read-only
attribute showing a value of 1 for devices enabling both new flags and 0
otherwise.
Fixes: 0a8589055936 ("ata,scsi: do not issue START STOP UNIT on resume")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There is no direct device ancestry defined between an ata_device and
its scsi device which prevents the power management code from correctly
ordering suspend and resume operations. Create such ancestry with the
ata device as the parent to ensure that the scsi device (child) is
suspended before the ata device and that resume handles the ata device
before the scsi device.
The parent-child (supplier-consumer) relationship is established between
the ata_port (parent) and the scsi device (child) with the function
device_add_link(). The parent used is not the ata_device as the PM
operations are defined per port and the status of all devices connected
through that port is controlled from the port operations.
The device link is established with the new function
ata_scsi_slave_alloc(), and this function is used to define the
->slave_alloc callback of the scsi host template of all ata drivers.
Fixes: a19a93e4c6a9 ("scsi: core: pm: Rely on the device driver core for async power management")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
|
|
Whenever an ATA adapter driver is removed (e.g. rmmod),
ata_port_detach() is called repeatedly for all the adapter ports to
remove (unload) the devices attached to the port and delete the port
device itself. Removing of devices is done using libata EH with the
ATA_PFLAG_UNLOADING port flag set. This causes libata EH to execute
ata_eh_unload() which disables all devices attached to the port.
ata_port_detach() finishes by calling scsi_remove_host() to remove the
scsi host associated with the port. This function will trigger the
removal of all scsi devices attached to the host and in the case of
disks, calls to sd_shutdown() which will flush the device write cache
and stop the device. However, given that the devices were already
disabled by ata_eh_unload(), the synchronize write cache command and
start stop unit commands fail. E.g. running "rmmod ahci" with first
removing sd_mod results in error messages like:
ata13.00: disable device
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
sd 0:0:0:0: [sda] Stopping disk
sd 0:0:0:0: [sda] Start/Stop Unit failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
Fix this by removing all scsi devices of the ata devices connected to
the port before scheduling libata EH to disable the ATA devices.
Fixes: 720ba12620ee ("[PATCH] libata-hp: update unload-unplug")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The function ata_port_request_pm() checks the port flag
ATA_PFLAG_PM_PENDING and calls ata_port_wait_eh() if this flag is set to
ensure that power management operations for a port are not scheduled
simultaneously. However, this flag check is done without holding the
port lock.
Fix this by taking the port lock on entry to the function and checking
the flag under this lock. The lock is released and re-taken if
ata_port_wait_eh() needs to be called. The two WARN_ON() macros checking
that the ATA_PFLAG_PM_PENDING flag was cleared are removed as the first
call is racy and the second one done without holding the port lock.
Fixes: 5ef41082912b ("ata: add ata port system PM callbacks")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
|
|
When the PF and VF drivers both support flexible rx descriptors and have
negotiated the VIRTCHNL_VF_OFFLOAD_RX_FLEX_DESC capability, the VF driver
queries the PF for the list of supported descriptor formats
(VIRTCHNL_OP_GET_SUPPORTED_RXDIDS). The PF driver is supposed to set the
supported_rxdids bits that correspond to the descriptor formats the
firmware implements. The legacy 32-byte rx desc format is always
supported, even though it is not expressed in GLFLXP_RXDID_FLAGS.
The ice driver does not advertise the legacy 32-byte rx desc support,
which leads to this failure to bring up the VF using the Intel
out-of-tree iavf driver:
iavf 0000:41:01.0: PF does not list support for default Rx descriptor format
...
iavf 0000:41:01.0: PF returned error -5 (VIRTCHNL_STATUS_ERR_PARAM) to our request 6
The in-tree iavf driver does not expose this bug, because it does not
yet implement VIRTCHNL_VF_OFFLOAD_RX_FLEX_DESC.
The ice driver must always set the ICE_RXDID_LEGACY_1 bit in
supported_rxdids. The Intel out-of-tree ice driver and the ice driver in
DPDK both do this.
I copied this piece of the code and the comment text from the Intel
out-of-tree driver.
Fixes: e753df8fbca5 ("ice: Add support Flex RXD")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20230920115439.61172-1-mschmidt@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Introduce ifc related stuff to enable migration in a chunk mode.
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://lore.kernel.org/r/20230911093856.81910-2-yishaih@nvidia.com
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Convert list_for_each() to list_for_each_entry() where applicable.
No functional changed.
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230919170409.1581074-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add mitigation for the speculative return stack overflow vulnerability
which exists on Hygon processors too.
Signed-off-by: Pu Wen <puwen@hygon.cn>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/tencent_4A14812842F104E93AA722EC939483CEFF05@qq.com
|
|
Pedro Tammela says:
====================
selftests/tc-testing: parallel tdc
As the number of tdc tests is growing, so is our completion wall time.
One of the ideas to improve this is to run tests in parallel, as they
are self contained.
This series allows for tests to run in parallel, in batches of 32 tests.
Not all tests can run in parallel as they might conflict with each other.
The code will still honor this requirement even when trying to run the
tests over the worker pool.
In order to make this happen we had to localize the test resources
(patches 1 and 2), where instead of having all tests sharing one single
namespace and veths devices each test now gets it's own local namespace and devices.
Even though the tests serialize over rtnl_lock in the kernel, we
measured a speedup of about 3x in a test VM.
====================
Link: https://lore.kernel.org/r/20230919135404.1778595-1-pctammela@mojatatu.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Update the documentation to reflect the changes made to tdc with regards
to minimal requirements and test definitions expectations.
Tested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use a Python process pool to run the tests in parallel.
Not all tests can run in parallel, for instance tests that are not
namespaced and tests that use netdevsim, as they can conflict with one
another.
The code logic will split the tests into serial and parallel.
For the parallel tests, we build batches of 32 tests and queue each
batch on the process pool. For the serial tests, they are queued as a
whole into the process pool, which in turn executes them concurrently
with the parallel tests.
Even though the tests serialize on rtnl_lock in the kernel, this feature
showed results with a ~3x speedup on the wall time for the entire test suite
running in a VM:
Before - 4m32.502s
After - 1m19.202s
Examples:
In order to run tdc using 4 processes:
./tdc.py -J4 <...>
In order to run tdc using 1 process:
./tdc.py -J1 <...> || ./tdc.py <...>
Note that the kernel configuration will affect the speed of the tests,
especially if such configuration slows down process creation and/or
fork().
Tested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
With resources localized on a per test basis, some tests definitions
either contain redundant commands, were wrong or could be simplified.
Update all of them to match the new requirements.
Tested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As of today, the current tdc architecture creates one netns and uses it
to run all tests. This assumption was embedded into the nsPlugin which
carried over as how the tests were written.
The tdc tests are by definition self contained and can,
theoretically, run in parallel. Even though in the kernel they will
serialize over the rtnl lock, we should expect a significant speedup of the
total wall time for the entire test suite, which is hitting close to
1100 tests at this point.
A first step to achieve this goal is to remove sharing of global resources like
veth/dummy interfaces and the netns. In this patch we 'localize' these
resources on a per test basis. Each test gets it's own netns, VETH/dummy interfaces.
The resources are spawned in the pre_suite phase, where tdc will prepare
all netns and interfaces for all tests. This is done in order to avoid
concurrency issues with netns / interfaces spawning and commands using
them. As tdc progresses, the resources are deleted after each test finishes
executing.
Tests that don't use the nsPlugin still run under the root namespace,
but are now required to manage any external resources like interfaces.
These cannot be parallelized as their definition doesn't allow it.
On the other hand, when using the nsPlugin, tests don't need to create
dummy/veth interfaces as these are handled already.
Tested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Enable the generic syscon-poweroff driver used on all Exynos ARM64 SoCs
(e.g. Exynos5433) and few APM SoCs.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Link: https://lore.kernel.org/r/20230901115732.45854-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Fiberstone GPON-ONU-34-20B can operate at 2500base-X, but report 1.2GBd
NRZ in their EEPROM.
The module also require the ignore tx fault fixup similar to Huawei MA5671A
as it gets disabled on error messages with serial redirection enabled.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20230919124720.8210-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The locomolcd driver has one remaining missing-prototype warning:
drivers/video/backlight/locomolcd.c:83:6: error: no previous prototype for 'locomolcd_power' [-Werror=missing-prototypes]
There is in fact an unused prototype with a similar name in a global
header, so move the actual one there and remove the old one.
Link: https://lore.kernel.org/r/20230927194844.680771-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
Arm SCMI fix for v6.6
A single fix to address scmi_perf_attributes_get() using the protocol
version even before it was populated and ending up with unexpected
bogowatts power scale.
* tag 'scmi-fix-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: Fixup perf power-cost/microwatt support
Link: https://lore.kernel.org/r/20230927121604.158645-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes
Arm FF-A fix for v6.6
It has been reported that the driver sets the memory region attributes
for MEM_LEND operation when the specification clearly states not to. The
fix here addresses the issue by ensuring the memory region attributes are
cleared for the memory lending operation.
* tag 'ffa-fix-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_ffa: Don't set the memory region attributes for MEM_LEND
Link: https://lore.kernel.org/r/20230927121555.158619-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Sometimes, our completions race with new master transfers and override
the bus->operation and bus->master_or_slave variables. This causes
transactions to timeout and kernel crashes less frequently.
To remedy this, we re-order all completions to the very end of the
function.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver")
Signed-off-by: William A. Kennington III <william@wkennington.com>
Reviewed-by: Tali Perry <tali.perry1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Otherwise we run the risk of having the lower_xprt freed from underneath
us, causing an oops that looks like this:
[ 224.150698] BUG: kernel NULL pointer dereference, address: 0000000000000018
[ 224.150951] #PF: supervisor read access in kernel mode
[ 224.151117] #PF: error_code(0x0000) - not-present page
[ 224.151278] PGD 0 P4D 0
[ 224.151361] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 224.151499] CPU: 2 PID: 99 Comm: kworker/u10:6 Not tainted 6.6.0-rc3-g6465e260f487 #41264 a00b0960990fb7bc6d6a330ee03588b67f08a47b
[ 224.151977] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS unknown 2/2/2022
[ 224.152216] Workqueue: xprtiod xs_tcp_tls_setup_socket [sunrpc]
[ 224.152434] RIP: 0010:xs_tcp_tls_setup_socket+0x3cc/0x7e0 [sunrpc]
[ 224.152643] Code: 00 00 48 8b 7c 24 08 e9 f3 01 00 00 48 83 7b c0 00 0f 85 d2 01 00 00 49 8d 84 24 f8 05 00 00 48 89 44 24 10 48 8b 00 48 89 c5 <4c> 8b 68 18 66 41 83 3f 0a 75 71 45 31 ff 4c 89 ef 31 f6 e8 5c 76
[ 224.153246] RSP: 0018:ffffb00ec060fd18 EFLAGS: 00010246
[ 224.153427] RAX: 0000000000000000 RBX: ffff8c06c2e53e40 RCX: 0000000000000001
[ 224.153652] RDX: ffff8c073bca2408 RSI: 0000000000000282 RDI: ffff8c06c259ee00
[ 224.153868] RBP: 0000000000000000 R08: ffffffff9da55aa0 R09: 0000000000000001
[ 224.154084] R10: 00000034306c30f1 R11: 0000000000000002 R12: ffff8c06c2e51800
[ 224.154300] R13: ffff8c06c355d400 R14: 0000000004208160 R15: ffff8c06c2e53820
[ 224.154521] FS: 0000000000000000(0000) GS:ffff8c073bd00000(0000) knlGS:0000000000000000
[ 224.154763] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 224.154940] CR2: 0000000000000018 CR3: 0000000062c1e000 CR4: 0000000000750ee0
[ 224.155157] PKRU: 55555554
[ 224.155244] Call Trace:
[ 224.155325] <TASK>
[ 224.155395] ? __die_body+0x68/0xb0
[ 224.155507] ? page_fault_oops+0x34c/0x3a0
[ 224.155635] ? _raw_spin_unlock_irqrestore+0xe/0x40
[ 224.155793] ? exc_page_fault+0x7a/0x1b0
[ 224.155916] ? asm_exc_page_fault+0x26/0x30
[ 224.156047] ? xs_tcp_tls_setup_socket+0x3cc/0x7e0 [sunrpc ae3a15912ae37fd51dafbdbc2dbd069117f8f5c8]
[ 224.156367] ? xs_tcp_tls_setup_socket+0x2fe/0x7e0 [sunrpc ae3a15912ae37fd51dafbdbc2dbd069117f8f5c8]
[ 224.156697] ? __pfx_xs_tls_handshake_done+0x10/0x10 [sunrpc ae3a15912ae37fd51dafbdbc2dbd069117f8f5c8]
[ 224.157013] process_scheduled_works+0x24e/0x450
[ 224.157158] worker_thread+0x21c/0x2d0
[ 224.157275] ? __pfx_worker_thread+0x10/0x10
[ 224.157409] kthread+0xe8/0x110
[ 224.157510] ? __pfx_kthread+0x10/0x10
[ 224.157628] ret_from_fork+0x37/0x50
[ 224.157741] ? __pfx_kthread+0x10/0x10
[ 224.157859] ret_from_fork_asm+0x1b/0x30
[ 224.157983] </TASK>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
This reverts commit 88428cc4ae7abcc879295fbb19373dd76aad2bdd.
The problem this commit is intended to fix was comprehensively fixed
in commit 7de62bc09fe6 ("SUNRPC dont update timeout value on connection
reset").
Since then, this commit has been preventing the correct timeout of soft
mounted requests.
Cc: stable@vger.kernel.org # 5.9.x: 09252177d5f9: SUNRPC: Handle major timeout in xprt_adjust_timeout()
Cc: stable@vger.kernel.org # 5.9.x: 7de62bc09fe6: SUNRPC dont update timeout value on connection reset
Cc: stable@vger.kernel.org # 5.9.x
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
Commit 4dc73c679114 reintroduces the deadlock that was fixed by commit
aeabb3c96186 ("NFSv4: Fix a NFSv4 state manager deadlock") because it
prevents the setup of new threads to handle reboot recovery, while the
older recovery thread is stuck returning delegations.
Fixes: 4dc73c679114 ("NFSv4: keep state manager thread active if swap is enabled")
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
If the NFS4CLNT_RUN_MANAGER flag got set just before we cleared
NFS4CLNT_MANAGER_RUNNING, then we might have won the race against
nfs4_schedule_state_manager(), and are responsible for handling the
recovery situation.
Fixes: aeabb3c96186 ("NFSv4: Fix a NFSv4 state manager deadlock")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
